Polymer Science Commons^™

Electrochemical And Mechanical Evaluation Of Cellulose Acetate Electrolyte Films As A Function Of Polyetherimide And Polyethylene Glycol Additives For Supercapacitor Applications, Chase E. Golden

Chemical Engineering Undergraduate Honors Theses

Polymer electrolytes for supercapacitor applications require a balance between mechanical robustness and electrochemical performance. In this study, cellulose acetate (CA) films were modified with additives such as polyetherimide (PEI) and polyethylene glycol (PEG) to test how compositional changes influence mechanical performance, ionic conductivity, and electrochemical charge storage. Films were cast using phase inversion, soaked in a 1 M NaCl aqueous solution, and characterized using Fourier-transform infrared spectroscopy (FTIR), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and tensile testing. Films were also evaluated based on fluid uptake for insight into electrolyte retention.

Characterizations show that the addition of PEI increased ionic …

Purifying Circular Rna Therapeutics, Karen Guillen-Cuevas

All Dissertations

Circular RNA (circRNA) has emerged as a promising therapeutic modality due to its enhanced stability and resistance to exonuclease degradation compared with linear mRNA. However, its stability and functionality depend strongly on achieving high purity, and current methods such as size-exclusion chromatography suffer from peak overlap, low yields, and poor scalability. This dissertation addresses these limitations by developing ultrafiltration-based strategies to purify circRNA directly from in vitro transcription (IVT) and self-splicing (circularization) reactions. First, the feasibility of ultrafiltration was demonstrated using polyethersulfone membranes, where sieving coefficients and critical flux values of circRNA, precursor RNA, and nicked RNA were measured to …

Theoretical And Experimental Investigation Of Liquid-Liquid Phase Separation: Characterizing Elastin-Like-Polypeptides, Adam D. Quintana

Chemical and Biological Engineering ETDs

This dissertation develops and validates a semi-empirical Flory–Huggins-based interaction model, combined with Cahn–Hilliard simulations, for predicting multi-component liquid–liquid phase separation (LLPS) in elastin-like polypeptide (ELP) systems. Equilibrium droplet compositions, measured using a PDMS-based microfluidic device, enabled direct parameterization of interaction coefficients. The model was applied to generate phase diagrams and assess composition dependence in ternary mixtures. Cahn–Hilliard simulations were conducted to explore potential phase morphologies under different interfacial conditions. Multi-component Lattice Boltzmann simulations were implemented to model droplet morphology evolution under varying interfacial and diffusive parameters, reproducing experimentally relevant morphologies. A three-phase wetting study revealed conditions for selective wetting and …

Design And Characterization Of Lignin-Based, Thermoresponsive Soft Composites With Improved Mechanical And Transport Properties, Missoury D. Wolff

All Dissertations

In an attempt to reduce reliance on petroleum-based polymers, lignin – an abundant biopolymer – has gained popularity as a sustainable alternative. However, research on lignin-containing soft composites – i.e., hydrogel (bio)composites – has largely been heuristic, providing limited insight into the fundamental structure-processing-property relationships that govern performance improvements in this emerging class of ‘green’ soft composites. As such, this dissertation presents a systematic investigation of how lignin molecular weight (MW), composite composition, and the concentrations of crosslinker and accelerator impact the mechanical and transport characteristics of soft composites composed of lignin, poly(N-isopropylacrylamide) (PNIPAm), and poly(vinyl alcohol) (PVA).

In the …

Voltammetric Determination Of Hydrogen Peroxide At Decorated Palladium Nanoparticles/Poly 1,5- Diaminonaphthalene Modified Carbon-Paste Electrode, Ziad Khalifa, Mohamed Fathi Abo Oura, Magdi Abdelazzem, Ablah Hathoot

Chemical Engineering

In this work, palladium nanoparticles (PdNPs)/p1,5-DAN/ carbon paste electrode (CPE) and p1,5-DAN/CPE sensors have been developed for determination of hydrogen peroxide. Both sensors showed a highly sensitive and selective electrochemical behaviour, which were derived from a large specific area of poly 1,5 DAN and super excellent electroconductibility of PdNPs. PdNPs/p1,5-DAN/CPE exhibited excellent performance over p1,5-DAN/CPE. Thus, it was used for detecting hydrogen peroxide (H2O2) with linear ranges of 0.1 to 250 μM and 0.2 to 300 μM as well as detection limits (S/N= 3) of 1.0 and 5.0 nM for square wave voltammetry (SWV) and cyclic voltammetry (C.V) techniques, respectively. …

