Other Chemical Engineering Commons^™

Infrared Optical Properties Of Amorphous And Nanocrystalline Ta2o5 Thin Films, Trevor J. Bright, J. I. Watjen, Zhuomin Zhang, Christopher Muratore, Andrey A. Voevodin, D. I. Koukis, David B. Tanner, Daniel J. Arenas

Chemical and Materials Engineering Faculty Publications

The optical constants of tantalum pentoxide (Ta 2O5) are determined in a broad spectral region from the visible to the far infrared. Ta 2O5 films of various thicknesses from approximately 170 to 1600 nm aredeposited using reactive magnetron sputtering on Si substrates. X-ray diffraction shows that the as-deposited films are amorphous, and annealing in air at 800 °C results in the formation of nanocrystallineTa 2O5. Ellipsometry is used to obtain the dispersion in the visible and near-infrared. Two Fourier-transform infrared spectrometers are used to measure the transmittance and reflectance at wavelengths from 1 to 1000 μm. The surface topography and …

Cross-Plane Thermal Properties Of Transition Metal Dichalcogenides, Christopher Muratore, Vikas Varshney, Jaime J. Gengler, Jianjun Hu, John E. Bultman, Timothy M. Smith, Patrick J. Shamberger, Bo Qiu, Xiulin Ruan, Ajit K. Roy, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

In this work, we explore the thermal properties of hexagonal transition metal dichalcogenide compounds with different average atomic masses but equivalent microstructures. Thermal conductivity values of sputtered thin films were compared to bulk crystals. The comparison revealed a >10 fold reduction in thin film thermal conductivity. Structural analysis of the films revealed a turbostratic structure with domain sizes on the order of 5–10 nm. Estimates of phonon scattering lengths at domain boundaries based on computationally derived group velocities were consistent with the observed film microstructure, and accounted for the reduction in thermal conductivity compared to values for bulk crystals.

Tannic Acid Coated Gold Nanorods Demonstrate A Distinctive Form Of Endosomal Uptake And Unique Distribution Within Cells, Emily A. Untener, Kristen K. Comfort, Elizabeth I. Maurer, Christin M. Grabinski, Donald A. Comfort, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

One of the primary challenges associated with nanoparticle-dependent biological applications is that endosomal entrapment in a physiological environment severely limits the desired targeting and functionality of the nanoconstructs. This study sought to overcome that challenge through a systematic approach of gold nanorod (GNR) functionalization: evaluating the influence of both aspect ratio and surface chemistry on targeted cellular internalization rates and preservation of particle integrity. Owing to their unique spectral properties and enhanced surface area, GNRs possess great potential for the advancement of nanobased delivery and imaging applications. However, their ability for efficient intracellular delivery while maintaining their specific physiochemical parameters …

Applications Of High Throughput (Combinatorial) Methodologies To Electronic, Magnetic, Optical, And Energy-Related Materials, Martin L. Green, Ichiro Takeuchi, Jason R. Hattrick-Simpers

Faculty Publications

High throughput (combinatorial) materials science methodology is a relatively new research paradigm that offers the promise of rapid and efficient materials screening, optimization, and discovery. The paradigm started in the pharmaceutical industry but was rapidly adopted to accelerate materials research in a wide variety of areas. High throughput experiments are characterized by synthesis of a “library” sample that contains the materials variation of interest (typically composition), and rapid and localized measurement schemes that result in massive data sets. Because the data are collected at the same time on the same “library” sample, they can be highly uniform with respect to …

Characterization Of And Controlling Morphology Of Ultra-Thin Nanocomposites, Guy C. Laine

Theses and Dissertations--Chemical and Materials Engineering

Ultrathin film nanocomposites are becoming increasingly important for specialized performance of commercial coatings. Critical challenges for ultrathin film nanocomposites include their synthesis and characterization as well as their performance properties, including surface roughness, optical properties (haze, refractive index as examples), and mechanical properties. The objective of this work is to control the surface roughness of ultrathin film nanocomposites by changing the average particle size and the particle volume fraction (loading) of monomodal particle size distributions. This work evaluated one-layer and two-layer films for their surface properties. Monodispersed colloidal silica nanoparticles were incorporated into an acrylate-based monomer system as the model …

Fabrication And Characterization Of Thermomechanically Processed Sulfur And Boron Doped Amorphous Carbon Films, Lonnie Carlson

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

Small scale, high power density, reliable, and long-life power supplies would be useful or even critical for space missions or the growing number of microdetectors, microsensors, and miniature vehicles. Alpha or beta particle voltaic devices could satisfy these requirements but have been shown to degrade quickly due to radiation damage. Amorphous carbon (a-C) PN junctions or PIN devices could provide radiation hardness and sufficiently high efficiency. As the range of alpha and beta particles in a-C is ~20-120μm, much thicker films than are typical are needed to maximize collection of the particle energy.

