Electrical and Computer Engineering Commons^™

Absorption Imaging Studies On Intrinsic Gaas, John Samuel Kenney

Electrical & Computer Engineering Theses & Dissertations

A diagnostic technique has been developed which allows recording of the temporal and spatial development of electric field structures in GaAs photoconductive switches. The optical method is based on the Franz-Keldysh effect. Measurements were performed with a Nd:YAG activation laser and a GaAs laser diode as the probe laser. At low applied voltages a 100 atm wide region of high electric field is seen at the cathode only. With increasing voltage strong domain like structures emerge at the anode also. A calibration measurement shows that the electric fields in these domains are well above 50 kV/cm. At a threshold voltage, …

Study Of Single-Fiber Fiber Optic Lever Microphone, Trung Duc Nguyen

Electrical & Computer Engineering Theses & Dissertations

Fiber optic sensors are widely used in today's technological applications, providing many advantages that conventional sensors lack. In particular, there is a demand in hypersonic applications to develop microphones to measure acoustic pressure that performs in high temperature and noisy surroundings. This thesis analyzes fiber optic lever microphones (FOLM), since they perform at high temperatures. An FOLM system is an intensity modulated sensor, which is simple to implement and is small in size. Two models of the FOLM have been fabricated and calibrated. The first model uses a seven-element fiber array while the second uses a single-fiber to transmit and …

Influence Of Processing Techniques On Copper Deep Levels Formation And On Photoconductivity In Silicon Doped Gallium Arsenide, Lucy M. Thomas

Electrical & Computer Engineering Theses & Dissertations

Diffusion of copper in silicon doped gallium arsenide under different diffusion conditions is studied. Copper compensated silicon doped gallium arsenide (GaAs:Si:Cu) is used as switch material for bulk optically controlled semiconductor switch, and on-state photoconductivity of the switch is primarily due to the properties of the copper deep levels introduced in the material during diffusion. Gallium arsenide being a compound semiconductor, presence of vacancies and defects make the study of diffusion a complex process. The objective of the current research is twofold: a) to study the influence of diffusion conditions and processing techniques on copper deep level formation in silicon …

A Performance Prediction Model For A Fault-Tolerant Computer During Recovery And Restoration, Rodrigo A. Obando

Electrical & Computer Engineering Theses & Dissertations

The modeling and design of a fault-tolerant multiprocessor system is addressed in this dissertation. In particular, the behavior of the system during recovery and restoration after a fault has occurred is investigated. Given that a multicomputer system is designed using the Algorithm to Architecture To Mapping Model (ATAMM) model, and that a fault (death of a computing resource) occurs during its normal steady-state operation, a model is presented as a viable research tool for predicting the performance bounds of the system during its recovery and restoration phases. Furthermore, the bounds of the performance behavior of the system during this transient …

Robot Force Velocity Control Using Expert System For Control Mode Changes, William R. Doggett

Electrical & Computer Engineering Theses & Dissertations

The most important property of an automated mechanical system is reliable execution of a specified task. Automated mechanical systems work best in precisely structured environments where all operations are repeatable. Typically, these systems are difficult to modify and expensive to install. Sensors can be used to detect disturbances, thus reducing hardware cost by offsetting the need for precise rigid construction components. Sensors, however, increase the complexity and cost of the control software. Efficient methods of reacting to sensor information during automated system operation are required to reduce software complexity and expense.

This thesis analyzes a robotic construction task and describes …

Recognition Of Quadric Surfaces From Range Data: An Analytical Approach, Ivan X. D. D'Cunha

Electrical & Computer Engineering Theses & Dissertations

In this dissertation, a new technique based on analytic geometry for the recognition and description of three-dimensional quadric surfaces from range images is presented. Beginning with the explicit representation of quadrics, a set of ten coefficients are determined for various three-dimensional surfaces. For each quadric surface, a unique set of two-dimensional curves which serve as a feature set is obtained from the various angles at which the object is intersected with a plane. Based on a discriminant method, each of the curves is classified as a parabola, circle, ellipse, hyperbola, or a line. Each quadric surface is shown to be …

