Civil and Environmental Engineering Commons^™

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Ultra Low-Cycle Fatigue Behavior Comparison Between Additively Manufactured And Rolled 17-4 Ph (Aisi 630) Stainless Steels, David Gonzalez-Nino, Timothy Strasser, Gary S. Prinz

Civil Engineering Faculty Publications and Presentations

This study investigates the mechanical behavior of additively manufactured (AM) 17-4 PH (AISI 630) stainless steels and compares their behavior to traditionally produced wrought counterparts. The goal of this study is to understand the key parameters influencing AM 17-4 PH steel fatigue life under ULCF conditions and to develop simple predictive models for fatigue-life estimation in AM 17-4 steel components. In this study, both AM and traditionally produced (wrought) material samples are fatigue tested under fully reversed (R = −1) strain controlled (2–4% strain) loading and characterized using micro-hardness, x-ray diffraction, and fractography methods. Results indicate decreased fatigue life for …

Impact Of Exposure On Thin Epoxy Overlay Performance, Abul Fazal Mazumder

Dissertations

Thin epoxy overlays are used for improving the condition and extending the service life of bridge decks. The tensile bond pull-off strength, evaluated as per the ASTM C1583, is used as the performance indicator. A failure in the substrate with a tensile strength of 250 psi or greater is considered acceptable. However, the performance evaluated on in-service bridge decks shows inconsistent results. Laboratory studies by several researchers documented a distinct performance difference when the overlays are exposed to room temperatures in comparison to elevated temperatures. However, the most influential parameters such as concrete surface profile, thermal compatibility between overlay and …

Research And Applications Of Artificial Neural Network In Pavement Engineering: A State-Of-The-Art Review, Xu Yang, Jinchao Guan, Ling Ding, Zhanping You, Vincent C.S. Lee, Mohd Rosli Mohd Hasan, Xiaoyun Cheng

Michigan Tech Publications, Part 1

Given the great advancements in soft computing and data science, artificial neural network (ANN) has been explored and applied to handle complicated problems in the field of pavement engineering. This study conducted a state-of-the-art review for surveying the recent progress of ANN application at different stages of pavement engineering, including pavement design, construction, inspection and monitoring, and maintenance. This study focused on the papers published over the last three decades, especially the studies conducted since 2013. Through literature retrieval, a total of 683 papers in this field were identified, among which 143 papers were selected for an in-depth review. The …

Chitosan Graphene Composite Fabrication And Characterization For Treatment Of Harmful Algal Blooms And Toxins, Sarah Zetterholm

Master's Theses

Chitosan graphene composites were fabricated and characterized as a management strategy for harmful algal blooms (HABs) caused by various species of cyanobacteria. These chitosan graphene materials were compared to previously studied chitosan graphene-oxide composites in both material properties and HAB treatment. In previous studies, adsorption of the cyanobacteria onto the surface of the composite materials has been observed. Investigations of the pure materials for these composites are also included in this study to determine whether removal is a result of charge interactions with the composite, or as an inherent property of the graphene or graphene oxide. Initial results suggest that …

Machine Learning For High-Fidelity Prediction Of Cement Hydration Kinetics In Blended Systems, Rachel Cook, Taihao Han, Alaina Childers, Cambria Ryckman, Kamal Khayat, Hongyan Ma, Jie Huang, Aditya Kumar

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The production of ordinary Portland cement (OPC), the most broadly utilized man-made material, has been scrutinized due to its contributions to global anthropogenic CO₂ emissions. Thus -- to mitigate CO₂ emissions -- mineral additives have been promulgated as partial replacements for OPC. However, additives -- depending on their physiochemical characteristics -- can exert varying effects on OPC's hydration kinetics. Therefore -- in regards to more complex systems -- it is infeasible for semi-empirical kinetic models to reveal the underlying nonlinear composition-property (i.e., reactivity) relationships. In the past decade or so, machine learning (ML) has arisen as a promising, …

Comparison Of Concrete And Steel Jacket Methods For Reinforcing A Concrete Bridge Pier By Numerical And Experimental Studies, Hadi Faghihmaleki