In this work, the fabrication of thermomechanically …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

Limited Thermal Conductance Of Metal-Carbon Interfaces, Jaime J. Gengler, Sergei V. Shenogin, John E. Bultman, Ajit K. Roy, Andrey A. Voevodin, Christopher Muratore

Chemical and Materials Engineering Faculty Publications

The thermal conductance for a series of metal-graphite interfaces has been experimentally measured with time-domain thermoreflectance (TDTR). For metals with Debye temperatures up to ∼400 K, a linear relationship exists with the thermal conductance values. For metals with Debye temperatures in excess of ∼400 K, the measured metal-graphite thermal conductance values remain constant near 60 MW m−2 K−1. Titanium showed slightly higher conductance than aluminum, despite the closeness of atomic mass and Debye temperature for the two metals. Surface analysis was used to identify the presence of titaniumcarbide at the interface in contrast to the aluminum and gold-carbon interfaces (with …

Design Mixers To Minimize Effects Of Erosion And Corrosion Erosion, Julian B. Fasano, Eric E. Janz, Kevin J. Myers

Chemical and Materials Engineering Faculty Publications

A thorough review of the major parameters that affect solid-liquid slurry wear on impellers and techniques for minimizing wear is presented. These major parameters include (i) chemical environment, (ii) hardness of solids, (iii) density of solids, (iv) percent solids, (v) shape of solids, (vi) fluid regime (turbulent, transitional, or laminar), (vii) hardness of the mixer's wetted parts, (viii) hydraulic efficiency of the impeller (kinetic energy dissipation rates near the impeller blades), (ix) impact velocity, and (x) impact frequency. Techniques for minimizing the wear on impellers cover the choice of impeller, size and speed of the impeller, alloy selection, and surface …

Giant Magnetostriction In Annealed Co1-XFeX Thin-Films, Dwight Hunter, Will Osborn, Ke Wang, Nataliya Kazantseva, Jason R. Hattrick-Simpers, Richard Suchoski, Ryota Takahashi, Marcus L. Young, Apurva Mehta, Leonid A. Bendersky, Same E. Lofland, Manfred Wuttig, Ichiro Takeuchi

Faculty Publications

Chemical and structural heterogeneity and the resulting interaction of coexisting phases can lead to extraordinary behaviours in oxides, as observed in piezoelectric materials at morphotropic phase boundaries and relaxor ferroelectrics. However, such phenomena are rare in metallic alloys. Here we show that, by tuning the presence of structural heterogeneity in textured Co_1−xFe_x thin films, effective magnetostriction λeff as large as 260 p.p.m. can be achieved at low-saturation field of ~10 mT. Assuming λ100 is the dominant component, this number translates to an upper limit of magnetostriction ofλ100≈5λeff >1,000 p.p.m. Microstructural analyses …

Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

A hybrid plasma deposition process, combining matrix assisted pulsed laser evaporation (MAPLE) of carbon nanopearls (CNPs) with magnetron sputtering of gold was investigated for growth of composite films, where 100 nm sized CNPs were encapsulated into a gold matrix. Composition and morphology of such composite films was characterized with x-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM) analysis. Carbondeposits on a gold magnetron sputter target and carbon impurities in the gold matrices of depositedfilms were observed while codepositing from gold and frozen toluene-CNP MAPLE targets in pure argon. Electrostatic quadrupole plasma analysis was used to determine that …

Chameleon Coatings: Adaptive Surfaces To Reduce Friction And Wear In Extreme Environments, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Adaptive nanocomposite coating materials that automatically and reversibly adjust their surface composition and morphology via multiple mechanisms are a promising development for the reduction of friction and wear over broad ranges of ambient conditions encountered in aerospace applications, such as cycling of temperature and atmospheric composition. Materials selection for these composites is based on extensive study of interactions occurring between solid lubricants and their surroundings, especially with novel in situ surface characterization techniques used to identify adaptive behavior on size scales ranging from 10−10 to 10−4 m. Recent insights on operative solid-lubricant mechanisms and their dependency upon the ambient environment …