Sulfonated Ionomer Composite Membranes For Use In Vanadium Redox Flow Batteries, Xueting Wang

All Dissertations

While vanadium redox flow batteries (VRFBs) have garnered significant attention as a promising scalable energy storage technology, the current membrane material used in this technology, Nafion™, suffers from high cross mixing of vanadium ions in the liquid electrolytes, directly impacting battery performance properties such as the voltage and coulombic efficiencies, as well as resulting in a reduction in the overall battery lifetime. The use of ionomer nancomposites has proven to be one promising route of directly addressing the issue of high ion crossover, though the mechanism by which the nanoparticles act to reduce crossover remains in open question. Herein, the …

Experimental Evaluation Of Mesh Size In Physically Crosslinked Polymer Gels Using Dynamic Light Scattering, Duncan M. Hill

Honors Theses

Block copolymer gels are under consideration as drug delivery patches. Controlling and modeling the transport inside the gel is an important contribution to the successful delivery of pharmaceuticals. The diffusive transport of a solute – such as a therapeutic compound – within the gel can be described by the mesh size of the gel, which is defined as the distance between polymer chains. Existing experimental evaluations of mesh size do not work for block copolymer gels due to differences in the fundamental gel structure. As such, an experimental method of measuring mesh size of block copolymer gels using dynamic light …

Sustained Release Systems For Endometrial Cancer, Claire E. Rowlands

Theses and Dissertations--Chemical and Materials Engineering

Endometrial cancer (EC) is the sixth most common cancer in women worldwide and is the most common cancer of female reproductive organs. From 2007-2016 there has been a global rise in incidence of EC of 1.3 %. Typically, EC is treated with surgery, but at later stages surgery is less effective requiring chemotherapy and/or radiation therapy. These treatment options are less effective than surgery and there are very few FDA approved chemotherapies for EC. The minuscule number of effective treatment options as well as an increase in incidence shows the need for creating improved treatments for EC. There has been …

Novel Membrane Materials For Nutrient Recovery From Nutrient-Rich Resources, Km Prottoy Shariar Piash

Graduate Theses, Dissertations, and Problem Reports (ETD)

Global demand for fertilizer production is expanding substantially to meet the food demand of an increasing world population. Anaerobic digestate (AD) of various centralized wastewater facilities contains substantial amounts of ammonium (NH₄⁺) (300-800 mg/L), potassium (K⁺) (13-120 mg/L), and phosphorus (P) (30-100 mg/L)- based nutrients. In addition to reducing energy costs and CO₂ emissions compared to conventional fertilizing raw material manufacturing, recovering nutrients from these waste streams could help mitigate problems such as eutrophication, which otherwise incurs billions of dollars losses to US economy annually. Apart from nutrients, wastewater streams also contain organic pollutants …

Polylactic Acid (Pla) Containing Talc Microparticles And Amorphous Polyhydroxyalkanoates (Aphas) For Improved Barrier And Mechanical Properties In Food Packaging, Mohammed Alfaifi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Polylactic acid (PLA) is a biobased and compostable polymer that is increasingly being used as an alternative to petroleum-based, non-biodegradable polymers for single-use food packaging due to its environmental benefits. It is also commercially available in large quantities, and it can be processed like polyethylene. However, it has a higher water-vapor permeability (WVP) as compared to polyolefins and polyethylene terephthalate that are the incumbent materials. This results in a competitive disadvantage in employing PLA for packaging baked goods since the shelf life of the food is likely to be reduced. In the past, barrier properties of PLA were improved by …

Amine-Functionalized Lignin-Based Ionomer Nanocomposites For Redox Flow Batteries, Joshua Wilder

All Theses

As the development of energy storage technologies for renewable energy sources continues to garner attention, vanadium redox flow batteries (VRFBs) have emerged as promising source for grid-scale energy storage. A major component of the VRFB is the ion exchange membrane (IEM), as it serves to physically separate the two liquid electrolytes and also directly impacts the battery’s capacity, efficiency, and cost. The current industry standard IEM, Nafion™, not only accounts for a large portion of the cost of the VRFB but also suffers from poor proton selectivity. Herein, we have synthesized sulfonated poly(ether ether ketone) (SPEEK) composite membranes containing amine …

