Civil Engineering Commons^™

Underwater Explosion Energy Dissipation Near Waterborne Infrastructure, Paul R. Smith

Theses and Dissertations--Civil Engineering

Underwater explosions pose a significant threat to waterborne infrastructure though destructive pressure waves that can travel significant distances through the water. However, the use of bubble screens can attenuate the peak pressure and energy flux created by explosions to safe levels. This study investigates the prediction of pressure wave characteristics based on accumulated data, the damage potential of underwater explosions based on applied loads and effective material strength, and the bubble screen parameters required to prevent damage. The results were compiled to form a procedure for the design and implementation of a bubble screen the protection of waterborne infrastructure.

Enhancing The Strength Properties Of Fly Ash By Adding Waste Products, Alfred J. Susilo

Theses and Dissertations--Civil Engineering

For this study, the main material to be investigated is Class F fly ash that originates from the combustion of Appalachian coal. Alone, fly ash exhibits poor strength properties and is susceptible to liquefaction when subject to dynamic loading. This research is focused on investigating the effect of adding materials that would otherwise be considered as waste products to the fly ash. Materials to be considered include crumb rubber, shredded carpet and shredded paper. The benefits from this research are twofold. First, provide a method to stabilize fly ash. For large masses of fly ash such as those found at …

Using Unmanned Aerial Systems (Uas) And Photogrammetry To Remotely Assess Landslide Events In Near Real-Time, Jordan T. Keeney

Theses and Dissertations--Civil Engineering

Commercially available unmanned aerial systems (UAS) and photogrammetry software have undergone rapid advancements in recent years. However, the use of UAS and photogrammetry techniques for monitoring surface landform deformation has not been adopted for the most part due to complicated workflows and complex UAS systems. This study demonstrates the ability to monitor landslides in near-real time with commercially available UAS and photogrammetry software using direct georeferencing and co- registration techniques. The results of this research were then assessed to develop an optimal workflow for the rapid assessment of surface deformations with direct georeferenced UAS obtained imagery and photogrammetry software.

Sinkhole Monitoring Using Groundwater Table Data, Ton Tu

Electronic Theses and Dissertations

Florida might be one of the most sinkhole-active areas on the earth. Due to its unpredictability and significance of occurrence, the development of sinkhole monitoring techniques is imperative to minimize sinkhole-induced hazards. Several methods have been used to evaluate sinkhole risks, including destructive methods, such as Standard Penetrating Tests (SPT) and Cone Penetrating Tests (CPT), geophysical method, and sensor-based groundwater monitoring method. However, few studies are available for comprehensive understanding of spatiotemporal sinkhole mechanism by combining different exploration methods under realistic experimental conditions. The objective of this study is to understand spatiotemporal sinkhole mechanism, using SPT, CPT, ground penetrating radar …

A Sustainability-Based Project Selection Algorithm: Socio-Technical-Economic Project Selection (Steps) Algorithm, Bharathi Bhattu

Dissertations, Master's Theses and Master's Reports

Multi-dimensional aspects play a vital role in the task of project-decision making. Environmental effects are to be considered in addition to other technical and non-technical aspects in order to avoid undue environmental damage. This current work introduces a new decision-making algorithm (Socio-Technical-Economic Project Selection or STEPS) that is demonstrated with the use of RCA (recycled concrete aggregate) as riprap for slope stabilization and erosion control which leaches chemical arsenic when in contact with water. Arsenic has long been recognized for its lethal properties. The main intention of introducing this new algorithm is to use sustainability concepts of social, technical, and …

Geotechnical State-Of-The-Art In Guatemala -- Ground Stabilization, Fernando Rafael Callejas Benitez

Doctoral Dissertations

"History provides an understanding of the present and in a way, a guide for the future. The state-of-the-art is often referred to as a snapshot of the most significant works and contributions made in a field of study; In this case the focus is on Guatemalan geotechnical engineering. This study presents a comprehensive description of the different events that impulse geotechnical engineering in Guatemala.

