Civil Engineering Commons^™

Mechanical And Transport Properties Of Alkali-Activated Natural Pozzolans As Sustainable Binders, Brittany Radke

Calvert Undergraduate Research Awards

OPC production accounts for 5 to 7% of the global carbon dioxide (CO₂) emissions, contributing to global warming. The desire to reduce CO₂ emissions and produce more durable concrete has given impetus to search for new binders. It is suggested that alkali-activated natural pozzolans have the potential for use as a sustainable replacement for OPC in concrete.

The current study presented herein evaluated fresh, mechanical, and transport properties of alkali-activated natural pozzolan mortars containing various concentrations of sodium hydroxide solutions as an alkaline activator. To this aim, alkali-activated natural pozzolan mortars were made with concentrations of sodium …

Implementing Green Roofs On Movie Theaters And Shopping Centers: Business Cases In Profitable Sustainability, Ryan J. Miller

Pomona Senior Theses

This thesis presents the business case for installing green roofs on movie theaters and shopping centers. These businesses can then derive increased profits from the environmental benefits of reduced energy use and increased stormwater retention. After presenting the basic design and benefits of a green roof, the thesis develops stand-alone business plans for a movie theater and shopping center. The author finds that green roofs are a profitable sustainability solution for the commercial enterprise.

Microgrid Development Using A Grid Tie Inverter, Hartono Budi Santoso, Budiyanto Budiyanto

Makara Journal of Technology

The use of renewable energy sources (RES), especially photovoltaic (PV), to meet the demand of electrical energy has been getting a great deal of attention as an alternative solution to electrical energy deficit problems. RES are being applied in power systems in a variety of configurations including microgrid systems. One of the characteristics of a microgrid is capability to supplying power to grid when there is an excess power to supply local load. This research examines the chances of saving power consumption from grid using power converters grid tie inverter (GTI) in a microgrid configuration. The test is done by …

Surface Treatment Of Fly Ash For Improving The Tensile Strength Of Fly Ash/Unsaturated Polyester Composites, Sugiman Sugiman, Paryanto Dwi Setyawan

Makara Journal of Technology

The paper presents the surface treatment of fly ashes using acid and alkali solution on the tensile strength of the fly ash/unsaturated polyester (UP) composites. Sulfuric acid (H2SO4), hydrofluoric acid (HF) and sodium hydroxide (NaOH) solution with concentration of 0%, 5%, 10%, 15%, and 20% (by weight) were used for surface treatment of fly ashes. Generally, the tensile strength of the treated fly-ash/UP composites shows a significant increase compared to the untreated fly ash. Of all surface treatments studied, the optimum tensile strength was obtained at a concentration of 10%. At this concentration, at a fly ash content of 30% …

Recycling Roof Tile Waste Material For Wall Cover Tiles, Ambar Mulyono, Silfia Mona Aryani, Joko Lulut

Makara Journal of Technology

Prior research on roof tile waste treatment has attempted to find the appropriate technology to reuse old roof tile waste by create wall cladding materials from it. Through exploration and experimentation, a treatment method has been discovered to transform the tile fragments into artificial stone that resembles the shape of coral. This baked clay artificial stone material is then processed as a decorative element for vertical surfaces that are not load-bearing, such as on the interior and exterior walls of a building. Before applying the fragments as wall tiles, several steps must be taken: 1) Blunting, which changes the look …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.

Semiconductor Thermal Neutron Detector, Toru Aoki, Aki Miyake, Takayuki Nakano, Akifumi Koike, Hisashi Morii, Hidenori Mimura

Makara Journal of Technology

The CdTe and GaN detector with a Gd converter have been developed and investigated as a neutron detector for neutron imaging. The fabricated Gd/CdTe detector with the 25 mm thick Gd was designed on the basis of simulation results of thermal neutron detection efficiency and spatial resolution. The Gd/CdTe detector shows the detection of neutron capture gamma ray emission in the 155Gd(n, g)156Gd, 157Gd(n, g)158Gd and 113Cd(n, g)114Cd reactions and characteristic X-ray emissions due to conversion-electrons generated inside the Gd film. The observed efficient thermal neutron detection with the Gd/CdTe detector shows its promise in neutron radiography application. Moreover, a …

Radiation Characteristics Of A Planar Strip Dipole Antenna And A Slot Dipole Antenna For Thz Applications, Catur Apriono, Eko Tjipto Rahardjo

Makara Journal of Technology

The development of a THz system often requires a device that is used to radiate or detect THz waves. One way to fulfill this requirement is to use an antenna. Therefore, we need to consider the radiation characteristics of an antenna working in the THz region. In this paper, we present simulation study of two dipole antennas, i.e. a planar strip dipole antenna and a slot dipole antenna. The simulation results show that a planar strip dipole antenna has a better radiation efficiency (more than 95%) compared to the slot dipole. It also shows that an efficiency of more than …

