Thermodynamics Commons^™

Neural Network Technologies In The Automatical Control Systems Of Absorption Process For Pureficating Natural Gas, Abdishukurov Maqsudovich Shavkat Mr, Xuecheng Li Li Xuecheng Mr

Technical science and innovation

Analysis of methods and algorithms for synthesizing adaptive control systems for technological processes based on the neural network approach is carried out in this search. The stages of mathematical modeling of complex technological processes using neural network technology were considered. Additionally, an algorithm for solving the interpolation and extrapolation problem that arises in the training process a neural network to control system was proposed. At the final stage of this article, algorithms based on neural network technology are synthesized for the control system for the parameters of the technological process of natural gas purification by absorption

Improving The Reliability And Performance Of A Supersonic Indraft Tube Wind Tunnel, Christian J. Kaml

Master's Theses

Access to supersonic testing is increasing in demand, and wind tunnels remain one of the safest and most cost-effective methods for gathering high-speed flow data. Despite being more economical than alternative options, supersonic wind tunnel facilities often require substantial investment to construct, operate, and maintain.

The novel indraft tube tunnel architecture was conceived as a high-speed flow testbed that incorporates features of both Ludwieg tubes and indraft wind tunnels to maintain costs low enough to be accessible even to small universities. This design was first developed and tested in 2018 at California Polytechnic State University, featuring a cost per test …

Design And Development Of A Resonance Ignition System Using Gaseous Propellants, Benjamin J. Hoefer

Master's Theses

This work presents the development and experimental evaluation of a resonance igniter (RI) operating with premixed gaseous propellants. Resonance ignition is a non-electrical ignition concept in which an underexpanded jet impinges on a closed-end Hartmann–Sprenger tube (HST), generating cyclic compression and expansion waves that rapidly heat gas near the tube endwall. A modular experimental system was designed and built to investigate resonance ignition using methane–air and methane–oxygen mixtures. The system includes a supplemental configuration that may probe for mixture conditions favorable to ignition, informing RI testing. Pressure and temperature measurements were used to characterize pressure control, mixture pressure ratio (MPR), …

Deep Learning Based Control System For Multi-Zone Hvac Residential Buildings, Mohammad H. Z. Alghalayeeni

Mechanical Engineering Theses

Heating, ventilation, and air conditioning (HVAC) systems are major contributors to residential energy consumption. However, most homes continue to rely on single zone thermostat control, which regulates temperature based on a single sensor and cannot account for thermal variations across multiple rooms. This often leads to uneven thermal conditions and inefficient energy use in multi-zone residential buildings. This thesis presents a deep reinforcement learning based approach for improving HVAC zoning control through dynamic airflow distribution. A physics based multi zone thermal model of a residential house was developed to simulate heat transfer processes including conduction, convection, solar and internal heat …

Computational Study Of Rotating Detonation Combustors, Aditya Balasubramaniam

Mechanical and Aerospace Engineering Theses

Rotating detonation combustors (RDCs) are pressure-gain combustion devices that sustain one or more continuously rotating detonation waves, offering potential thermodynamic and performance advantages over conventional deflagration-based systems. Their behavior depends strongly on combustor geometry and operating conditions. Understanding these effects is therefore essential for the design and optimization of practical RDCs. Accordingly, this thesis numerically investigates annular RDCs with two primary objectives: (1) to evaluate the effects of propellant mass flux and (2) to assess the influence of annular width on detonation-wave dynamics and combustor performance.

A finite-volume framework is used to solve the compressible reactive Euler equations with hydrogen–air …

Effect Of Inter Electrode Distance On Electrochemical Mineralization Of Calcium Carbonate In Mildly Acidic Environments, Irene Walker, Ivy Wu, Steven Decaluwe, Robert Bell, Kerry Rippy

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The effect of inter electrode distance (IED) on electrochemical mineralization in a parallel plate cell with a stainless-steel working electrode is presented. Three IEDs were tested, 6.5 mm, 15.5 mm, and 22.0 mm, for their water reduction effectiveness to create a region of local alkalinity that stimulates calcium carbonate precipitation in mildly acidic conditions. Chronoamperometry at -1.6 V for 30 minutes with ex-situ optical microscopy and scanning electron microscopy (SEM) were used. At the smallest IEDs, crystal clusters formed in growth-favored regimes as compared to the largest IED, where nucleation dominated, leading to encasement of the SS mesh. Rapid precipitation …

Advancing Sustainable Co2 Mitigation: Experimental And Computational Analysis Of Thermal Carbon Chitosan Sorbent For Automotive Exhaust Capture, Dalia A. Ali Dr., Amir Ahmed Elgamal Eng., Rania Rushdy Moussa Dr.