As part of the description of the state-of-the-practice an investigation of the different human (engineers/contractors) and physical resources (laboratories/field equipment) and their capabilities are presented. An overview of the civil engineering programs is presented. Then, the …

Comparative Analysis Of Buckling-Restrained Braced Frames In Eccentric Configuration (Brbf-Es) And Eccentrically Braced Frames (Ebfs), Peter T. Vayda

Civil Engineering Undergraduate Honors Theses

Continuing on the findings of “Using Buckling-Restrained Braced Frames in Eccentric Configuration,” by Dr. Gary S. Prinz, P.E., which determined that, from a performance standpoint, BRBF-Es could be a viable alternative for EBFs. A comparative analysis was conducted on the design procedures and initial cost estimates of BRBF-Es and EBFs. Upon designing four 12-Story buildings (two BRBF-Es and two EBFs), it was determined that BRBF-Es were easier to design due to the statically determinant system. The initial costs estimates of BRBF-Es; however, ranged upwards of 30% more cost than EBFs. Therefore, the initial investment of more intensive structural engineering design …

Hydrocompaction Considerations In Sinkhole Investigations, Edward D. Zisman P.E., P.G., Stephen West

Sinkhole Conference 2015

The cause of ground settlement is a significant concern in sinkhole investigations where the potential for shallow and deep-seated instability in the subsurface is a major focus of the investigation. Complicating the investigation is the occurrence of hydrocompaction of surficial soils caused by introduction of large amounts of surface water particularly from improper maintenance of rainfall runoff. This condition is usually followed by the subsequent loss of soil moisture during dry periods. This manuscript will discuss how hydrocompaction plays a role in the analysis of settlement in the investigation of sinkhole loss and how one can distinguish between hydrocompaction settlement …

Predicting Compaction Grout Quantities In Sinkhole Remediation, Edward D. Zisman P.E., P.G.

Sinkhole Conference 2015

Predicting the required quantity of grout needed to remediate a sinkhole-damaged home is a challenging task that involves significant amounts of uncertainty. The difficulty arises from the limited amount of subsurface information that is available to make subsurface predictions particularly in complex karst environments. In typical sinkhole investigations, our understanding of the subsurface is limited by the three to four data points (borings) that provide a small window into actual subsurface conditions. This information is normally obtained from borings and from information inferred by geophysical surveys. In many cases, the information is not sufficient to make accurate predictions of grout …

Monitoring The Threat Of Sinkhole Formation Under A Portion Of Us 18 In Cerro Gordo County, Iowa Using Tdr Measurements, Kevin O'Connor, Matthew Trainum

Sinkhole Conference 2015

Sinkhole formation is a common occurrence in northeast Iowa, and U.S. 18 in Cerro Gordo County was constructed over an area where sinkhole formation had only been locally known. It had not been recorded or identified in the Iowa DNR database at the time. Since 2004, sinkholes have developed along the right of way. Geophysical surveys contributed very little in the identifying the cause. However a Soil Survey (drilling program) identified numerous voids within carbonate bedrock. The soil borings indicated that shale overlying the carbonate rock has been removed/eroded, and resulted in the development of a karst subsurface through the …

Spatial Variability Of Subsurface Soil Conditions Causing Roadway Settlements, Ömer Bilgin, Kevin Arens, Mark Salveter, Alexander Dettloff

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Settlement of problematic soils constituting the roadway subgrade may result in pavement distress and structural failure, requiring periodic pavement patching and resurfacing. Many of these problems occur as a result of the settlement of soft cohesive and organic soils. Due to the extent of roadway projects and the limited frequency of boring locations, spatial variability of subsurface soil conditions, and sometimes due to an inadequate extent of exploration, these problematic soils may not be identified suitably during subsurface explorations. An extensive subsurface exploration program was implemented for detailed characterization of subsurface conditions for a relatively short section of an existing …

Caracterización De Las Propiedades Indices De Los Flujos De Lodos En 3 Km2 De La Ladera Oriental De La Ciudad De Medellín, Juan Camilo Viviescas, Juan Pablo Osorio

