Hardware Systems Commons^™

Hardware-In-The-Loop Evaluation Of Sensor-Source Selection For Prosthetic Locomotion Intent Recognition, Victoria Asencio-Clemens

Master's Theses

Active lower-limb prostheses use intent-recognition systems to identify a user’s locomotion mode and select an appropriate control strategy, but sensor configurations that perform well offline may be unsuitable for resource-constrained embedded hardware. Existing sensor-selection methods generally prioritize classification accuracy without directly accounting for processing latency, memory usage, or other hardware-dependent requirements. To address this limitation, this thesis develops a hardware-in-the-loop source-selection framework for embedded classification of level walking, ramp ascent, ramp descent, stair ascent, and stair descent using multimodal biomechanical data from transtibial amputee participants. Subject-specific linear support vector machine classifiers were evaluated using trial-held-out validation, and candidate configurations from …

System Integration And Validation Of The Cal Poly Spacecraft Attitude Dynamics Simulator Mk. Iv, Bricen S. Rigby

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project that seeks to enable the simulation and validation of sensors, actuators, and control logic related to spacecraft attitude control. The SADS platform rests atop a spher- ical air-bearing device which allows for nearly frictionless rotation in all three axes. The orientation of the platform is controlled by four reaction wheels arranged in a pyramidal configuration. Over the past few years, there have been significant updates to the reaction wheel subsystem, as well as requests for a more capable central com- puter. Therefore, a new system architecture for the …

Reproducing And Evaluating Charger Surfing: Robustness Of Smartphone Charging-Line Side-Channels, Colby M. Watts

Master's Theses

Smartphones are frequently connected to external, untrusted charging hardware, creating opportunities for side-channel attacks that do not require malware or direct access to device data. Charger Surfing, a recently proposed charging-line power analysis side-channel attack, reported high accuracy in inferring touchscreen input from voltage measurements collected from a smartphone’s charging cable; however, the reproducibility and robustness of these results under different conditions remain unclear. This thesis presents an independent replication and evaluation of Charger Surfing, including the development of an end-to-end data collection pipeline consisting of a modified charging cable, oscilloscope-based recordings, custom Android app, automated trace processing, and convolutional …

Autonomous Vision-Based Litter Collection Rover, Dante Michael Benedetti, Benjamin Scott Tavares, Nathan Heil

Electrical Engineering

This report documents the design, implementation, and testing of an autonomous litter-collection rover developed as a Senior Project Design Lab (EE 460/463/464) at California Polytechnic State University. The rover integrates autonomy, computer vision, embedded real-time control, mecanum-wheel omnidirectional mobility, and a two-degree-of-freedom robotic arm to detect, approach, and collect small ground-level litter such as bottles, wrappers, and paper fragments.

The system uses a two-layer compute architecture: an NVIDIA Jetson Orin Nano running ROS 2 for perception, SLAM, and path planning, paired with an STM32L4A6ZG microcontroller for real-time motor control and odometry. The robot is built on a multi-level aluminum frame …

Polysaber: A Custom Reactive Lightsaber Soundboard, Pedro B. Medeiros

Computer Engineering

The PolySaber project was developed as a custom reactive lightsaber control system built as a fully custom PCB design. The purpose of the project was to create a lower-cost and more customizable alternative to commercially available lightsaber soundboards while simultaneously providing hands-on experience in PCB design, embedded systems development, and hardware integration. Commercial lightsaber soundboards are expensive, proprietary, and difficult for hobbyists to customize. The PolySaber project addresses this by creating a modifiable hardware platform built around the ESP32 microcontroller. The system supports programmable firmware, RGB NeoPixel blade control, motion sensing, reactive swing and clash effects, onboard audio amplification, and …

Lora Networking Hardware Reference Designs For Terrestrial And Low-Earth-Orbit Communications, Kevin Nottberg

Master's Theses

The work presented here demonstrates a highly robust and tested LoRa networking hardware reference design to meet the needs of the embedded networking company OWL Integrations. The hardware presented integrated a unique combination of features and design choices. The detailing of its unique design is potentially of use to others for use in fielded battery powered terrestrial sensor networking hardware utilizing LoRa. Also, the terrestrial hardware presented is shown to have the capability to support command and control (C2) LoRa links in low-earth orbit beyond terrestrial systems. The design presented has a more U.S. centric component bill-of-materials (BOM), with the …

Design And Parametric Study Of A Mems-Based Reservoir Computer For Reinforcement Learning, Andrew P. Carr