The Effect Of Contacts On The Performance Of Electron-Beam Controlled Gaas And Diamond Switches, Michael Kevin Kennedy

Electrical & Computer Engineering Theses & Dissertations

The performance of GaAs and diamond as electron-beam controlled closing and opening switches has been studied. An emphasis has been placed on the effect of contacts on the current-voltage characteristics. The two materials studied were GaAs and diamond. Using the same semi-insulating GaAs wafer as a source of material, a bulk device and a p-i-n device have been fabricated and compared. The asymmetry of the pin diode allows operation at higher voltage because of the ability to suppress the lock-on effect. Whereas GaAs was ionized through cathodoluminescence; diamond, in the form of thin films, has been directly ionized by the …

Design And Implementation Of Fuzzy Logic Controllers, Osama A. Abihana

Electrical & Computer Engineering Theses & Dissertations

The main objectives of our research are to present a self-contained overview of fuzzy sets and fuzzy logic, develop a methodology for control system design using fuzzy logic controllers, and to design and implement a fuzzy logic controller for a real system. In this thesis we first present the fundamental concepts of fuzzy sets and fuzzy logic. Fuzzy sets and basic fuzzy operations are defined. In addition, for control systems, it is important to understand the concepts of linguistic variables, linguistic values, term sets, fuzzy rule base, inference methods, and defuzzification methods. Second, we introduce a four-step fuzzy logic control …

An Application Of Neural Networks In Data Communication Real-Time Resource Reallocation, Qing Fan

Electrical & Computer Engineering Theses & Dissertations

This thesis presents an application of artificial neural networks in real-time resource reallocation, a methodology used in the implementation of an intelligent interface node in the Computer Integrated Manufacturing (CIM) environment. In particular, the problem is formulated using a Hopfield neural network model. The real-time reallocation problem is mapped into a two-dimensional matrix of neurons similar to Hopfield and Tank's approach to the traveling salesman problem (TSP) . An energy function is formulated in terms of the hard constraints and the solution cost. The interconnection weights and the input biases are determined by the energy function. It is shown through …

A Novel Technique For Deep Level Characterization Of High-Resistivity Semiconductor Materials, Sridhar Panigrahi

Electrical & Computer Engineering Theses & Dissertations

An improved photo induced current transient spectroscopy (PICTS) technique is developed for studying deep level parameters in high-resistivity semiconductor materials. A new digital data acquisition approach and improvement in the cryogenics of the system have enabled us, for the first time in our laboratory, to detect CuA level in a copper doped silicon compensated gallium arsenide (GaAs:Si:Cu) sample. The digital approach improves both the signal to noise ratio (S/N) and the efficiency of the system. Also, multiple PICTS spectra in a single thermal cycle can be obtained. In the present work, various doped and undoped gallium arsenide ( GaAs) and …

Text-Independent Automatic Speaker Identification Using Partitioned Neural Networks, Laszlo Rudasi

Electrical & Computer Engineering Theses & Dissertations

This dissertation introduces a binary partitioned approach to statistical pattern classification which is applied to talker identification using neural networks. In recent years artificial neural networks have been shown to work exceptionally well for small but difficult pattern classification tasks. However, their application to large tasks (i.e., having more than ten to 20 categories) is limited by a dramatic increase in required training time. The time required to train a single network to perform N-way classification is nearly proportional to the exponential of N. In contrast, the binary partitioned approach requires training times on the order of N². …

Neural Network Based Vowel Articulation Training Aid For The Deaf, Andrew E. Beck

Electrical & Computer Engineering Theses & Dissertations

Teaching the hearing-impaired to speak is both a challenging and rewarding task. Computer-based training aids are valuable teaching tools and complement the speech therapist in the speech training process. We have developed a computer based vowel articulation training aid designed to provide visual feedback for vowel production to the hearing-impaired user. This system transforms speech spectra from a multi-dimensional acoustic space to a two-dimensional phonetic space which is displayed on a computer monitor. The system signal processing includes feature extraction designed to mimic the properties of the human ear, and a transformation to a two-dimensional display space. The dimensionality transformation …

