Civil and Environmental Engineering Commons^™

Condition Assessment Of Bill Emerson Memorial Cable-Stayed Bridge Under Postulated Design Earthquake, Dongming Yan, Wenjian Wang, Genda Chen, Bryan A. Hartnagel

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, a three-dimensional finite element model of the Bill Emerson Memorial cable-stayed bridge was developed and validated with the acceleration data recorded during the M4.1 earthquake of May 1, 2005, in Manila, Arkansas. The model took into account the geometric nonlinear properties associated with cable sagging and soil-foundation-structure interaction. The validated model was used to evaluate the performance of a seismic protective system, the behavior of cable-stayed spans, and the accuracy of two simplified bridge models that have been extensively used by the structural control community. The calculated natural frequencies and mode shapes correlated well with the measured …

Theory Of Breakup Of Core Fluids Surrounded By A Wetting Annulus In Sinusoidally Constricted Capillary Channels, Igor A. Beresnev, Wen Deng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Analysis of core-annular dynamics in the presence of base flow for arbitrary fluid viscosities leads to an equation describing the temporal evolution of the fluid/fluid interface. The equation follows from the conservation of mass in the "small-slope" approximation. Its useful applications occur, for example, in chemical engineering and petroleum recovery. The nonlinear equation allows inexpensive numerical analysis. For sinusoidally constricted pores, a purely geometric criterion exists that enables or prohibits the core-fluid breakup in the necks of the constrictions. The geometrically favoring condition sets up capillary-pressure gradients that ensure a continuous outflow of the core fluid from the necks into …

Integration Of Mechanistic-Empirical Pavement Design Guide Distresses With Local Performance Indices, Scott Schram, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The pavement management system (PMS) is the organizational entity within a state highway agency responsible for the condition of the pavement network. Visual distress surveys are typically combined into an index to provide an overall measure of performance. Decision makers use these familiar indices in a number of facets. A recent survey suggests every state highway agency has implemented or plans to implement the Mechanistic-Empirical Pavement Design Guide (MEPDG). As they do so, maintaining the role these local indices play is critical for upholding the system's continuity. However, using the MEPDG output directly in calculating performance indices becomes problematic because …

Control Force Estimation In Seismic Building Design, Xiaozhe Zhang, Franklin Y. Cheng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents two approaches of estimating the control force magnitude in the building structure's seismic design. One is by spectrum average in frequency domain, and the other is by nondeterministic Monte Carlo analysis in time domain. the spectrum method is proposed to find the estimation by averaging the system's frequency response with an earthquake spectrum as a weighting factor. the nondeterministic method is based on sets of potential ground motions generated numerically. the approaches are developed in the concept of performance design, with studies based on the site potential seismic hazard and presenting results at different levels of displacement …

Modeling Permanent Deformation Of Unbound Granular Materials Under Repeated Loads, Cheng Chen, Louis Ge, Jiansheng Zhang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Finite-element analysis on a pavement structure under traffic loads has been a viable option for researchers and designers in highway pavement design and analysis. Most of the constitutive drivers used were nonlinear elastic models defined by empirical resilient modulus equations. Few isotropic/kinematic hardening elastoplastic models were used but applying thousands of repeated load cycles became computationally expensive. in this paper, a cyclic plasticity model based on fuzzy plasticity theory is presented to model the long-term behavior of unbound granular materials under repeated loads. the discussion focuses on the model parameters that control long-term behavior such as elastic shakedown. the performance …

Special Issue On Modeling In Geotechnical Engineering For Design And Materials, R. A. Tarefder, D. H. Chen, Y. N. Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Finite Element Modeling Of A Field-Scale Shored Mechanically Stabilized Earth Wall, Cheng Chen, Louis Ge, Jia Sheng Zhang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The shored mechanically stabilized earth (SMSE) walls are typically used in steep terrain to allow construction of a new road or widening of an existing narrow-road by constructing the wall on the outboard of the roadway. the state-of-practice suggests a minimum bench width and MSE reinforcement length equivalent to seventy percent of the design height of the MSE wall. It has been shown recently that shorter reinforcement length is sufficient when the SMSE wall system is constructed, and the retaining benefits provided by the shoring component should be taken into consideration. in this paper, a finite element analysis is performed …

