Civil Engineering Commons^™

The Use Of 2d Plastic Grating For Surface Profile And Dimension Manufacture Product Measurements By Using Ndt Moiré Technique, Retno Wigajatri P., Dini Andiani

Makara Journal of Technology

The Use of 2D Plastic Grating for Surface Profile and Dimension Manufacture Product Measurements by Using NDT Moiré Technique. Research of measuring the shape and dimension of object using the moiré technique have been done. Measurement have been made by observing the moiré space as a result of interaction between grating and its shadow casted on the object’s surface caused by the projector lamp with CCD camera. The acquired data was further processed by way of off-line. By successive phase shifts that is π/2, π dan 3π/2 towards the table tennis ball at the distance of 48 cm from the …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: I. Swamp Water, Sulistyoweni Widanarko, Henki W. Ashadi, Andri Krisnadi Wicaksono

Makara Journal of Technology

Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO4 2-, Cl-, NO3 -. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: Ii. Swamp Sludges, Henki W. Ashadi, Sulistyoweni Widanarko, Irma Gusniani

Makara Journal of Technology

A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO4 2-, Cl- and NO3 -. The research treatment used by emerging ST 37 and ST 60 within 60 days in ‘polluted’ sludge swamp area. Three variation of ‘polluted’ swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion …

The Effect Of Ca Content On Cao-Zeolite On Nitrogen Adsorption Capacity, Mohammad Nasikin, Tania Surya Utami, Agustina Tp Siahaan

Makara Journal of Technology

In industry, Ca zeolite is used as nitrogen selective adsorbent with the use of PSA (Pressure Swing Adsorption)/VSA (Vacuum Swing Adsorption) methods. Natural zeolite modified to be Cao-zeolite by ion exchange process using Ca(OH)2. Adsorption test was done on CaO-zeolite with different Ca concentration to understand how it’s adsorption phenomena on oxygen and nitrogen. Adsorption test has been done for CaO-zeolite with Ca concentration = 0,682%, 0,849% and 1,244% to oxygen and nitrogen with equal concentration seperately. Pressure variation has being done three times (5 minutes long each time) adsorption time to analyze the connection between adsorption time and how …

Cetane Number Booster Additive For Diesel Fuel Synthesized From Coconut Oil, Mohammad Nasikin, Rita Arbianti, Abdul Azis

Makara Journal of Technology

To reduce NOx, SOx, HC, and particulates that produce because of using diesel fuel, can be done by increasing cetane number. One of methods is adding an additive to diesel fuel. 2-Ethyl Hexyl Nitrate (2-EHN) is a commercial additive that an organic nitrate. Making an additive in this research is used palm oil by nitration reaction that used HNO3 and H2SO4. Result of this reaction is methyl ester nitrate that has a structure looks like 2-EHN. IR spectra from research show that methyl ester nitrate is indicated by spectrum NO2 at 1635 cm-1. This result show that methyl ester nitrate …

Analogy Method Development For Cost Estimation Of Software Design, Riyanarto Sarno, Joko Lianto Buliali, Siti Maimunah

Makara Journal of Technology

The important aspect of planning and managing software development project is to estimate the cost of a project. There are several methods for estimating the cost of a software development project, and the Analogy method is a method which gives relatively better estimates. This paper shows that the modified Analogy method selects a closer project reference, estimates more accurate project effort and cost. This study enhances the cost estimate technique by including valid and complete cost parameters, therefore the estimate of a project cost is better than the result of the standard Analogy method.

The Role Of Si3n4 Amorphous Phase In Nc-Tin/A-Si3n4 Nanocomposites In Increases The Hardness And Thermal Stability, Keba Moto

Makara Journal of Technology

The role of Si3N4 amorphous phase in nc-TiN/a-Si3N4 nanocomposites will be shown and compared with polycrystalline ZrN/Ni which has no such amorphous phase (non-composites). The presence of amorphous phase Si3N4 increases the hardness of film as well as the toughness of the bulk nanocomposites under indentation load. It has been observed that nc-TiN/a-Si3N4 nanocomposites films has higher thermal stability than ZrN/Ni polycrystalline films.

Biodiesel's Characteristics Preparation From Palm Oil, Tilani Hamid. S, Rachman Yusuf

Makara Journal of Technology

Biodiesel’s characteristics preparation from palm oil. Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester) by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH) as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio …

Development Of Hardness Measurement Procedure For Nanocomposite Nc-Tin/A-Si3n4, Keba Moto

Makara Journal of Technology

Hardness of nc-TiN/a-Si3N4 nanocomposites which was determined by using two methods of measurements i. e. depth sensing method and remaining plastic indentation area that were magnified by using SEM (Scanning Electron Microscope) lie in the good agreement. The hardness value is not influenced by the biaxial and residual compressive stress. The measurement of the biaxial stress on the substrate shows a very small value of biaxial stress as well as the constant hardness and crystallite size against annealing temperature. Therefore, the reported hardness value here is the intrinsic value that depend on its microstructure properties.

