Open Access. Powered by Scholars. Published by Universities.®

Biochemical and Biomolecular Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2022

Discipline
Institution
Keyword
Publication
Publication Type

Articles 31 - 60 of 66

Full-Text Articles in Biochemical and Biomolecular Engineering

Analysis Of Sequential Adsorption-Oxidation Of Vocs On Atomic Layer-Deposited Ptni/Zro2-Sio2dual-Function Materials, Busuyi O. Adebayo, Han Yu, Ali A. Rownaghi, Xinhua Liang, Fateme Rezaei Jul 2022

Analysis Of Sequential Adsorption-Oxidation Of Vocs On Atomic Layer-Deposited Ptni/Zro2-Sio2dual-Function Materials, Busuyi O. Adebayo, Han Yu, Ali A. Rownaghi, Xinhua Liang, Fateme Rezaei

Chemical and Biochemical Engineering Faculty Research & Creative Works

To develop efficient dual-function materials (DFMs) for capture and destruction of volatile organic compounds (VOCs), we prepared a series of composite materials comprising PtNi nanoparticles supported on ZrO2-promoted SiO2(PtNi/ZrO2-SiO2) via atomic layer deposition (ALD) method and investigated them for sequential adsorption and desorption/catalytic oxidation of benzene, as a model VOC compound. ZrO2was first deposited on a unimodal SiO2support, followed by deposition of Pt and Ni nanoparticles with varried amount. Dynamic adsorption experiments were conducted using a 500 ppmv-laden feed at 25 °C and 1 atm, followed by in …


Scale Up Of A Novel Method To Maximize Malonyl-Coa In Escherichia Coli, Clifford Harris Leblanc Iv Jul 2022

Scale Up Of A Novel Method To Maximize Malonyl-Coa In Escherichia Coli, Clifford Harris Leblanc Iv

LSU Master's Theses

The instability of oil’s price along with its limited availability and impact on the environment motivate the search for an alternative feedstock that can sustain the profitability of chemical companies. Industrial biotechnology can promote renewable sources of energy and products by using microorganisms to produce a wide range of chemical compounds. The three-carbon metabolite, malonyl-CoA, can serve as a precursor to a variety of industrial chemicals. The major hurdle with using malonyl-CoA in industry is that its intracellular concentration in Escherichia Coli is very low. Previous attempts to increase the intracellular level of malonyl-CoA have ranged from genetic engineering of …


Experimentation And Correlation Development Of Mass Transfer In A Mimicked Fischer–Tropsch Slurry Bubble Column Reactor, Lu Han, Mahmoud M. Taha, Premkumar Kamalanathan, Nora Y. Selem, Muthanna H. Al-Dahhan Jul 2022

Experimentation And Correlation Development Of Mass Transfer In A Mimicked Fischer–Tropsch Slurry Bubble Column Reactor, Lu Han, Mahmoud M. Taha, Premkumar Kamalanathan, Nora Y. Selem, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Gas–liquid volumetric mass transfer coefficient "kLa " for CH4, CO2, and Ar were experimentally measured at different conditions in a mimicked Fischer–Tropsch (FT) slurry bubble column reactor by using a non-invasive gaseous tracer technique and the axial dispersion model. Results validate the square root relation, between kLa and diffusivity "Dg", that can be used to predict kLa for different species with k La values available in the literature. Additionally, Higbie's penetration theory was adopted along with bubble dynamics parameters estimation to develop a correlation for predicting kL …


Effect Of Arginine And Nano-Hydroxyapatite Application On The Hypersensitivity And Color Change Of Bleached Enamel: A Randomized Controlled Clinical Trial, Lamiaa M. Moharam, Sherif Khadr, Ahmed Abdou, Shaymaa M. Nagi Jun 2022

Effect Of Arginine And Nano-Hydroxyapatite Application On The Hypersensitivity And Color Change Of Bleached Enamel: A Randomized Controlled Clinical Trial, Lamiaa M. Moharam, Sherif Khadr, Ahmed Abdou, Shaymaa M. Nagi

Chemical and Biochemical Engineering Faculty Research & Creative Works

Background: To evaluate the effect of 2.5% Arginine and nano-hydroxyapatite (nHA) application on the post-bleaching hypersensitivity (HS) and color change in a randomized controlled trial. Material and Methods: Sixty-four participants were randomly allocated to four groups (n=16) according to the investigated desensitizing agents (UltraEZ gel, experimental 2.5% Arginine, 2.5% nHA pastes and control (no treatment) groups). An in-office chemical bleaching agent (40% hydrogen peroxide) was used for vital bleaching of the anterior teeth. The desensitizing agents were applied to the assigned groups and left for 30 min then rinsed off the teeth. HS was evaluated using Visual Analogue Scale (VAS) …


Porcine Liver Injury Model To Assess Tantalum-Containing Bioactive Glass Powders For Hemostasis, Malvika Nagrath, Danielle Bince, Corwyn Rowsell, Deanna Polintan, Joao Rezende-Neto, Mark R. Towler Jun 2022