Chemical Engineering

This study investigated the efficiency of thermal carbon chitosan (TCCS) sorbent for CO2 capture from vehicle exhaust emissions within a designed adsorption system. TCCS was synthesized and meticulously characterized using a series of analytical techniques, including Brunauer-Emmett-Teller (BET) surface area analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), Ther- mogravimetric Analysis (TGA), Energy Dispersive X-ray Spectroscopy (EDX), and Differential Scanning Calo- rimetry (DSC). The TCCS adsorbent showed high thermal stability and a heating value (HHV) of 23.5 MJ/kg. Adsorption isotherm study demonstrated that the maximum capacity of CO2 adsorption is 0.084 kg.CO2/kg. TCCS, as well …

Comprehensive Review Of Sensible Thermal Storage Systems For Cooking Applications, Anna K. Shariishoy

Tanzania Journal of Engineering and Technology (TJET)

This paper reviewed the sensible thermal storage systems specifically designed for cooking applications. The review focuses on the characteristics of storage materials, their practical applications, and the overall performance of the systems. The review consolidated an array of experimental and numerical research published across various sources such as journals, conferences, books, online resources, and professional reports. A systematic review is used to reach the conclusion of this paper. Significant findings from this study include the wide range of storage capacities attained from small-scale systems that can store ~1–5 MJ of energy for a single meal to bigger systems that can …

Predicting The Influence Of Aggregate Size And Distribution On Cementitious Concrete Properties: A Review, Innocent J. Macha

Tanzania Journal of Engineering and Technology (TJET)

Cement concrete has been in use for centuries as one of the primary construction materials. Its demand in the construction industry is expected to continue for several centuries before the full development of alternative products. However, one of the main areas of research interest is understanding how its constituents can be tailored to make its properties predictable to reduce risks associated with structural failures, reconstruction and reduced durability. These hindrances associated with cementitious concrete result from several attributes, including constituent material characteristics, mixing ratios and workmanship. Understanding the predictability of cement concrete properties requires computer modelling tools to provide reliable …

Root Cause Analysis Of Performance Degradation For An Xyz Thermal Power Plant In Tanzania, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Thermal power plants in Tanzania have been experiencing performance degradation, typically arising from component and subsystem failures, which contribute to power system instability and unreliability. This paper presents a case study of the root causes of performance degradation of an XYZ thermal power plant. The study was conducted by reviewing plant documentations, including maintenance and operational data logbooks, and by standardising the approach through the adoption of ISO 14224:2016 for maintenance and reliability data exchange. Data evaluation was carried out using principal component analysis and scree plot analytical techniques to enhance the depth and accuracy of root cause identification. Additionally, …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Assessment Of Factors Contributing On Early Rotting Of Chromated Copper Arsenate Treated Utility Power Distribution Wood Poles In Tanzania, Innocent J. Macha

Tanzania Journal of Engineering and Technology (TJET)

The study aimed to assess the factors contributing to the premature decay of Chromated Copper Arsenate (CCA) treated utility power distribution wooden poles in Tanzania. Deteriorated poles samples from various regions in Tanzania were analyzed using handheld X-ray spectrometry to quantify the retention of CCA preservative chemicals. The ages of these poles were estimated based on annual growth rings. The findings indicated that premature failure of CCA treated wooden poles is attributed to an imbalance in the chemical composition of the preservative solution. The study found that CuO retention in most samples ranged between 10-18 kg/m3, significant lower that the …

Numerical Modelling And Co-Optimization Of Gasoline Fuels For Gasoline Compression Ignition Using Multi Component Approach, Ashwin Karthik Purushothaman

Dissertations, Master's Theses and Master's Reports

Future mobility is expected to rely on a broad spectrum of powertrain technologies, including battery electric vehicles (BEVs), hybrid electric vehicles (HEVs), fuel cell electric vehicles (FCEVs) and traditional internal combustion engine (ICE) vehicles. Despite the shift toward electrification, internal combustion engines are projected to remain a key component of future powertrains, either as the primary power source or as range extenders to generate electricity in hybrid systems. As such, significant research efforts continue to focus on enhancing the efficiency and reducing the emissions of ICEs to meet increasingly stringent regulatory and environmental targets. Gasoline compression ignition (GCI) has been …

