Transportation Engineering Commons^™

15-08 Community-Aware Charging Station Network Design For Electrified Vehicles In Urban Areas: Reducing Congestion, Emissions, Improving Accessibility, And Promoting Walking, Bicycling, And Use Of Public Transportation, Ratna Babu Chinnam, Alper E. Murat

Transportation Research Center Reports

A major challenge for achieving large-scale adoption of EVs is an accessible infrastructure for the communities. The societal benefits of large-scale adoption of EVs cannot be realized without adequate deployment of publicly accessible charging stations due to mutual dependence of EV sales and public infrastructure deployment. Such infrastructure deployment also presents a number of unique opportunities for promoting livability while helping to reduce the negative side-effects of transportation (e.g., congestion, emissions, and noise pollution). In this phase, we develop a modeling framework (MF) to consider various factors and their associated uncertainties for an optimal network design for electrified vehicles. The …

Optimization Of Headway, Stops, And Time Points Considering Stochastic Bus Arrivals, Liuhui Zhao

Dissertations

With the capability to transport a large number of passengers, public transit acts as an important role in congestion reduction and energy conservation. However, the quality of transit service, in terms of accessibility and reliability, significantly affects model choices of transit users. Unreliable service will cause extra wait time to passengers because of headway irregularity at stops, as well as extra recovery time built into schedule and additional cost to operators because of ineffective utilization of allocated resources.

This study aims to optimize service planning and improve reliability for a fixed bus route, yielding maximum operator’s profit. Three models are …

Study On Open-Packing Inspection Of Dangerous Goods Container At Shanghai Port, Guohua Li

Maritime Safety & Environment Management Dissertations (Dalian)

No abstract provided.

Improved Methodologies In Modeling And Predicting Failure In Aashto M-180 Guardrail Steel Using Finite Element Analysis – Phase I, Brandt M. Humphrey, Robert W. Bielenberg, Ronald K. Faller, John D. Reid, Mehrdad Negahban

Nebraska Department of Transportation: Research Reports

No abstract provided.

Midwest Guardrail System (Mgs) Placed Adjacent To A 1v:2h Fill Slope With 6-Ft Posts, Austin J. Haase, Justine E. Kohtz, Karla A. Lechtenberg, John D. Reid, Ronald K. Faller

Nebraska Department of Transportation: Research Reports

No abstract provided.

Modeling, Control, And Impact Analysis Of The Next Generation Transportation System, Feng Zhu

Open Access Dissertations

This dissertation aims to develop a systematic tool designated for connected and autonomous vehicles, integrating the simulation of traffic dynamics, traffic control strategies, and impact analysis at the network level.

The first part of the dissertation is devoted to the traffic flow modeling of connected vehicles. This task is the foundation step for transportation planning, optimized network design, efficient traffic control strategies, etc, of the next generation transportation system. Chapter 2 proposes a cell-based simulation approach to model the proactive driving behavior of connected vehicles. Firstly, a state variable of connected vehicle is introduced to track the trajectory of connected …

Improving The Laboratory Design Of Asphalt Mixtures To Enhance Asphalt Pavement Durability, Ali Hekmatfar

Open Access Dissertations

Most departments of transportation, including Indiana’s, currently use the Superpave mixture design method to design asphalt mixtures. This method specifies that the optimum asphalt content for a given gradation be selected at 4 percent air voids. During construction, these mixtures are typically compacted to 7-8 percent air voids. If mixtures were designed to be more compactable in the field they could be compacted to the same density as the laboratory mixture design, which would increase pavement durability by decreasing the in-place air voids. The objective of this research was to enhance the asphalt mixture design method in order to increase …

2016 Safety Belt Usage Survey In Kentucky, Kenneth R. Agent, Eric R. Green, Michael A. Fields

Kentucky Transportation Center Research Report

The use of safety belts and child safety seats is a proven means of reducing injuries to motor vehicle occupants involved in traffic crashes. There have been various methods used in efforts to increase safety belt and safety seat usage. Past efforts have included public information campaigns, local and statewide legislation, and enforcement of the legislation.

The objective of the survey summarized in this report was to establish a statewide safety belt usage rate in Kentucky for 2016. This rate can be compared to those determined from previous surveys. The 2016 statewide survey documents the continued increase in usage associated …

Miss Lonesome: Old Boats Past Their Prime, Garth Woodruff

Faculty Publications

No abstract provided.

