Computer Engineering Commons^™

A Review Of Polymer – Particles Composite Materials, Ismail Ibrahim Marhoon, Ayad Abbood Abdul Al-Hassan, Mohammed Ali Abdulrehman

Al-Esraa University College Journal for Engineering Sciences

In several engineering applications traditional materials are replacedby composite materials. Filled composite materials consist of the continuousmatrix and the filling particles. The primary purpose of introducing inorganicsolid particles into polymers is to essentially increase mechanical and physicalproperties. The wear properties of polymer composite can be changed to agreater degree by modifying the process of preparing the filled compositematerials. In the present review, a large-scale research has been conductedon the effect of wear on the composites of polymers. The effect of filler onthe polymer composites wear behavior has been thoroughly explained

Ability Of Replacing The Steel Strands By Cfrp In Pre-Stressed Concrete Girders: Art Review, Ahmed Salim Edan, Wael Shawky Abdulsahib

Al-Esraa University College Journal for Engineering Sciences

Fiber-reinforced polymer (FRP) composites are the modern,trustworthy alternatives to steel tendons and rebars. The bulk of currentresearch is devoted to establishing the feasibility of incorporating carbonfibre-reinforced polymer (CFRP) into reinforced concrete girders byevaluating the strength and reliability of CFRP and concrete components.In order to improve fatigue and corrosion resistance, CFRPs are crucial.Comparing reinforced prestressed concrete bridge girders strengthenedwith conventional steel reinforcement to those reinforced with CFRPs offersthe possibility of greatly increasing service life. Also widely researchedand used in bridge engineering as a corrosion-resistant substitute for steelreinforcement is CFRP composite material. The use of carbon fiber-reinforcedplastic (CFRP) reinforcement for prestressing concrete …

A Review Article On The Performance Based Seismic Design Of Structures, Reem Hatem Ahmed, Sahar Elaiwi, Shelan Hameed Ameen

Al-Esraa University College Journal for Engineering Sciences

For the most part, seismic design builds complex structural systems using the same small number of essential structural components as non-seismic design projects. Based on the building regulations, structures are frequently designed to "withstand" the largest earthquake with a given likelihood that is projected to happen at their location. This means that by avoiding structures from collapsing, the number of fatalities must be maintained to a minimal. Seismic design involves knowing the many failure modes regarding a structure and giving it the right stiffness, strength, ductility, and layout for ensuring that these modes do not take place. In this essay, …

2023 (Fall) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the fall of 2023.

Modeling The Moisture Content And Drying Rate Of Zucchini (Cucurbita Pepo L.) In A Solar Hybrid Dryer Using Ann And Anfis Methods, Halil Nusret Bulus, Aytac Moralar, Soner Celen

The Philippine Agricultural Scientist

Estimating product drying kinetics is critical to obtain the best drying process without compromising product quality and necessitates the development of numerical drying models. This research aims to compare the prediction models developed using artificial neural network (ANN) and adaptive network-based fuzzy inference system (ANFIS), two popular machine learning approaches in the recent years. Zucchini slices were chosen as samples and dried in a solar-assisted microwave belt dryer at 0.245 m/min belt speed and microwave powers of 0.7, 1, and 1.4 kW. On the data set obtained by computing the moisture content and drying rate values, prediction models were developed …

Challenges In Optimization For The Performance On Sustainability Dimensions In Reverse Logistics Social Responsibility, Sumarsono Sudarto, Katsuhiko Takahashi, Mochammad Dewo

Makara Journal of Technology

Reverse logistics social responsibility is preferred as the most acceptable solution for addressing the challenges in stakeholders’ debate regarding social responsibility in supply chains because it involves as many actors as possible in the supply chain to perform social responsibility to achieve sustainability. This paper explores the challenges in achieving optimal policies in sustainability dimensions for collection and recycling facilities in reverse logistics. Sustainability dimensions include economic, environmental, and social aspects. The reverse logistics is modeled on System Dynamics, and a simplified statistical analysis using a contour chart is employed in numerical experiments. Results show a narrow area of optimal …

Data-Driven Predictive Modeling To Enhance Search Efficiency Of Glowworm-Inspired Robotic Swarms In Multiple Emission Source Localization Tasks, Payal Nandi

Mechanical & Aerospace Engineering Theses & Dissertations

In time-sensitive search and rescue applications, a team of multiple mobile robots broadens the scope of operational capabilities. Scaling multi-robot systems (< 10 agents) to larger robot teams (10 – 100 agents) using centralized coordination schemes becomes computationally intractable during runtime. One solution to this problem is inspired by swarm intelligence principles found in nature, offering the benefits of decentralized control, fault tolerance to individual failures, and self-organizing adaptability. Glowworm swarm optimization (GSO) is unique among swarm-based algorithms as it simultaneously focuses on searching for multiple targets. This thesis presents GPR-GSO—a modification to the GSO algorithm that incorporates Gaussian Process Regression (GPR) based data-driven predictive modeling—to improve the search efficiency of robotic swarms in multiple emission source localization tasks. The problem formulation and methods are presented, followed by numerical simulations to illustrate the working of the algorithm. Results from a comparative analysis show that the GPR-GSO algorithm exceeds the performance of the benchmark GSO algorithm on evaluation metrics of swarm size, search completion time, and travel distance.

