Electrical and Computer Engineering Commons^™

Plasmonic Nanostructures For The Absorption Enhancement Of Silicon Solar Cells, Nathan Matthias Burford

Graduate Theses and Dissertations

In this work, computational investigation of plasmonic nanostructures was conducted using the commercial finite element electromagnetics solver Ansys® HFSS. Arrays of silver toroid nanoparticles located on the surface of an amorphous silicon thin-film absorbing layer were studied for particle sizes ranging from 20 nm to 200 nm in outer diameter. Parametric optimization by calculating an approximation of the photocurrent enhancement due to the nanoparticles was performed to determine optimal surface coverage of the nanoparticles. A comparison was made between these optimized nanotoroid arrays and optimized nanosphere arrays based on spectral absorption enhancement and potential photocurrent enhancement in an amorphous silicon …

Design And Fabrication Of Nanofluidic Systems With Integrated Sensing Electrodes For Rapid Biomolecule Characterization, Taylor Bradley Busch

Graduate Theses and Dissertations

A transparent nanofluidic system with embedded sensing electrodes was designed and fabricated by integrating Atomic Force Microscopy (AFM) nanolithography, Focused Ion Beam (FIB) milling and metal deposition, and standard microfabrication processing. The fabrication process started with the evaporation of chrome/gold (Cr/Au) onto a Pyrex 7740 wafer followed by photolithography and wet etching of the microchannels. The wafer was patterned a second time to form Au microelectrodes with 15-45 micrometer separation gaps in the nanochannel region. Sensing electrodes (up to one micron wide) were then deposited using FIB to bridge the gaps. The nanochannels were realized through both AFM nanolithography and …

Intermediate Band Solar Cells Based On Inas Quantum Dots Embedded In Ingaas Quantum Well, Ramesh Vasan

Graduate Theses and Dissertations

Intermediate band solar cells based on quantum dots and quantum wells with anti-reflection coating are investigated in this thesis. The demand for high efficient solar cells as an alternate source of energy is the main motivation for this research project. Intermediate band solar cells based on quantum dots were the subject of intensive research in recent years. High power conversion efficiency was predicted from InAs/GaAs intermediate band solar cells as the presence of InAs quantum dots increased the absorption below the band gap of the host material.

In this thesis, an attempt has been made to further increase the absorption …

The Geometry And Sensitivity Of Ion-Beam Sculpted Nanopores For Single Molecule Dna Analysis, Ryan Connor Rollings

Graduate Theses and Dissertations

In this dissertation, the relationship between the geometry of ion-beam sculpted solid-state nanopores and their ability to analyze single DNA molecules using resistive pulse sensing is investigated. To accomplish this, the three dimensional shape of the nanopore is determined using energy filtered and tomographic transmission electron microscopy. It is shown that this information enables the prediction of the ionic current passing through a voltage biased nanopore and improves the prediction of the magnitude of current drop signals when the nanopore interacts with single DNA molecules. The dimensional stability of nanopores in solution is monitored using this information and is improved …

New Effects Of Aging And Lattice Intercalation On Surface Properties Of Titanate Nanobelts, Roger Williams

Graduate Theses and Dissertations

Titanate nanobelts (NBs) have structural characteristics beyond that of clays. Due to a negatively charged lattice matrix of edge-shared TiO6-octahedra, the location of intercalated cations within the interlayer space may dictate the charge-conductions. This environment may in turn govern the lattice-framework's stability and surface properties, based upon our preliminary

data.

On that basis, these nanomaterials have been found in our lab to possess superb biological compatibility that is closely related to the types of the intercalated cations. In addition, a prolonged agitation was proven to enable us to manipulate the titanate NBs' length. In a parallel study, a ripening was …

Cad Tools For Synthesis Of Sleep Convention Logic, Parviz Palangpour

Graduate Theses and Dissertations

This dissertation proposes an automated flow for the Sleep Convention Logic (SCL) asynchronous design style. The proposed flow synthesizes synchronous RTL into an SCL netlist. The flow utilizes commercial design tools, while supplementing missing functionality using custom tools. A method for determining the performance bottleneck in an SCL design is proposed. A constraint-driven method to increase the performance of linear SCL pipelines is proposed. Several enhancements to SCL are proposed, including techniques to reduce the number of registers and total sleep capacitance in an SCL design.

