Computer Engineering Commons^™

The Role Of Si3n4 Amorphous Phase In Nc-Tin/A-Si3n4 Nanocomposites In Increases The Hardness And Thermal Stability, Keba Moto

Makara Journal of Technology

The role of Si3N4 amorphous phase in nc-TiN/a-Si3N4 nanocomposites will be shown and compared with polycrystalline ZrN/Ni which has no such amorphous phase (non-composites). The presence of amorphous phase Si3N4 increases the hardness of film as well as the toughness of the bulk nanocomposites under indentation load. It has been observed that nc-TiN/a-Si3N4 nanocomposites films has higher thermal stability than ZrN/Ni polycrystalline films.

Biodiesel's Characteristics Preparation From Palm Oil, Tilani Hamid. S, Rachman Yusuf

Makara Journal of Technology

Biodiesel’s characteristics preparation from palm oil. Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester) by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH) as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio …

Development Of Hardness Measurement Procedure For Nanocomposite Nc-Tin/A-Si3n4, Keba Moto

Makara Journal of Technology

Hardness of nc-TiN/a-Si3N4 nanocomposites which was determined by using two methods of measurements i. e. depth sensing method and remaining plastic indentation area that were magnified by using SEM (Scanning Electron Microscope) lie in the good agreement. The hardness value is not influenced by the biaxial and residual compressive stress. The measurement of the biaxial stress on the substrate shows a very small value of biaxial stress as well as the constant hardness and crystallite size against annealing temperature. Therefore, the reported hardness value here is the intrinsic value that depend on its microstructure properties.

Integrating Passenger And Modulo As Learning Tools For Collaborative Engineering Education, Kalamullah Ramli, Frank Schwarz, Stefan Werner, A Halim Shamsuddin, Axel Hunger

Makara Journal of Technology

The University of Indonesia (UI), Gerhard Mercator University (GMU), the Universiti Kebangsaan Malaysia (UKM) have agreed to cooperate as partners to develop a joint bachelor (3+1) and masters (1+1) degree, and collaborate in the research fi elds of multimedia- and internet-based learning and application level active networks. This paper describes the introduction of the Offshore Project and the extending of information technology applications to the partner institutions in this international cooperation which would very much enhance the operations of the new initiative in engineering education, which could provide students in far distance with more fl exible learning environment.

Study Effect Of Salt Washing Process On Content And Iodium Stability Of Salt, Nelson Saksono

Makara Journal of Technology

Effect of Salt Washing Process on Content and Iodium Stability of Salt. Salt washing process should increase the salt quality. It should clean the salt from sludge or clay and also reduce the impurity compound such as Mg, Ca and the reductor content. The objective of these reseach is to assess the effect of washing process on the content og hygroscopic impurities compound (Ca and Mg), and reductor content of salt. The research also investigate the water absorbing, pH, KIO3 content as function of time to obtain effect of washing process on KIO3 stability in salt. The experiment result shows …

Object Classfification In Computer Vision With Discriminant Analysis, Amir Hamzahan

Makara Journal of Technology

A robotic sensor system is always supported by a computer system called ‘computer vision’. The important concept of computer vision is object classfifi cation. In this study two algorithms for object classifi cation in this system will be compared. Firstly, A simple method that do not need complex computation and that considered as an informal method is called binary tree decision structure. This method is based on modest caracteristic decriptors of an object such as vertical line, horizontal line or ellipse line. Unfortunately this method has weakness in recognize an image that contaminated by a noise. Secondly, a more formal …

Making Alloys (Ti1 - Xalx) N Using Plasma Cvd Technique From Alcl3 Powder, H2 And N2 Gas ,With Solvent Ticl4, Keba Moto

Makara Journal of Technology

The substitution of Ti atoms by Al atoms in TiN lattice sites to form (Ti1-xAlx)N is clearly demonstrated by the coatings which were deposited on steel substrate and using plasma CVD technique. The presence of Al atoms in TiN lattice site is shown by means of XRD and EDX techniques: lattice parameters decreasing of TiN as the fraction of Al increases (XRD) and precipitation of hexagonal AlN phase (XRD) as the fraction of Al exceeding 0.8 (EDX). The hardness of these coating are just around 30 GPa, which is beyond the values reported in literatures.