Elucidating The Mechanical And Transport Properties Of Lignin-Based Hydrogel Composites, Nicholas Gregorich

All Dissertations

The use of lignin in the fabrication of soft composites has become an emerging area of research in polymer science and polymer chemistry. These lignin-based materials present numerous benefits, notably, a reduction in the use of petroleum-based precursor, improved structural benefits to otherwise soft host polymers, as well as the inherent antimicrobial and antioxidant properties of lignin, making it suitable for biomaterials. Herein, we present two chemical reaction pathways of incorporating lignin that was fractionated and cleaned using the Aqueous Lignin Purification with Hot Agents (ALPHA) process into poly(vinyl alcohol) (PVA) hydrogel composites for aqueous-based separations. By leveraging the ALPHA …

Removal Of Hexavalent Chromium From Water By Chitosan-Enhanced Ultrafiltration, Putu A. Y. Indiasih, Anindita D. Syaifudin, Nurul Faiqotul Himma, Bambang Ismuyanto

Makara Journal of Technology

Polymer-enhanced ultrafiltration has gained increasing attention as a selective separation process to remove small solutes, such as metal ions, from water or wastewater. Hexavalent chromium Cr(VI) is one of the metal ions in wastewater that has received considerable attention because of its toxicity. Chitosan was used in this study as the polymer to bind Cr(VI) to enhance its removal by ultrafiltration. The effects of chitosan-to-Cr(VI) ratio on Cr(VI) rejection and permeate flux were investigated. In addition, the fouling tendency was evaluated. Results showed that the addition of chitosan with a mass ratio of 12.5 increased the Cr (VI) rejection from …

The Effect Of Different Fracturing Fluids On The Productivity Of Multi-Staged Fractured Marcellus Shale Horizontal Wells, Vida Gyaubea Matey-Korley

Graduate Theses, Dissertations, and Problem Reports (ETD)

While hydraulic fracturing has undeniably improved the production from oil and gas reservoirs, this technology is not without limitations. The primary hurdles lie in the areas of proppant transport, fluid rheology, and stress management. Despite the extensive research conducted in this domain, there remains a considerable amount of work to be done for comprehensive solutions that account for the complex interactions among fracturing fluid, proppant distribution, and geomechanical conditions. Achieving this will then make room for a holistic and efficient hydraulic fracturing strategy.

This study addresses the above-mentioned problem by examining the impact of fluid type on proppant transport and …

Mechanisms Of Emulsion Destabilization: An Investigation Of Surfactant, Stabilizer, And Detergent Based Formulations Using Diffusing Wave Spectroscopy, Jordan N. Nowaczyk

Theses and Dissertations

Conventional approaches for studying emulsions, such as microscopy and macroscopic phase tracking, present challenges when it comes to establishing detailed mechanistic descriptions of the impact of emulsifier and stabilizer additives. Additionally, while a combination of sizing methods and macroscopic phase tracking can provide insights into droplet size changes and concentration, the use of multiple measurements can be cumbersome and error-prone. It is the focus of this work, to present a new method for studying water in oil (W/O) emulsions that involves using diffusing wave spectroscopy (DWS) to examine the impact of three different surface stabilizing additives at varying concentrations. By …

Tuning Electrochemical Interactions And Polymer Electrolyte Interfaces For Enhanced Organic Acid Separations Using Electrodeionization, Matthew Leo Jordan

LSU Doctoral Dissertations

Chemical separations are critical processes for chemical and industrial plants to purify and isolate products however current separation technologies, such as distillation, rely on energy intensive processes. Electrochemical separation processes, such as electrodialysis and electrodeionization, are an energy efficient alternative that are emerging as an alternative for thermal-based separations. Organic acids are weakly ionizable species and susceptible for purification from process streams using electrochemical processes. Recently the fermentation route has garnered greater attention as a means for producing value-added chemicals, such as organic acids, from a renewable feedstock and aiding the circular economy. Some of the challenges electrodialysis faces for …

Water Recovery From Bioreactor Mixed Liquors Using Forward Osmosis With Polyelectrolyte Draw Solutions, Calen Raulerson

All Theses

The objective of this research was to test the feasibility of using forward osmosis (FO) with polyelectrolyte draw solutions to recover water from bioreactor mixed liquors. When combined with an Anaerobic Osmotic Membrane Bioreactor (AnOMBR), such a system could process fecal and food waste from astronauts aboard the International Space Station (ISS) and reclaim important nutrients and water. This project focused on measuring the obtainable water recovery rates from bioreactor effluent, and the identifying challenges associated with the operation.