Conference papers

La caracterización de las propiedades índices de los geomateriales es una de las labores más importantes en la ingeniería geotécnica, al ser estos un insumo fundamental para la identificación y determinación de propiedades geomecánicas de los suelos. Las principales propiedades índices estudiadas en la geotecnia son el contenido de agua, los límites de Atterberg, la granulometría, el peso unitario y la gravedad específica, las cuales son la base para clasificación de suelos. En este artículo se presenta el análisis estadístico de las propiedades índices de suelos tipo flujo de lodos de la ladera oriental de Medellín, a partir del análisis …

Propiedades Geotécnicas De La Turba Intervenida Antrópicamente, Juan Pablo Osorio

Conference papers

La intervención antrópica en turberas genera cambios significativos en las propiedades geotécnicas de un material orgánico, altamente compresible y con baja resistencia al esfuerzo cortante. Existen diferentes formas de intervención, dependiendo de las tradiciones de cada lugar. Sin embargo, los procesos de intervención más comunes son la precarga por medio de terraplenes y el drenaje, las cuales generan una reducción en el contenido de humedad, la compresibilidad y la permeabilidad, así como un incremento en la resistencia al esfuerzo cortante. En el presente artículo, se discute el efecto de la intervención antrópica en las propiedades geotécnicas de las turbas, a …

Role Of Soil Parameters On Loading Of Buried Structures, Xiao Zhang, Mark D. Bowman, Rafael R. Armendariz Briones

The Summer Undergraduate Research Fellowship (SURF) Symposium

Load rating is the process to evaluate and explore the structural capacity of bridges as much as possible within safety range. As a balance between economy and safety, proper load ratings save money and keep public safe. Knowing the contribution and interaction of each different soil parameter on the loading can significantly reduce the amount of work when load rating those structures. However, for buried structures without plans, such contribution or interaction is never known. This parametric study explores how much each soil parameter of three types of soils can affect the loading of buried structures without plans. An existing …

Analysis Of Sedimentation Characteristics Of Dredge Sediment Used In Coastal Restoration And Marsh Creation Projects, Christine M. Mebust

LSU New Orleans Theses and Dissertations

There is a demand to reestablish a healthy coastal ecosystem by rebuilding wetlands with river diversion or dredged sediments in coastal Louisiana. Land building projects using dredged sediments from adjacent canals and river beds, can be used to protect the coastal properties and infrastructure systems from flood and storm surges. To predict the sediment’s long term behavior, math models require input parameters based on sediment engineering properties and material characteristics. Proper characterization is critical for accurate design of coastal restoration projects. The dredge material sedimentation characteristics and their effects on the settlement rate of suspended solid particles and underlying foundation …

Feasibility Study: The Evaluation Of Polymer Coatings To Prevent Weathering Of Weak Rocks, Lauren Distler

Senior Honors Projects, 2010-2019

The weathering and erosion of weak rocks along roadways can cause dangerous and potentially fatal rockfalls.   Various slope stabilization methods exist, but each presents a set of challenges and trade-offs.   The focus of the project is to understand the feasibility of utilizing of a polymerbased slope stabilization technique. Rock samples were collected along US Route 33 in Virginia and West Virginia, and preliminary tests were conducted to evaluate the absorption of water (% mass) and durability. The study evaluates three polymer options in regard to the following criteria: adhesion to rock, layer thickness, semi-permeability, insolubility, and non-toxicity. The polymer selection …

Amount Of Uncertainty In The Methods Utilized To Design Drilled Shaft Foundations, Morgan Race

Graduate Theses and Dissertations

In 2001, load and resistance factor design (LRFD) for deep foundations was required by the American Association of State Highway and Transportation Officials (AASHTO). Following implementation of LRFD, localized calibration of resistance factors using data from the states of Colorado, Florida, Kansas, Louisiana/Mississippi, Missouri allowed these states to utilize higher resistance factors during design. However, characterizing the uncertainty in the design of DSF, regarding the geotechnical investigation methods and the utilized software programs, higher values of resistance factors may be calibrated to more efficiently design DSF with the same level of reliability.