Makara Journal of Technology

Various rehabilitation and strengthening procedures have been developed in recent decades. A study to determine which methods can be implemented to increase the useful life of the bridge before strengthening must be performed. In this study, the seismic behavior of a reinforced concrete bridge pier with dimension 3.5 × 3.5 m, which was reinforced by two steel and a concrete jacket, was investigated. Nonlinear geometric models and materials were analyzed to estimate the seismic parameters of the pier. Results show an increase in energy absorption, ultimate strength, and ductility for the steel jacket, as well as a greater increase in …

Effect Of Arc Plasma Sintering On The Structural And Microstructural Properties Of Fe-Cr-Ni Austenitic Stainless Steels, Parikin Parikin, M. Dani, A. Dimyati, N. D. Purnamasari, B. Sugeng, M. Panitra, A. Insani, T. H. Priyanto, S. Mustofa, Syahbuddin Syahbuddin, A. Huang

Makara Journal of Technology

X-ray diffraction techniques were performed to determine the actual crystal structure of A2 austenitic stainless steel (ASS) as-cast and A2 ASS after arc plasma sintering (APS) for 2 s. Computations were conducted on the basis of the Bragg arithmetic formula by comparing the S2 arithmetic with the interplanar spacing. The Bragg arithmetic formula is a simple series for the determination of the crystalline phase of materials based on the Miller indices of cubic shapes or other shapes. A2 ASS as-cast was identified to have a crystal structure of face-centered cubic with lattice parameter a = 3.58 Å. A similar crystal …

Trend Significance Levels Of Rain Onset And Cessation And Lengths Of The Wet And Dry Seasons In Epe, Lagos State, Nigeria, Adekunle Adedeji Alli, Olorunwa Eric Omofunmi

Makara Journal of Technology

This study aims to reduce crop failure resulting from a dry spell, which is the first occurrence of unsustainable rainfall that deceives farmers into planting. Thus, trends need to be tested using hypothesis, kurtosis, and other statistics to analyze the risks associated with unstable planting calendars and their possible mitigation strategies. The daily rainfall data from 1982 to 2018 were obtained from the archive of NASA/POWER SRB/FLASH, and the research location is Epe, Lagos State, Nigeria, which lies at latitude 6.585° N and longitude 3.962° E. Microsoft Excel was used to perform the tests. Results show that the null hypothesis …

Kinetic Modeling Study Of Laminar Burning Velocity Of Gasoline–Ethanol–Methanol Blends At Elevated Temperature And Pressure, Ahmad Syihan Auzani, Cahyo Setyo Wibowo, Riesta Anggarani, Yulianto Sulistyo Nugroho, Bambang Sugiarto

Makara Journal of Technology

Gasoline–ethanol–methanol (GEM) blends have been considered to replace pure gasoline as spark ignition engine fuel. Their physical and chemical properties and performance and emission measurements from real engines have been reported previously. However, a fundamental study that can explain the unique results of GEM compared with those of pure gasoline is lacking. This study aims to compare the laminar burning velocity of GEM blends at different mixtures, equivalence ratios, temperatures, and pressures with that of pure gasoline. A laminar flame propagation model and reaction mechanisms from the literature were were for a numerical simulation. In this study, the chemical components …

Improvement Of Electrical Properties Of Cmc-Pva Doped With Various Contents Of Lino3 As An Application For Hybrid Polymer Electrolytes, Amalia Zulkifli, Norfatihah Mazuki, Ahmad Salihin Samsudin

Makara Journal of Technology

The present work was carried out with the development of hybrid polymer electrolytes (HPEs) by using carboxymethyl cellulose (CMC)–polyvinyl alcohol (PVA) doped with different contents of lithium nitrate (LiNO3) for the determination of their structural and conduction properties. The structural analysis was conducted by using Fourier transform infra-red spectroscopy and showed the interaction between the blend host polymer and ionic dopant, which formed via the coordinating site of CMC-PVA and Li+-NO3−. The complexes of CMC-PVA doped LiNO3 led to an increment in ionic conductivity, as observed by electrical impedance spectroscopy, and the sample containing 20 wt% LiNO3 obtained the highest …