Formant Estimation From Dctc's Using A Feedforward Neural Network, Shubhangi U. Kelkar

Electrical & Computer Engineering Theses & Dissertations

Formants are the natural frequencies of the human vocal tract. Existing methods for estimating formants from speech signals are computationally complex and subject to errors for certain type of speech sounds. This thesis describes a method for estimating vowel formant frequencies from Discrete Cosine Transform Coefficients (DCTC's), a form of cepstral coefficients, using a feedforward neural network with back-propagation training. Experimental results are based on a large multispeaker data base. The results are obtained for both a linear transformation and a feedforward neural network with a nonlinear hidden layer. In general, the neural network transformation is superior to the linear …

Topics In Nonlinear Stochastic Control, Estimation, And Decision, Using A Measure Transformation Approach, Charalambos Demetriou Charalambous

Electrical & Computer Engineering Theses & Dissertations

We discuss topics in the theory of nonlinear stochastic control, estimation, and decision via a probabilistic approach using measure transformations and martingale theory. First, we investigate the problem of estimating a diffusion process using coordinate transformations and measure transformations, both locally and globally; this is the analog of nonlinear coordinate and state feedback transformations used to obtain exact linearization in nonlinear deterministic control problems. Our results are new in that we use a probabilistic approach rather than a purely geometric one, and also in that we derive representations when the processes are defined locally rather than just globally. A gauge …

Bounds On Constraint Weight Parameters Of Hopfield Networks For Stability Of Optimization Problem Solutions, Gursel Serpen

Electrical & Computer Engineering Theses & Dissertations

The purpose of the presented research is to study the convergence characteristics of Hopfield network dynamics. The relation between constraint weight parameter values and the stability of solutions of constraint satisfaction and optimization problems mapped to Hopfield networks is investigated. A theoretical development relating constraint weight parameter values to solution stability is presented. The dependency of solution stability on constraint weight parameter values is shown employing an abstract optimization problem. A theorem defining bounds on the constraint weight parameter magnitudes for solution stability of constraint satisfaction and optimization problems is proved. Simulation analysis on a set of optimization and constraint …

Study Of Cathodoluminescence In Semiconductors, Mandakini V. Kale

Electrical & Computer Engineering Theses & Dissertations

Cathodoluminescence in Zn doped GaAs and ZnSe, the materials of interest for electron-beam controlled semiconductor switches, has been investigated. A new diagnostic technique, using telescopic setup of lenses, was developed to study the spatially resolved cathodoluminescence. The setup eliminated the light, other than rays from the sample, parallel to the optical axis, resulting in an enhanced spatial resolution. At high e-beam energies, light was detected, from the Zn layer region in the GaAs. It is proposed to be due to the radiative recombination of electron-hole pairs, created by the e-beam. For the polycrystalline ZnSe no light emission was detected. This …

Cathodoluminescence Of Gaas, Tyler Smith

Electrical & Computer Engineering Theses & Dissertations

Cathodoluminescence of band-gap radiation across the bulk of a proposed semiconductor switch has been studied. Such a device relies on the efficient use of cathodoluminescence to modulate the conductivity of the switch. Diagnostics were configured to measure the intensity of band-gap radiation across the bulk of several switch samples. The measured results were compared to calculations based on a four energy level band-gap model which included two deep levels EL2 and HL10.

Q Improvement Of A 5.2 Ghz Te011 Cavity By Incorporating Y1Ba2Cu3O7-X, R. Joseph Leclear

Electrical & Computer Engineering Theses & Dissertations

Research is undertaken to apply high temperature superconducting material to improve the quality factor (Q) of a 5.2 GHz cylindrical resonant cavity. In particular, the approach is to electrophoretically deposit polycrystalline Y₁Ba₂Cu₃O_7-x (YBCO) on the conducting surface of the cavity cylinder. Spalling of the YBCO ceramic coating due to expansion and contraction of the cavity during sintering and testing is overcome by segmenting the cylinder. Results show that the Q of the cavity is increased over that of a copper cavity at temperatures below 60 K. At 20 K, improvement exceeds a factor …

Analytical Modeling And Simulation For Investigation Of A Digital Gas Filter Correlation Radiometer, Catherine P. Mcgowan

