Civil Engineering Commons^™

Water Damage Evaluation Of Concrete Infrastructure, Roshan Shakya

Civil Engineering Theses - Archive

This study presents an experimental program to evaluate the effect of a special waterproofing material, International Chem-Crete Pavix (CCP), on the durability of concrete. The experimental program identified the concrete mix design commonly used for pavement and other infrastructure as set by Texas Department of Transportation (TXDOT). The tests conducted include the water absorption and air void (ASTM C 642), freeze-thaw (ASTM C 666), chloride penetration (ASTM C 1202), and petrographic (ASTM C 457) test. The tests were performed on both cored and laboratory treated and untreated specimens. The absorption test was performed on the concrete specimens with water cement …

Impacts Of Signal Synchronization On Vehicular Emissions - An On-Board Measurement Case Study, Rupangi Munshi

Civil Engineering Theses - Archive

Nearly 56% of total nitrogen oxide (NOx) emissions are produced by mobile sources. Transportation and air quality managers at the state and regional level have the responsibility of developing and evaluating Transportation Control Measures (TCMs) and Transportation Improvement Plans (TIPs) to improve air quality of the region. Signal synchronization is considered to be an effective TCM to reduce corridor congestion and maintain air quality in the region. This research was carried to determine the impacts of signal synchronization on real-world, on-road emissions. A portable instrument, OBS-1300 manufactured by Horiba Instruments Inc., was used to measure on-road tailpipe emissions of NOx …

Development Of Finite Element Method-Based Model Equations For Hollow Tapered Poles, Jiwon Jung

Civil Engineering Dissertations - Archive

This study presents the development of three-parameter load-deflection models for steel and FRP poles commonly used to support closed circuit television cameras. An experimental investigation is carried out to obtain static load-deflection characteristics of tapered octagonal steel cross section and circular FRP cross section poles. Numerical results generated from three-dimensional isoparametric finite element model (FEM) considering coupled nonlinear algorithms for material, geometric, contact, and pre-tensioning effects are compared with those obtained experimentally. Eight-node elsto-plastic solid element is employed to model the pole, end-plate, bolts, concrete base, and laboratory reaction floor. The laboratory reaction floor is modeled with a thick plate …

Performance Evaluation Of Bamboo Reinforced Concrete Beams, Leena Khare

Civil Engineering Theses - Archive

This study presents the evaluation of the feasibility of the use of bamboo as a potential reinforcement in concrete structural members. To achieve this objective a series of tensile tests on three types of bamboo Solid; Moso; and Tonkin; were conducted to obtain their constitutive relation. Also, four-point bending tests on concrete beams reinforced with bamboo were performed to identify their behavior compared to steel reinforced concrete members. Tensile tests specimens were prepared by cutting the bamboo typically in 1/2 in (13 mm) wide strips of 9 to 12 in (228 mm to 305 mm) in length. In order to …

Performance And Check-Out Verification Testing Of A New True Triaxial Apparatus Using Partially Saturated Silty Sand, Jae Hyun Park

Civil Engineering Theses - Archive

A stress-controlled, flexible boundary, true triaxial (cubical) testing apparatus has been developed to test 3-inch cubical specimen of partially saturated soil under different moisture contents and for a wide range of multiaxial stress paths. A series of HC, CTC, TC, TE, and SS tests were conducted in order to perform a thorough performance and check-out verification testing of the newly developed device by investigating the multiaxial stress-strain response of partially saturated silty sand specimens artificially prepared in the laboratory. The development of the apparatus, specimen preparation process, test procedure, and the corresponding validation of its suitability for testing partially saturated …

Nonlinear Finite Element Model Analysis Of Human Accommodation Lens, Tri Le

Civil Engineering Theses - Archive

The crystalline human lens is modeled by using the finite element software, ABAQUS/CAE Version 6.5-1 as an axisymmetric shell to study the optical power and displacement of anterior and posterior poles induced due to zonule traction. Several different element types were tested to obtain the optimum mesh. These elements were three and six-noded triangular hybrid and four-noded quadrilateral hybrid for modeling of the cortex and nucleus. Constant strain triangular and regular quadrilateral elements were examined for modeling the capsule. One dimensional two degree of freedom spring elements were used to model the anterior, posterior, and equatorial zonules. Five different lens …

Modern Technologies For Design Data Collection, James Samuel Bethel, Steven D. Johnson, Monica Prezzi, Boudewijn H. W. Van Gelder, Bob G. Mccullouch, Ali Fuat Cetin, Seungwoo Han, Mosab Hawarey, Changno Lee, Aparajithan Sampath, Jie Shan