Accurate Orientation Control Of Tendon Driven Continuum Robots That Exhibit Elasticity, Manu Srivastava

All Dissertations

This dissertation makes new contributions to the modeling and implementation of Tendon Driven Continuum Robots (TDCRs). Specifically, motivated by 3D printing of concrete using a continuum hose robot in construction applications, we focus on TDCRs featuring compliance in the robot backbone and actuating tendons, e.g. surgical robots/endoscopes/catheters with tendon actuation. We expand previous mechanics-based models to show how and why such compliance significantly restricts performance when traditional kinematics-based planning and control techniques are applied.

The main contribution of this work is a new Elasticity Compensation(EC) model that explains why the ad hoc approach of preloading/pretensioning the tendons compensates for compliance …

The Potential Of The Implementation Of Offline Robotic Programming Into Automation-Related Pedagogy, Max Rios Carballo, Xavier Brown

Publications and Research

In this study, the offline programming tool RoboDK is used to program industrial robots for the automation sector. The study explores the feasibility of using this non-disruptive robot programming software for classroom use; assesses how well RoboDK can be used to program various robots used in the industry; creates and tests various applications; and pinpoints technical obstacles that prevent a smooth link between offline programming and actual robots. Initial results indicate that RoboDK is an effective tool for deploying its offline programming code to a Universal Robot, UR3e. There are many potential for advanced applications. The goal of the project …

A High-Speed Portable Ground Heat Exchanger Model For Use In Various Energy Simulation Software, Ryan Davies, Matt Mitchell, Edwin Lee

Macalester Journal of Physics and Astronomy

A portable component model (PCM) of a ground source heat pump system was developed and used as a test case in the creating of a PCM development framework. By developing this framework, new building energy simulation models will be able to be easily integrated into existing simulation software such as EnergyPlus and the Modelica Buildings Library. Our model uses a time responsive g-function and numerical methods to simulate ground source heat pumps for single time steps as well as long time scales. We validated our model against GHESim and GLHEPro and found that our model agrees with these two standards …

In-Situ Mechanical Tester, Andrrew Murach, Gustavo Marquez, Kosimo Tonn, Jake Vormbaum

Mechanical Engineering

Over the course of the 2022-23 Cal Poly SLO school year, a small tensile tester device was developed specifically for Dr. Long Wang to test thin film materials under a microscope and generate accurate force versus displacement graphs. A tensile tester was manufactured using purchased and machined components, electronics were consolidated in a separate box and connected, and a program and user interface were written to control the motion, provide custom inputs, and organize useful data for the researcher. Tests were conducted to compare the performance of the device to universal tensile testers available in the Composites lab. The device …

Assistive Robotic Platform For Non‐Urgent Household Tasks: A New Design, Amanda Serger, Normandy Tanguilan, Hakki Erhan Sevil

Florida Conference on Recent Advances in Robotics

Humans overcome minor household inconveniences daily without fully recognizing how challenging these tasks could be for individuals such as elderly people or people with disabilities. Those people often times struggle to complete tasks, for instance opening a door or reaching for an item, leading them to rely on caregivers for help. During the COVID-19 pandemic, this caregiver support becomes an unsafe and unreliable solution that can result in a greater risk, thus the need for another solution arises: robotic technology. Recent developments in the robotics field have paved the way for this research, aiming to design a home assistance robot …

Roboretrieve--In A Dual Role As A Hand-Held Surgical Robot And A Collaborative Robot End-Effector To Perform Spillage-Free Specimen Retrieval In Laparoscopy, Siqin Dong

Mechanical & Aerospace Engineering Theses & Dissertations

Recent advances in surgical robotics attempt to overcome limitations of manual surgery by augmenting the surgeon’s capabilities while performing suturing, incision, retraction, and retrieval tasks. This dissertation presents novel approaches for spillage-free specimen retrieval in confined spaces, targeted toward the surgical domain of minimally invasive robotic surgery. The retrieval task involves extraction of a resected specimen, residing in the abdominal cavity, completely outside of the patient’s body. A major challenge in this context is the spillage of content being retrieved, which may cause dissemination of malignancy. To address this challenge, this dissertation develops RoboRetrieve, a portable hand-held robot that …

2023 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2023.