AnOMBRs feature several advantages over aerobic bioreactors, and non-osmotic anaerobic membrane bioreactors (AnMBR). Anaerobic bioreactors avoid the significant energy costs of …

Gum Arabic-Capped Silver Nanoparticles For Electrochemical Amplification Sensing Of Methylene Blue In River Water, Ziad Khalifa, Moustafa Zahran, Magdy Zahran, Magdi Abdelazzem

Chemical Engineering

Herein, a novel electrochemical amplification sensor is developed for detecting methylene blue (MB) us- ing gum Arabic-capped silver nanoparticles (AgNPs) for the first time. Gum Arabic-AgNPs were fabricated via a direct chemical reduction technique using silver nitrate as an AgNPs precursor and gum Arabic as a reducing and capping agent. They were characterized using ultraviolet-visible (UV–Vis) spectrophotom- etry, square wave voltammetry (SWV), and transmission electron microscopy (TEM). UV–Vis and SWV results show the characteristic absorption and electrochemical oxidation peaks of the AgNPs at 431 nm and 0.18 V, respectively. Additionally, TEM images of the AgNPs show that they are spherical …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Extraction Of Micro- And Nano-Plastic Particles From Water Using Hydrophobic Natural Deep Eutectic Solvents, Jameson R. Hunter

Theses and Dissertations--Biosystems and Agricultural Engineering

The production of plastic and the amount of waste plastic that enters the environment increases every year. Synthetic polymers will gradually break down into particles on the micro- and nano-scale. The micro- and nano-plastics pose a significant ecological harm by transporting toxic chemicals and causing inflammation and cellular damage when ingested. Two common plastics are polyethylene terephthalate (PET) and Polystyrene (PS), and a newer bioplastic polylactic acid (PLA) that has become a popular alternative. Deep eutectic solvents are a recently discovered solvent composed of a hydrogen bond donor and hydrogen bond acceptor and have been proposed as a cheaper alternative …

Assessing Solvent Viscosity Impact On The Physical Characteristics Of Polymeric Organogels, Cameron Hong

Honors Theses

Traditionally, studies of polymeric organogels focus on the impact of polymer factors (e.g., molecular weight and polymer concentration) on the gels’ mechanical and transport properties. Alternatively, this study seeks to assess the impact of altering solvent viscosity, while holding polymer factors constant. The gels in this study were composed of different viscosity mineral oils, styrene-ethylene-butylene-styrene (SEBS) triblock copolymer as a gelator, and oleic acid (OA) as a model drug. Samples were formulated to have 6.5, 11.2, and 15.7 wt% SEBS copolymer for each mineral oil, varying in viscosity from ≈30 mPa*s to ≈500 mPa*s. Uniaxial mechanical testing was performed to …

Assessing The Impact Of Block-Selective Homopolymers On The Diffusion Of Payload Through Polymeric Organogels, Ian Coates

Honors Theses

Styrenic polymer gels have received recent attention for their application in transdermal patches due to their unique properties. Previous research in the pharmaceutical industry has identified that polymeric gels, specifically styrenic gels, have the potential to encompass multiple functions of the transdermal delivery patch including controlling mechanical and delivery properties. To tailor styrenic gels either the gel nanostructure or the drug complex can be controlled. Specifically, this thesis investigated the effect of gel nanostructure in an attempt to control the gel diffusivity and mechanical properties. To control gel nanostructure a phase selective styrene homopolymer was used at varying concentrations. It …

Establishing Independent Tunability Of The Mechanical And Transport Properties Of Polymer Gels, Lucas Rankin

Master’s Theses

Polymer gels can be used in the fabrication of materials for filtering liquid and gaseous media, solid-state electrolytes, and transdermal medical patches. This diverse range of applications primarily relies on the transport and mechanical properties of polymer gels. Both sets of properties have shown excellent tunability, but typically in a coupled fashion. Establishing the independent tunability of the transport and mechanical properties of polymer gels (using simple, cost-effective methods) is paramount if polymer gels are to be used to their full potential. Specifically, block copolymer gels self-assemble into organized nanoscale networks within the gel solvent, which allows for facile control …