Effects Of 0.25 % Mo (Molybdenum) Which Is Contained In The Ductile Cast Iron On Mechanical Properties Of Austempered Ductile Iron (Adi)., Nukman Nukman, Bustanul Arifin, Bambang Sugiarto

Makara Journal of Technology

The aim of this research is to investigate the effects of 0.25 % Mo (Molybdenum) which is contained in the ductile cast iron on mechanical properties of Austempered Ductile Iron (ADI). The various temperatures and the holding times are used in the heat treatment processes. Using a given 0.25 % Mo in the ductile iron, ADI's alloyed developes a higher ultimate tensile stress value and decreases the elongation if we compare with the as cast (non alloy ductile iron). The higher impact energy value obtained at 9000 C austenization and 375o C austempering temperatures during 60 minutes holding times. The …

The Manufacturing Properties Of Galvanised Steel Sheet With Hexagonal And Tetragonal Network Of Circle Holes, Rahmat Saptono

Makara Journal of Technology

Galvanized steel sheet of 0.8 mm in thickness was drilled with circle holes of 2.5 mm diameter and spacing arranged in tetragonal and hexagonal pattern. The manufacturing properties of specimen were studied through drawing and stretching simulative test. It was concluded from the results that, at high ratio of punch to hole diameter (40/2.5), the drawing properties (LDR) of both square and hexagonal perforated sheet were slightly lower than that of solid sheet, while hexagonal perforated showing LDR somewhat higher than the square one. The stretching properties (LDH) of sheet, however, were much lower than that of solid sheet while …

Develops The Software Of Dsp Processor For The Cdma Circuitry, Arman Djohan D.

Makara Journal of Technology

This research develops the software of DSP Processor type TMS320C54X for the CDMA circuitry. This research apply two algorithms namely Mathematic Algorithm and table lookup Algorithm. From both algorithms, the research examine what algorithm have the fasted processing time and the smallest memory occupation. From the examination results the Mathematic Algorithm have 20.62 milliseconds processing time and the Table lookup algorithm have 14.08 milliseconds processing time. The Table lookup algorithm have the fastest processing time because the Matematic algorithm need the rounding process of the fi gure. Eventhough such processing time is not exceed from the 125 millisecond of delay …

2002 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2002.

2001 (Fall) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the fall of 2001.

Comparison Of Two Distributed Fuzzy Logic Controllers For Flexible-Link Manipulators, Linda Z. Shi, Mohamed Trabia

Mechanical Engineering Faculty Presentations

The paper suggests that fuzzy logic controllers present a computationally efficient and robust alternative to conventional controllers. The paper presents two possible structures for the distributed fuzzy logic controller of a single-link flexible manipulator. A linear quadratic regulator method is used to prove the effectiveness of fuzzy logic controllers.

Process Flow Optimization Studies Through Discrete Event Simulation, Milind Chokshi

Electrical & Computer Engineering Theses & Dissertations

Computer-aided simulation has begun to emerge as a powerful tool for numerical analysis of the behavior and anticipated performance of industrial systems and their optimization. Applications include materials handling, storage and controls systems, prediction of manufacturing efficiencies, and production optimization. Simulations are used to test baseline models and subsequently analyze new production concepts, operating strategies, and planned procedures prior to costly implementation.

The study of process flows in a manufacturing environment is difficult due to its inherent stochastic nature. Breakdown of the sub-systems and failures of machines is a random process and needs to be solved based on concepts of …

Application Of Wavelets And Principal Component Analysis In Image Query And Mammography, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

Breast cancer is currently one of the major causes of death for women in the U.S. Mammography is currently the most effective method for detection of breast cancer and early detection has proven to be an efficient tool to reduce the number of deaths. Mammography is the most demanding of all clinical imaging applications as it requires high contrast, high signal to noise ratio and resolution with minimal x-radiation. According to studies [36], 10% to 30% of women having breast cancer and undergoing mammography, have negative mammograms, i.e. are misdiagnosed. Furthermore, only 20%-40% of the women who undergo biopsy, have …

1999 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 1999.

Combining Wavelets And Hotelling Transforms In Image Query, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

In the "content based" image query, also referred to as "query by example," "similarity retrieval" or "sketch retrieval," the query image is provided by the user either as a sketch of the object, as the output of a scanner or a video camera. Some of the difficulties associated with content based image query are described in [1], e.g. significant difference between the "query image" and the "target image," artifacts and poor resolution of the query image make a straightforward comparison of images using L1 and l2 metrics not effective.

In [2] a new strategy is suggested based on wavelet decomposition …

Robust Course-Boundary Extraction Algorithms For Autonomous Vehicles, Chris Roman, Charles Reinholtz

Graduate School of Oceanography Faculty Publications

Practical autonomous robotic vehicles require dependable methods for accurately identifying course or roadway boundaries. The authors have developed a method to reliably extract the boundary line using simple dynamic thresholding, noise filtering, and blob removal. This article describes their efforts to apply this procedure in developing an autonomous vehicle.