Thermal Damage Approach Of Concrete: Application To Specimens Subjected To Combined Compressive And High Temperature Loads, Abdellah Menou, Ghassan Mounajed, Hocine Boussa, Christian La Borderie, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Within the framework of study of concrete structures subjected to fire, .a theoretical and experimental work was conducted. The aim of this study was to investigate and to model the damage mechanisms of concrete after their exposure to high temperatures. The multiphase Digital Concrete Model as well as the damage model, MOD EV, which were both implemented on the finiteelem~ rit software package, SYMPHONIE, were used simμltaneously to assess the thermal damage of the concrete. In order to validate the thermal damage model, an experimental investigation was performed. The mechanical characteristics of 5 cementitious materials, which included cement paste, mortar, …

Effect Of Carbon Nanofiber-Matrix Adhesion On Polymeric Nanocomposite Properties—Part Ii, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

A successful integration of two independent phases with good adhesion is imperative for effective translation of superior carbon nanofiber filler properties into a physically superior carbon nanocomposite. Carbon nanofibers were subjected to electrochemical oxidation in 0.1 M nitric acid for varying times.

The strength of adhesion between the nanofiber and an epoxy matrix was characterized by flexural strength and modulus. The surface functional groups formed and their concentration of nanofibers showed a dependence on the degree of oxidation. The addition of chemical functional groups on the nanofiber surface allows them to physically and chemically adhere to the continuous resin matrix. …

Carbon Nanoadditives To Enhance Latent Energy Storage Of Phase Change Materials, Shadab Shaikh, Khalid Lafdi, Kevin P. Hallinan

Chemical and Materials Engineering Faculty Publications

Latent energy storage capacity was analyzed for a system consisting of carbon nanoparticlesdopedphase changematerials (PCMs). Three types of samples were prepared by doping shell wax with single wall carbon nanotubes(SWCNTs), multiwall CNTs, and carbon nanofibers. Differential scanning calorimetry was used to measure the latent heat of fusion. The measured values of latent heat for all the samples showed a good enhancement over the latent heat of pure wax. A maximum enhancement of approximately 13% was observed for the wax/SWCNT composite corresponding to 1% loading of SWCNT. The change in latent heat was modeled by using an approximation for the intermolecular …

Nitrogen And Hydrogen Plasma Treatments Of Multiwalled Carbon Nanotubes, John G. Jones, A. R. Waite, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

This article investigates plasma treatment of vertically aligned multiwall carbon nanotube (CNT) films in different plasma environments for modification of surface chemistry and morphology. The surfaces of the CNTs were functionalized with a pulsed dc plasma treatment, where the power was directly applied to the nanotube film in low pressure argon/nitrogen and argon/hydrogen backgrounds. Optical emission spectroscopy was used to detect atomic and molecular excitations in the gas mixtures as well as in pure gases in the vicinity of the CNT films. In situx-ray photoelectron spectroscopy was performed on the treated samples to examine CNT surface chemistry after treatment. …

Enhanced Dielectric Properties In Single Crystal-Like Bifeo3 Thin Films Grown By Flux-Mediated Epitaxy, S.-H. Lim, M. Murakami, J. H. Yang, S.-Y. Young, Jason R. Hattrick-Simpers, M. Wuttig, L. G. Salamanca-Riba, I. Takeuchi

Faculty Publications

We have fabricated single crystal-like BiFeO₃ (BFO) thin films by flux-mediated epitaxy using pulsed laser deposition(PLD). The Bi–Cu–O flux composition and its thickness were optimized using composition spread, thickness gradient, and temperature gradient libraries. The optimized BFO thin films grown with this technique showed larger grain size of ∼2μm and higher dielectric constant in the range of 260–340 than those for standard PLD grown films. In addition, the leakage current density of the films was reduced by two orders of magnitude compared to that of standard PLD grown films.