Integrating Passenger And Modulo As Learning Tools For Collaborative Engineering Education, Kalamullah Ramli, Frank Schwarz, Stefan Werner, A Halim Shamsuddin, Axel Hunger

Makara Journal of Technology

The University of Indonesia (UI), Gerhard Mercator University (GMU), the Universiti Kebangsaan Malaysia (UKM) have agreed to cooperate as partners to develop a joint bachelor (3+1) and masters (1+1) degree, and collaborate in the research fi elds of multimedia- and internet-based learning and application level active networks. This paper describes the introduction of the Offshore Project and the extending of information technology applications to the partner institutions in this international cooperation which would very much enhance the operations of the new initiative in engineering education, which could provide students in far distance with more fl exible learning environment.

Study Effect Of Salt Washing Process On Content And Iodium Stability Of Salt, Nelson Saksono

Makara Journal of Technology

Effect of Salt Washing Process on Content and Iodium Stability of Salt. Salt washing process should increase the salt quality. It should clean the salt from sludge or clay and also reduce the impurity compound such as Mg, Ca and the reductor content. The objective of these reseach is to assess the effect of washing process on the content og hygroscopic impurities compound (Ca and Mg), and reductor content of salt. The research also investigate the water absorbing, pH, KIO3 content as function of time to obtain effect of washing process on KIO3 stability in salt. The experiment result shows …

Object Classfification In Computer Vision With Discriminant Analysis, Amir Hamzahan

Makara Journal of Technology

A robotic sensor system is always supported by a computer system called ‘computer vision’. The important concept of computer vision is object classfifi cation. In this study two algorithms for object classifi cation in this system will be compared. Firstly, A simple method that do not need complex computation and that considered as an informal method is called binary tree decision structure. This method is based on modest caracteristic decriptors of an object such as vertical line, horizontal line or ellipse line. Unfortunately this method has weakness in recognize an image that contaminated by a noise. Secondly, a more formal …

Making Alloys (Ti1 - Xalx) N Using Plasma Cvd Technique From Alcl3 Powder, H2 And N2 Gas ,With Solvent Ticl4, Keba Moto

Makara Journal of Technology

The substitution of Ti atoms by Al atoms in TiN lattice sites to form (Ti1-xAlx)N is clearly demonstrated by the coatings which were deposited on steel substrate and using plasma CVD technique. The presence of Al atoms in TiN lattice site is shown by means of XRD and EDX techniques: lattice parameters decreasing of TiN as the fraction of Al increases (XRD) and precipitation of hexagonal AlN phase (XRD) as the fraction of Al exceeding 0.8 (EDX). The hardness of these coating are just around 30 GPa, which is beyond the values reported in literatures.

Effects Of 0.25 % Mo (Molybdenum) Which Is Contained In The Ductile Cast Iron On Mechanical Properties Of Austempered Ductile Iron (Adi)., Nukman Nukman, Bustanul Arifin, Bambang Sugiarto

Makara Journal of Technology

The aim of this research is to investigate the effects of 0.25 % Mo (Molybdenum) which is contained in the ductile cast iron on mechanical properties of Austempered Ductile Iron (ADI). The various temperatures and the holding times are used in the heat treatment processes. Using a given 0.25 % Mo in the ductile iron, ADI's alloyed developes a higher ultimate tensile stress value and decreases the elongation if we compare with the as cast (non alloy ductile iron). The higher impact energy value obtained at 9000 C austenization and 375o C austempering temperatures during 60 minutes holding times. The …

The Manufacturing Properties Of Galvanised Steel Sheet With Hexagonal And Tetragonal Network Of Circle Holes, Rahmat Saptono

Makara Journal of Technology

Galvanized steel sheet of 0.8 mm in thickness was drilled with circle holes of 2.5 mm diameter and spacing arranged in tetragonal and hexagonal pattern. The manufacturing properties of specimen were studied through drawing and stretching simulative test. It was concluded from the results that, at high ratio of punch to hole diameter (40/2.5), the drawing properties (LDR) of both square and hexagonal perforated sheet were slightly lower than that of solid sheet, while hexagonal perforated showing LDR somewhat higher than the square one. The stretching properties (LDH) of sheet, however, were much lower than that of solid sheet while …

Develops The Software Of Dsp Processor For The Cdma Circuitry, Arman Djohan D.

