Transportation Engineering Commons^™

Early-Age Strength Monitoring Of Sensor-Embedded 3d Printed Structures, Ali Kazemian, Marwa Hassan, Hassan Noorvand, Gabriel Arce, Kasra Banijamali

Publications

Construction 3D printing (C3DP) is an automated technology that has the potential to reduce the construction time and cost by utilizing different types of robotic systems. Due to the absence of formwork in C3DP, potential excessive water evaporation can cause issues to the freshly-printed structures that are exposed to the ambient curing condition. Moreover, the 3D printed elements should carry the service loads in a short time after printing to provide a load-bearing capacity. Destructive and non-destructive methods are the two types of methods that are being used in the construction industry for quality monitoring. Due to the time-consuming nature …

Understanding And Modeling Drivers’ En-Route Diversion Behavior During Congestion, Mohammad Shapouri

LSU Doctoral Dissertations

In the field of transportation, traffic assignment models primarily have been used to forecast driver route preferences, translating their choices into traffic flow patterns across networks. These models are grounded in distinct behavioral theories and strive to explain how drivers navigate routes based on network features and personal tendencies. Using an aggregation approach, conventional traffic assignment models distribute demand among paths, considering utility and attractiveness. Despite their prevalent use in transportation planning and operations, the fundamental behavioral assumptions of these models have rarely been thoroughly explored. This gap is further compounded by their limited consideration of real-time adjustments and choices …

Understanding And Modeling Drivers’ En-Route Diversion Behavior During Congestion, Mohammad Shapouri

LSU Doctoral Dissertations

In the field of transportation, traffic assignment models primarily have been used to forecast driver route preferences, translating their choices into traffic flow patterns across networks. These models are grounded in distinct behavioral theories and strive to explain how drivers navigate routes based on network features and personal tendencies. Using an aggregation approach, conventional traffic assignment models distribute demand among paths, considering utility and attractiveness. Despite their prevalent use in transportation planning and operations, the fundamental behavioral assumptions of these models have rarely been thoroughly explored. This gap is further compounded by their limited consideration of real-time adjustments and choices …

Integrating The Concept Of Complete Streets Into Pavement Preservation, Sirisha Gangireddy

LSU Master's Theses

This study is motivated by the evident gap in integrating Complete Streets principles into pavement preservation. Complete Streets opportunities, which aim to accommodate all road users, are typically encouraged in all kinds of projects including new construction, reconstruction, preservation, and rehabilitation. While the concept of Complete Streets is understood in terms of new construction (e.g., building sidewalks), its application through pavement preservation programs is not well-developed. To bridge the gap between the Complete Streets and pavement preservation, this study conducted a comprehensive review on how state Department of Transportation (DOTs) are currently incorporating Complete Streets into pavement preservation and identified …

The Effects Of Disruption Type, Trip Purpose, Gender, And Age On Driver Diversion Willingness In The United States Of America, James D. Fuller

LSU Master's Theses

When drivers encounter traffic congestion, one of the most common ways to avoid excessive delays is to divert to an alternate route. Despite the commonplace nature of such routing decisions, relatively little is known about the specific influencers, motivators, and preferences that affect diversion choices under disrupted conditions. Understanding these driver motivations is important for improving the ability of transportation authorities to plan, design, operate, and maintain transportation networks. The research described in this thesis utilizes a driver survey to investigate the situational factors and personal characteristics that may play a significant role in determining a decision to divert or …

Quantifying The Effect Of Covid-19 On Port Congestion, Corey R. Mayeux

LSU Master's Theses

The Covid-19 pandemic caused unprecedented disruptions in global supply chains and port operations, leading to congestion, delays, and container shortages. Governments implemented containment measures, affecting social behavior and economic activity. Ports faced significant challenges due to shifts in demand, labor shortages, and supply chain bottlenecks. E-commerce surge and other disruptions intensified pressures on ports. The pandemic's impact exacerbated challenges for ports and supply chains, and triggered inflationary pressures. This research aims to investigate the impact of Covid-19 on port congestion and the global supply chain at the Port of Long Beach, Port of New York and New Jersey, Port of …

Bim And Digital Twins In Infrastructure Projects: An Overview From The Transportation Professional's Perspective, Natállia Mendes