Design And Implementation Of Wireless Point-Of-Care Health Monitoring Systems: Diagnosis For Sleep Disorders And Cardiovascular Diseases, Se Chang Oh

Graduate Theses and Dissertations

Chronic sleep disorders are present in 40 million people in the United States. More than 25 million people remain undiagnosed and untreated, which accounts for over $22 billion in unnecessary healthcare costs. In addition, another major chronic disease is the heart diseases which cause 23.8% of the deaths in the United States. Thus, there is a need for a low cost, reliable, and ubiquitous patient monitoring system. A remote point-of-care system can satisfy this need by providing real time monitoring of the patient's health condition at remote places. However, the currently available POC systems have some drawbacks; the fixed number …

Synthesis And Characterization Of Iron Pyrite Nanocrystals For Photovoltaic Devices, Scott Curtis Mangham

Graduate Theses and Dissertations

Iron pyrite nanocrystals have been synthesized using a hot-injection method with a variety of amines and characterized with properties necessary for photovoltaic devices. The iron pyrite nanocrystals were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, optical absorption, micro-Raman, and micro-Photoluminescence. The optical absorbance spectra showed the large absorption in the visible and near infrared spectral range for the nanocrystals as well as to show the band gap. The face-centered cubic crystal structure of the iron pyrite nanocrystals was shown by matching the measured X-ray diffraction pattern to a face-centered cubic iron pyrite reference pattern. Using Bragg's law …

Iii-V Bismide Optoelectronic Devices, Dongsheng Fan

Graduate Theses and Dissertations

This dissertation explores modeling, molecular beam epitaxy growth, and fabrication of III-V bismide optoelectronic devices, which are of great importance in modern applications of telecommunication, gas sensing, environment monitoring, etc. In the current room-temperature continuous-wave operational GaSb-based type-I InGaAsSb/AlGaInAsSb quantum well laser diodes in 3-4 um mid-wavelength range, the lasing wavelength and performance of the devices are limited due to the lack of hole confinement in the active regions. In this dissertation, a novel GaSb-based GaInAsSbBi material is proposed to replace the conventional InGaAsSb material in the quantum well region, which enables the laser diodes achieve up to 4 µm …

Device Characterization And Compact Modeling Of The Sige Hbt In Extreme Temperature Environments, Beth Olivia Woods

Graduate Theses and Dissertations

The silicon germanium heterojunction bipolar transistor, SiGe HBT, has very high frequency response but limited voltage range. Commercial communication applications in wireless and system integration have driven the development of the SiGe HBT. However, the device's excellent electrical performance goes beyond the commercial environment. The SiGe HBT performs exceptionally at low temperatures. The device DC current gain and AC small-signal gain significantly increase in the cryogenic temperature range. Applications at low temperatures with expansive temperature range specifications need an HBT compact model to accurately represent the device's performance.

In this work, a compact model referenced at 300K was developed to …

Design, Layout, And Testing Of A Silicon Carbide-Based Under Voltage Lock-Out Circuit, Michael Dalan Glover

Graduate Theses and Dissertations

Silicon carbide-based power devices play an increasingly important role in modern power conversion systems. Finding a means to reduce the size and complexity of these systems by even incremental amounts can have a significant impact on cost and reliability. One approach to achieving this goal is the die-level integration of gate driver circuitry with the SiC power devices. Aside from cost reductions, there are significant advantages to the integration of the gate driver circuits with the power devices. By integrating the gate driver circuitry with the power devices, the parasitic inductances traditionally seen between the gate driver and the switching …

Synthesis Of Optimized Inp/Zns Core/Shell Nanocrystals And Tio2 Nanotubes For Quantum Dot Sensitized Solar Cells, Seungyong Lee