JTRP Technical Reports

Design data collection involving the use of Lidar instrument, in conjunction with GPS proves to be very effective. Data required to model two bridges over the I-70 was collected on a single day, involving five and six sessions with Lidar equipment. Even though the data was collected on two bridges, it did not cause any disruption of the traffic, either on the Interstate or on the bridges. A major cause of concern during survey activities, particularly along interstates is safety, both for the motorists as well as the people involved in data collection. Lidar data collection was found to be …

Stochastic Modeling Of The Permeability Of Randomly Generated Porous Media, Yusong Li, Eugene Leboeuf, P. K. Basu, Sankaran Mahadevan

Department of Civil and Environmental Engineering: Faculty Publications

Permeability of porous media in subsurface environments is subject to potentially large uncertainties due to the heterogeneity of natural systems. In this study, a first-order reliability method (FORM) is combined with a lattice Boltzmann method (LBM) to estimate the permeability of randomly generated porous media. The proposed procedure provides an increased ease of addressing complex pore structures by employing LBM to model fluid flow, while inheriting the computational efficiency from FORM. Macroscale- equivalent permeability can thus be estimated with significantly reduced computational efforts, while maintaining a connection to the complex microscale fluid dynamics within a pore structure environment. Implemented on …

Bs News

Building Services Engineering

No abstract provided.

Quality Of Common Salt In The Tanzanian Market, Kamwanya E

Tanzania Journal of Engineering and Technology (TJET)

The quality of edible salts in the Tanzanian market has been studied by comparing the levels of iodine, heavy metals, and non-metals. Among the 19 analyzed local salt samples, only two of them—Kipepeo salt (76.67 mg/kg) and Super salt (79.95 mg/kg)—met the recommended level of iodine as per TBS (Tanzania Bureau of Standards) specifications. Other brands have iodine levels below the TBS specification.

Degradation Of Waterfront Reinforced Concrete Structures At The Port Of Dar Es Salaam, I Sanga

Tanzania Journal of Engineering and Technology (TJET)

The paper summarises the results of an investigation done on piers at the Dar es Salaam Port. The problem facing these structures and marine facilities is their exposure to aggressive environmental phenomena. The paper presents an investigation of the strength and corrosion of concrete seaport piers so as to determine degradation of the reinforced concrete waterfront structures in the port of Dar es Salaam. For instance the structures at a dhow quay terminal had been in use for about 100 years. The facility was in bad condition as the concrete had been badly damaged due to corrosion. Some of the …

Cement Oonded Wood Wool Board As A Building Material For Low Cost Housing, A Mrema

Tanzania Journal of Engineering and Technology (TJET)

This paper gives results of a preliminary study on the properties of cement bonded wood-wool boards manufactured as composites by using wood-wool (excelsior) from podocarpus spp wood species and ordinary Portland cement. Two main parameters were varied during the investigation and these were the width of the wood-wool and the cement to wood-wool ratio. Results show that the optimum mix proportion is three parts of cement to two parts of wood-wool by weight and that a smaller excelsior width gives higher board strengths. The results from tests on flexural strength, compressive strength and tensile strength far exceeded the requirements of …

Earth Building In Tanzania - Use Of Soil Stabilized Bricks And Blocks, A Mrema

Tanzania Journal of Engineering and Technology (TJET)

This paper presents experimental results of investigations done on the use of stabilized earth (soil) for the manufacture of bricks and blocks. The soil used was clayey sand of low plasticity. Two types of stabilizers were used to make stabilized bricks and these were cement and a combination of cement and lime. Different stabilizer proportions were employed. Results of tests carried on these bricks at 28 days indicate an optimum mix proportion of 7% cement if cement is used alone and an optimum mix proportion of 5% each if a combination of lime and cement is used as a stabilizer. …

Low Cost Slab Manufactured From Masonry Slab Elements, John Makunza

Tanzania Journal of Engineering and Technology (TJET)

The construction of bungalow houses requires sufficient space to accommodate all the requirements as per the client’s wish. The idea of low-rise or high rise buildings is very remote for most of the people due to the high costs of construction involved. Much of the said cost is due to the concrete floor slab as it consumes a bigger portion of concrete material when compared to beams and columns. In this paper, a study presented is on a new form of voided slab constructed from masonry slab elements that do not utilize formwork and consumes less concrete material. The slab …