The Effect Of Pressing Temperature And Time On The Quality Of Particle Board Made From Jatropha Fruit Hulls Treated In Acidic Condition, Apri Heri Iswanto, Fauzi Febrianto, Yusuf Sudo Hadi, Surdiding Ruhendi, Dede Hermawan

Makara Journal of Technology

The high of pH of jatropha fruit hulls causes the negative properties of particleboard made from this material. Adjusting the particle acidity and pressing conditions (temperature and time) is among the technical modifications available to improve this particleboard’s properties. Particle acidity has been adjusted in a previous research project, and immersing the particles in acetic acid was found to be the best treatment in this preliminary research. In order to improve the particleboard’s properties, an experiment was conducted to determine the best pressing temperature and time. The objective of the research was to evaluate the influence of pressing temperature and …

One-Dimensional Compressibility Of Intermediate Non-Plastic Soil Mixtures, Sean E. Salazar

Civil Engineering Undergraduate Honors Theses

The results of high stress, one-dimensional compression testing on intermediate soils are presented. Nevada Sand and silica silt mixtures were subjected to very high vertical stresses (140 MPa) in one-dimensional, monotonic compression. Each soil mixture was tested in a nominally loose condition. A specially designed mold with an integrated sensor array was fabricated to contain the soil during pre-consolidation and loading. The 1-D compression curve was plotted for each mixture in the double-logarithmic void ratio (e), and vertical effective stress (σ’v) space and characteristics of the Limiting Compression Curve (LCC) were identified. Initial and post test grain size distribution curves …

In-Plane Loading Of Brick Veneer Over Wood Shear Walls, Elias Anis Toubia, James M. Lintz

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

In the design of wood stud walls with brick veneer, current design building codes specify that the wood stud wall should resist all in-plane and out-of-plane loads (IBC 2009). For out-of-plane loads, this assumption is entirely justified as the brittle brick veneer will crack and lose its capacity to resist bending. For in-plane loads, the brick veneer is significantly stiffer than the wood shear wall, and the veneer is unlikely to crack before the wood shear wall reaches its allowable capacity. The assumption that the wood shear wall resists the entire load is based on the further assumption that the …

Heavy Vehicle Performance During Recovery From Forced-Flow Urban Freeway Conditions Due To Incidents, Work Zones And Recurring Congestion, Alexander Drakopoulos, Yue Liu, Alan Horowitz

Civil and Environmental Engineering Faculty Research and Publications

Information contained in the Highway Capacity Manual on the influence heavy vehicles have on freeway traffic operations has been based on few field data collection efforts and relied mostly on traffic simulation efforts. In the 2010 Manual heavy vehicle impact is evaluated based on “passenger car equivalent” values for buses, recreational vehicles and trucks. These values were calibrated for relatively uncongested freeway conditions (levels of service A through C) since inadequate field data on heavy vehicle behavior under congested conditions were available. A number of field data collection efforts, that were not included in deriving the passenger car equivalent values …

Research Project Work Plan For Impact Of Cascadia Subduction Zone Earthquake On The Seismic Evaluation Criteria Of Bridges, Peter Dusicka

Civil and Environmental Engineering Faculty Publications and Presentations

The goal of this project is to provide ODOT with the best rational estimate of ground acceleration values for designing new and retrofitting existing bridges. The objectives are to:

• evaluate the hazard by contrasting the acceleration values from individual CSZ events to PSHA values
• provide experimental evidence of damage difference under longer duration shaking expected from CSZ event

Approximating The Seismic Amplification Effects Experienced By Solar Towers Mounted On The Rooftops Of Low-Rise Industrial Buildings, Peter Luiz Balla

Master's Theses

This thesis investigates the acceleration amplification experienced by solar towers mounted on the rooftops of low-rise industrial buildings during a seismic event. Specifically, this thesis looks to assess the validity of using amplification factors adopted by the ASCE 7-05Minimum Design Loads for Buildings and Other Structures to approximate seismic acceleration amplification for roof-mounted solar towers. To investigate the validity of the ASCE 7-05 amplification factors, this thesis conducts timehistory analyses of three theoretical solar towers mounted on the roof of a case study building. The time history analyses are conducted in the finite element computer modeling program SAP 2000 using …

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

Real-Time-Hybrid-Simulation Of Multi-Degree-Of-Freedom Systems With Multiple Time Steps, Lanxi Liu, Arun Prakash

The Summer Undergraduate Research Fellowship (SURF) Symposium

Computational simulation and physical experiments are both widely used in testing the response of a structure under earthquake loadings, but physical experiments can be expensive for large problems and numerical may result in the loss of important structural behavior caused by a large amount of assumptions. Real-time hybrid simulation (RTHS) is a combination of these two approaches, which uses both a numerical and physical substructures that interact in real time to simulate structural behavior. The numerical and physical substructures are connected using a transfer system that enforces compatibility between them. The physical substructure needs to be run at a very …

Validation Of Earthquake Simulations And Their Effects On Tall Buildings Considering Spectral Shape And Duration, Ting Lin, Gregory Deierlein, Nenad Bijelic

Civil and Environmental Engineering Faculty Research and Publications

No abstract provided.