Electrical & Computer Engineering Theses & Dissertations

This thesis investigates a digital gas filter correlation radiometer called the Tropospheric Radiometer for Atmospheric Chemistry and Environmental Research (TRACER), which will be used to remotely measure carbon monoxide at three levels in the troposphere. The nadir-viewing radiometer measures the differential absorption of radiation through the atmosphere at 4.67@m and 2.33pm wavelengths. This thesis develops an analytical model of the TRACER measurement process to evaluate the effect of varying certain system parameters on the measurement. The independent sampling criterion and the response of linear systems to random signals are explained. A parametric simulation model is also developed to evaluate the …

The Breakdown Mechanism Of Hollow Cathode Discharge, Mai Tuyet Ngo

Electrical & Computer Engineering Theses & Dissertations

In a low pressure discharge, if the cathode incorporates a cylindrical or slit shaped hole, the discharge current can be several orders of magnitude higher than in one with plane parallel electrodes under the same pressure and voltage conditions. In this work hollow cathode discharges in Helium under the influence of variable parameters such as gas pressure, applied voltage, electrode gap spacing, external magnetic field, etc., are investigated by means of electrical and optical diagnostic techniques.

The results indicate that a hollow cathode discharge develops in two stages. The initial breakdown occurs along the longest straight path of the system, …

An Erasable Optical Memory Based On Stimulated Electronic Transition Concept, James D. Satira

Electrical & Computer Engineering Theses & Dissertations

Erasable optical memory systems with a high storage density and a large data transfer rate are required for many real time data acquisition systems such as those placed aboard NASA's space born platforms. A new concept for erasable optical memory involving stimulated electronic transitions (SET) will meet these requirements. The SET concept useful in erasable optical storage systems was demonstrated in MgS and SrS doped with Eu and Sm. The optical properties of these materials were studied. The reading and writing wavelengths for these samples were determined to be 950 and 514 nm respectively. The peaks of the emission spectra …

Signal Processing Methodologies For An Acoustic Fetal Heart Rate Monitor, Robert A. Pretlow Iii

Electrical & Computer Engineering Theses & Dissertations

Research and development is presented of real time signal processing methodologies for the detection of fetal heart tones within a noise-contaminated signal from a passive acoustic sensor. A linear predictor algorithm is utilized for detection of the heart tone event and additional processing derives heart rate. The linear predictor is adaptively "trained" in a least mean square error sense on generic fetal heart tones recorded from patients. A real time monitor system is described which outputs to a strip chart recorder for plotting the time history of the fetal heart rate. The system is validated in the context of the …

Monte Carlo Simulation Of Millimeter-Wave Gunn Effect Oscillators, Ramani Vaidyanathan

Electrical & Computer Engineering Theses & Dissertations

Monte Carlo simulations have been carried out to investigate the performance of microwave Gunn oscillators. Three separate aspects of the simulation problem have been comprehensively addressed in this work. First, the presence of an external circuit has been self-consistently incorporated into the calculations. The inclusion of the external circuit facilitates a study of the circuit controlled regime, and correctly models effects arising from the time dependent boundary conditions. Secondly, microscopic details of the electronic relaxation mechanisms which ultimately control the frequency response limits, have been taken into account through an iterative Monte Carlo-Poisson scheme. This procedure overcomes a potential shortcoming …

The Modeling Of The Interactions Of Pellets With Magnetic Fusion Plasmas For Alpha Particle Diagnostics, Abdel-Ghafar Mahmood El-Cashlan

Electrical & Computer Engineering Theses & Dissertations

A model for the interactions of hydrogen and carbon pellets with thermonuclear fusion plasmas has been developed and solved to determine the charge-state spatial distributions in the ablation cloud surrounding the pellet. The ionization is treated in a self-consistent manner in the energy balance and the collisional radiative (CR) model is used to calculate the ionization levels. External plasma electron effects on ionization are included. The electron heat flux is modeled as a multigroup distribution. The channelling of the flow along the field line is treated phenomenologically by restricting the cross-sectional area of the flow. The predictions of the model …

