Civil and Environmental Engineering Commons^™

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Exploration Of The Sludge Biodiesel Pathway, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Wastewater sludge is an overlooked source of fat, oil, and grease (FOG) that could be converted into biodiesel. The United States produces about 8 million tons of sludge per year. The disposal cost for this amount of sludge is about 2 billion US dollars. The widespread availability and low cost of sludge compared to other biodiesel raw materials make it an economical choice for a renewable fuel. Using sludge as a raw material can produce 25 to 30 mg per gram of fatty acid methyl ester (FAME); the main component of biodiesel. Sludge biodiesel has the potential of transforming a …

Damage Evolution And High-Rate Response Of High-Strength Concrete Under Triaxial Loading, Brett Williams

Mechanical Engineering Research Theses and Dissertations

The research presented in this study focuses on understanding fundamental mechanisms that drive material response under dynamic loading conditions. The objectives of the research were to: (1) to understand damage initiation and propagation in the bulk geomaterial under a variety of loading conditions and (2) to systematically investigate the strain rate effects on the triaxial compressive response of cementitious materials through the development of an innovative, first of its kind large-diameter (50 mm) triaxial Kolsky bar system.

The triaxial compressive response of high-strength concrete is needed to understand pressure-dependent material behavior, which is important for modeling extreme loading events. However, …

Experimental Study Of Hollow-Core Slab Containing Waste Pet Bottles, Mulia Orientilize, Josia Irwan Rastandi, R. M. Dimas Aries C., Marsha Niken P., Krisna Adi S.S., Abimantrana Abimantrana

Makara Journal of Technology

This study investigated the utilization of plastic-waste concrete as an effort to reduce urban waste problems. The waste plastic bottles were utilized to form the hollows of the hollow-core slabs (HCSs). The bottles were made of polyethylene terephthalate (PET). As a part of green research to reuse waste material, shredded PET was also added to the concrete mixture to improve the HCS strength. The cast-in-site HCS could be constructed without any difficulties. Three parameters were investigated: the effects of void content, shredded PET content, and steel-fiber (SF) content on the HCS ultimate bending capacity (Mu). Fifteen specimens were tested under …

Improving The Intellectual And Social Development Of Children With Autism: Design Of A Training Center For Autism, Hasti Jalalian

Makara Journal of Technology

Research on the relationship between the role of architecture and the psychology of children with autism, which indicates that appropriate environments for these children can have a significant effect on their healthcare process, has been recently conducted. However, statistics show that autism spectrum disorders are pervasive, and its extent in Iran has been increasing. Moreover, centers that are specifically designed for children with autism are limited, and paradigms are made without considering the mood of these children. Given the role of architecture in designing a suitable space for these children, an investigation that can identify the specific requirements of these …

Numerical Study Of A Buckling Restrained Brace (Brb) In Steel Structures And Comparison With A Convergent Ordinary Brace (Ocb) Under Static And Dynamic Loading, Fatemeh Habibpour

Makara Journal of Technology

Bulk metallic glass (BMG) has good mechanical strength, high hardness, wear resistance, and corrosion resistance with promising application in various industries. However, for the industrial production of BMG, the main issue is how to overcome limitations of joining with other materials. The present study focuses on solder processing at low operating temperature to avoid exceeding the recrystallization temperature. A feasible joining process for BMG was developed using lead-free solders. The BMG surface is pre-plated with copper, nickel, or titanium as a wetting layer. The reaction temperature is set between the glass transition temperature of BMG and the melting point of …

Analysis Of The Interfacial Reaction Between Bulk Metallic Glass Coated Copper, Nickel, And Titanium With Lead-Free Solders, Andromeda Dwi Laksono, Yee-Wen Yen, Rifqi Aulia Tanjung, Teodoro A. Amatosa, Ruki Harwahyu

Makara Journal of Technology

Bulk metallic glass (BMG) has good mechanical strength, high hardness, wear resistance, and corrosion resistance with promising application in various industries. However, for the industrial production of BMG, the main issue is how to overcome limitations of joining with other materials. The present study focuses on solder processing at low operating temperature to avoid exceeding the recrystallization temperature. A feasible joining process for BMG was developed using lead-free solders. The BMG surface is pre-plated with copper, nickel, or titanium as a wetting layer. The reaction temperature is set between the glass transition temperature of BMG and the melting point of …

Design Of Ac Microgrid Topology With Photovoltaic Uncertainties In A Rural Village, Vannak Vai