Makara Journal of Technology

This research develops the software of DSP Processor type TMS320C54X for the CDMA circuitry. This research apply two algorithms namely Mathematic Algorithm and table lookup Algorithm. From both algorithms, the research examine what algorithm have the fasted processing time and the smallest memory occupation. From the examination results the Mathematic Algorithm have 20.62 milliseconds processing time and the Table lookup algorithm have 14.08 milliseconds processing time. The Table lookup algorithm have the fastest processing time because the Matematic algorithm need the rounding process of the fi gure. Eventhough such processing time is not exceed from the 125 millisecond of delay …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Micro Hydro Power, Frederick J. Munster

Maine Collection

Micro Hydro Power

by Frederick J. Munster

Department of Economic and Community Development, August, Me. 1999 (?).

Contents: Introduction / History of Hydropower in Maine / Renewables / Why Micro Hydro / Determining Flow / Determining Head / Estimating Energy Potential / Hydro Turbines / Dams, Impoundments, Penstocks and Power Houses / Utility Interconnected Systems / Battery Charging Systems / Operation and Maintenance / Economics / Regulation of Hydro Development / For More Information / References

Incident Management In Intelligent Transportation Systems, Kaan Ozbay, Pushkin Kachroo

Electrical & Computer Engineering Faculty Research

Since the conception of Intelligent Transportation Systems (ITS) in the 1980s, many transportation researchers have also worked on the development of incident management models and integrated systems for real-time operations. ITS created the required infrastructure for collecting, processing, and managing real-time traffic data that can be used to develop on-line incident management strategies. This book provides the reader with a broad picture of the overall incident management process in the context of ITS along with a quick review of the models and systems developed by numerous researchers worldwide. This book is a direct result of the long-term incident management research …

Sliding Mode For User Equilibrium Dynamic Traffic Routing Control, Pushkin Kachroo, Kaan Ozbay

Electrical & Computer Engineering Faculty Research

Presents a solution to the user equilibrium dynamic traffic routing (DTR) problem for a point diversion case using feedback control methodology. The sliding mode control technique which is a robust control methodology applicable to nonlinear systems in canonical form is employed to solve the user equilibrium DTR problem. The canonical form for this problem is obtained by using a feedback linearization technique, and the uncertainties of the system are countered by using the sliding mode principle. Simulation results show promising results.

Flexible Low-Cost Automated Scaled Highway (Flash) Laboratory For Studies On Automated Highway Systems, Pushkin Kachroo, Kaan Ozbay, Robert G. Leonard, Cem Unsal

Electrical & Computer Engineering Faculty Research

This paper addresses the development of a flexible low-cost automated scale highway (FLASH) laboratory which is intended to serve as a catalyst for accelerating the development of many intelligent vehicle highway system (IVHS) concepts. It also highlights the significance of the laboratory for the research, evaluation, and testing of automated highway system (AHS) configurations, architectures, designs and technologies. This laboratory, using small scale standardized vehicles will serve as a test bed for the economical development and evaluation of various hardware, software, and management systems before full scale testing and deployment. The laboratory will provide the capability to test day and …

Power Shedding Experiences And Lessons In A Township, Alexander Kyaruzi

Tanzania Journal of Engineering and Technology (TJET)

This paper presents how power shedding by taking out one of the trans- former high voltage fuses causes phase imbalance. And for the same elec- nicc,l energy output generator fuel consuntption with unbalanced phases is 12.5% of The fuel consunwtion with balanced phases. Furthermore it is shown thal energy efficient lighting by use of energy efficient bulbs can reduce load shedding.

Feasibility Study Of Maine's Small Hydropower Potential, James D. Sysko

Maine Collection

Feasibility Study of Maine's Small Hydropower Potential

Prepared by James D. Sysko, Small Hydro East, for the Maine State Planning Office, Maine Office of Energy Resources, January 1989.

"This study focuses on finding potential hydropower sites of approximately 50 kw to 1000 kw in capacity."

Fundy Tidal Power Development : Preliminary Evaluation Of Its Environmental Consequences To The Resources Of The State Of Maine, Bigelow Laboratory For Ocean Sciences

Maine Collection

Fundy Tidal Power Development : Preliminary Evaluation of Its Environmental Consequences to the Resources of the State of Maine

A Report to the Maine State Planning Office by the Bigelow Laboratory for Ocean Sciences, April, 1984.

"Technical Report No. 35 - Bigelow Laboratory for Ocean Sciences, West Boothbay Harbor, Maine - A Division of Northeastern Research Foundation, Inc."

Contents: Executive Summary / Introduction / Methods / Physical and Biological Consequences / Socio-Economic Consequences / Research Needs / Bibliography / Appendix I. Written Comments on Greenberg Model

Electrical Wiring For Lower-Cost Housing, Burns E. Hegler

International Symposia on Low Cost Housing Problems

No abstract provided.