Master's Theses

Single-node reservoir computing (RC) is a hardware-efficient approach to machine learning, leveraging the dynamics of physical systems. In this work, two reinforcement learning algorithms, Q-learning and Proximal Policy Optimization (PPO), are applied to a simulated micro-electro-mechanical system (MEMS)-based reservoir computer to solve both discrete and continuous control tasks. MEMS-based reservoirs are low-power, compact, and their natural frequencies (kHz to MHz) pair well with real-time control loops. To explore the relationship between reservoir dynamics and learning performance, a parametric study is conducted on two reservoir hyperparameters, reservoir size and neuron separation, using CartPole-v1 and MountainCar-v0. The RC successfully learns multiple tasks …

Hpc Configuration And Automated System Administration, Matty Witt, Deep Singh, Christopher Imirian

College of Engineering Summer Undergraduate Research Program

With the exponential growth in the use of computing, there is a growing need for undergraduate students to enter the workforce with experience with more complicated computing architectures. The CFD research group in the Aerospace Engineering Department received an HPC system and related computing hardware through the Air Force Research Lab. This system consists of three components: (1) a cluster compute engine with 256 CPU cores, 3.2 TB of RAM, 4 Tesla A100 GPUs, and 200 Gbps InfiniBand network backplane; (2) a high performance storage platform with 540 TB of raw storage, 200 Gbps InfiniBand network, and BeeGFS parallel cluster …

Open Source Asic Design Curriculum, Francisco Wilken

Master's Theses

The ever-growing importance of Application-Specific Integrated Circuits (ASICs) in a high-compute world necessitates that college graduates entering the workforce are well prepared to design them. This thesis details the design of novel ASIC curriculum, using open source tools to teach at the undergraduate level. By moving to a higher level of abstraction than classical transistor-focused coursework, chip design material can be made accessible earlier in an undergraduate degree. Additionally, open source tools provide a powerful, free, and portable platform for students to create their own designs, solving assignments focused on industry readiness. Finally, this thesis studies the results and challenges …

Bonsai Merkle Tree Streams: Bulk Memory Verification Unit For Trusted Program Verification System, Richard J. Rios

Master's Theses

Today, all modern computing systems are undoubtedly vulnerable to numerous types of attacks that could be targeted toward any layer of the system from dedicated hardware to highly abstracted software. Unfortunately, many devices and systems naturally contain inadequately protected components or software modules that un- dermine their security as a whole. Additionally, security is heavily variable system to system, and has a huge dependence on adequate implementation and ongoing support from device and software manufacturers. To address these various security issues in a very general way, TrustGuard, a containment security system utilizing an external device called the Sentry that would …

Incorporation Of Gnss Technology For Water-Level Instruments, Armaan S. Oberai, Toma Grundler, Serena B. Lee, Stefan A. Talke

College of Engineering Summer Undergraduate Research Program

Our goal was to take an existing water-level measuring embedded system and upgrade the GNSS module for the purpose of getting the elevation of the device within an error of 1 cm. Main milestones for the project included deploying a successful field test at a known survey point, using software-based post processing to improve the GNSS solution point, and implementing robust hardware and software for the water-level embedded system such that it was easily scalable.

Electronic Note-String Detector, Gavin Garcia-Rossi, Tommy Smail

Electrical Engineering

As the virtual space has become a dominant part of everyone’s day-to-day lives, many normal face-to-face interactions and services have not yet been facilitated by adapting technology. One of these prevailing areas is music lessons. Over Zoom meetings, or other virtual platforms, it is tremendously challenging to teach students. These challenges include recognizing student mistakes audibly and visually, and being able to give confident feedback on the incorrect notes played by learning musicians. Without having to delve into improving the complex systems that would be required to improve audio, video, and connection quality of these connections, we have another solution …

Custom Led Dashboard Integration For The Cal Poly Racing Team, Josue Hernandez

Computer Engineering

The Custom LED Dashboard Integration was made for the Cal Poly Racing Team, specifically the BAJA division. The dashboard was made as a way to combat the current limitations endured from the past methods used to display critical information of the vehicle to the car. The display was made to combat issues of limited quantity of data being able to be displayed to the driver and its small readability was an issue, the display helped combat that by providing a greater quantity of data being able to be sent and displayed on the display and the information being displayed having …

Drones For Marine Science And Agriculture, David Caldera, Sai Murthy

College of Engineering Summer Undergraduate Research Program

Our research project was launched at Cal Poly in 2019 with the goal of assisting researchers at the CSULB Shark Lab in detecting sharks from aerial images. Under the guidance of Dr. Franz J. Kurfess, students trained an object detection algorithm using shark images and were able to achieve high rate of detection. Following this success, the team has constructed multiple drones and expanded their research to include applications in the fields of agriculture and ecology. This summer the goal is to use a iPhone 14 Pro in lieu of a traditional camera system for real-time object recognition. Object detection …

Phone Microwave, Khanh Kim Hoang, Emily Zhou

Computer Engineering

This project involves the installation of remote-control capabilities in an antique 1980s microwave, effectively turning the microwave into a “smart” device. While preserving the original functionality of the microwave, a combination of software and hardware components allows for remote microwave operations. The microwave can be remotely operated by calling the built-in number, and more advanced settings and options can be utilized by texting. The microwave is also secured against unauthorized use with the addition of a PIN code that is required to operate the device.