Makara Journal of Technology

Energy needs are increasing day by day, especially for developing countries, due to population growth and changing lifestyles. A suitable microgrid topology with renewable energy integration is considered to fulfill the people and society’s needs. This paper focuses on the design of AC microgrid topology for a nonelectrified village with the integration of PV uncertainties in both sitting and sizing. The development of an optimal algorithm based on the conductor use minimization and unbalanced load improvement is proposed. The shortest path is proposed to search for the minimum conductor use. Then, the algorithm for improving the unbalanced load with two …

Mean-Shift Object Tracking Algorithm With Systematic Sampling Technique, Yoanes Bandung, Aris Ardiansyah

Makara Journal of Technology

Mean shift is a fast object tracking algorithm that only considers pixels in an object area, hence its relatively small computational load. This algorithm is suitable for use in real-time conditions in terms of execution time. The use of histograms causes this algorithm to be relatively resistant to rotation and changes in object size. However, its resistance to lighting changes is not optimal. This study aims to improve the performance of the algorithm under lighting changes and reduce its processing time. The proposed technique involves the use of sampling techniques to reduce the number of iterations, optimization of candidate search …

Analysis Of Correlation And Mapping Of Chlorophyll-A Concentrations And Sea Surface Temperatures In Coastal Areas Based On Terra Modis Satellite Image Data, Hendrata Wibisana, Bangun Muljo Sukotjo, Umboro Lasminto

Makara Journal of Technology

Ecosystems in aquatic environments are distinct from ecosystems on land. Changes that occur in ecosystems in aquatic environments affect the lives of biota in these waters, including the fish used as a food source in fishing communities in coastal areas. This study aims to determine the role of remote sensing in mapping and analyzing the relationship between the parameters of sea surface temperature and chlorophyll-a concentrations on the coast. The correlation of sea surface temperature with chlorophyll-a concentrations is modeled via linear regression. An analysis of variance test is performed to establish the suitability of the temperature data for the …

The Role Of Rejuvenators In Embedded Damage Healing For Asphalt Pavement, Shi Xu, Xueyan Liu, Amir Tabakovic, P Lin, Y Zhang, S Nahar, B J. Lommerts, Erik Schlangen

Articles

Rejuvenator encapsulation technique showed great potential for extrinsic asphalt pavement damage healing. Once the capsules are embedded within asphalt pavement, the healing is activated on-demand via progressing microcrack. When the microcrack encounters the capsule, the fracture energy at the tip opens the capsule and releases the rejuvenator. Then the released rejuvenator wets the crack surfaces, diffuses into and softens the aged bitumen, allowing two broken edges to come in the contact, preventing further asphalt pavement deterioration. The quality and speed of the damage repair process strongly depend on the quality of rejuvenator, thus it is important to choose a proper …

The Effect Of Cement And Blast Furnace Slag Characteristics On Expansion Of Heat-Cured Mortar Specimens, Jair G. Burgos

USF Tampa Graduate Theses and Dissertations

Delayed ettringite formation (DEF) is a durability issue that typically occurs in concrete exposed to high temperatures at an early age such as precast elements and massive concrete structural elements. There are many advantages to precast concrete such as its quality control, better safety control, and reusable forms, which make them cheaper than casting on site [1]. Heat curing of precast concrete is conducted to obtain high early-strength. However, in doing so, durability issues can arise in the form of internal sulfate attack also known as DEF, if the internal temperature of concrete exceeds 70°C. Past this threshold, ettringite decomposes …

Comparing The Environmental Impacts Of Using Mass Timber And Structural Steel, Khang Hoang Nguyen, Steelee Knight Morgan

Construction Management

Although mass timber has seen a gradual rise in demand in the past, there has been a lack of extensive research on the environmental impacts of using mass timber as a primary structural framing material. This paper compares structural steel, and mass timber’s total embodied carbon emissions. Accurate estimates were made using plans and specs for different projects retrieved from semi-structured interviews. The estimates were input through the EC3 Calculator to provide extensive total carbon emissions measurements between each construction material. Using structural steel framing increased the project’s overall environmental impact by roughly 84% compared to using mass timber. The …

Initial Assessment Of Liquefied Scrap Tire Concrete, Abdulkareem Kuaryouti, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

A new approach to incorporate scrap tire material into concrete was investigated, where two reclaimed waste tire components, carbon black and fuel oil, were used to replace a portion of water. The effect of “liquid tire” content to water ratios from 5-40% on an otherwise typical concrete mix were assessed, where compressive and flexural strength, flexural toughness, modulus of elasticity, and several fresh concrete properties were determined. Results were compared to typically expected results of traditional shredded tire mixes with equivalent tire content. It was found that the liquid tire mixes experienced significantly less losses of compressive strength and workability …

Structural Identification And Damage Detection In Bridges Using Wave Method And Uniform Shear Beam Models: A Feasibility Study, Mehran Rahmani, Manan Naik