Measurement Of Thermal Noise In Condenser Microphones In A Vacuum-Isolation Vessel, Kim Chi Thi Ngo

Electrical & Computer Engineering Theses & Dissertations

The electrical noise generated by thermal agitation of the air molecules impinging upon the membrane of a condenser microphone and from its associated preamplifier has been studied analytically and experimentally over a wide bandwidth. These background noise levels constitute one of the most important specifications of a microphone for they determine the lowest sound pressure that can be detected. Therefore, a new method for measuring the thermal agitation noise within a bandwidth of 1-25600 Hz has been developed. The theoretical and experimental measurements of thermal agitation noise in a condenser microphone by enclosing the microphone in a vessel which is …

Optical And High Electric Field Effects In Bulk Gallium Arsenide Switches, Randy Roush

Electrical & Computer Engineering Theses & Dissertations

During the past few years, bulk, photoconductive switching has become recognized as a viable topic for future research on moderate and high power switches. The two-pulse, or BOSS, concept relies on an excitation laser pulse, and a separate de-excitation pulse in conjunction with silicon doped, copper compensated, GaAs to create a variable temporal electrical pulse width. The research contained in this document provides information concerning the feasibility of the BOSS concept, as the switch is scaled to larger sizes, and higher voltage and current. The major concern will be the high voltage and current effects. The absorption length for 1064 …

Deep Level Characterization Studies In Gaas, Gordhan R. Barevadia

Electrical & Computer Engineering Theses & Dissertations

The goal of this research was to investigate deep levels in different types of GaAs, a material for high power optically controlled bulk semiconductor switches. For low resistivity semiconductors, such as silicon doped GaAs material (p =0.054 Ω cm), deep level transient spectroscopy (DLTS) was used to characterize deep levels. Three deep levels (EL6, EL3, and EL2) have been detected in this material. For high resistivity semiconductors (p > 10⁴ Ω cm), difficulty of electrical carrier injection and of making a junction does not permit the use of DLTS technique. Therefore, an experimental set-up of the photo-induced current transient spectroscopy …

A Comparative Study Of Spectral Peaks Versus Global Spectral Shape As Invariant Acoustic Cues For Vowels, Amir Jalali Jagharghi

Electrical & Computer Engineering Theses & Dissertations

The primary objective of this study was to compare two sets of vowel spectral features, formants and global spectral shape parameters, as invariant acoustic cues to vowel identity. Both automatic vowel recognition experiments and perceptual experiments were performed to evaluate these two feature sets. First, these features were compared using the static spectrum sampled in the middle of each steady-state vowel versus features based on dynamic spectra. Second, the role of dynamic and contextual information was investigated in terms of improvements in automatic vowel classification rates. Third, several speaker normalizing methods were examined for each of the feature sets. Finally, …

An Artificial Neural Approach To The Decomposition Problem, Chandrashekar L. Masti

Electrical & Computer Engineering Theses & Dissertations

The goal of this thesis is to develop an artificial neural approach toward addressing the intractability involved with the decomposition problem. The search for the lattice of substitution property (s. p.) partitions essential to decompositions is cast into the framework of constraint satisfaction. An artificial neural network is developed to provide solutions by performing optimization of a mathematically derived objective function over the problem space. The issue of transitivity is verified to belong to a class of problems beyond the scope of solvability for conventional quadratic-order constraint satisfaction neural networks. A theorem is stated and proved establishing that third-order correlations …

Visual Speech Training Aid For The Deaf, Subhashri Venkat

Electrical & Computer Engineering Theses & Dissertations

A computer-based vowel articulation training aid has been developed. A "continuous" acoustic-phonetic transformation is performed to map speech parameters to a lower dimensionality display space. There are two possible approaches to this transformation problem. The transformation could be either linear or a combination nonlinear/linear. The nonlinear transformation is performed using a multi-layered feedforward neural network with linear output layers. Speech parameters are extracted either from an analog filter bank arrangement (band energies) or by a digital signal processing procedure (Discrete Cosine Transform Coefficients). The speech parameters obtained from both methods correspond to the spectral envelope of the speech signals. The …