Music Information Retrieval Based On Active Frequency, Hardianto Wibowo, Wildan Suharso, Yufis Azhar, Galih Wasis Wicaksono, Agus Eko Minarno, Dani Harmanto

Makara Journal of Technology

Music is the art of combining frequencies. A balance of frequencies gives rise to a harmonious tone. Several features of music can be analyzed, and they include sociocultural background, lyrics, mood, tempo, rhythm, harmony, melody, timbre, and instrumentation. In this study, we use the frequency of instrumentation as a feature for classification because each instrument has a frequency range. To test this frequency range, we use five music genres and one music playing skill. The five genres are dangdut, electronic dance music (EDM), metal, pop/rock, and reggae. The music playing skill is acoustic. Active frequencies are tested using the k-nearest …

Predictive Delivery Man Assignment Problem Using Deep Learning, Rahmadini Payla Juarsa, Taufik Djatna

Makara Journal of Technology

Dispatching is a critical part in current online shopping. It relates to how the delivery man assignment should minimize cost along with the service from a source to an end customer with an appropriate scheduled time. The problem arises as neither enough products to deliver nor delivery men are available for dispatch, resulting in suboptimal service and a waste of money. The study aimed to formulate the cost of restaurant dispatching for inducing a deep learning-based solution with the gated recurrent unit recurrent neural network to receive hourly order data and to engage the result for near feature delivery man …

Semi Real-Time Detection Of Subsurface Consolidation Defects During Concrete Curing Stage, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Subsurface consolidation defect is a common issue in concrete pavement construction, and the hidden defects often require costly repairs after project delivery. Therefore, being able to identify this type of defect during construction will enable contractor to conduct quick repairs to avoid costly post-construction rework. In this paper a semi real-time detection approach using infrared thermography is introduced. The developed approach utilizes the hydration heat during curing time to identify the subsurface voids based on the regional temperature contrast. Experimental studies were conducted using artificial void-defect in different sizes and depths. The thermographic analysis is employed to locate the void-defects …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Corrosion Propagation Of Stainless Steel Reinforced Concrete, Nelly Sofía Orozco Martínez

USF Tampa Graduate Theses and Dissertations

Structural durability is a growing concern in global infrastructure. The infrastructure report card released by the American Society of Civil Engineers (ASCE) indicates that approximately 9.1% of the total bridges in the United States were structurally deficient in 2016. In addition, it suggests that about 40% of the total bridges in the country are now 50 years or older. This issue becomes even more critical in structures exposed to aggressive environments such as marine structures. Thus, federal and regional efforts are now being directed towards infrastructural durability improvement to improve the long-term cost-efficiency of civil infrastructure.

Corrosion prevention strategies may …

Atomistic Thermo-Mechanical Description Of The Deformation Behavior, Scaling Laws, And Constitutive Modeling Of Nanoporous Gold, Mohammed Hassan Yousef Saffarini

LSU Doctoral Dissertations

Metallic foams, or nanoporous (NP) metals as it is widely referred to in literature, with ligament sizes up to a few tens of nm show exceptional mechanical properties such as high strength and stiffness per weight ratio under different loading scenarios due to their high surface area to solid volume ratio. Therefore, they can be utilized in a wide range of applications making them of great interest to researchers. While their elasticity and yield strength have been the subject of several studies, very limited attention was given to the effect of size, strain rate, and temperature on the material plastic …

Experimental Investigation Of The Performance Of A Hybrid Self-Healing System In Porous Asphalt Under Fatigue Loadings, Shi Xu, Liu Xueyan, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, which is designed to achieve autonomic damage repair in asphalt pavement, offers a great life-extension prospect and therefore not only reduces pavement maintenance costs but also saves energy and reduces CO2 emissions. The combined asphalt self-healing system, incorporating both encapsulated rejuvenator and induction heating, can heal cracks with melted binder and aged binder rejuvenation, and the synergistic effect of the two technologies shows significant advantages in healing efficiency over the single self-healing method. This study explores the fatigue life extension prospect of the combined healing system in porous asphalt. To this aim, porous asphalt (PA) test specimens with …