Porcine Liver Injury Model To Assess Tantalum-Containing Bioactive Glass Powders For Hemostasis, Malvika Nagrath, Danielle Bince, Corwyn Rowsell, Deanna Polintan, Joao Rezende-Neto, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

This study evaluates compositions of tantalum-containing mesoporous bioactive glass (Ta-MBG) powders using a porcine fatal liver injury model. The powders based on (80-x)SiO2-15CaO-5P2O5-xTa2O5 compositions with x = 0 (0Ta/Ta-free), 1 (1Ta), and 5 (5Ta) mol% were made using a sol–gel process. A class IV hemorrhage condition was simulated on the animals; hemodynamic data and biochemical analysis confirmed the life-threatening condition. Ta-MBGs were able to stop the bleeding within 10 min of their application while the bleeds in the absence of any intervention or in the presence of a commercial agent, AristaTM …


Engineering Metal-Oxide Interface By Depositing Zro2 Overcoating On Ni/Al2o3 For Dry Reforming Of Methane, Baitang Jin, Shiguang Li, Yuzi Liu, Xinhua Liang May 2022

Engineering Metal-Oxide Interface By Depositing Zro2 Overcoating On Ni/Al2o3 For Dry Reforming Of Methane, Baitang Jin, Shiguang Li, Yuzi Liu, Xinhua Liang

Chemical and Biochemical Engineering Faculty Research & Creative Works

Zirconium oxide (ZrO2) was deposited onto Ni/Al2O3 catalyst as overcoating by atomic layer deposition (ALD) for dry reforming of methane (DRM). High-temperature heating during H2-reduction could transform the ALD-prepared ZrO2 thin film to tetragonal phase and crack the encapsulating layer on Ni sites, which constructed a beneficial Ni-ZrOx interface. Interfacial surface oxygen vacancies on ZrO2 overcoating were induced by the partial reduction of ZrO2 surface during high-temperature H2 reduction, with the assistance of Ni. During DRM, the interfacial oxygen vacancies enhanced CO2 activation by dissociating CO2 …


Study Of Gas Holdup Distribution In Cylindrical Split Airlift Reactor By Using Gamma-Ray Densitometry (Grd), Abbas J. Sultan, Laith S. Sabri, Hasan Shakir Majdi, Shadha K. Jebur, Muthanna H. Al-Dahhan May 2022

Study Of Gas Holdup Distribution In Cylindrical Split Airlift Reactor By Using Gamma-Ray Densitometry (Grd), Abbas J. Sultan, Laith S. Sabri, Hasan Shakir Majdi, Shadha K. Jebur, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

The local gas holdup details and behaviors in the cylindrical split airlift column by using an unconventional gamma-ray densitometry (GRD) measurement in non-invasive manner technique was investigated for the first time in this work for such kind of airlift column. With different gas velocities, 1, 2, and 3 cm/s, at three various axial planes (different levels) in z = 3, 60, and 110 cm were studied for local distribution in radial gas holdup profiles. The distribution in gas–liquid phases (air-water system) in the entire split reactor column, in the rising and descending sides, including their behavior in the upper and …


Process Evaluation And Kinetic Analysis Of 3d-Printed Monoliths Comprised Of Cao And Cr/H-Zsm-5 In Combined Co2 Capture-C2h6 Oxidative Dehydrogenation To C2h4, Khaled Baamran, Shane Lawson, Ali A. Rownaghi, Fateme Rezaei May 2022

Process Evaluation And Kinetic Analysis Of 3d-Printed Monoliths Comprised Of Cao And Cr/H-Zsm-5 In Combined Co2 Capture-C2h6 Oxidative Dehydrogenation To C2h4, Khaled Baamran, Shane Lawson, Ali A. Rownaghi, Fateme Rezaei

Chemical and Biochemical Engineering Faculty Research & Creative Works

In this study, dual-function materials (DFMs) comprised of CaO and Cr/H-ZSM-5 were formulated in 3D-printed monolithic structures and investigated in a combined process for capture and utilization of CO2 in oxidative dehydrogenation of C2H6 to C2H4 (CO2-ODHE). Various formulation strategies were employed to fabricate these DFM structures. Two bed designs were considered: i) a layered-bed in which adsorbent (CaO) and catalyst were printed separately and stacked on top of each other, and ii) a single-layer bed where the adsorbent-catalyst materials were 3D-printed into a singular monolith and loaded into the bed …


Integration Of Dynamic Growth Modeling And Hydrodynamics In An Internal-Loop Split Photobioreactor, Laith S. Sabri, Aastha Ojha, Abbas J. Sultan, Muthanna H. Aldahhan May 2022

Integration Of Dynamic Growth Modeling And Hydrodynamics In An Internal-Loop Split Photobioreactor, Laith S. Sabri, Aastha Ojha, Abbas J. Sultan, Muthanna H. Aldahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