Barrier Knockdown Test Control System For The Cal Poly Kinesiology Department, Regina M. Chapuis

Computer Engineering

The goal of this project is to design and implement a new control system for the LEDs and buttons on an existing Barrier Knockdown setup in the Cal Poly Kinesiology department. The Barrier Knockdown test is a testing apparatus in which subjects knock down a series of mechanical barriers in one of three patterns. The computer system times their reaction and movement time, and the test as a whole provides students with data to study the phenomenon of Contextual Interference. This system was previously controlled by an old computer setup that ultimately crashed. This project recreates the logic and user …

Mars Prototype Rover Environmental Measurement System, James A. Renick

Computer Engineering

In my senior project, the problem I am trying to solve is how to efficiently design, create, and install an original library onto a Mars prototype rover operating system and to further use that library to integrate a new weather measurement sensor device into the rover system with the necessary software and hardware implementations. This is an important and highly valued problem as many aerospace and other engineering companies utilize rovers and other autonomous systems for important research, explorations, and reconnaissance missions and goals. In solving this problem, I utilized many resources that were available to me such as advisors, …

Therapeutic Mechanical Horse, Cade M. Liberty, Aleya Dolorfino, Peter Philips, Zuzanna Dominik, Luke Watts

Mechanical Engineering

Jack's Helping Hand and its hippotherapy participants required a device to serve as an alternative to a live horseback riding experience that could also increase the range of riders. This would provide more clients with equine-assisted therapy that has proven to better the lives of people with both physical and mental disabilities. Horses can be unpredictable, tall, and sometimes anxiety-inducing, especially for new riders. Our group’s aim was to develop a mechanical horse that will be able to reduce these issues for equine therapy centers and the riders they help. When a rider gets to practice sitting on the horse …

Smartphone Control Of Rc Cars, Weston R. Fitzgerald

Electrical Engineering

The smartphone-controlled RC (remote-controlled) car is an inexpensive remote-controlled car designed to be fast and portable. Instead of manufacturing, packaging, and shipping a separate controller, the remote control is implemented in a phone application, which saves time and money in both the design process and the manufacturing process. Utilizing the user’s smartphone is more cost-effective since mobile devices are a common recurrence, and packaging fewer devices results in overall better portability of the product.

This smartphone-controlled car is speedy and intuitive to learn for typical smartphone users. The user can change the car’s speed and direction wirelessly using their phone; …

Accelerating Graphics Rendering On Risc-V Gpus, Joshua Simpson

Master's Theses

Graphics Processing Units (GPUs) are commonly used to accelerate massively parallel workloads across a wide range of applications from machine learning to cryptocurrency mining. The original application for GPUs, however, was to accelerate graphics rendering which remains popular today through video gaming and video rendering. While GPUs began as fixed function hardware with minimal programmability, modern GPUs have adopted a design with many programmable cores and supporting fixed function hardware for rasterization, texture sampling, and render output tasks. This balance enables GPUs to be used for general purpose computing and still remain adept at graphics rendering. Previous work at the …

A Method For Monitoring Operating Equipment Effectiveness With The Internet Of Things And Big Data, Carl D. Hays Iii

Master's Theses

The purpose of this paper was to use the Overall Equipment Effectiveness productivity formula in plant manufacturing and convert it to measuring productivity for forklifts. Productivity for a forklift was defined as being available and picking up and moving containers at port locations in Seattle and Alaska. This research uses performance measures in plant manufacturing and applies them to mobile equipment in order to establish the most effective means of analyzing reliability and productivity. Using the Internet of Things to collect data on fifteen forklift trucks in three different locations, this data was then analyzed over a six-month period to …

Inventory Locating With Quuppa: The Design And Development Of A Real-Time Process Monitoring Web Application Solution, Dylan C. Moreland, Trevor J. Howell, John W. Takiff, Patrick S. Dillon, Theo E. Fritz, William K. Mcintyre

Industrial and Manufacturing Engineering

Viasat, Inc. requires precise inventory tracking at their production facility in San Diego, CA. Viasat has installed the Quuppa indoor real-time locating system (RTLS), which it uses to track the real-time position of high-value work-in-process items. In its current state, the system only displays in-the-moment location information, with no available functionality for storing historical data for review, analysis, or visualization. In addition, the data displayed is noisy and prone to significant random error. This paper provides an overview of RTLS methods and technologies, assesses alternative solutions to Viasat’s issue, demonstrates our RTLS integrated web app solution, analyzes its impact, and …