The Effect Zeolite Addition In Natural Rubber Polypropylene Composite On Mechanical, Structure, And Thermal Characteristics, Nurdin Bukit, Erna Frida

Makara Journal of Technology

This study was conducted to determine the effect of zeolite as filler on mechanical properties, and thermal structure blends of natural rubber and polypropylene (NR/PP). In this study, NR/PP/PP-g-MA blends was filled uncalcined zeolite and calcined zeolite at different weight percent of the 2, 4, and 6%. Samples were characterized to determine the tensile strength, fracture elongation and Young's modulus. Structure of the samples was investigated using XRD method and thermal characteristics were analyzed using DTA/TGA technique. The results obtained for tensile strength showed a significant influence with the addition zeolite of the NR/PP blends at 2% by weight of …

Characteristics Of Vacuum Freeze Drying With Utilization Of Internal Cooling And Condenser Waste Heat For Sublimation, Muhammad Idrus Alhamid, Nasruddin Yusuf, Indra Teuku Meurah Mahlia, Engkos Ahmad Kosasih, Muhamad Yulianto, Rio Ricardi

Makara Journal of Technology

Vacuum freeze drying is an excellent drying method, but it is very energy-intensive because a relatively long drying time is required. This research investigates the utilization of condenser waste heat for sublimation as a way of accelerating the drying rate. In addition, it also investigates the effect of internal cooling combined with vacuum cooling in the pressure reduction process. Jelly fish tentacles were used as the specimen, with different configurations for condenser heat waste and internal cooling valve opening. The results show that heating with condenser heat waste can accelerate the drying rate up to 0.0035 kg/m2.s. In addition, pre-freezing …

A New Experimental Approach To Evaluate Plasma-Induced Damage In Microcantilever, Yuki Nishimori, Shinji Ueki, Masakazu Sugiyama, Seiji Samukawa, Gen Hashiguchi

Makara Journal of Technology

Plasma etching, during micro-fabrication processing is indispensable for fabricating MEMS structures. During the plasma processes, two major matters, charged ions and vacuum–ultraviolet (VUV) irradiation damage, take charge of reliability degradation. The charged ions induce unwanted sidewall etching, generally called as “notching”, which causes degradation in brittle strength. Furthermore, the VUV irradiation gives rise to crystal defects on the etching surface. To overcome the problem, neutral beam etching (NBE), which use neutral particles without the VUV irradiation, has been developed. In order to evaluate the effect of the NBE quantitatively, we measured the resonance property of a micro-cantilever before and after …

Fatigue Life Prediction Of The Keel Structure Of A Tsunami Buoy Using Spectral Fatigue Analysis Method, Angga Yustiawan, Ketut Suastika, Wibowo Harso Nugroho

Makara Journal of Technology

One of the components of the Indonesia Tsunami Early Warning System (InaTEWS) is a surface buoy. The surface buoy is exposed to dynamic and random loadings while operating at sea, particularly due to waves. Because of the cyclic nature of the wave load, this may result in a fatigue damage of the keel structure, which connects the mooring line with the buoy hull. The operating location of the buoy is off the Java South Coast at the coordinate (10.3998 S, 108.3417 E). To determine the stress transfer function, model tests were performed, measuring the buoy motions and the stress at …

The Plasma Electrolysis Phenomenon In A Two-Compartment Reactor For Chlor-Alkali Production, Nelson Saksono, Fakhrian Abqari, Setijo Bismo

Makara Journal of Technology

Chlor-alkali is one of the most important processes in the chemical industry. It produces chlorine and caustic soda, which become the main feedstock of daily products. The aim of this study is to report the phenomenon of plasma electrolysis and how it can be used in chlor-alkali production for more efficient energy consumption. When the plasma is formed, the current fluctuates and gradually declines. Plasma electrolysis begins with the process of electrolysis itself. Due to Joule heating, gas bubbles are formed and a sheath is made on both electrodes, resulting in the plasma field. Plasma electrolysis can be identified by …

Observation Of Photovoltaic Effect And Single-Photon Detection In Nanowire Silicon Pn-Junction, Arief Udhiarto, Sri Purwiyanti, Daniel Moraru, Takeshi Mizuno, Michiharu Tabe

Makara Journal of Technology

We study nanowire silicon pin and pn-junctions at room and low temperature. Photovoltaic effects are observed for both devices at room temperature. At low temperature, nanowire pn-junction devices show their ability to detect single photon. This ability was not been observed for pin devices. Phosphorus-boron dopant cluster in the depletion region is considered to have the main role for single-photon detection capability. Fundamental mechanism of dopant-based single-photon detection in nanowire pn-junction is described in details.