Synthesis Of Kentucky’S Traveler Information Systems, Christopher W. Van Dyke, Jennifer R. Walton, James Ballinger

Kentucky Transportation Center Research Report

After the United States Department of Transportation (USDOT) petitioned the Federal Communications Commission (FCC) to establish a dedicated phone number for real-time travel information services, the abbreviated 511 dialing code was founded in July 2000. The FCC reasoned that 511 services could reduce traffic congestion, air pollution, and the inefficient use of fossil fuels. 511 would, in turn, improve traveler safety. In 2010, the Federal Highway Administration (FHWA) mandated a set of requirements for systems that deliver real-time traffic information to the public. States DOTs were asked to comply with this mandate by November 2014. Many states, in addition to …

Identifying And Addressing Soil Property Issues Affecting Roadside Vegetation Establishment, Xu Li, Martha Mamo, Walter H. Schacht, Tala Awada, Humberto Blanco-Canqui

Nebraska Department of Transportation: Research Reports

Attaining adequate vegetation cover along highways is important for NDOR to comply with EPA’s stormwater regulations. However, low plant cover is a common problem on shoulders (first 16 feet off the pavement) of many highways in Nebraska. The ultimate goal of this study is to identify cost-effective engineering solutions that assure adequate seed beds (i.e., soil conditions) for establishment of selected seeding mixtures. The objectives of this study are to (1) characterize the soil properties along roadsides where vegetation stands have not developed well, and (2) verify the effects of select soil property parameters on plant germination and establishment.

Sampling …

Robust Algorithms For Estimating Vehicle Movement From Motion Sensors Within Smartphones, Ilyas Ustun

Computational Modeling & Simulation Engineering Theses & Dissertations

Building sustainable traffic control solutions for urban streets (e.g., eco-friendly signal control) and highways requires effective and reliable sensing capabilities for monitoring traffic flow conditions so that both the temporal and spatial extents of congestion are observed. This would enable optimal control strategies to be implemented for maximizing efficiency and for minimizing the environmental impacts of traffic. Various types of traffic detection systems, such as inductive loops, radar, and cameras have been used for these purposes. However, these systems are limited, both in scope and in time. Using GPS as an alternative method is not always viable because of problems …

Utilizing Egocentric Video And Sensors To Conduct Naturalistic Bicycling Studies, Feng Liu, Miguel A. Figliozzi

TREC Final Reports

Existing data collection methods are mostly designed for videos captured by stationary cameras and are not designed to follow cyclists along a route or to integrate other sensor data. The goals of this research are: a) to develop a platform to collect naturalistic video bicycling data, b) to develop a methodology to integrate video data with other sensors that measure cyclists’ position and comfort levels, and c) to apply the platform and data collection methodology to a real-world route. This research effort has successfully integrated video and sensor data to describe cyclists’ comfort levels along a route. It was found …

Visualizations Of Travel Time Performance Based On Vehicle Re-Identification Data, Stanley E. Young, Elham Sharifi, Christopher M. Day, Darcy M. Bullock

Lyles School of Civil Engineering Faculty Publications

This paper provides a visual reference of the breadth of arterial performance phenomena based on travel time measures obtained from reidentification technology that has proliferated in the past 5 years. These graphical performance measures are revealed through overlay charts and statistical distribution as revealed through cumulative frequency diagrams (CFDs). With overlays of vehicle travel times from multiple days, dominant traffic patterns over a 24-h period are reinforced and reveal the traffic behavior induced primarily by the operation of traffic control at signalized intersections. A cumulative distribution function in the statistical literature provides a method for comparing traffic patterns from various …

Modeling Economic Impacts Of The Inland Waterway Transportation System, Furkan Oztanriseven

Graduate Theses and Dissertations

The inland waterway transportation system of the United States (U.S.) handles 11.7 billion tons of freight annually and connects the heartland of the U.S. with the rest of the world by providing a fuel-efficient and environmentally friendly mode of transportation. This dissertation aims to create decision support tools for maritime stakeholders to measure the economic impacts of the inland waterway transportation systems under real world scenarios including disruptions, demand changes, port expansion decisions, and channel deepening investments. Monte Carlo simulation, system dynamics, discrete-event simulation, agent-based modeling, and multiregional input-output modeling techniques are utilized to analyze the complex relationships between inland …

15-05 Infrastructure And Technology For Sustainable Livable Cities, Upul Attanayake, Mehedi Hasan, Lizmert Lopez

Transportation Research Center Reports

Providing access and mobility for key installations and businesses located in cities become a challenge when there is limited public transport and non-motorized facilities. The challenges are significant in cities that are subjected to severe winter weather conditions. Improving access to sustainable mobility choices is a key aspect of developing livable cities. This project scope is limited to identifying methods and infrastructure to promote walking and cycling. With regards to cycling, bike-share program development and use of location-allocation models as planning tools are presented. To minimize exposure to adverse weather conditions, underground and above ground pedestrian systems are provided. These …

Use Of Recycled Crushed Concrete (Rcc) Fines For Potential Soil Stabilization, Lindeman Mark, Varilek Brandon, Lieska Halsey, Rick Gloe, Maria Olomi

Nebraska Department of Transportation: Research Reports

This study evaluated the use of Recycled Crushed Concrete (RCC) Fines for potential soil stabilization. Soil stabilization is the enhancement of subgrade stability to improve the constructability of successive pavement layers. Use of RCC fines may not only provide less costly alternatives for subgrade stabilization, but their use may also alleviate landfill disposal challenges.