LSU Master's Theses

Transport infrastructure has undergone significant changes in recent years due to the digitalization of construction methods. Consequently, there is an increasing demand for more productive and cost-effective technologies to optimize various aspects such as time, cost, changes, waste, and errors in projects. Notably, technologies such as Building Information Modeling (BIM) and Digital Twin (DT) hold the potential to enhance the performance of infrastructure projects. While BIM has received substantial attention in recent years, Digital Twin is relatively new to the construction industry. This leads to a scarcity of studies on DT and its integration with other emerging technologies like BIM. …

Alkali-Silica Reaction Mitigation Using Alternative Supplementary Cementitious Materials, Craig Newtson, Judit M. Garcia, Seyedsaleh Mousavinezhad

Data

Over the past few decades, Class F fly ash has been widely used in concrete as a supplementary cementitious material (SCM) due, in part, to its ability to mitigate alkali-silica reaction (ASR). However, future availability of fly ash is uncertain as the energy industry shifts towards renewable sources, resulting in the closure of coal-burning power plants. Therefore, there is a growing need to find alternatives to fly ash that are both cost effective and environmentally friendly. This study aimed to evaluate the effectiveness of ground-granulated blast furnace slag (GGBFS), metakaolin, and a locally available natural pozzolan mined from a pumicite …

Accelerated Sulfate Attack Testing For Concrete, Craig Newtson, Seyedsaleh Mousavinezhad, William Toledo, Federico Aguayo

Data

Extensive research has been conducted on sulfate attack of concrete structures, however, the need to adopt use of more sustainable materials is driving a need for a quicker test method to assess sulfate resistance. Class F fly ash, which is a byproduct of coal combustion for electricity generation, has historically been used in concrete mixtures to improve sulfate resistance. However, environmental considerations and evolving energy industry has decreased its availability, requiring the identification of economically viable and environmentally friendly alternatives to fly ash. Another challenge in addressing sulfate attack durability issues in concrete is that the standard sulfate attack test …

Alkali-Silica Reaction Mitigation Using Alternative Supplementary Cementitious Materials, Craig Newtson, Judit M. Garcia, Seyedsaleh Mousavinezhad

Publications

Over the past few decades, Class F fly ash has been widely used in concrete as a supplementary cementitious material (SCM) due, in part, to its ability to mitigate alkali-silica reaction (ASR). However, future availability of fly ash is uncertain as the energy industry shifts towards renewable sources, resulting in the closure of coal-burning power plants. Therefore, there is a growing need to find alternatives to fly ash that are both cost effective and environmentally friendly. This study aimed to evaluate the effectiveness of ground-granulated blast furnace slag (GGBFS), metakaolin, and a locally available natural pozzolan mined from a pumicite …

Accelerated Sulfate Attack Testing For Concrete, Craig Newtson, Seyedsaleh Mousavinezhad, William Toledo, Federico Aguayo

Publications

Extensive research has been conducted on sulfate attack of concrete structures, however, the need to adopt use of more sustainable materials is driving a need for a quicker test method to assess sulfate resistance. Class F fly ash, which is a byproduct of coal combustion for electricity generation, has historically been used in concrete mixtures to improve sulfate resistance. However, environmental considerations and evolving energy industry has decreased its availability, requiring the identification of economically viable and environmentally friendly alternatives to fly ash. Another challenge in addressing sulfate attack durability issues in concrete is that the standard sulfate attack test …

Optimization Of The Self-Healing Efficiency Of Bacterial Concrete Using Impregnation Of Three Different Precursors Into Lightweight Aggregate, Omar Omar

LSU Master's Theses

Concrete is the most broadly used construction material; thus, developing sustainable concrete is essential to decrease greenhouse gas (GHG) emissions from concrete production. Implementation of self-healing concrete technologies is a promising approach to enhance the durability and sustainability of the transportation infrastructure. Among these technologies, bacterial concrete has the potential to seal microcracks through microbial induced calcite precipitation (MICP). Bacterial protection is essential to ensure the viability of this technology due to concrete’s harsh environment. Additionally, the success of this technology depends on the presence of an adequate mineral precursor compound and nutrient for the bacteria. As such, the main …

Examining The Impact Of Different Street Lighting Schemes On Traffic Safety And Drivers’ Behaviors At Unsignalized Intersections, Hisham Mohamed Abdu Kunnah