Three test sites within the state of Arkansas, …

Alkali-Silica Reaction Mitigation Using High Volume Class C Fly Ash, Sydney Marie Dickson

Civil Engineering Undergraduate Honors Theses

Fly ash is the residue produced from coal combustion in electric generating plants. There are two types of fly ash, Class C and Class F. Approximately 40 percent of fly ash generated from coal combustion can be used as a partial replacement of cement in concrete. Incorporating fly ash improves concrete properties and extends its service life. Alkali-silica reaction (ASR) is an expansive reaction between reactive silica typically found in aggregates (rock and sand) and alkalis in cement. This reaction results in the formation of a gel that absorbs water and swells, which exerts an internal pressure in concrete. This …

A Study Of The Influence Of Particle Gradation In Bonded Assemblies, Matthew P. Watters

Civil Engineering Undergraduate Honors Theses

The discrete element method (DEM) has been used extensively to study soil, rock, and masonry behavior because of its ability to model the materials as individual particles or bonded clumps of particles. DEM allows for examination of the macro- and micro-scale response and provides a means to study the fundamental material behavior, but it is still considered computationally expensive in relation to other methods. To lower computational costs, the smallest particle sizes are often considered negligible and are left out of the model. Additionally, rock or intact materials are often modeled as a bonded assembly of uniform spheres. To date, …

Prediction Of Shear Strength And Ductility Of Cyclically Loaded Reinforced Concrete Columns Using Artificial Intelligence, Nicholas Gordon

UNLV Theses, Dissertations, Professional Papers, and Capstones

The shear strength and deformation capacities of reinforced concrete (RC) columns are governed by a multitude of variables related to material properties of the steel and concrete used in the design and construction of the columns. Predicting performance of RC columns using design variables is a complex, non-linear problem. The prediction of shear strength and ductility for these types of structural members has historically been performed using empirically or semi-empirically derived formulae based on experimental results. The introduction of cyclical lateral loading, such as the forces imposed on a structure during an earthquake, can result in severe degradation of shear …

Senior Design: Proposed Stem Academic Building, Middlesex Community College, Senior Design Class

Civil Engineering Student Work

2015 Civil Engineering Senior Design Project.

A proposal for a new STEM building to be constructed on the Middlesex Community College.

Completed by:

• Abdullah Al Bakri
• Ryan Benoit
• Brittany Brown
• Michael Buraczynski
• Samuel Colangelo
• Joseph Connolly
• Kyle Elmy
• Michael Fischer
• Victor Goitia Jurado
• Michael Hanley
• Andrew Malian
• Michael Mathews
• Dionys Quezada
• Katie Rougeot
• Jacob Santos
• Isadora Sartor
• Vega Yerko

Soil-Bentonite Slurry Trench Cutoff Wall Final Design Report, Ushma Manandhar, Brian Ward, Tyler Zbytek

NSF Soil-Bentonite Slurry Trench Cutoff Wall Documents

Technical report includes background information on the project, site borings, several laboratory tests that were performed, and designs for the cutoff wall.

National Science Foundation Soil-Bentonite Cutoff Wall Award Abstract, Jeffrey C. Evans, Michael A. Malusis, Robert W. Jacob

NSF Soil-Bentonite Slurry Trench Cutoff Wall Documents

This award abstract describes the purpose of constructing a soil-bentonite cutoff wall as well as the tests that were performed to analyze the performance of the wall.

Commercialization Of A Small, Lightweight, Low-Cost Seismic Borehole Receiver, Rachel Adams

Theses and Dissertations--Civil Engineering

Herein, conceptualization of a recently patented seismic borehole receiver and its components is developed for commercialization. The device is significantly cheaper, lighter, and smaller than existing technologies on the market. Additionally, it has the potential to achieve better seismic readings than its competitors via patented sensor-to-borehole coupling mechanism. It is the hope that the commercialization of this device will not only provide a more affordable alternative to engineers and geophysicists in the existing market, but the significant cost difference may open new seismic measurement opportunities in the developing world. Its compact size and light weight will increase mobility, allowing investigators …