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …

A Foundational Approach To Extrusion And Compounding, David Frankart

Williams Honors College, Honors Research Projects

With a history of nearly 200 years, polymer processing and compounding is constantly changing to fit the material science needs of the era. Exposure of undergraduate students to the technology and practices used in industry today in a lab setting would create new opportunities for experiential learning and growth. The objective was to set up a 0.75”, 25 L/D Thermo Haake single screw extruder for lab use and run trials of material in a single screw extruder to set up a basis for experiments. Trials were run of co-polyester resin through a single screw extruder with carbon fiber additives varying …

Elucidating The Properties And Mechanism For Cellulose Dissolution In Tetrabutylphosphonium-Based Ionic Liquids Using High Concentrations Of Water, Brad Crawford

Graduate Theses, Dissertations, and Problem Reports (ETD)

The structural, transport, and thermodynamic properties related to cellulose dissolution by tetrabutylphosphonium chloride (TBPCl) and tetrabutylphosphonium hydroxide (TBPH)-water mixtures have been calculated via molecular dynamics simulations. For both ionic liquid (IL)-water solutions, water veins begin to form between the TBPs interlocking arms at 80 mol % water, opening a pathway for the diffusion of the anions, cations, and water. The water veins allow for a diffusion regime shift in the concentration region from 80 to 92.5 mol % water, providing a higher probability of solvent interaction with the dissolving cellulose strand. The hydrogen bonding was compared between small and large …

Formulation And Validation Of Nanoparticle Controlled Delivery For Chemotherapeutic Drug Products, Shani L. Levit

Theses and Dissertations

Taxol, a formulation of paclitaxel (PTX), is one of the most widely used anticancer drugs, particularly for treating recurring ovarian carcinomas following surgery. Clinically, PTX is used in combination with other drugs such as lapatinib (LAP) to increase treatment efficacy. Delivering drug combinations with nanoparticles has the potential to improve chemotherapy outcomes. In this study, we use Flash NanoPrecipitation, a rapid, scalable process to encapsulate weakly hydrophobic drugs (logP in vitro. Encapsulating either PTX or LAP into nanoparticles increases drug potency. When PTX and LAP are co-loaded in the same nanoparticle, they have a synergistic effect that is greater than …

Chemical And Physical Modification Of Thiol-Ene And Epoxy-Amine Networks For Advanced Control Of Gas Transport And Flame Retardant Behavior, Vivek Vasagar

Dissertations

Crosslinked polymers are widely used due to its several advantages not limited to high mechanical strength combined with the easy processability. Despite of its popular usage, the fundamental understanding of polymer structure affecting the desired properties is still lacking. This PhD thesis is in two parts, the first part is devoted to the design and developing a basic understanding of structure and chemical composition dependencies of gas transport, whereas in the second part a fundamental relationship between structure to the fire-retardant properties is established.

Membrane based gas separation technique has attracted interest of selective removal of carbon dioxide gas from …

Synthesis, Functionalization, And Application Of Nanofiltration And Composite Membranes For Selective Separations, Andrew Steven Colburn

Theses and Dissertations--Chemical and Materials Engineering

Future nanofiltration (NF) membranes used for selective separations of ions and small organic molecules must maintain performance in environments where high concentrations of total dissolved solvents or foulants are present. These challenges can be addressed through the development of composite membranes, as well as the engineering of enhanced surface properties and operating conditions for existing commercial membranes.

In this work, ion transport through commercial thin film composite (TFC) polyamide NF membranes were studied in both lab-prepared salt solutions and industrial wastewater. The dependence of several variables on ion rejection was investigated, including ion radius, ion charge, ionic strength, and temperature. …

Synthesis, Characterization And Applications Of Reduced Graphene Oxide And Composite Membranes For Selective Separations And Removal Of Organic Contaminants, Ashish Aher

Theses and Dissertations--Chemical and Materials Engineering

Among the next generation materials being investigated for membrane development, partially reduced Graphene Oxide (rGO) has received increasing attention from the membrane community. rGO-based nanofiltration membranes have shown promising results in applications such as partial desalination, organic contaminant removal, gas-phase separations, and separations from solvent media. rGO offers a unique platform compared to common polymeric membranes since it can be used for separation applications in both aqueous and organic solvent media. An rGO-based platform could also be utilized to synthesize reactive membranes, giving rGO membranes the additional capability of reactively removing organic contaminants. This research focuses on the synthesis of …