LSU Master's Theses

Lack of visibility is one of the main challenges that significantly impact drivers’ ability to safely perform driving tasks at night especially at unsignalized intersections. Several prior studies indicated that lighting enhances nighttime traffic safety. Nevertheless, lighting is not mandatory at unsignalized intersections in many states including Louisiana. This study aimed to investigate if lack of lighting is a contributing factor that affects traffic safety at unsignalized intersections in Louisiana. In addition, this study strived to identify current lighting policies adopted by other states, examine if there are any low-cost countermeasures implemented by other states to improve nighttime visibility, and …

Motivators And Preferences Of Route Diversion During Roadway Incidents, Grace Cole

LSU Master's Theses

When confronted with congestion and delay, drivers often divert their route. Depending on factors like purpose, urgency, destination, route alternatives, type of disruption, and mode options, common diversionary options can range from changing departure time, route, and mode to canceling a trip altogether. One of the foundational building blocks of travel forecasting is traffic assignment, which is used to distribute trips over a network using complex algorithms to aggregately represent the desire of drivers to minimize travel time.

While these assignment models are backed by decades of research and observational experience, they are also limited by the fact that they …

A New Generation Of Dense-Graded Asphalt Mixtures With Superior Performance Against Stripping And Moisture Damage, Mostafa Elseifi, Zahid Hossain, Md. T.A Sarkar, Hossam Abohamer, Mohammad Oyan

Data

The presence of moisture beneath the pavement surface is a matter of great concerns as it is responsible for significant distresses such as asphalt concrete (AC) stripping, fatigue cracking, rutting, and poor durability of asphalt mixes. The objective of this study was to evaluate and recommend an asphalt mixture design that would provide superior performance against AC stripping and cracking. To achieve this objective, a laboratory test factorial was developed to evaluate the use of nanomaterials, emerging anti-stripping agents, warm-mix asphalt technologies, and adhesion promotors. In the experimental program, the modified Lottman test (AASHTO T 283) and the Indirect Tensile …

A New Generation Of Dense-Graded Asphalt Mixtures With Superior Performance Against Stripping And Moisture Damage, Mostafa Elseifi, Zahid Hossain, Md. T.A. Sarkar, Hossam Abohamer, Mohammad Oyan

Publications

The presence of moisture beneath the pavement surface is a matter of great concerns as it is responsible for significant distresses such as asphalt concrete (AC) stripping, fatigue cracking, rutting, and poor durability of asphalt mixes. The objective of this study was to evaluate and recommend an asphalt mixture design that would provide superior performance against AC stripping and cracking. To achieve this objective, a laboratory test factorial was developed to evaluate the use of nanomaterials, emerging anti-stripping agents, warm-mix asphalt technologies, and adhesion promotors. In the experimental program, the modified Lottman test (AASHTO T 283) and the Indirect Tensile …

Comparative Analysis Of 3d Printed Bridge Construction In Louisiana, Amirhosein Jafari, Ali Kazemian, Sarah Ataei

Data

A construction 3D printing system could result in automated infrastructure development at reduced cost and time, significantly boosting overall productivity. Although there has been a growing interest in using construction 3D printing for projects such as house construction, implementing this innovative technology for infrastructure development, particularly bridge construction, has not been investigated as extensively. This study aims to compare the environmental impact of precast and 3D concrete printing (3DCP) techniques with a pedestrian bridge case study, located in Louisiana, where the bridge elements were 3D printed off-site and then transported and assembled on the bridge site. A detailed cradle-to-site life …

Comparative Analysis Of 3d Printed Bridge Construction In Louisiana, Amirhosein Jafari, Ali Kazemian, Sarah Ataei

Publications

A construction 3D printing system could result in automated infrastructure development at reduced cost and time, significantly boosting overall productivity. Although there has been a growing interest in using construction 3D printing for projects such as house construction, implementing this innovative technology for infrastructure development, particularly bridge construction, has not been investigated as extensively. This study aims to compare the environmental impact of precast and 3D concrete printing (3DCP) techniques with a pedestrian bridge case study, located in Louisiana, where the bridge elements were 3D printed off-site and then transported and assembled on the bridge site. A detailed cradle-to-site life …

Development Of Ultra-High Performance Engineered Geopolymer Composites (Uhp-Egcs), Hassan Noorvand, Miladin Radovic, Marwa Hassan, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Data