Monitoring Of Laser Soldering Process In Hybrid Additive Manufacturing, Alexander P. Pustinger

Open Access Theses & Dissertations

Additive manufacturing (AM) has been a maturing technology that has expanded over the course of the last decade in major advancements especially in accessibility, process monitoring, modeling, and stock material design. As its industry use is growing, the demand for added improvements such as multi-functionality increases, such as with a hybrid system that allows for modification of printed parts with different electrical components like the Foundry Multi-3D system. The system's purpose is to create AM parts with multifunctional electrical components with the vision to expand to other areas of interest in manufacturing such as ISAM. This work explores the use …

Fabrication And Performance Of Scalable Bio-Engineered Porous Layers For Efficient Co2 Capture, Mary Sharon Rose Bondugula

Theses and Dissertations

This dissertation addresses the critical challenge of mitigating climate change by advancing CO2 capture technologies. As global CO2 emissions continue to rise, effective methods for capturing and separating CO2 from industrial processes are essential to combat climate change. Existing CO2 capture systems, such as Pressure Swing Adsorption (PSA) and Temperature Swing Adsorption (TSA), often rely on packed bed designs that face limitations, including poor heat and mass transfer, slow gas diffusion, and low thermal conductivity, reducing their efficiency. To overcome these challenges, this dissertation explores innovative solutions by developing advanced adsorbent coatings and scalable bed configurations.

This research begins by …

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

Synthesis Of Durable Zeolite 13x Insertion Coatings And Scaled-Up Experimental Demonstration For Co2 Capture, Daniel Jamil Hocheimy

Theses and Dissertations

Minimizing the energy requirement for capturing carbon dioxide (CO₂) from post-combustion sources is critical to efficient industrial decarbonization and subsequent mitigation of the effects of climate change. The current portfolio of CO₂ capture technologies includes absorption, membrane separation and packed bed adsorption, which suffer from high energy and temperature requirements, scalability, and location dependency issues. Adsorption-based systems could cater to these concerns; however, their current embodiments primarily use packed adsorbent bed design and electricity-driven vacuum pumps to regenerate them. While simple and easy to fabricate, these designs are not scalable and cannot use heat to regenerate them …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Carbon Dioxide Gasification Of Biochar: A Study On Utilizing Captured Co2 To Mitigate Greenhouse Gas Emission And Improving Carbon Conversion Efficiency, Nnamdi Ofuani

College of Graduate Studies: Theses & Dissertations

With rapidly growing global economies and world population, fossil fuel continues to play a major role in meeting current energy demands. Carbon capture and storage (CCS) technologies have, hence, been implemented to reduce CO₂ emissions in the atmosphere. With the implementation of CCS technologies comes the need to utilize the captured CO₂. This research, therefore, proposes CO₂ gasification of biochar as a viable carbon utilization pathway. With captured CO₂ coming at various concentrations, there is a need to understand how CO₂ concentration affects biochar conversion to useful products. This study, therefore, evaluates the effects …

Investigation Of Operational Parameter Differences Between The Standard Ron Test Method And Knock-Limited Modern Spark-Ignition Engine Operation, Alexander Hoth

Dissertations, Master's Theses and Master's Reports

Octane numbers (ONs) are used worldwide to rate the knock propensity of gasoline-like fuels for spark-ignition engines, making ONs the leading indicator of fuel quality for commercial distribution. The ONs were established 90 years ago and have only received minor changes compared to significant advancements in modern engine operation and fuel composition. This has resulted in discrepancies between knock-limited modern engine operation and standard ON ratings. This dissertation used a standard CFR octane rating engine at Argonne National Laboratory that was instrumented with modern combustion research tools to investigate key differences between the Research Octane Number (RON) rating conditions and …

Mathematical Modeling Of Coupled Heat And Mass Transfer In Metal-Hydride Hydrogen Storage Systems, Muhammad Hasnain

College of Graduate Studies: Theses & Dissertations

As a promising clean energy carrier hydrogen has recently gained significant interest, but its efficient and safe storage is a major challenge. Compared to the gaseous state and liquid state, metal hydrides (MH) offer a potentially more effective storage approach for hydrogen. However, the main challenge in this approach is the low thermal conductivity of the MH bed that leads to low heat transfer and ultimately to higher charging and discharging times. The purpose of this work is to develop an in-house comprehensive heat and mass transfer model for hydrogen sorption in MH reactors to simulate the dynamic behavior of …

Numerical Modeling Of Thermal Runaway In Lithium-Ion Batteries Using Decomposition Kinetics And Inter-Cell Contact Resistance, Shehzad Khan