Influences Of Surface Morphology Of Nanostructured Rutile Tio2 Nanorods/Nanoflowers As Photoelectrode On The Performance Of Dye-Sensitized Solar Cell, Mohd Khairul Bin Ahmad, Kenji Murakami

Makara Journal of Technology

Aligned Rutile TiO2 nanorods (r-TNRs) and TiO2 nanoflowers (r-TNFs) were successfully prepared by hydrothermal method. Using hydrochloric acid (HCl) as chelating agent and titanium butoxide (TBOT) as precursor, aligned r-TNRs with r-TNFs were successfully growth onto fluorine-doped tin oxide (FTO) with different morphologies. The influences of surface morphologies to the rutile based Dye-sensitized solar cell (DSC) efficiency are discussed. The highest lightto- electric energy conversion efficiency, 1.80% is achieved using different concentration under simulated solar light illumination of 100 mWcm-2 (1.5 AM).

Improvement In Performance Of Zno Based Dsc Prepared By Spraying Method, Rangga Winantyo, Devinda Liyanage, Kenji Murakami

Makara Journal of Technology

This paper reports the effect of TiCl4 on the performance of ZnO based DSC. ZnO was used due to its stability against photo-corrosion and photochemical properties similar to TiO2. Thin films of nanocrystalline ZnO were deposited on transparent conducting oxide glass using spray method. The ZnO films were treated using TiCl4. The cell’s efficiency was found to be 2.5% with TiCl4 post-treatment and 1.9% without TiCl4 post-treatment.

Determining The Air Gap Length Of An Axial Flux Wound Rotor Synchronous Generator, Abdul Multi, Iwa Garniwa, Uno Bintang Sudibyo

Makara Journal of Technology

The air gap length of the designed axial flux wound rotor (AFWR) synchronous generator is determined properly according to the design parameters. One of the distinct advantages of an axial flux (AF) machine is its adjustable air gap. An AF generator’s performance might be controlled by adjusting its air gap. The designed generator has a smallscale capacity that has 1 kW, 380 V, and 50 Hz. The windings are laid into slots made from laminated core. The slots are carved in the face of the stator and rotors. The generator has a single-double-sided slotted wound stator sandwiched between twin rotors. …

Production Optimization For Plan Of Gas Field Development Using Marginal Cost Analysis, Suprapto Soemardan, Widodo Wahyu Purwanto, Arsegianto Arsegianto

Makara Journal of Technology

Gas production rate is one of the most important variables affecting the feasibility plan of gas field development. It take into account reservoir characteristics, gas reserves, number of wells, production facilities, government take and market conditions. In this research, a mathematical model of gas production optimization has been developed using marginal cost analysis in determining the optimum gas production rate for economic profit, by employing the case study of Matindok Field. The results show that the optimum gas production rate is mainly affected by gas price duration and time of gas delivery. When the price of gas increases, the optimum …

Structural Reliability Analysis Of Corroded Steel Girder Bridge, Mohammed Shaalan Al Badran

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The natural aging, environmental impact, and appropriate design are certainly playing a serious role in safety of the bridges function. The functional safety of bridge constitutes a prime element of the transportation system serving commuters, passengers and freight. According to Federal Highway Administration, the steel bridges share represents a large amount of the United States’ bridges. In last century, the collapse of both the Silver Bridge at Point Pleasant, West Virginia over the Ohio River on December 15, 1967 and over the Mianus River Bridge in Connecticut on June 28, 1983 showed that steel corrosion has been the leading reason …

The Effect Of Truck Permitting Policy On Us Bridge Loading, Eugene J. Obrien, Bernard Enright, Cathal Leahy

Conference papers

No abstract provided.

Another Look At The Collapse Of Skyline Plaza At Bailey’S Crossroads, Virginia, Jeffrey Schellhammer, Norbert Delatte, Paul A. Bosela

Civil and Environmental Engineering Faculty Publications

On March 2, 1973, the Skyline Plaza apartment building in Bailey’s Crossroads, Virginia collapsed while under construction. The Occupational Health and Safety Administration (OSHA) requested an investigation from the National Bureau of Standards [(NBS); now the National Institute of Standards and Technology (NIST)]. The NBS team concluded that the most likely cause of the collapse was a punching shear failure of the 23rd floor slab. The two factors that contributed to this were premature removal of shores below the 23rd floor slab, and the low strength of the 23rd floor concrete in the area supporting the weight of the 24th …