Graduate Theses and Dissertations

Synthesis of InP/ZnS core/shell nanocrystals and TiO₂ nanotubes and the optimization study to couple them together were explored for quantum dot sensitized solar cells. Its intrinsic nontoxicity makes the direct band gap InP/ZnS core/shell be one of the most promising semiconductor nanocrystals for optoelectric applications, with the advantage of tuning the optical absorption range in the desired solar spectrum region. Highly luminescent and monodisperse InP/ZnS nanocrystals were synthesized in a non-coordinating solvent. By varying the synthesis scheme, different size InP/ZnS nanocrystals with emission peaks ranging from 520 nm to 620 nm were grown. For the purpose of ensuring air …

Development Of Mems-Based Corrosion Sensor, Feng Pan

Graduate Theses and Dissertations

This research is to develop a MEMS-based corrosion sensor, which is used for monitoring uniform, galvanic corrosion occurring in infrastructures such as buildings, bridges. The corrosion sensor is made up of the composite of micro/nano metal particles with elastomers. The mechanism of corrosion sensor is based on the mass transport of corrosive species through the sensor matrix. When the metal particles in the matrix corrode, the electrical resistivity of the material increases due to increasing particle resistances or reduction of conducting pathways. The corrosion rate can be monitored by detecting the resistivity change in sensing elements. The life span of …

Performance And Cost Analysis Of A Structured Concrete Thermocline Thermal Energy Storage System, Matt Nicholas Strasser

Graduate Theses and Dissertations

Increasing global energy demands and diminishing fossil fuel resources have raised increased interest in harvesting renewable energy resources. Solar energy is a promising candidate, as sufficient irradiance is incident to the Earth to supply the energy demands of all of its inhabitants. At the utility scale, concentrating solar power (CSP) plants provide the most cost-efficient method of harnessing solar energy for conversion to electrical energy. A major roadblock to the large-scale implementation of CSP plants is the lack of thermal energy storage (TES) that would allow the continued production of electricity during the absence of constant irradiance. Sensible heat TES …

Computational Design Of The Electrical And Mechanical Performance Of Steerable Mems Antennas, Morgan Andrew Roddy

Graduate Theses and Dissertations

This thesis describes the origins, improvements, and variations of a broadband microwave antenna that can be beam-steered by a micro-electromechanical system (MEMS). The steerable MEMS antenna of this work was comprised of a planar antenna on top of a Silicon membrane. The membrane is etched to create a gimbal hinge structure and a platform which supported the antenna and gave it one or two degrees of freedom of rotation. The antennas presented were broadband and fed by a coplanar waveguide (CPW) transmission line which traversed the hinge structure. The antenna's orientation in space was designed to be changed through electrostatic …

Design And Analysis Of An Adaptive Asynchronous System Architecture For Energy Efficiency, Brent Michael Hollosi

Graduate Theses and Dissertations

Power has become a critical design parameter for digital CMOS integrated circuits. With performance still garnering much concern, a central idea has emerged: minimizing power consumption while maintaining performance. The use of dynamic voltage scaling (DVS) with parallelism has shown to be an effective way of saving power while maintaining performance. However, the potency of DVS and parallelism in traditional, clocked synchronous systems is limited because of the strict timing requirements such systems must comply with. Delay-insensitive (DI) asynchronous systems have the potential to benefit more from these techniques due to their flexible timing requirements and high modularity. This dissertation …

Topics On Light-Emitting-Diode Driver Research, Jaber Hasan

Graduate Theses and Dissertations

In this dissertation, light-emitting-diode (LED) drivers are investigated for efficiency issues related to driving Red-Green-Blue (RGB) pixels and multiple LED strings in parallel. A high-efficiency digitally controlled RGB LED driver was designed for driving a 3x3 RGB LED display panel. A multiplexer was used to sense the voltage drop across the current controllers. This driver maintained a minimum drive voltage across the RGB LED pixels required to keep it in regulation leading to a reduction of unwanted power losses in the RGB LED pixels by selecting the minimum drop across the current-controllers as the reference voltage of the digital controller. …

Energy And Spectral Efficient Wireless Communications, Guoqing Zhou

Graduate Theses and Dissertations

Energy and spectrum are two precious commodities for wireless communications. How to improve the energy and spectrum efficiency has become two critical issues for the designs of wireless communication systems. This dissertation is devoted to the development of energy and spectral efficient wireless communications. The developed techniques can be applied to a wide range of wireless communication systems, such as wireless sensor network (WSN) designed for structure health monitoring (SHM), medium access control (MAC) for multi-user systems, and cooperative spectrum sensing in cognitive radio systems.