This study investigated the possibility of developing novel UHP-EGC materials for the repair and new construction of transportation infrastructure in Region 6 by utilizing locally available resources. To this end, the geopolymers (GPs) in this study were synthesized by activating metakaolin (MK) with potassium silicate and sodium silicate solutions. The solutions were manufactured in the laboratory by dissolving silica fume and potassium hydroxide (KOH) or sodium hydroxide (NaOH) in deionized water. MK-based GP binders, mortars, and fiber-reinforced composites were manufactured and evaluated to determine their density, compressive strength, tensile properties, and slant shear bond strength to Portland cement concrete (PCC). …

Development Of Ultra-High Performance Engineered Geopolymer Composites (Uhp-Egcs), Hassan Noorvand, Miladin Radovic, Marwa Hassan, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Publications

This study investigated the possibility of developing novel UHP-EGC materials for the repair and new construction of transportation infrastructure in Region 6 by utilizing locally available resources. To this end, the geopolymers (GPs) in this study were synthesized by activating metakaolin (MK) with potassium silicate and sodium silicate solutions. The solutions were manufactured in the laboratory by dissolving silica fume and potassium hydroxide (KOH) or sodium hydroxide (NaOH) in deionized water. MK-based GP binders, mortars, and fiber-reinforced composites were manufactured and evaluated to determine their density, compressive strength, tensile properties, and slant shear bond strength to Portland cement concrete (PCC). …

Toward A Safer Transportation System For Senior Road Users, Saba Doulabi

LSU Doctoral Dissertations

Senior pedestrians and drivers (65 years and older) are among the most vulnerable road users. As the population of seniors rise, concerns regarding older adults' traffic safety are growing. The advantages of using autonomous vehicles, innovative vehicle technologies, and active transportation are becoming more widely recognized to improve seniors' mobility and safety. This behooves researchers to further investigate senior road users’ safety challenges and countermeasures. This study contributes to the literature by achieving two main goals. First, to explore contributing factors affecting the safety of older pedestrians and drivers in the current transportation system. Second, to examine seniors’ perceptions, preferences, …

Rebar-Free 3d Printing Of Transportation Infrastructure, Ali Kazemian, Marwa Hassan, Hassan Noorvand, Gabriel Arce, Hassan Ahmed, Ilerioluwa Giwa

Data

This study investigates the fresh and hardened-state properties of printing mixtures including different dosages of steel fibers, especially at higher dosages which have not been investigated before. This study also considers the effects of other parameters such as sand-to-powder ratio and the limestone content on the properties of steel fiber reinforced printing materials, to reduce the Portland cement content which has a high carbon footprint. The obtained experimental results revealed that high-performance materials incorporating up to 2.5% steel fibers (by volume) can be successfully 3D printed. The mechanical properties of the reinforced mixtures improved significantly at high fiber dosages (2% …

Low-Cost Sustainable Engineered Geopolymer Composites (Egcs) For Repair And New Construction Of Transportation Infrastructure, Hassan Noorvand, Marwa Hassan, Miladin Radovic, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Data

This study evaluated the use of cost-effective alternative materials in the formulation of novel low-cost Engineered Geopolymer Composite (EGC) materials for repair and new construction of transportation infrastructure in Region 6. Previous studies and reports have shown that EGCs have excellent mechanical properties, which makes them an eco-friendly and more sustainable alternative to Engineered Cementitious Composites (ECCs). However, the mass adoption of these emerging composites is expected to be hindered by their cost, which is mainly driven by the use of PVA reinforcing fibers, silica fume (SF), and manufactured microsilica sand (MS). To address this key shortcoming, novel low-cost EGC …

Development Of Robotics & Automation Roadmap For Road Construction/Maintenance Projects, Ashrant Aryal, Chao Wang, Chintan Vijay Vora, Sueed A. Willoughby

Data

Over the past few decades, there have been no significant improvements in the construction industry's productivity. Outside the construction industry, robots have proven to be beneficial in improving productivity, safety, and quality. There is a growing interest in adopting robots in the construction industry to address these issues. As robots get introduced to the project sites, human-robot interaction becomes an important consideration for wide-scale adoption. The success of deploying robots in the construction industry depends on how well humans collaborate with the robots. This project focused on investigating the perception of various construction industry stakeholders in adopting robots in their …

Rebar-Free 3d Printing Of Transportation Infrastructure, Ali Kazemian, Marwa Hassan, Hassan Noorvand, Gabriel Arce, Hassan Ahmed, Ilerioluwa Giwa