Simulation Prototyping Of An Experimental Solar House, Anna Osborne, Stuart Baur, Katie Grantham

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents a comparative analysis between an energy simulation model and an actual solar home. the case study used was the Team Missouri's 2009 Solar Decathlon entry. the home was evaluated using the predicted data developed with the use of Energy-10 Version 1.8. the software simulates the energy use performance of building strategies ranging from building envelope and system efficiency options. the performance data used was collected during the 2009 Solar Decathlon competition. Results comparing energy efficient strategies, consumption and generation are explored with future implications discussed. © 2010 by the authors.

High-Strength Selfconsolidating Concrete Girders Subjected To Elevated Compressive Fiber Stresses, Part 1: Prestress Loss And Camber Behavior, Jared E. Brewe, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The design of prestressed concrete members is restricted by the requirement that the extreme compressive fiber stress at midspan of simply supported members be less than 60% of the concrete compressive strength at release of prestressing. the purported purpose of this limit is to address serviceability performance, but it places unnecessary limits on the capability of the materials. for this research program, six prestressed concrete girders were produced with high-strength self-consolidating concrete and subjected to compressive fiber stress levels ranging from 65% to 84% of the concrete compressive strength at release of prestressing. Time dependent concrete surface strains were measured …

Variability In Resilient Modulus Of Reclaimed Asphalt Pavement As Base Layer And Its Impact On Flexible Pavement Performance, Mohamed Attia, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The use of reclaimed asphalt pavement (RAP) as a base layer is gaining popularity, but there are gaps in the literature about its material performance. One problem not well investigated is the variability in the resilient modulus (M_R) of RAP as a base layer, as compared with typical granular material, and the impact of this variability on pavement performance. Selection of one M_R value has its own variability, beyond the expected variability in the base layer _R that results from the use of aggregates with different qualities. This paper investigates the effect of three sources of variability …

Effect Of Radar-Rainfall Uncertainties On The Spatial Characterization Of Rainfall Events, Pradeep V. Mandapaka, Gabriele Villarini, Bong Chul Seo, Witold F. Krajewski

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Remotely sensed precipitation products, due to their large areal coverage and high resolution, have been widely used to provide information on the spatiotemporal structure of rainfall. However, it is well known that these precipitation products also suffer from large uncertainties that originate from various sources. In this study, we selected radar-rainfall (RR) data corresponding to 10 warm season events over a 256 x 256 km² domain with a data resolution of 4 x 4 km² in space and 1 h in time. We characterized their spatial structure using correlation function, power spectrum, and moment scaling function. We then …

Bridge Lessons Learned From The Wenchuan China, Earthquake, W. Phillip Yen, Genda Chen, Mark Yashinski, Youssef M. A. Hashash, Curtis J. Holub, Kehai Wang, Xiaodong Guo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A strong earthquake of M7.9 occurred in Wenchuan County in Sichuan Province, China, on May 12, 2008. This paper presents the field observations on various types of bridge damages, including unseating of girders, longitudinal and transverse offset of decks, pounding at expansion joints, shear key failure, bearing displacement, column shear, and flexible cracks. Plausible causes of damages and collapses are discussed and the lessons learned from this event are briefly summarized. Some of the postearthquake temporary constructions are also reported.