Arts, Computers And Artificial Intelligence, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

Science and art seem to belong to different cultures. Science and technology, mainly the products of the intellect, use terminology and vocabulary that are concise and well defined. In contrast, in artistic expression, ambiguity is a powerful component. Still the relationship between these two different categories of human activity is interesting and fascinating. In this paper, a general comparison of these two disciplines will be introduced. Then the possibility of mechanical creation of art using computers and artificial intelligence will be discussed. This will be followed by two techniques which are used to create poetry and music. First, a statistical …

Incorporating Matlab's Signal Processing Toolbox Into A Dsp Course At An Undergraduate E.E. Program, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

This paper provides some suggestions for incorporating MATLAB's Signal Processing Toolbox into a DSP course. Often, in a DSP course, students have difficulties understanding abstract and non-intuitive concepts and seeing their relevance to the practical part of their curriculum. The tools offered by MATLAB's Signal Processing Toolbox, can help to make these concepts more tangible and provide a perspective for students. Some basic tools relevant to an undergraduate DSP course will be introduced, including examples of tool use and graphic results. The tools presented will be applied in the areas of synthesis and analysis of signals, FFT computation, impulse response …

Using Matlab To Illustrate The 'Phenomenon Of Aliasing', Sol Neeman, Ph.D.

Engineering Studies Faculty Publications and Creative Works

The phenomenon of aliasing is important when sampling analog signals. In cases where the signal is bandlimited, one can avoid aliasing by ensuring that the sampling rate is higher than the Nyquist rate . But in cases where the signal is not bandlimited , aliasing is unavoidable if the signal is not filtered before it is sampled. It is then crucial to understand the phenomenon in order to estimate the distortion generated when the signal is reconstructed from its samples. Using the software package MATLAB by MathWorks, Inc ., two examples are presented. The first is a pure sinusoid which …

Msda A Machinery Selection Decision Aid For Stubble Management Practices, Linda Leonard, Andrew Green

Grain and other field crops published reports

MSDA is a user friendly program developed to help farmers predict stubble outcomes before acting on their management practice. This manual is an accompaniment to a computer program designed on Micorsoft Excel-macros. Its aim is to help farmers assess their current machinery and stubble handling ability and view options that may be adopted as best practice for their properties.

The program is designed with the complete season in mind. Information is gathered on the full complement of machinery used from harvest through to seeding, to allow farmers to see all choices available and enable them to choose the best system …

Acoustic Correlates Of Vowel Perception As Determined From Synthesis Experiments With Multi-Tone Stimuli, Zhongjiang Zhang

Electrical & Computer Engineering Theses & Dissertations

An essential requirement of speech signal processing is to extract information (features or parameters) from the speech signal which encode the information carried by the signal. The objective of this thesis work was to examine and evaluate two feature sets as acoustic correlates for vowel perception. They are formants and DCTCs. Formants are the frequencies of spectral peaks of the speech signal. DCTCs are the Discrete Cosine Transform Coefficients of the magnitude spectrum and are thus features which encode the global spectral shape of speech signal.

There are different opinions regarding which feature set is a more accurate representation for …

Variable Structure End Point Control Of A Flexible Manipulator, Shailaja Chenumalla, Sahjendra N. Singh

Electrical & Computer Engineering Faculty Research

We treat the question of control and stabilization of the elastic multibody system developed in the Phillips Laboratory, Edwards Air Force Base, California. The controlled output is judiciously chosen such that the zero dynamics are stable or almost stable. A variable structure control (VSC) law is derived for the end point trajectory control. Although, the VSC law accomplishes precise end point tracking, elastic modes are excited during the maneuver of the arm. A Linear stabilizer is designed for the final capture of the terminal state.

Data Communication Between An Expert System Shell And A Conventional Algorithmic Program With Application To Cam Motion Specification, Paul P. Lin, An-Jen Yang

Mechanical Engineering Faculty Publications

Although more and more expert system shells have begun to provide communication interfaces to conventional procedural languages, the interfaces are basically shell- and language-dependent. This paper presents a simple, shell- and language-independent data communication technique between a shell and a procedural language via a concept analogous to the handshake data transmission used in microprocessors. A control file is used for the action of handshake. The communication interface is between two data files in two different language environments. A program written in a LISP-based expert system shell, OPS 5, and one written in a procedural language, FORTRAN, were …

Analog Computer Simulation With Automatic Scaling By Digital Computer, Mark Anthony Motter

Electrical & Computer Engineering Theses & Dissertations

A computer-aided design approach for the simplification of analog computer simulation is presented. The simulation configuration consists of an EAI 2000 analog computer with serial communications link to a PDP — 11/24 digital computer. Under control of the PDP-11, the analog simulations are realized with appropriate time and magnitude scaling which adjusts the range of the simulation coefficients and prevents overloads of the analog components. The analog computer hardware configuration accommodates both stable plants up to eighth order and closed-loop systems up to tenth order. Cascade compensation is provided for the closed-loop systems.

The plant may be described by either …

Some Facts And Prospects For The Establishment Of Television Broadcasts In Mainland Tanzania, H. R. Mgombelo

Tanzania Journal of Engineering and Technology (TJET)

Abstract