College of Graduate Studies: Theses & Dissertations

Lithium-ion batteries (LIBs) are central in numerous high-demand applications due to their high energy density and prolonged cycle life. Despite these advantages, their susceptibility to thermal runaway (TR) poses a significant safety risk, with the potential for catastrophic failures. This study focuses on the thermal behavior of prismatic lithium-ion cells, using a finite volume-based partial differential equation (PDE) solver developed in MATLAB and JULIA to model TR behavior. This solver accurately simulates transient behaviors, convection, diffusion, and source terms across various coordinate systems. By engaging in a series of increasing complex case studies, this research aims to identify the critical …

Effects Of Electron Beam Irradiation On Crmnv And Crmntiv High Entropy Alloys: Nano-Mechanical, Structural, And Thermodynamic Perspectives, N. A. Sultana, Y. S. Mohammed, S. J. Pendleton, J. Vennekate, G. Ciovati, X. Li, H. Baumgart, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

Beam exit windows are crucial components of any particle accelerator as they provide an interface between the beamline vacuum and target material at atmospheric media. For high beam power machines, special materials and designs are required to withstand high radiation and mechanical loads, while minimizing energy loss during transition and maximizing window lifetime. This research investigates the impact of electron beam exposure to bulk CrMnV and CrMnTiV high entropy alloys (HEAs) with the primary goal of identifying suitable candidate materials for the design of robust and durable exit window settings. The selection criteria include intrinsic characteristics, power dissipation, and mechanical …

Data-Driven Modeling Of Oxygen Kinetics In La0.6sr0.4co0.2fe0.8o3−Δ (Lscf) For High-Temperature Reduction Of Co2 In An Electrolysis Cell, Ferron Campbell

Graduate Theses, Dissertations, and Problem Reports (ETD)

Electrolysis systems are critical to several societal applications, particularly energy storage and conversion. Developing these systems requires a detailed knowledge of the chemistry and thermodynamics of the materials used in the electrolysis cell. This work focuses on using embedded scientific machine learning as an efficient way to build an interpretable model for the reaction and transport kinetics in the LSCF electrode, whose performance directly influences the electrolysis system’s performance. The models developed in this study are trained using the publicly available machine learning package, FoKL-GP. This package incorporates a robust Gibbs sampler that employs a forward variable selection process to …

Numerical Investigations Of Sco2 Compressor Aerothermodynamics Using A Streamline Curvature Based Throughflow Method, Victor Quintanilla

UNLV Theses, Dissertations, Professional Papers, and Capstones

Supercritical carbon dioxide (sCO₂) has emerged as a promising working fluid for the Brayton power cycle, offering enhanced efficiency due to the high density and low viscosity of carbon dioxide (CO₂) near the critical point. A critical component of the sCO₂ Brayton cycle is the turbomachinery, namely the compressor, which significantly contributes to the efficiency enhancement in the sCO₂ Brayton cycle owing to reduced compression work requirements. Its primary function involves elevating the fluid's pressure, effectively priming it for the subsequent heat addition process from a thermal energy source. However, despite its advantages, challenges …

Employment Of Intelligent Predictive Maintenance On Thermal Power Plant Component Parts Taking Condenser Vacuum As A Case Study, Titus Ajewole

Tanzania Journal of Engineering and Technology (TJET)

This work proposes deployment of machine learning in the maintenance of individual constituent parts of steam power plant assemblages. With the condenser vacuum of a steam turbine (in a six-turbine plant assemblage) taken as a case study, information on the past operating parameters of the selected plant component was used to forecast its future working condition. Based on Exponential Gaussian Process of Regression, a model was developed, trained using the diachronic operational data, and employed in determining the future. A quantitative evaluation was employed to provide the distribution of the test values of the data about the lines of regression, …

Attrition Study Of Copper-Supplemented Iron-Based Oxygen Carrier For Chemical Looping Combustion, Neng Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Chemical looping combustion (CLC) is a promising technology that can mitigate the carbon emissions for power generation. The cost of oxygen carriers (OCs) impedes the scale up of CLC. Compared to synthetic iron-based OCs, red mud (RM), an abundant iron-based solid waste from industry, is a cost-effective choice due to its intrinsic inclusion of both inert and catalytic phases that are crucial for CLC. It was anticipated that the addition of copper oxide to RM using a mechanical mixing method that can be easily scaled up would enhance both reactivity and oxygen transport capacity (OTC), and the heat of reaction …