A Power System-Based Iot Network For Remote Sensing Applications, Dominic Gaiero

Master's Theses

Cities around the world are facing increasingly significant challenges, including rapid urbanization, resource management, and environmental threats. In California for example, wildfires present an ever-growing threat that gravely harms people, destroys communities, and causes billions of dollars in damages. The task of addressing these environmental threats and many other challenges is greatly aided with widespread data collection and real-time inference. However, as IoT networks scale and require more energy for near-data analytics, the IoT endpoints require more power and complexity, limiting their deployment. Additionally, deploying endpoints in remote locations creates further challenges with higher reliability and communication constraints. In this …

Otter Vector Extension, Alexis A. Peralta

Computer Engineering

This paper offers an implementation of a subset of the "RISC-V 'V' Vector Extension", v0.7.x. The "RISC-V 'V' Vector Extension" is the proposed vector instruction set for RISC-V open-source architecture. Vectors are inherently data-parallel, allowing for significant performance increases. Vectors have applications in fields such as cryptography, graphics, and machine learning. A vector processing unit was added to Cal Poly's RISC-V multi-cycle architecture, known as the OTTER. Computationally intensive programs running on the OTTER Vector Extension ran over three times faster when compared to the baseline multi-cycle implementation. Memory intensive applications saw similar performance increases.

High Speed, High Current Monitoring System, Nicolette Lila Ray

Electrical Engineering

Electronics testing requires lengthy data collection and analysis. Streamlining at least part of this process allows resource reallocation, and faster data processing. Verifying a signal’s efficiency is key specification for a component’s datasheet. This project focuses on streamlining data collection when measuring a device’s output current. It combines amplifier design and digital interfacing to perform monitor a device’s output current. A computer-enable interface displays a graphical output current representation. It ensures accurate, high speed, high current measurements while removing a person’s need to manually plot data after testing. A new testing method provides room for company and product growth with …

Wine Sampler, Lance L. Litten

Computer Engineering

Quality testing is an important part of the wine industry. Without proper quality control, thousands of dollars could be wasted on bottling and recalling hundreds of gallons of wine. Due to this, labs are set up that collect wine samples from the tanks in a wine production plant and test them. A big part of this testing is determining exactly what tanks need to be tested and what tanks are at risk. My project aims to help automate this task by collecting data from the tanks wirelessly and keeping track of simple indicators such as pH and temperature. Automating this …

Polyone Smartphone, Joshua Zalmanowitz, Chi Nguyen, Gerome Cacho, Chris Lim

Electrical Engineering

The Poly One Smartphone is a student designed smartphone built to explore the implementation of 5G, provide a hardware solution to ensure personal information security and privacy, and provide longer battery life. The key features of this smartphone include but are not limited to a main cpu, some form of network connectivity in the form of Wi-fi or Cellular Data, calling functionality, a rechargeable battery that works with common power connection protocols, and compatibility with popular applications.

The Characterization Of Effective Electromagnetic Fields On The Safety And Quality Of Low-Moisture Foods (Effs) - Prototype Device Development, Joe G. Sandoval

Electrical Engineering

Contamination of low-moisture foods including flour, wheat grain, baby formula, and more, have increasingly become a concern due to sanitizing challenges. While industrial food processors have long used RF heating to sanitize mass quantities, an equivalent consumer device is absent from the market today. The Characterization of Effective Electromagnetic Fields on the Safety and Quality of Low-Moisture Foods (EEFS) project is an interdisciplinary effort to develop an RF heating consumer device to sanitize low-moisture foods.

A prototype device was designed to sanitize low-moisture food items using RF heating acceptable for commercial or consumer applications.

Room Management Web Application And Movement And Temperature Sensors, Visalbotr Chan, Huy Anh Duong

Computer Engineering

There are three main parts of this system: micro-controller, database, and website. Micro-controller detects motion of people walking in and out and It also measures room temperature and humidity in a confined space then updates collected data to the database. Our system’s database contains 6 main columns: room number, room capacity, number of students, temperature in Celsius, humidity in percent and date created. Finally, this database is queried by the website to display the information on the webpage. Users could also navigate on our site to check the most and least occupy rooms, and they can also search for a …

Tiny Disco: A Cost-Effective, High-Fidelity Wireless Audio System, Luke Martin Liberatore

Computer Engineering

The Tiny Disco is a WiFi based concert system, featuring improvements on popular “Silent Disco” concerts. Rather than being tied to compression and bandwidth restrictions present in traditional silent disco systems, the Tiny Disco system can deliver 320kbps+ audio quality, and allows listeners to bring their own headphones, further lending to the high quality audio experience.

Tiny Disco uses a Raspberry Pi as the audio server, and Espressif ESP32 microcontrollers as audio receivers/clients. The Tiny Disco is primarily geared toward smaller concerts and niche events where audio quality is valued, though due to its WiFi-based architecture, it can be expanded …