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Deep Reinforcement Learning And Game Theoretic Monte Carlo Decision Process For Safe And Efficient Lane Change Maneuver And Speed Management, Shahab Karimi

All Dissertations

Predicting the states of the surrounding traffic is one of the major problems in automated driving. Maneuvers such as lane change, merge, and exit management could pose challenges in the absence of intervehicular communication and can benefit from driver behavior prediction. Predicting the motion of surrounding vehicles and trajectory planning need to be computationally efficient for real-time implementation. This dissertation presents a decision process model for real-time automated lane change and speed management in highway and urban traffic. In lane change and merge maneuvers, it is important to know how neighboring vehicles will act in the imminent future. Human driver …

Motion Control Simulation Of A Hexapod Robot, Weishu Zhan

Dartmouth College Master’s Theses

This thesis addresses hexapod robot motion control. Insect morphology and locomotion patterns inform the design of a robotic model, and motion control is achieved via trajectory planning and bio-inspired principles. Additionally, deep learning and multi-agent reinforcement learning are employed to train the robot motion control strategy with leg coordination achieves using a multi-agent deep reinforcement learning framework. The thesis makes the following contributions:

First, research on legged robots is synthesized, with a focus on hexapod robot motion control. Insect anatomy analysis informs the hexagonal robot body and three-joint single robotic leg design, which is assembled using SolidWorks. Different gaits are …

Implementation Of Static Rfid Landmarks In Slam For Planogram Compliance, Brennan L. Drake

Honors College Theses

Autonomous robotic systems are becoming increasingly prevalent in everyday life and exhibit robust solutions in a wide range of applications. They face many obstacles with the foremost of which being SLAM, or Simultaneous Localization and Mapping, that encompasses both creation of the map of an unknown environment and localization of the robot in said environment. In this experiment, researchers propose the use of RFID tags in a semi-dynamic commercial environment to provide concrete landmarks for localization and mapping in pursuit of increased locational certainty. With this obtained, the ultimate goal of the research is to construct a robotics platform for …

Beirut Arab University - Faculty Of Engineering - Newsletter Issue 0, Faculty Of Engineering, Beirut Arab University

Engineering Newsletters

No abstract provided.

Reactive Particle Swarm Control Architecture And Application For Scalar Field Adaptive Navigation, Shae Taylor Hart

Engineering Ph.D. Theses

Adaptive navigation is a subcategory of navigation techniques that attempts to identify goal locations that satisfy specific criteria in an unknown area. In 2D scalar field adaptive navigation (SFAN), primitives navigate to or along features of interest in an unknown, possibly time-varying, planar scalar field. Features include extrema, contours, and fronts. This work solves the 2D SFAN problem using swarm robotic techniques. Robotic swarms are a subset of multi-robot systems that use decentralized control of simple interchangeable robots to perform collective actions. A subgroup of swarms is the Reactive Particle Swarm (RPS), characterized based on its simplicity, reactivity to its …

Nautilus Rov Robot Manipulator, Dana Stefanides, Jenny Huynh, Andrew Stewart, Steven Reimer, Andrew Nguyen, Rebecca Walters, Matt Hayes

Interdisciplinary Design Senior Theses

Global warming and climate change are prevalent issues in today’s society. As a result, research in the ocean, our world’s biggest ecosystem, is imperative in efforts to protect the environment. Santa Clara University’s Robotic Systems Lab contributes to this field through work and developments on remotely operated vehicles (ROVs). An existing ROV system called Nautilus consists of a robot arm, end effector, and storage system in order to collect various types of sediments at a depth of 300 feet. However, the previous system does not meet that requirement. In direct collaboration with researchers within the Monterey Bay Aquarium Research Institute, …

Assessing High Dynamic Range Imagery Performance For Object Detection In Maritime Environments, Erasmo Landaeta

Doctoral Dissertations and Master's Theses

The field of autonomous robotics has benefited from the implementation of convolutional neural networks in vision-based situational awareness. These strategies help identify surface obstacles and nearby vessels. This study proposes the introduction of high dynamic range cameras on autonomous surface vessels because these cameras capture images at different levels of exposure revealing more detail than fixed exposure cameras. To see if this introduction will be beneficial for autonomous vessels this research will create a dataset of labeled high dynamic range images and single exposure images, then train object detection networks with these datasets to compare the performance of these networks. …

Neural Network Fusion Of Multi-Modal Sensor Data For Autonomous Surface Vessels, David J. Thompson