Mineta Transportation Institute

This report presents a wave method to be used for the structural identification and damage detection of structural components in bridges, e.g., bridge piers. This method has proven to be promising when applied to real structures and large amplitude responses in buildings (e.g., mid-rise and high-rise buildings). This study is the first application of the method to damaged bridge structures. The bridge identification was performed using wave propagation in a simple uniform shear beam model. The method identifies a wave velocity for the structure by fitting an equivalent uniform shear beam model to the impulse response functions of the recorded …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Optimisation Of Retrofit Wall Insulation: An Irish Case Study, Rakshit D. Muddu, D M. Gowda, Anthony James Robinson, Aimee Byrne

Articles

Ireland has one of the highest rates of emissions per capita in the world and its residential sector is responsible for approximately 10% of total national CO2 emissions. Therefore, reducing the CO2 emissions in this sector will play a decisive role in achieving EU targets of reducing emissions by 40% by 2030. To better inform decisions regarding retrofit of the existing building stock, this study proposes Optimum Insulation Thicknesses (OIT) for typical walls in 25 regions in Ireland. The calculation of OIT includes annual heat energy expenditure, CO2 emissions, and material payback period. The approach taken is based on Heating …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Incorporation Of Perlite And Recycled Aggregates For Internal Concrete Curing, Yosra El Maghraby, Mohamed Nagib Abou-Zeid Prof., Mohamed Abdel-Raouf Dr.

Civil Engineering

No abstract provided.

Potential Advantages Of Basalt Frp Bars Compared To Carbon Frp Bars & Conventional Steel, Yosra El Maghraby, Mohamed Nagib Abou-Zeid Prof., Ezzeldeen Yazeed El Sayed Ahmed Prof

Civil Engineering

No abstract provided.

Experimental And Numerical Studies Of Novel Thermal Energy Storage Materials For Applications In Concrete And Energy Storage Systems, Wenyu Liao

Doctoral Dissertations

In this work, several types of novel thermal energy storage (TES) materials and composites are explored, and a series of numerical simulation models and experimental protocols are developed to evaluate the potentials of these materials to be applied in concrete, pavement, and thermal energy storage systems.

The first two types of novel TES materials/composites are at the micro-scale, which use micro diatomite (DE) and cenosphere (Ceno) as carriers of phase change material (PCM), respectively. The third type of novel TES material is at the macro-scale, utilizing lightweight sand (LWS) and lightweight coarse aggregate as carriers to load PCM. The last …

Timber Bridge Pile Splicing With Fiber Reinforced Polymer Wraps, Drew L. Damich

Graduate Theses, Dissertations, and Problem Reports (ETD)

Timber pile repair using splicing is widely used but little research has been done to determine their strength capacity after repair using this method. Current timber pile splicing mechanisms utilize various steel or wooden components. Fiber Reinforced Polymer (FRP) wraps can be utilized as replacement to conventional materials in splicing of timber piles. This study evaluated the strength capacities of traditional splicing mechanisms in relation to FRP wrap splice mechanisms. Traditional splicing mechanisms consisted of flat steel plate, C-channel steel plate, and wooden plate splices. The FRP wrap splice consisted of unidirectional glass/epoxy composite with three layers of fabric as …

Recovery Of Phosphorus From Florida Phosphatic Waste Clay, Amir Eskanlou

Graduate Theses, Dissertations, and Problem Reports (ETD)

This MS thesis examines the recovery of phosphorus (P) from Florida waste clay (WC). A comprehensive literature review revealed that: (i)-The most important values being lost to WC are P and rare earth elements (REEs). For the recovery of these values from WC, two crucial attempts are the removal of extremely fine-sized clays, followed by the recovery of phosphate content, which can pave the path for the recovery of REEs; (ii)-Any scientific/ technological solution should, at the same time, be economically and environmentally attractive to the industry. As such, moving from mostly chemical separation processes to the primarily physical/ physicochemical …

Laboratory Testing And Mechanistic Analysis Of Treated Subgrade Soils, Hari Kumar Reddy Yarrapureddi

Civil Engineering Theses

Calcium-based stabilizing agents such as cement and lime have been extensively used to improve the engineering properties of base and subgrade layers of pavement systems. Recently, polymers and chemical stabilizers have become popular due to cost efficiency, ease of application, and fast curing times. In this study, California Bearing Ratio (CBR) values of polymer and chemical treated soils were compared with the CBR values of soils treated with conventional stabilizers. Parametric sensitivity analyses was carried out on key parameters including the type of subgrade soil, stabilizing agent, stabilizing agent treatment levels, and moisture conditioning. Additionally, numerical analyses was performed to …