Glass Fiber-Reinforced Polyurea Strengthening Of Reinforced Concrete, Courtney Elizabeth Greene

Masters Theses

"Wide varieties of concrete repair-retrofit and strengthening methods have been developed and are being widely implemented. In recent years, the need for such strengthening systems has become apparent with increasing demands on aging infrastructure. These strengthening systems need to be increasingly more adaptable, providing ease of construction as well as withstanding a variety of loading conditions and hazards. Exterior-applied fiber-reinforced polymer systems are increasingly being used to meet these demands. The research contained herein investigates the strengthening benefits and characteristics from a specific glass fiber-reinforced polyurea coating system applied externally to structures by means of spraying. This coating would allow …

Bayesian Approaches On Observational Before-After Highway Safety Analysis, Daxiao Liu

Masters Theses

"Observational before-after evaluation of roadway safety treatments effect is a necessary and challenging study area for traffic safety engineers. In decades, empirical Bayesian approach has been widely adopted among researchers in this area. In this approach, the researcher combined before period observation data with a safety performance function estimated from similar groups to estimate the expected number of crashes that would have occurred in the after period without the treatment. Comparing this estimate with the number of crashes observed in the after period, the researcher evaluated the effectiveness of the treatment. This approach accounts for well-known regression-to-the-mean effects. However, as …

Field Investigation Of Spalling In Bridge Decks With Partial-Depth Precast Concrete Panel Systems Using Non-Destructive Testing, Kandi Rebecca Wieberg

Masters Theses

"This study involved the investigation of the causes of spalling observed in several partial-depth precast prestressed bridge decks in the state of Missouri. Recently it has been observed that several bridges in Missouri with this type of construction have experienced spalling of concrete at the edges of the panels revealing an extreme condition of corrosion in the prestressing tendons, some to the point of rupture. Ground penetrating radar (GPR), which has been shown to be successful in bridge deck evaluation, was used to determine the relative condition of the prestressing tendons as well as the relative condition of the concrete …

Stability Of Streambanks Subjected To Highly Variable Streamflows: The Osage River Downstream Of Bagnell Dam, Kathryn Nicole Heinley

Masters Theses

"Streambank erosion of the Osage River downstream of Bagnell Dam is naturally-occurring; however, it may be significantly worsened due to releases made from the dam to generate hydropower. In this study, six typical outflow release patterns from Bagnell Dam were evaluated to determine their effects, if any, on the stability and the rate and amount of erosion of the banks of the Osage River.

The Bank Stability and Toe Erosion Model (BSTEM), version 5.2, was used to carry out the erosion and stability calculations. The model was validated by using data from another study and comparing the results from BSTEM …

Evaluation Of Liquefaction-Induced Lateral Spreading In The Midwest, Kermit Nathanial Applegate

Masters Theses

"The Central United States is home to several seismically active regions: the Wabash Valley Seismic Zone, the South Central Illinois Seismic Zone, and the New Madrid Seismic Zone. All three of these regions are capable of inducing large ground motion throughout the Mississippi Valley and along the eastern border of Missouri. This has been supported by many paleoseismic studies conducted throughout the region, which have identified numerous instances of liquefaction phenomena. The fluvial deposition process associated with the Mississippi river valley makes it a prime location for possible liquefaction and lateral spreading effects. However, there are few studies pertaining to …

Corrosion Resistance Of Enamel-Coated Steel Reinforcement For Concrete, Charles Robert Werner

Masters Theses

"Originally developed to enhance the bond between concrete and steel, reactive enamel coatings have shown great promise in protecting steel from corrosive environments. However, the corrosion resistance of the material has not yet been tested beyond 40 days. Moreover, when the material was tested, it was applied to smooth steel pins, not deformed steel bars which are commonly used in reinforced concrete structures. Therefore, this study focused on the corrosion resistance of three different enamel coatings, along with a standard epoxy coating, each of which were applied to both smooth and deformed steel bars and included both short-term and long-term …

The Placement Of Remediation Amendments Into Contaminated Sediments Via Waterjet Technologies, Gavin Hunter Ray Risley

Masters Theses

"The use of amendments to perform in situ remediation of contaminated sediments is a technique that is relatively mature. The need exists to develop a method of amendment delivery that will efficiently place the amendments into the contaminated zone at depth with minimal impacts to the benthic communities and contaminant resuspension. Waterjets have been used for hundreds of years as an excavation, cutting, and cleaning tool, but they can also be used to inject remediation amendments into contaminated sediments if setup properly. In order to test this concept, a waterjet amendment injection system and nozzle have been developed and tested. …