First, to improve the energy efficiency in SHM WSN, a new ultra low power (ULP) …

Thermal And Electrical Parasitic Modeling For Multi-Chip Power Module Layout Synthesis, Zihao Gong

Graduate Theses and Dissertations

This thesis presents thermal and electrical parasitic modeling approaches for layout synthesis of Multi-Chip Power Modules (MCPMs). MCPMs integrate power semiconductor devices and drive electronics into a single package. As the switching frequency of power devices increases, the size of the passive components are greatly reduced leading to gains in efficiency and cost reduction. In order to increase switching frequency, electrical parasitics in MCPMs need to be reduced through tighter electronic integrations and smaller packages. As package size is decreased, temperature increases due to less heat dissipation capability. Thus, it is crucial to consider both thermal and electrical parasitics in …

Study Of Current Optocoupler Techniques And Applications For Isolation Of Sensing And Control Signals In Dc-Dc Converters, Jake Williams

Graduate Theses and Dissertations

There is a need for power switches that can operate at high voltage, high temperature, and high switching frequencies with low losses. Power switches fabricated from wide bandgap materials such as silicon carbide (SiC) or gallium nitride (GaN) can outperform conventional silicon switches due to material property advantages. Another common problem in grid-connected applications is the need for high voltage-isolation of gate drivers and control circuitry while operating efficiently at the high switching frequencies, high power density, and high temperatures made possible by wide bandgap devices. Transformers cannot operate at the temperatures of these wide bandgap devices and a new …

A Silicon Carbide Based Solid-State Fault Current Limiter For Modern Power Distribution Systems, Erik Darnell Johnson

Graduate Theses and Dissertations

The fault current limiter represents a developing technology which will greatly improve the reliability and stability of the power grid. By reducing the magnitude of fault currents in distribution systems, fault current limiters can alleviate much of the damage imposed by these events. Solid-state fault current limiters in particular offer many improved capabilities in comparison to the power system protection equipment which is currently being used for fault current mitigation. The use of silicon carbide power semiconductor devices in solid-state fault current limiters produces a system that would help to advance the infrastructure of the electric grid.

A solid-state fault …

Plasmonic And Photonic Designs For Light Trapping In Thin Film Solar Cells, Liming Ji

Graduate Theses and Dissertations

Thin film solar cells are promising to realize cheap solar energy. Compared to conventional wafer cells, they can reduce the use of semiconductor material by 90%. The efficiency of thin film solar cells, however, is limited due to insufficient light absorption. Sufficient light absorption at the bandgap of semiconductor requires a light path more than 10x the thickness of the semiconductor. Advanced designs for light trapping are necessary for solar cells to absorb sufficient light within a limited volume of semiconductor. The goal is to convert the incident light into a trapped mode in the semiconductor layer.

In this dissertation, …

The Development And Packaging Of A High-Density, Three-Phase, Silicon Carbide (Sic) Motor Drive, Jared Hornberger

Graduate Theses and Dissertations

Technology advances within the power electronics field are resulting in systems characterized by higher operating efficiencies, reduced footprint, minimal form factor, and decreasing mass. In particular, these attributes and characteristics are being inserted into numerous consumer applications, such as light-emitting diode lighting, compact fluorescent lighting, smart phones, and tablet PCs, to industrial applications that include hybrid, electric, and plug-in electric vehicles and more electric aircraft. To achieve the increase in energy efficiency and significant reduction in size and mass of these systems, power semiconductor device manufacturers are developing silicon carbide (SiC) semiconductor technology.

In this dissertation, the author discusses the …

Optimization Of Nonlinear Switch Cells For Switching Converters, Bradley Alan Reese

Graduate Theses and Dissertations

Switch cells consist of an array of power switches and passive components which can replace the main switches alone in many power topologies, allowing reduced switching loss without altering the power topology directly. This thesis discusses the development of a switch cell topology that utilizes a saturable resonant inductor to reduce the size and power loss of the cell. Additionally, the cell transfers energy stored in the inductor into a capacitor for efficient energy storage during the cell's conduction region. This energy is then transferred back to the system when the cell turns off, thus reducing the total switching energy.