Bio-Binder—Innovative Asphalt Technology, Amir Tabakovic

Articles

The global road network spans 16.3 million km [1], of which 5 million km is in the EU. These road networks fulfil major economic and social goals by facilitating the movement of goods and people throughout the EU, and are therefore of the utmost importance to the economic and social life of the EU [2]. National governments invest heavily in their road networks, e.g., in 2014, EUR 53.33 billion was invested in the development and maintenance of the EU road network [3]. Each year, the world produces 1.6 trillion tonnes of asphalt [4], of which 218 million tonnes is produced …

Influence Of The Shaping Process On The Tensile Properties Of Steel Reinforcement Bars Carbon Steel Grades Bjtp24 And Bjts40, Nuraziz Handika, Ridha Amalia Idhar, Jessica Sjah, Essy Arijoeni, Elly Tjahjono

Makara Journal of Technology

According to the current applicable national standard in Indonesia, i.e. SNI 07 2529 1991, in addition to the limitation on the loading rate, the steel bar must be reduced, formed, or lathed, as part of the shaping process of samples. This study determined and compared the effect of the shaping process on the yield strength, ultimate strength, and percent elongation by conducting tensile tests of steel bar grade BJTS40, i.e. deformed bar type of steel, and grade BJTP24, i.e., plain bar type of steel. Three diameters of the deformed bar (BJTS40) and one diameter of the plain bar (BJTP24) were …

A Density Functional Theory Study On Using Montmorillonite To Reduce Air Pollution, Triati Dewi Kencana Wungu, Meqorry Yusfi, Suprijadi Suprijadi

Makara Journal of Technology

In this study, density functional theory (DFT) method is used to investigate the possibility of using a smectite clay mineral called montmorillonite (MMT) in reducing heavy metals, such as Cd, through Cd adsorption. The mechanism of Cd adsorption in MMT is observed theoretically, and the tetrahedrally isomorphic substitution on the upper layer of MMT is considered to observe the role of Al and Fe in strengthening Cd adsorption. Two types of MMT are modeled in this study: Al-MMT and Fe-MMT. The Al-MMT means that Al substitutes one atom in the upper tetrahedral layer of MMT, while Fe-MMT means that Fe …

Ionic Conductiviy Of Alginate-Nh4cl Polymer Electrolyte, Nurhasniza Mamajan Khan, Noor Saadiah Mohd Ali, Ahmad Faizrin Ahmad Fuzlin, Ahmad Salihin Samsudin

Makara Journal of Technology

This study aims to produce a solid biopolymer electrolyte (SBE) by doping ammonium chloride (NH4Cl) into alginate. Solution casting was used to prepare the alginate–NH4Cl SBE system. Electrical impedance spectroscopy was performed to analyze the electrical properties of the SBE under the applied frequency range of 50 Hz–1 MHz. The incorporation of 8 wt.% NH4Cl enhances the ionic conductivity of the SBE up to 3.18 × 10-7 S/cm at ambient room temperature. Fourier transform infrared spectroscopy shows that complexation occurs between the hydroxyl (-OH), carboxylate (COO-) and ether linkage (C-O-C) functional groups due to the formation of inter- and intra-molecular …

Use Of Viscoplastic Damper For Improving The Resistance Of Steel Frames To Blast Loading, Gholamreza Abdollahzadeh, Hadi Faghihmaleki, Hamed Hamidi Jamnani, Atefeh Ebrahimi Bardar

Makara Journal of Technology

In this paper, we evaluated the effect of viscoplastic dampers on the response of steel frames under blast loading. We used SAP2000 software and link elements to investigate the responses of nine-story steel frames with and without dampers. The proposed viscoplastic damper is a new type of viscous damper. The application of this damper is based on the availability of its constituent materials. The damper acts as a viscoelastic damper at low levels of vibration, but it acts as a combination of viscoelastic operator and metal-yielding device at extreme levels of vibration. With respect to the height of the structure, …

Influence Of Lithium Bromide On Electrical Properties In Bio-Based Polymer Electrolytes, Ahmad Faizrin Fuzlin, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

This research presents the influence of lithium bromide (LiBr) on the electrical properties of alginate in bio-based polymer electrolytes (BBPEs) system. Bio-based alginate was prepared using the solution casting technique with various LiBr compositions. The ionic conductivity and electrical properties of the prepared BBPEs samples were studied using electrical impedance spectroscopy over a frequency range of 50 Hz–1 MHz. A maximum ionic conductivity of 7.46 × 10−5 S cm-1 was obtained for a sample containing 15 wt. % lithium bromide-doped alginate BBPEs at ambient temperature (303 K). The electrical analysis revealed that the most conductive sample based on alginate-LiBr BBPEs …