Microalgal Bioremediation Of Nutrients In Wastewater And Carbon Dioxide In Flue Gas, Anand Murali Narasimhan

Masters Theses

"Microalgae are potential biofuel feedstocks that can provide solutions to the twin challenges of energy security and environmental pollution. They have great potential for the removal of excess nitrogen and phosphorus from wastewater including the farm runoff. They can capture carbon dioxide in the flue gas from coal fired power plants thereby reducing greenhouse gas and also producing algal biomass, which can be converted into biofuel. In this study, the nutrient consumption of Scenedesmus algae was investigated in a batch culture and the biomass yield was determined. Algae were able to utilize carbon in the form of soluble carbonates which …

Crack Detectability And Durability Of Coaxial Cable Sensors In Reinforced Concrete Bridge Applications, Genda Chen, Ryan D. Mcdaniel, Michael A. Brower, David Pommerenke

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The working mechanism and the measurement principle of topology-based crack sensors made of coaxial cables are briefly reviewed. The sensitivity, spatial resolution, and ruggedness of two coaxial cable sensors, respectively made of rubber and Teflon dielectric materials, were compared and validated with laboratory testing of a 4/5-scale, T-shaped, reinforced concrete beam-column specimen. Two Teflon sensors were installed on one of the solid decks of a three-span continuous highway bridge to investigate their durability and measurement repeatability. Laboratory tests indicated that both types of sensors have high sensitivity, but the Teflon sensor has a higher spatial resolution and a negligible spillover …

Determining The R Values For 12 Inch Deep Z-Purlins And Girts With Through-Fastened Panels Under Suction Loading, Kaye Dee Wibbenmeyer

Masters Theses

"Designing purlins for roof systems attached to through-fastened panels has been a subject well researched in the past. The current design specification uses a simplified approach to the designing of these members where the fully braced moment capacity of such members is multiplied by a reduction factor, commonly referred to as the R-value. This value represents the point in between the fully braced and fully unbraced member behavior. However, the current AISI Specification, S100, only contains R-values for purlins and girts up to 11.5 inches in depth. Since manufacturers are now rolling sections up to 12 inches deep, two confirmatory …

Nonlinear Finite Element Formulation Of The Soil Structure Interaction Through Two Parameter Foundation Model, Taraka Ravi Shankar Mullapudi

Masters Theses

"The response of shallow and raft foundations is having a significant importance due to its complex behavior because of the semi-infinite soil media. Winkler's model is the simplest model to deal with the structure and soil. The Winkler model represents the foundation reaction as proportional to the soil displacement at a particular point, which results in the elasticity of the soil being the only parameter in consideration. But in reality the soil cohesiveness is having a significant contribution in soil structure interaction, and therefore the consideration of coupling effects of Winkler springs need to be accounted. Most of the existing …

The Effectiveness Of The Natural Resource Conservation Service (Nrcs) And Huff Rainfall Distribution Methods For Use In Detention Basin Design, Todd Wayne Dablemont

Masters Theses

"This thesis focuses on the effectiveness of the NRCS and Huff rainfall distribution methods for use in detention basin design. This study required the use of HEC-HMS, hydrologic modeling software, in order to analyze the distribution methods. Three separate detention basins and their watersheds were modeled for this study. The watersheds were analyzed for both undeveloped and developed conditions. The parameters analyzed include detention basin inflow, detention basin outflow, watershed peak discharge, and detention basin storage capacity. The determination of detention basin effectiveness was based upon these parameters. The NRCS distribution method is widely used; however, many who use it …

Calibration Of Resistance Factors For Axial Capacity Of Driven Pile Into Missouri Soil, Mulugeta Abay Kebede