The Role Of Scenography In The Narration Of The Inner Space Of Contemporary Museums Through Employment The Space Staging, Shamael M. W. Al-Dabbagh, Dania Saleh Yaheia Al-Jaboury

Al-Esraa University College Journal for Engineering Sciences

In the recent period, several design mechanisms have emerged related to the design of internal spaces in architecture, specifically the museum spaces and associated with exhibitions, and the most important of these scenographic mechanisms are clearly and significantly adopted in the field of theater to design the stage and the scene that embodies the narrative vision and the idea of the theater director and scenographic designer to express what the text wants from Anecdotal expressing the objectives of the product of the text, therefore the research aimed to delve into the effect of the scenography mechanism on the contemporary architectural …

Evaluating The Performance Of The Jadriya Water Project For Water Treatment, Rana Mohammed Rasheed

Al-Esraa University College Journal for Engineering Sciences

For the purpose of evaluating the performance of the Al-Jadriya water project, water samples were taken before and after the sedimentation basins to find out the efficiency of the sedimentation ponds, as well as water samples were taken before and after the filtration basins, to know the efficiency of the filtration basins by conducting the following tests on them (Turbidity, TDS, TC, pH) to ensure that these ponds work properly. It was found that the efficiency rate of sedimentation ponds was 83%, which indicates the inefficiency of these ponds, as well as the inefficiency of the fast and slow mixing …

Possible Developments Of The Industrialization Of Appropriate Building Subsystem For Iraq, Wisam William Saleem Al-Ayoubi

Al-Esraa University College Journal for Engineering Sciences

Industrialization of building has developed very rapidly in industrialized countries as well as in many other parts of the world to fulfill the need for housing and public buildings after the Second World War. Prefabricated building is defined as a type of building that consists of several elements or modular units prepared in advance and assembled on-site. The term prefabricated indicates that these building elements are manufactured in the workshop or factory and then combined with other elements. Iraq has witnessed vital development in the construction industry sector. The study investigates the appropriate technology for Iraq, considering resources, economy, labor, …

Ion Exchange Method For Sulphate Removal From Treated Wastewater Of Al-Doura Refinery, Rana Mohammed Rasheed

Al-Esraa University College Journal for Engineering Sciences

The treated wastewater by the industrial Wastewater Treatment Plant (WWTP), commonly named (INGECO) in Al-Doura refinery, suffers from highly sulfate concentrations that exceed the EPA specified limits of 250 mg/L. Laboratory water quality historical data have been reviewed and analyzed to determine the annual rate, maximum, and peak sulfate concentrations, which were found to be 360 mg/L, 425 mg/L, and 550 mg/L, respectively. A field inspection was conducted to identify the reasons for the high sulfate concentrations in the wastewater of most refinery process units. It was found that the maximum required sulfate remaining concentration should not exceed 10 mg/L …

The Effect Of The Spirit Of The Place On The Formulation Of Emotion In Contemporary Arab-Islamic Architecture, Mahdi Saleh Al-Faraj, Dania Saleh Yaheia

Al-Esraa University College Journal for Engineering Sciences

Arab-Islamic architecture is characterized by both constants and variables, with spiritual aspects (content) representing the constants and physical aspects (form) representing the variables. It evolves based on changing times and needs, with compassion being a significant feature associated with its spiritual aspects. Compassion is essential for collective agreement and individual emotional connection in Arab-Islamic architecture. The present research aims to investigate the influence of the spirit of the place, as embraced by designers, on the emotional characteristics of contemporary Arab-Islamic architecture. The research problem identified is the lack of a theoretical concept regarding the impact of the spirit of the …

The Effect Of Bioenergy Systems On The Architectural Product The Effect Of Fung Shui And Biogetric To Achieve The Performance Of Architectural Space, Abdullah Saadon Al-Mamoory, Ann Samari Ibrahim