Signaling Pathways Activated By Interleukin-2 And Interluekin-4 Receptors Mediate T Lymphocyte Clonal Expansion, Kristen K. Comfort

Chemical and Materials Engineering Faculty Publications

Cells sense and respond to chemical and physical stimuli through signal transduction pathways, which mediate cell proliferation, differentiation, migration, and survival. The cytokines interleukin-2 (IL-2) and interleukin-4 (IL-4) are key regulators of the adaptive immune system, particularly influencing the clonal expansion and differentiation of T cells. At least in culture, both synergistic and antagonistic effects of IL-2 and IL-4 co-stimulation have been reported; the antagonism, when observed, is thought to arise from the utilization of a common subunit shared by IL-2 and IL-4 receptors. We have sought to characterize IL-2 and IL-4 signaling at the level of intracellular pathways activated …

Thermal Conductivity Improvement In Carbon Nanoparticle Doped Pao Oil: An Experimental Study, Shadab Shaikh, Khalid Lafdi, Rengasamy Ponnappan

Chemical and Materials Engineering Faculty Publications

The present work involves a study on the thermal conductivity of nanoparticle-oil suspensions for three types of nanoparticles, namely, carbon nanotubes(CNTs), exfoliated graphite (EXG), and heat treated nanofibers (HTT) with PAO oil as the base fluid. To accomplish the above task, an experimental analysis is performed using a modern light flash technique (LFA 447) for measuring the thermal conductivity of the three types of nanofluids, for different loading of nanoparticles.

The experimental results show a similar trend as observed in literature for nanofluids with a maximum enhancement of approximately 161% obtained for the CNT-PAO oil suspension. The overall percent enhancements …

Experimental Study On The Influence Of Foam Porosity And Pore Size On The Melting Of Phase Change Materials, Khalid Lafdi, Osama Mesalam Mesalhy, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

Experimental study was carried out to study the phase change heat transfer within a composite of phase change material (PCM) infiltrated high thermal conductivity foam. An experimental setup was built to measure the temperature profiles and capture the melting evolution of the PCM inside aluminum foams. Aluminum foams were used as the porous material, and low melting temperature paraffin wax was used as the PCM. It was observed from the results that the system parameters of the wax/foam composite had a significant influence on its heat transfer behavior.

By using higher porosity aluminum foam, the steady-state temperature was reached faster …

Effect Of Carbon Nanofiber Heat Treatment On Physical Properties Of Polymeric Nanocomposites—Part I, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

The definition of a nanocomposite material has broadened significantly to encompass a large variety of systems made of dissimilar components and mixed at the nanometer scale. The properties of nanocomposite materials also depend on the morphology, crystallinity, and interfacial characteristics of the individual constituents. In the current work, vapor-grown carbon nanofibers were subjected to varying heat-treatment temperatures.

The strength of adhesion between the nanofiber and an epoxy (thermoset) matrix was characterized by the flexural strength and modulus. Heat treatment to 1800C∘ demonstrated maximum improvement in mechanical properties over that of the neat resin, while heat-treatment to higher temperatures demonstrated a …

Interfacial And Capillary Pressure Effects On The Thermal Performance Of Wax/Foam Composites, Mohammad Rajab Almajali, Khalid Lafdi, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

A numerical investigation study was performed to study the phase change behavior of wax/foam composite encapsulated in an aluminum casing. Two types of foam materials, namely, aluminum and carbon, were infiltrated with paraffin wax. The progress of melt interface and temperature distribution within the encapsulated composite was analyzed using computational fluid dynamics software (CFD). A two-energy equation model was implemented in the CFD software through the use of user-defined function (UDF). Interfacial effects influencing the heat transfer process at the casing-composite junction and between the wax-foam surfaces within the composite were addressed through the use of separate UDF. In addition, …

Oxygen Plasma Treatment And Deposition Of Cnx On A Fluorinated Polymer Matrix Composite For Improved Erosion Resistance, Christopher Muratore, Andras Korenyi-Both, John E. Bultman, A. R. Waite, John G. Jones, T. M. Storage, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CNx coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CNx was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relative to the …

Demonstration Of Magnetoelectric Scanning Probe Microscopy, Jason R. Hattrick-Simpers, Liyang Dai, Manfred Wuttig, Ichiro Takeuchi, Eckhard Quandt

Faculty Publications

A near-field room temperature scanning magnetic probe microscope has been developed using a laminated magnetoelectric sensor. The simple trilayer longitudinal-transverse mode sensor, fabricated using Metglas as the magnetostrictive layer and polyvinylidene fluoride as the piezoelectric layer, shows an ac field sensitivity of 467±3μV∕O_e in the measured frequency range of 200Hz–8kHz. The microscope was used to image a 2mm diameter ring carrying an ac current as low as 10⁻⁵A. ac fields as small as 3×10⁻¹⁰T have been detected.