Evaluation Of Strength And Hydraulic Properties Of Buried Pipe Systems Used For Stormwater Harvesting, Mario Samson Mena

Electronic Theses and Dissertations

Water scarcity has been identified as a global issue. Both water harvesting and an efficient water piping system are some of the important factors to meet the water demand. In this study, high-density polyethylene (HDPE) pipes used as an underground storage was evaluated and a Microsoft EXCEL based model was developed, called PIPE-R Model. To study the structural integrity of the pipes, laboratory and field testing were conducted. For the water harvesting, UCF Stormwater Management Academy designed an EXCEL based model to simulate the system's performance to store and redistribute water for an average year. The purpose of PIPE-R Model …

Damage Detection Methodologies For Structural Health Monitoring Of Thin-Walled Pressure Vessels, Arturo Modesto

Electronic Theses and Dissertations

There is a need in exploring structural health monitoring technologies for the composite structures particularly aged Composite Overwrapped Pressure Vessels (COPVs) for the current and future implementation of COPVs for space missions. In this study, the research was conducted in collaboration with NASA Kennedy Space Center and also NASA Marshall Space and Flight Center engineers. COPVs have been used to store inert gases like helium (for propulsion) and nitrogen (for life support) under varying degrees of pressure onboard the orbiter since the beginning of the Space Shuttle Program. After the Columbia accident, the COPVs were re-examined and different studies (e.g. …

Mechanical Behavior Of Grouted Sands, Ryan C. Ortiz

Theses and Dissertations--Civil Engineering

Grouting techniques have been in used for many years, but several new grout materials have surfaced in recent decades that have re-defined the boundaries of the limitations of grouting programs. Typically these applications are used for seepage control in earthen impoundments, but strength of these earthen impoundments should be considered where there is potential for movement in the grouted soil mass. This study investigated initial conditions that could affect grout application effectiveness. The initial conditions in question were soil grain size and in situ moisture content. Two grouts were used, ultrafine and acrylate, and variations in pure grout properties were …

Deformation-Based Excavation Support System Design Method, Sekyi K. Intsiful

Theses and Dissertations--Civil Engineering

Development in urban areas around the world has steadily increased in recent years. This rapid development has not been matched by the ever decreasing open space commonly associated with urban centers. Vertical construction, thus, lends itself a very useful solution to this problem. Deep excavation is often required for urban construction. Unfortunately, the ground movements associated with deep excavation can result in damage to adjacent buildings. Thus, it is critically important to accurately predict the damage potential of nearby deep excavations and designing adequate support systems.

A new design method is proposed, as an attempt, to address the problem. The …

Prediction Of Strength And Shear Modulus Of Compacted Clays Within An Unsaturated Critical State Framework, Corrie Walton-Macaulay

Theses and Dissertations--Civil Engineering

The objective of this research study is to determine whether the soil stiffness, from which the small-strain shear modulus is determined, can be used to predict the shearing resistance of compacted clay soil, which are invariably under conditions of partial saturation. The research program developed for this objective included three major soil testing programs of matric suction, shear modulus, and strength.

A method to estimate matric suction of field compacted clay soil was presented and it is based on the quantified effect of change in initial void ratio on the soil water characteristic behaviors. With the use of a non-nuclear …

Mechanical Characteristics Of Organically Modified Fly Ash-Kaolinite Mixtures, Xin Kang

Doctoral Dissertations

"Fly ash is a hazardous waste material to the environment. Beneficial reuse of fly ash, however, brings economic and environmental benefits, i.e., decreases the cost of disposal, reduces greenhouse gas emission, and improves mechanical properties of construction materials. Due to the lack of pozzolanic properties, the reuse rate of Class F fly ash in geotechnical engineering is relatively low (ACAA 2013). In order to promote the effectiveness and sustainability of high volume reuse of class F fly ash in geotechnical engineering, biopolymers (Chitosan, and Xanthan gum) and synthetic polymers (Polyethylene Oxide, PEO) were used instead of the traditional stabilizers to …