Al-Esraa University College Journal for Engineering Sciences

This research presents an analytical study exploring the vital systems of energy science and their influence on architecture by examining ancient environmental philosophies like Feng Shui in China and bio-geometry in Egypt. These philosophies serve as guiding principles for studying energy and its impact on human daily life, highlighting their effects on integrated ecosystems in the design of residential buildings at both external and internal levels. The study examines key aspects such as the influence of energy on furniture arrangement in living spaces. The primary objective is to establish a synergistic relationship between architectural design of residential spaces during occupancy …

Some Aspects Of The Suitability Of Three-Story Residential Buildings For Vertical Housing In Iraq, Wisam William Saleem Al-Ayoubi

Al-Esraa University College Journal for Engineering Sciences

This research initially aimed to examine the changes in housing since the 1930s, driven by rapid population growth and evolving lifestyles, juxtaposed with advancements in contemporary building materials that are environmentally compatible. After a comprehensive analysis of housing and living arrangements throughout history, including the evolution of open house units towards more interior-focused designs such as the Baghdadi house with its central courtyard, the study delved into the significant changes and the challenges posed by the rapid population growth. The focus of the study was on the viability of vertical housing in Iraq and the considerations related to low-rise residential …

Role Of Iconic Architecture In Sustainable Tourism Development, Basim H. H. Al-Majidi, Ann Samari Ibrahim

Al-Esraa University College Journal for Engineering Sciences

Architecture "is an expression of the way of life and the spirit of the ages and cultures in which I grew up" as the buildings speak for themselves. While tourism is a scenario "to define a city to an unfamiliar audience and acquire an identity for a citizen". Both architecture and tourism have been linked together since time immemorial. Architecture was the main aspect of attracting crowds, while tourism helped architecture survive the test of time as well as money. Both tourism and architecture operate in a symbiotic manner to break the lack of familiarity with any culture and to …

Assessment Of Carbon Dioxide Emission And Its Impact On High-Rise Mixed-Use Buildings In Egypt, Ahmed Salah Hamza

Theses and Dissertations

With Egypt's vision of 2030 focusing on sustainable development with a true emphasis on Carbon Dioxide (CO₂) emission reduction in the newly built cities and high-rise buildings, efforts are exerted on various levels towards accomplishing the vision’s goals. This is achieved through multiple tools and models associated with aiding the reduction of carbon emissions, yet not a clear one was introduced for the mixed-use buildings in Egypt.

Through this work, a significant gap was identified with respect to high-rise buildings carbon emission assessment in Egypt. This was a main driving force for this work in an attempt to …

Dental Cement Thickening Agents For Mudslide Prevention, Kristina Emiliya Babayev, Emily Elizabeth Johnson, Diana Evet Reihaneh

Materials Engineering

The purpose of this project is to develop a non-toxic mud thickening agent for the application of decreasing mudslide intensity where performance is measured by flow rate, viscosity, and toxicity tests. We hypothesized that dental cements could be a potential candidate due to their adhesive, hydrophilic, and biocompatible properties. Zinc phosphate, glass ionomer, and polycarboxylate cement were among the dental cements tested. These tests were performed at low and high concentrations of 25 grams and 125 grams, respectively, mixed into soil to produce 3500 gram samples. The dental cements produced noticeable thickening effects in the mud, as the average viscosity …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

Use Of Biomimicry Design Approach In Constructing Sustainable Resilient Structures (Case Study: Port Of Beirut), Farouk Bader, Marwan Halabi, Hiba Mohsen, Maged Youssef

BAU Journal - Creative Sustainable Development

Resiliency is not the same as sustainability, nor its substitute, but definitely the two concepts complement each other’s. Sustainability is the avoidance of depletion of natural resources to maintain ecological balance whereas resiliency is to recover, adapt and keep going in the face of setbacks. While designing with green approach is important but what will happen to leed points if the building becomes uninhabitable due to disasters, that’s where resiliency comes into play. The 2019 statistics showed that natural disasters accounted for 133 billion dollars losses and manmade ones accounted for other 7 billion in addition to 11,755 people worldwide …