The Microstructure And Grain Size Of Jet Electroplated Copper Films In Damascene Trench Features, Andrew Tzanavaras, Gregory Young, Stacy H. Gleixner

Faculty Publications

The brightening additive level and dc current density of electroplating baths are two parameters that affect the gap-filling capability and the degree of impurity incorporation in electroplated copper films. Additive incorporation can inhibit grain growth during the room temperature recrystallization process and therefore affect the final grain size. This investigation explores the grain size and microstructure of dc jet-electroplated copper films in 0.35 and 0.50μm Damascene trenches as a function of current density and brightening additive level after first receiving a high-temperature anneal. Unlike a previous study that explored these variables in blanket Cu films [ J. Electrochem. Soc. , …

Intracellular Signaling Networks In The Immune Response: Pathways Activated By Interleukin-2 And-4 Receptors And Their Roles In T Cell Proliferation, Kristen K. Comfort

Chemical and Materials Engineering Faculty Publications

Cells sense and respond to chemical and physical stimuli through signal transduction pathways, which mediate cell proliferation, differentiation, migration, and survival. The cytokines interleukin-2 (IL-2) and interleukin-4 (IL-4) are key regulators of the adaptive immune system, particularly influencing the clonal expansion and differentiation of T cells. At least in culture, both synergistic and antagonistic effects of IL-2 and -4 co-stimulation have been reported; the antagonism, when observed, is thought to arise from the utilization of a common subunit shared by IL-2 and IL-4 receptors. We have sought to characterize IL-2 and IL-4 signaling at the level of intracellular pathways activated …

Control Of Plasma Flux Composition Incident On Tin Films During Reactive Magnetron Sputtering And The Effect On Film Microstructure, Christopher Muratore, Scott G. Walton, Darrin Leonhardt, Richard F. Fernsler

Chemical and Materials Engineering Faculty Publications

A hybrid plasma enhanced physical vapor deposition (PEPVD) system consisting of an unbalanced dc magnetron and a pulsed electron beam-produced plasma was used to deposit reactively sputtered titanium nitride thin films. The system allowed for control of the magnitudes of the ion and neutral flux, in addition to the type of nitrogen ions (atomic or molecular) that comprised the flux. For all deposition experiments, the magnitude of the ion flux incident on the substrate was held constant, but the composition of the total flux was varied. X-ray diffraction and atomic force microscopy showed that crystallographic texture and surface morphology of …

Combinatorial Study Of Ni-Ti-Pt Ternary Metal Gate Electrodes On Hfo2 For The Advanced Gate Stack, K.-S. Chang, M. L. Green, J. Suehle, E. M. Vogel, H. Xiong, Jason R. Hattrick-Simpers, I. Takeuchi, O. Famodu, K. Ohmori, P. Ahmet, T. Chikyow, P. Majhi, B.-H. Lee, M. Gardner

Faculty Publications

The authors have fabricated combinatorial Ni–Ti–Pt ternary metal gate thin film libraries on HfO₂ using magnetron co-sputtering to investigate flatband voltage shift (ΔV_fb) , work function (Φ_m) , and leakage current density (J_L) variations. A more negative ΔV_fb is observed close to the Ti-rich corner than at the Ni- and Pt-rich corners, implying smaller Φ_m near the Ti-rich corners and higher Φ_m near the Ni- and Pt-rich corners. In addition, measured J_L values can be explained consistently with the observed Φ_m variations. Combinatorial methodologies prove to be useful …

The Grain Size And Microstructure Of Jet-Electroplated Damascene Copper Films, Stacy H. Gleixner, Andrew Tzanavaras, Gregory Young

Faculty Publications

Electroplated damascene copper is rapidly replacing aluminum-copper alloys for on-chip interconnect metallization in advanced ultralarge scale integrated (ULSI) semiconductor devices. In addition to a high degree of (111) crystallographic texture, large defect-free grains are desired to enhance the performance and reliability of copper interconnects in such devices. The brightening additive level and dc current density of electroplating baths are two parameters that affect the process gap-filling capability and the degree of additive incorporation in these copper films. Additive incorporation can inhibit grain growth during the room-temperature recrystallization process and therefore affect the final grain size in electroplated copper films. This …