Ceramic Properties Of Chimala Kaolin Clay, Leonard Akwilapo

Tanzania Journal of Engineering and Technology (TJET)

The physico-chemical properties of kaolinite clays occurring in abundance near Chimala were studied with a view of finding out their suitability in sanitary ware production. The viscosity of the clay was found to be within the range acceptable in industrial application (≤ 500 cp for 70% solids), enhancing its prospects for the manufacture of slip cast shapes with satisfactory properties. The chemical composition of the clay reveals a high content of Fe₂O₃, 1.48%, which is expected to affect the translucency and colour of the finished ware. However, such quantity would not have detrimental effects in the production of sanitary ware. …

Influence Of Optical Fiber Coating Damage In The Light Transmissivity Characteristics Of Microbend Sensors, Franz Campero, Paul J. Cosentino, David C. Fleming, Edward H. Kalajian, Barry G. Grossman

Mechanical and Civil Engineering Faculty Publications

A laboratory testing and engineering modeling study was completed to determine the influence of fiber optic coating damage caused by microbend contact on the performance of microbend sensors developed based on relatively low cost single-sided microbending technique using a multimode optical fiber. A testing method was designed, developed and implemented to determine the loads that caused optical fiber glass-coating debonding and coating fracture. Finite Element models of the fiber-deformer system were developed to study the failure modes and predict the stresses that caused this failure. Loads and displacements predicted by Finite Element models were found to be in good agreement …

Bs News

Building Services Engineering

No abstract provided.

Mechanics Of Biocell Landfill Settlements, Chamil Hiroshan Hettiarachchi

Dissertations

Prediction of landfill gas generation and settlements are of concerns in design and maintenance of biocell landfills. Accurate settlement prediction is essential for design of piping systems used for the delivery of re-circulated leachate and recovery of landfill gas. Landfill settlement is the result of change in overburden stresses and biodegradation of waste. Biodegradation-induced settlement results from the re-arrangement of waste skeleton in response to the decomposition of waste mass.

Current practice of landfill settlement modeling is predominantly empirical, thus most of the available techniques make no attempt to simulate the real mechanisms of waste settlement. Traditionally compressibility index is …

Utility Of Remote Sensing Data In Retrieval Of Water Quality Consituents Concentrations In Coastal Water Of New Jersey, Ting Yu

Dissertations

Three important optical properties used for monitoring coastal water quality are the concentrations of chlorophyll (CHL), color dissolved organic matter (CDOM) and total suspended materials (TSM). Ocean color remote sensing, a technique to collect color data by detection of upward radiance from a distance (Bukata et al.,1995), provides a synoptic view for determining these concentrations from upwelling radiances. In the open ocean (Case-I), it is not difficult to derive empirical algorithms relating the received radiances to surface concentrations of water quality parameters. In coastal waters (Case-Il), there are serious unresolved problems in extracting chlorophyll concentration because of high concentration of …

Ronan Point Apartment Tower Collapse And Its Effect On Building Codes, Cynthia Pearson, Norbert Delatte

Civil and Environmental Engineering Faculty Publications

In the early morning hours of May 16, 1968, the occupant of apartment 90 on the 18th floor of the 22-story Ronan Point apartment tower, in London, lit a match to brew her morning cup of tea. The resulting gas explosion initiated a partial collapse of the structure that killed four people and injured 17 (one of whom subsequently died). On investigation, the apartment tower was found to be deeply flawed in both design and construction. The existing building codes were found to be inadequate for ensuring the safety and integrity of high-rise precast concrete apartment buildings. The Larsen–Nielson building …

Minimum Velocities For The Suspension Of Fine Sediment In The Green River Canal, Michael W. Stoeber

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

This paper focuses on a canal in the Gunnison Valley, located in central Utah, which diverts water from the sediment-laden Green River. Grain size analyses were performed on sediment samples taken from the canal. These grain size analyses were used to determine the grain size distribution of the fine sediment, classify the fine sediment, and compare the fine sediment to a sediment deposit in the Green River. The critical incipient velocity for the D₅₀ and D₁₀₀ and the critical grain entrainment velocity corresponding to the D₉₅ were determined through flume experimentation. Two methods, developed by prior researchers, …

Failure Of Cold-Formed Steel Beams During Concrete Placement, Norbert Delatte

Civil and Environmental Engineering Faculty Publications

During a concrete placement on the second story of a building under construction, the supporting cold-formed steel beams collapsed. Four workers were injured. The collapse occurred while concrete was being placed onto steel decking on the second floor of the structure. Cold-formed steel beams, without shoring, supported the steel decking. Analysis of the steel beams under the weight of concrete and workers using the applicable American Concrete Institute and American Iron and Steel Institute documents indicated that the beams were overstressed for construction loads. After the collapse, part of the structure was rebuilt using thicker beams. For the reconstruction, the …

Bs News

Building Services Engineering

No abstract provided.