Development Of An Improved Method For Determining Advisory Speeds On Horizontal Curves, Eric R. Green, Kenneth R. Agent, Erin Lammers-Staats

Kentucky Transportation Center Research Report

Horizontal curves are an integral part of the highway alignment. However, a disproportionately high number of severe crashes occur on them. One method transportation agencies use to reduce the number crashes at horizontal curves is the installation of curve warning signs which post an appropriate advisory speed. Appropriate curve advisory speeds can be determined using several methods. Some of these methods are time-consuming to perform and are error-prone. The purpose of this research was to find the most efficient and accurate data collection method for determining curve advisory speeds. Several processes were developed and tested. They were then validated against …

Estimation Of Average Daily Traffic On Local Roads In Kentucky, Reginald R. Souleyrette, Brian K. Howell, Eric R. Green, William Nicholas Staats

Kentucky Transportation Center Research Report

Kentucky Transportation Cabinet (KYTC) officials use annual average daily traffic (AADT) to estimate intersection performance across the state maintained highway system. KYTC currently collects AADTs for state maintained roads but frequently lacks this information on local roads. A method is needed to estimate local road AADTs in a cost-effective and reasonable manner. Kentucky Transportation Center (KTC) researchers conducted a literature review on U.S. AADT models but found that none of them were suitable to Kentucky. Therefore, KTC developed an AADT model using non-linear regression to estimate AADTs on approaches to those intersections.

KTC developed a Poisson distributed, non-linear regression model …

Use Of Cycling Paths Along The Morogoro Brt Line, Ford Sanger

Independent Study Project (ISP) Collection

As the urban population continues to increase rapidly in Dar es Salaam it will become increasingly important to find sustainable means of urban transportation. With planned infrastructure improvements in the city to help alleviate traffic congestion, bicycles, which represent a largely underutilized form of urban transportation, have the potential to play a large role in the future of the city. Through background research, direct observations, community surveys, and interviews, both formal and informal, this study sought to understand the impact of the recent addition of bike lanes along the first phase of the Dar Bus Rapid Transit line. It was …

Methodologies For Estimating Traffic Flow On Freeways Using Probe Vehicle Trajectory Data, Khairul Azfi Anuar

Civil & Environmental Engineering Theses & Dissertations

Probe vehicle data are increasingly becoming the primary source of traffic data. As probe vehicle data become more widespread, it is imperative that methods are developed so that traffic state estimators such as flow, density, and speed can be derived from such data. In this dissertation three different methodologies are proposed for predicting traffic flow or volume on a freeway. All of the proposed methodologies exploit several different traffic flow theories in conjunction with probe vehicle data to predict traffic flow. The first methodology takes advantage of the fundamental diagram or speed-flow relationship. The relationship states that flow can be …

Development Of Visualization-Animation Software For Learning Transportation Algorithms, Ivan P. Makohon

Computational Modeling & Simulation Engineering Theses & Dissertations

Recognizing the steady decline in US Science Technology Engineering Mathematics (STEM) interests and enrollments, the National Science Foundation (NSF) and the White House have developed national strategies and provided significant budget resources to STEM education research [1-2] in the past years, with the ultimate goals being to improve both the quality and number of highly trained US educators, student workforce in STEM topics, in today’s highly competitive global markets. With the explosion of the internet’s capability and availability, it is even more critical to effectively train this future USA-STEM work-force and/or to develop effective STEM related teaching tools to reach …

15-12 Analysis Of Walking Facility Performance Guidelines For Individuals With Disabilities, Keith Christensen, Anthony Chen, Mohammad Sadra Sharifi

Transportation Research Center Reports

It is necessary to design and evaluate the effectiveness of walking facilities to accommodate the needs of all pedestrian groups, including individuals with disabilities. The Highway Capacity Manual (HCM) defines walking facility performance using a qualitative measure describing operational conditions, or level of service (LOS). However, how closely pedestrian LOS thresholds correspond to actual conditions are questionable. To overcome the limitations, a controlled large-scaled walking experiment involving individuals with disabilities was conducted at Utah State University (USU). A temporary circuit with the necessary walking facilities was constructed using eight foot self-standing walls. In total, 202 (160 without and 42 with …

14-07 Development Of Decision Support Tools To Assess Pedestrian And Bicycle Safety: Focus On Population, Demographic And Socioeconomic Spectra, Deo Chimba, Abram Musinguzi