Publications

This study investigates the fresh and hardened-state properties of printing mixtures including different dosages of steel fibers, especially at higher dosages which have not been investigated before. This study also considers the effects of other parameters such as sand-to-powder ratio and the limestone content on the properties of steel fiber reinforced printing materials, to reduce the Portland cement content which has a high carbon footprint. The obtained experimental results revealed that high-performance materials incorporating up to 2.5% steel fibers (by volume) can be successfully 3D printed. The mechanical properties of the reinforced mixtures improved significantly at high fiber dosages (2% …

Resilient 3d-Printed Civil Infrastructure With Ultra-High Performance Engineered Cementitious Composites (Uhpeccs), Hassan Noorvand, Marwa Hassan, Ali Kazemian, Gabriel Andres Arce Amador, Daniel E. Game

Publications

This study aims to develop and evaluate UHP-ECC materials for 3DP applications. To achieve this, the rheological properties of the cementitious composites were designed to accommodate 3DP functionality. Additionally, this study aimed to evaluate the hardened properties of the 3D-printed UHP-ECCs and compare them to the cast UHP-ECCs. Furthermore, the effect of variables such as sand-to-binder (S/B), fly ash-to-cement ratio (FA/C), and high-range water reducer (HRWR) content on the fresh and hardened properties of the 3D printable mixtures were evaluated. Fresh properties of mixtures were assessed by means of the flowability test, setting time test, and printability test. Hardened properties …

Resilient 3d-Printed Civil Infrastructure With Ultra-High Performance Engineered Cementitious Composites (Uhpeccs), Hassan Noorvand, Marwa Hassan, Ali Kazemian, Gabriel Andres Arce Amador, Daniel E. Game

Data

This study aims to develop and evaluate UHP-ECC materials for 3DP applications. To achieve this, the rheological properties of the cementitious composites were designed to accommodate 3DP functionality. Additionally, this study aimed to evaluate the hardened properties of the 3D-printed UHP-ECCs and compare them to the cast UHP-ECCs. Furthermore, the effect of variables such as sand-to-binder (S/B), fly ash-to-cement ratio (FA/C), and high-range water reducer (HRWR) content on the fresh and hardened properties of the 3D printable mixtures were evaluated. Fresh properties of mixtures were assessed by means of the flowability test, setting time test, and printability test. Hardened properties …

Low-Cost Sustainable Engineered Geopolymer Composites (Egcs) For Repair And New Construction Of Transportation Infrastructure, Hassan Noorvand, Marwa Hassan, Miladin Radovic, Svetlana Sukhishvili, Gabriel Arce, Ruwa Abufarsakh, Adriana A. Alvarado, Oscar Huang, Sang Zhen

Publications

This study evaluated the use of cost-effective alternative materials in the formulation of novel low-cost Engineered Geopolymer Composite (EGC) materials for repair and new construction of transportation infrastructure in Region 6. Previous studies and reports have shown that EGCs have excellent mechanical properties, which makes them an eco-friendly and more sustainable alternative to Engineered Cementitious Composites (ECCs). However, the mass adoption of these emerging composites is expected to be hindered by their cost, which is mainly driven by the use of PVA reinforcing fibers, silica fume (SF), and manufactured microsilica sand (MS). To address this key shortcoming, novel low-cost EGC …

Development Of Robotics & Automation Roadmap For Road Construction/Maintenance Projects, Ashrant Aryal, Chao Wang, Chintan Vijay Vora, Sueed A. Willoughby

Publications

Over the past few decades, there have been no significant improvements in the construction industry's productivity. Outside the construction industry, robots have proven to be beneficial in improving productivity, safety, and quality. There is a growing interest in adopting robots in the construction industry to address these issues. As robots get introduced to the project sites, human-robot interaction becomes an important consideration for wide-scale adoption. The success of deploying robots in the construction industry depends on how well humans collaborate with the robots. This project focused on investigating the perception of various construction industry stakeholders in adopting robots in their …

Permeable Curbs For Storm Water Pollution, Aldo Hernandez, Drew Johnson, Marcio Giacomoni

Data

One of the problems that increased urbanization poses is storm water pollution. Several control measures exist that are used to treat and reduce pollution in our waterways, one of those being permeable concretes; but these have not been widely adopted. The goal of this project was to develop a permeable curb apparatus that could be used in retrofitting conventional streets. The permeable curb is comprised of a permeable concrete mix with a perforated pipe running through its center, this allows for water to filter through the porous concrete and continue downstream through the perforated pipe which would eventually lead to …