Doctoral Dissertations and Master's Theses

Autonomous surface vessels (ASV) can potentially improve the safety of vessels traditionally operated by humans. Despite advancements in autonomous on-road vehicles, many of these advancements have yet to be realized for ASVs. This is primarily due to lacking ASV sensing platforms and public datasets for ASV-based perception research. To that end, this dissertation demonstrates the design of a synchronized multi-modal sensing platform for ASVs utilizing GPS/INS, LiDAR, LWIR cameras, HDR camera, and high-resolution cameras. The sensing platform is designed to maximize the overlap of sensors for multi-modal research and provides accurate intrinsic and extrinsic calibration between each sensor. Furthermore, the …

Molecular And Cellular Level Characterization Of Cytoskeletal Mechanics Using A Quartz Crystal Microbalance, Emily M. Kerivan, Lyle Tobin, Mihir Basil, Dana N. Reinemann

Faculty and Student Publications

A quartz crystal microbalance (QCM) is an instrument that has the ability to measure nanogram-level changes in mass on a quartz sensor and is traditionally used to probe surface interactions and assembly kinetics of synthetic systems. The addition of dissipation monitoring (QCM-D) facilitates the study of viscoelastic systems, such as those relevant to molecular and cellular mechanics. Due to real-time recording of frequency and dissipation changes and single protein-level precision, the QCM-D is effective in interrogating the viscoelastic properties of cell surfaces and in vitro cellular components. However, few studies focus on the application of this instrument to cytoskeletal systems, …

Gesture-Based American Sign Language (Asl) Translation System, Kayleigh Moore, Stefano Pecile, Mahdi Yazdanpour

Posters-at-the-Capitol

According to the World Health Organization (WHO), over 5% of the world's population experiences severe hearing loss. Approximately 9 million people in the U.S. are either functionally deaf or have mild-to-severe hearing loss. In this research, we designed and implemented a translation interface which turns American Sign Language (ASL) gestures captured from a pair of soft robotic gloves into text and speech instantaneously.

We used a combination of flex sensors, tactile sensors, and accelerometers to recognize hand gestures and to record hand and fingers positions, movements, and orientations. The digitized captured gestures were then sent to our proposed translation interface …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

College of Graduate Studies: Theses & Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

Space Force Design Project, Emily Greene, Ashton Orosa, Julia Patek, Nathan Doty

Williams Honors College, Honors Research Projects

The objective of our research project is to develop a lab testbed composed of a curved surface to represent a spacecraft hull, a mobile robot equipped with repair tools, and a robotic arm equipped with a laser 3D scanner. This project is part of a larger grant to the University of Akron from Space Force and Air Research Labs. The lab testbed developed in this project will be used to assist in creating and testing a software and algorithm to inspect and repair spacecraft while in orbit. The project will involve researching spacecraft hulls to create an accurate simulation bed, …

Enhancing Traffic Safety In Unpredicted Environments With Integration Of Adas Features With Sensor Fusion In Intelligent Electric Vehicle Platform With Implementation Of Environmental Mapping Technology, David S. Obando Ortegon

College of Graduate Studies: Theses & Dissertations

A major objective on society is to reduce the number of accidents and fatalities on the road for drivers, and pedestrians. Therefore, the automotive engineering field is working on this problem through the development and integration of safety technologies such as advanced driving assistance systems. For this reason, this work was intended to develop and evaluate the performance of different ADAS features and IV technologies under unexpected scenarios. This by the development of safety algorithms applied to the intelligent electric vehicle designed and built in this work, through the use of ADAS sensors based on sensor fusion. Evaluation of AEB, …

Imitation Learning For Swarm Control Using Variational Inference, Hafeez Olafisayo Jimoh

Graduate Theses, Dissertations, and Problem Reports (ETD)

Swarms are groups of robots that can coordinate, cooperate, and communicate to achieve tasks that may be impossible for a single robot. These systems exhibit complex dynamical behavior, similar to those observed in physics, neuroscience, finance, biology, social and communication networks, etc. For instance, in Biology, schools of fish, swarm of bacteria, colony of termites exhibit flocking behavior to achieve simple and complex tasks. Modeling the dynamics of flocking in animals is challenging as we usually do not have full knowledge of the dynamics of the system and how individual agent interact. The environment of swarms is also very noisy …

A Semantic Web Approach To Fault Tolerant Autonomous Manufacturing, Fadi El Kalach, Ruwan Wickramarachchi, Ramy Harik, Amit Sheth

Publications

The next phase of manufacturing is centered on making the switch from traditional automated to autonomous systems. Future factories are required to be agile, allowing for more customized production, and resistance to disturbances. Such production lines would be able to reallocate resources as needed and minimize downtime while keeping up with market demands. These systems must be capable of complex decision-making based on parameters such as machine status, sensory/IoT data, and inspection results. Current manufacturing lines lack this complex capability and instead focus on low-level decision-making on the machine level without utilizing the generated data to its full extent. This …