Transportation Research Center Reports

Despite the increase of these non-motorized trips, bicyclists and pedestrians remain vulnerable road users that are often over represented in traffic crashes. While the currently used methods that identify hazardous locations serve their purpose well, majority represent a reactive approach that seeks improvement after crashes happen. This research addressed these issues and proposed decision support tools to aid the implementation of bicycle and pedestrian safety strategies. This work developed an access based tool to predict the expected number of crashes at different neighborhood levels. This tool combines the traditional methods such as those provided in the Highway Safety manual to …

Class C Fly Ash In Pavements, Kromel E. Hanna, George Morcous, Maher K. Tadros

Nebraska Department of Transportation: Research Reports

No abstract provided.

Pursuing Vision Zero In Seattle – Results Of A Systemic Safety Analysis, Rebecca Sanders

PSU Transportation Seminars

Many cities are considering pursuing Vision Zero to eliminate traffic deaths, but may not know how to move beyond addressing past crash locations toward preventing future crashes. Systemic analysis, which looks at crash patterns to determine common characteristics associated with various types of crashes, shows promise in helping cities to identify problematic locations and treatments in the hopes of preventing future crashes.

This presentation will share results from part of Seattle’s Vision Zero effort – a multi-phased analysis of pedestrian and bicycle crash data aiming to help the City understand both where crashes have occurred and where they are most …

Crp 463: University Area Multi-Modal Access Plan June 2016, William Riggs, Sam Anderson, Spencer Johnson, Garrett Wank, Alex Hunt, Lauren Leedeman, Roberto Contreras, Mark Manha, Emma Petersen, Rebecca Wysong, Shannon Boston, Augustus Grochau, Matthew Wiswell, Jerome Wu, Crp 463 Senior Project Professional Practice

City and Regional Planning Studios and Projects

This study outlines work completed as a part of the CRP 463 senior capstone class outlining a new, comprehensive approach to active transportation on the Cal Poly campus. Led by Dr. William Riggs the project assessed the current conditions, identified opportunities and constraints and then developed conceptual options for a campus active transportation plan. In addition to this process the plan involved completion of a draft Bicycle Friendly University application for the Cal Poly campus (included as a supplemental file) and envisioned conceptual design options for various locations on the campus. Key locations evaluated included the Perimeter Road / University …

Graduate-Level Civil Engineering Transportation Course Development – Oregon Tech, Roger Lindgren, David Thaemert, Charles Riley

TREC Final Reports

Three civil engineering professors at the Oregon Institute of Technology (Oregon Tech) undertook a project during the 2014-15 academic year to develop a series of transportation-related graduate courses and to modernize Oregon Tech’s Traffic Engineering Laboratory. Courses were developed in the areas of transportation water resources, transportation structures and traffic engineering. At the completion of this project, Oregon Tech is now capable of increasing the number of students educated in three key civil engineering sub-disciplines that are directly related to transportation. This project, therefore, contributes to all three U.S. Department of Transportation University Transportation Center (UTC) purpose statements: Advance transportation …

Mat-762: Building Sustainable Continuously Reinforced Concrete Pavement Using Gfrp Bars: Case Study-Highway 40 West-Montreal, Canada, Abdoulaye Sanni B., Hamdy M. Mohamed, Denis Thébeau, Brahim Benmokrane

Canadian Society for Civil Engineering

Continuously reinforced concrete pavement designs (CRCP) are premium pavement designs that are often used on heavily-trafficked roadways and urban corridors. Although CRCP typically is an effective, long-lasting pavement design, it can develop performance problems when the aggregate-interlock load transfer at the transverse cracks is degraded. The prevalence of wide cracks in CRCP has frequently been associated with ruptured steel and significant levels of corrosion. Because of that, there has been recent interest in identifying new reinforcing materials that can prevent or minimize corrosion-related issues in CRCP. Glass fibre-reinforced polymer (GFRP) bars are one product being investigated for use in CRCP …

Tra-901: Optimizing The Location Of Road Weather Information Systems (Rwis) Stations – A Sampling Design Optimization Approach, Tae J. Kwon, Liping Fu, Stephanie J. Melles, Max S. Perchanok

Canadian Society for Civil Engineering

This study presents an innovative approach to the design of a road weather information monitoring system (RWIS) that optimally combines spatial data on weather-related road surface conditions with data on traffic volume over a state-wide road network. The optimization method minimizes the spatially averaged ordinary kriging variance of hazardous road surface condition (HRSC) frequencies. Since it is desired that an RWIS should also be located at high traffic demand areas, road class data is implemented in the optimization process. Spatial simulated annealing (SSA) is used to search for the optimal RWIS network design by iteratively examining each possible location and …