Flexible Circuits For Aerospace Applications With Special Emphasis On Rf Connectors, Abhishek Nareshraj Singh

Graduate Theses and Dissertations

The current work focused on the study of flexible electronic circuits for use in aerospace applications with emphasis on RF Connectors. The electrical and mechanical performance of the flexible circuits was studied and compared to a standard coaxial cable for feasibility study in avionics space. Also, Anisotropic Conductive Films (ACF) are studied for connecting the flexible RF connectors and their performance studied for electrical and mechanical behavior with change in bonding parameters.

Comparison Of Various Pipelined And Non-Pipelined Scl 8051 Alus, Jingyi Zhao

Graduate Theses and Dissertations

This paper describes the development of an 8-bit SCL 8051 ALU with two versions: SCL 8051 ALU with nsleep and sleep signals and SCL 8051 ALU without nsleep. Both versions have combinational logic (C/L), registers, and completion components, which all utilize slept gates. Both three-stage pipelined and non-pipelined designs were examined for both versions. The four designs were compared in terms of area, speed, leakage power, average power and energy per operation. The SCL 8051 ALU without nsleep is smaller and faster, but it has greater leakage power. It also has lower average power, and less energy consumption than …

Ultra-Low Voltage Digital Circuits And Extreme Temperature Electronics Design, Aaron J. Arthurs

Graduate Theses and Dissertations

Certain applications require digital electronics to operate under extreme conditions e.g., large swings in ambient temperature, very low supply voltage, high radiation. Such applications include sensor networks, wearable electronics, unmanned aerial vehicles, spacecraft, and energyharvesting systems. This dissertation splits into two projects that study digital electronics supplied by ultra-low voltages and build an electronic system for extreme temperatures. The first project introduces techniques that improve circuit reliability at deep subthreshold voltages as well as determine the minimum required supply voltage. These techniques address digital electronic design at several levels: the physical process, gate design, and system architecture. This dissertation analyzes …

Fabrication And Characterization Of Thinner Solid-State Nanopores, Denis Forbi Tita

Graduate Theses and Dissertations

Solid State nanopores that are fabricated by the ion beam sculpting process and electron beam drilling have shown great promise as a sensing device for DNA and protein molecules. Even though biological pores such as the alpha-Haemolysin have been in use for quite some time, the use of solid state Nanopores in single biomolecule detection has been on the rise since the mid 1990s. Solid State nanopores have an advantage over biological pores in that they are more robust, stable, and can be sculpted to any desired size for use in translocation experiments. One of the major challenges in Nanopore …

Delay Insensitive Ternary Logic Utilizing Cmos And Cntfet, Ravi Sankar Parameswaran Nair

Graduate Theses and Dissertations

As digital circuit design continues to evolve due to progress of semiconductor processes well into the sub 100nm range, clocked architectures face limitations in a number of cases where clockless asynchronous architectures require substantially less power, generate less noise, and produce less electromagnetic interference (EMI). This dissertation develops the Delay Insensitive Ternary Logic (DITL) asynchronous design paradigm that combines the designs aspects of similar Dual-Rail asynchronous paradigms and Boolean logic to create a single wire per bit, three voltage signaling and logic scheme.

DITL is designed at the transistor level using multi-threshold CMOS and carbon nanotube (CNT) FETs to develop …

A Silicon Carbide Linear Voltage Regulator For High Temperature Applications, Javier Antonio Valle Mayorga

Graduate Theses and Dissertations

Current market demands have pushed the capabilities of silicon to the edge. High temperature and high power applications require a semiconductor device to operate reliably in very harsh environments. This situation has awakened interests in other types of semiconductors, usually with a higher bandgap than silicon's, as the next venue for the fabrication of integrated circuits (IC) and power devices. Silicon Carbide (SiC) has so far proven to be one of the best options in the power devices field.

This dissertation presents the first attempt to fabricate a SiC linear voltage regulator. This circuit would provide a power management option …