Masters Theses

"Over the past two decades the load resistance factor design (LRFD) has been accepted by the American Association for Transportation and Highway Officials (AASHTO) for the design of bridges. This approach is now gaining widespread popularity in the United States for substructure bridge design, including the design of driven pile foundations, as the states calibrate the geotechnical resistance factors for local geological conditions and practices. This study presents the geotechnical resistance factors calibrated for axially driven pile using the first-order reliability method (FORM) for the target reliability index of 2.33 and 3.0 based on 64 end-of-drives (EOD) and 22 beginning-of …

Experimental And Modeling Comparison Of Modular Photovoltaic-Thermal Solar Panels, Nicole C. Annis

Masters Theses

"Three different prototype photovoltaic-thermal panels using water as the cooling fluid were tested simultaneously. The first two panels (Panel A and B) consisted of a highly conductive thermal sheeting and different sized copper tubing. The third panel (Panel C) consisted of copper tubing with an aluminum fin. Thermal images were used to verify the heat transfer across the panels and compare the amount of heat radiating off the back of the photovoltaic-thermal panels versus the standard photovoltaic paneleaf Three A type panels were thermally connected in series. Three photovoltaic panels were also tested for an electrical comparison. The purpose of …

Innovative Concrete Bridging Systems For Pedestrian Bridges: Implementation And Monitoring, Kurt Edward Bloch

Masters Theses

"Two precast, prestressed pedestrian bridges were designed for rapid construction in Rolla, MO, utilizing high-strength concrete (HSC) and high-strength self-consolidating concrete (HS-SCC) with a target 28 day compressive strength of 68.9 MPa (10,000 psi) and release compressive strength of 24.1 MPa (3,500 psi). In addition, a glass fiber reinforced polymer (GFRP) bar reinforced deck panel system was utilized in one of the two deck panels on each bridge.

Material properties were tested for compression, elastic modulus, modulus of rupture, splitting tensile strength, creep, and shrinkage following ASTM standards. Instrumentation systems within the spandrel beams and precast deck panels were implemented …

Analysis Of Nationwide Intercity Travel Demand On The Us Transportation Network, Tao Li

Masters Theses

"In this thesis, three issues about the intercity travel demand on the US transportation network are addressed. The final one is the estimation of the domestic passengers' delay cost. A scheme is designed by assuming that costs incurred by flight delays relative to the original flight schedules are imposed at passengers' final destination airports. It is applied to estimate the total domestic delay cost of year 2007 and reasonable results arc obtained. The second one is the air travel demand estimation. Two route-based optimization models are proposed to estimate the travel demand based on available data. It is shown that …

Evaluation Of Variable Speed Limits Using A Genetic Algorithm Approach To Calibrate A Vissim Model, Brian Joseph Schaefer

Masters Theses

"The variable speed limit (VSL) system has been adopted on more and more roadways across the globe as an engineering tool for controlling traffic flow, particularly during congestion situations. An important and fundamental question raised among traffic engineers is: Are the costs of installing and operating variable speed limits really justified? In order to answer this question, this thesis measures the effectiveness of the VSL system applying the VISSIM microscopic simulation model to a non-recurrent congestion situation. For the analysis, a section of interstate was modeled in VISSIM and calibrated so that the simulated results closely reproduce the observed data …

Behavior Of Externally Bonded Fiber Reinforced Polymer Systems For Strengthening Concrete Girders In Shear, Michael Shawn Murphy

Doctoral Dissertations

"Deficiencies in shear resistance are a primary concern in concrete members due to the sudden and unpredictable nature of shear failures. Shear deficiencies in concrete structures can arise due to improper design, long-term deterioration, man-made damages, increases in loads, or as a result of over strengthening in flexure. A number of shear strengthening techniques offer a cost effective means for restoring or enhancing the shear capacity of a concrete member. The use of externally bonded fiber reinforced polymers (FRP) is one such technique that has gained recent recognition for its high strength-to-weight ratio and simplicity of application. The development of …