Inside Unlv, Erin O'Donnell, Diane Russell, Carol C. Harter

Inside UNLV

No abstract provided.

3d Modelling With Linear Approaches Using Geometric Primitives, Mochammad Zuliansyah

Makara Journal of Technology

In this paper, we study linear approaches for 3D model acquisition from non-calibrated images. First, the intrinsic and extrinsic camera calibration is taken into consideration. In particular, we study the use of a specific calibration primitive: the parallelepiped. Parallelepipeds are frequently present in man-made environments and naturally encode the affine structure of the scene. Any information about their euclidean structure (angles or ratios of edge lengths), possibly combined with information about camera parameters is useful to obtain the euclidean reconstruction. We propose an elegant formalism to incorporate such information, in which camera parameters are dual to parallelepiped parameters, i.e. any …

Bs News

Building Services Engineering

No abstract provided.

Synthesis Dibenzyl Terephthalate Through Depolimerization Of Poly (Ethylene Terephthalate) As Alternative Of Waste Plastics Recycling, Suwardi Suwardi, Crys Fajar Partana, Agus Salim, Dyah Anitasari

Makara Journal of Technology

Synthesis Dibenzyl Terephthalate Through Depolimerization of Poly(ethylene terephthalate) as Alternative of Waste Plastics Recycling. Synthesis dibenzyl terephathalate were done through PET degradation by refluxing in benzyl alcohol at 145oC temperature for 20, 24, and 28 hours in the presence of zinc acetate catalyst. The result of degradation was purified by recristalization in methanol and then melting point (mp), FTIR, 1H NMR spectra, and TLC spot were determined. The melting point of product degradation for 28 hours was 98-99 oC. Based FTIR spectra known that compunds of product degradation have OH, C=O, C-O, CH, monosubstituted benzene, disubstituted benzene groups, while on …

Dipole Magnetization Effect To Kerosene Characteristics, Mochamad Chalid, Nelson Saksono, Adiwar Adiwar, Nono Darsono

Makara Journal of Technology

Dipole Magnetization Effect to Kerosene Characteristics. Investigation of kerosene characteristics has been done by ex-situ dipole magnetization. The results show that magnetization technique can be able to influence kerosene characteristics. Polarity and viscosity of the kerosene are observed by measuring refractive index and viscosity. An hour of 4330 Gauss flux magnetic will increase refractive index from 1.447 to 1.449 and decrease the viscosity from 1.278 to 1.256. Those changing support de-clustering occurrence and polarity increment of kerosene molecule. Gas chromatography and infrared result show that those changing do not alter kerosene structure and composition.

Study Of 2d And 3d Optical Beam Induced Voltage Imaging Using Photoresistor Sensor, Warsito Warsito, Sri Wahyu Suciyati, Susi Harnani, Akhmad Dzakwan

Makara Journal of Technology

Study of 2D and 3D Optical Beam Induced Voltage Imaging Using Photoresistor Sensor. This article shows a method to study OBIV (optical beam induced voltage) imagerie system, that usually employ a laser scanning microscopy system. The OBIV imagerie system developed use a photoresistor sensor as a sample and simultaneously it can be used for analyzing its inhomogeneity response. Resolution of the system is still low, about 350μm due to high value of incident light diameter. The results inform that photoresistor sensors gave an optimum response if the incident light hits the center of sensible zone.

Flexi Radio Base Station (Rbs) Performance Analysis Of Voice And Trafic On Kota 2 Jakarta Barat Base Station Control (Bsc), Mushfar Ferdian, Fitri Yuli Zulkifli

Makara Journal of Technology

Flexi Radio Base Station (RBS) Performance Analysis of Voice and Trafic on Kota 2 Jakarta Barat Base Station Control (BSC). The CDMA 2000 technology uses circuit switch method to handle voice traffic and packet switch method to handle data traffic between the user and RBS (Radio Base Station). These two parameters can be used to measure performance of the network generally, so it is necessary to optimize them. This paper analyze the performance of RBS by measuring its parameters such as set up failure ratio, drop ratio, and occupancy. Furthermore, the traffic increment is calculated too in order to provide …