In this study, new high-quality experimental data for culturing green microalgae Scenedesmus in tubular and cylindrical split airlift photobioreactors were obtained under different operating conditions. The obtained experimental data of culturing microalgae Scenedesmus in a tubular photobioreactor were used for determining the kinetic parameters of the photosynthetic reaction. On the other hand, the culturing of green microalgae in a split airlift photobioreactor was used to measure the microalgae cell trajectory using an advanced radioactive particle tracking (RPT) technique. The obtained results in terms of kinetic parameters of the photosynthetic reaction and microalgae cell trajectory were integrated for the first time …


Random Trilobe Packing Using Rigid Body Approach And Local Gas-Liquid Hydrodynamics Simulation Through Cfd With Experimental Validation, Binbin Qi, Sebastián Uribe, Omar Farid, Muthanna H. Al-Dahhan May 2022

Random Trilobe Packing Using Rigid Body Approach And Local Gas-Liquid Hydrodynamics Simulation Through Cfd With Experimental Validation, Binbin Qi, Sebastián Uribe, Omar Farid, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

It is quite difficult to measure the local information of the gas/liquid flow inside random packed extrudate catalyst beds in a large scale. Obtaining the local information through computational fluid dynamic (CFD) simulations in such system is also difficult due to the complexity of random particle packing and two-phase flow simulation. An efficient packing scheme was implemented to randomly pack 2917 trilobe particles (10 cm in height) in a 2-inch column to represent the trickle bed reactor (TBR) based on the rigid body approach. The generated geometry was used to define the computational domain for the two-phase hydrodynamics simulation based …


Review Of Biomechanical Studies And Finite Element Modeling Of Sternal Closure Using Bio-Active Adhesives, Amatulraheem Al-Abassi, Marcello Papini, Mark R. Towler May 2022

Review Of Biomechanical Studies And Finite Element Modeling Of Sternal Closure Using Bio-Active Adhesives, Amatulraheem Al-Abassi, Marcello Papini, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

The most common complication of median sternotomy surgery is sternum re-separation after sternal fixation, which leads to high rates of morbidity and mortality. The adhered sternal fixation technique comprises the wiring fixation technique and the use of bio-adhesives. Adhered sternal fixation techniques have not been extensively studied using finite element analysis, so mechanical testing studies and finite element analysis of sternal fixation will be presented in this review to find the optimum techniques for simulating sternal fixation with adhesives. The optimal wiring technique should enhance bone stability and limit sternal displacement. Bio-adhesives have been proposed to support sternal fixation, as …


Establishing Pteridine Metabolism In A Progressive Isogenic Breast Cancer Cell Model – Part Ii, Lindsey Rasmussen, Zachary Foulks, Jiandong Wu, Casey Burton, Honglan Shi May 2022

Establishing Pteridine Metabolism In A Progressive Isogenic Breast Cancer Cell Model – Part Ii, Lindsey Rasmussen, Zachary Foulks, Jiandong Wu, Casey Burton, Honglan Shi

Chemistry Faculty Research & Creative Works

Introduction: Determining the biological significance of pteridines in cancer development and progression remains an important step in understanding the altered levels of urinary pteridines seen in certain cancers. Our companion study revealed that several folate-derived pteridines and lumazines correlated with tumorigenicity in an isogenic, progressive breast cancer cell model, providing direct evidence for the tumorigenic origin of pteridines. Objectives: This study sought to elucidate the pteridine biosynthetic pathway in a progressive breast cancer model via direct pteridine dosing to determine how pteridine metabolism changes with tumorigenicity. Methods: First, MCF10AT breast cancer cells were dosed individually with 15 pteridines to determine …


Drug-Facilitated Sexual Assault At The University Of Arkansas, Barrett Weidman May 2022

Drug-Facilitated Sexual Assault At The University Of Arkansas, Barrett Weidman

Chemical Engineering Undergraduate Honors Theses

This work was written to fulfill two main purposes. First, to help survivors of Drug-Facilitated Sexual Assault (DFSA) process their experience by compiling the toxicological, pharmacological, and distribution of the three most used date-rape drugs. Second, to gauge the knowledge and interest of University of Arkansas students regarding drug impairments, sexual assault education, and bystander intervention training. A survey was conducted for the latter and revealed that 91.6% of students believe the University’s existing sexual assault prevention education and bystander intervention training have room for improvement. Also, 37.1% of students who have received this education report that the programming does …


Isolation And Production Of Tandem Collagen Binding Domain From Clostridial Collagenase Colg And Developments In C1q Reagent Production For Future Molecule Characterization Work, Stephanie Beitle May 2022

Isolation And Production Of Tandem Collagen Binding Domain From Clostridial Collagenase Colg And Developments In C1q Reagent Production For Future Molecule Characterization Work, Stephanie Beitle

Chemical Engineering Undergraduate Honors Theses

This thesis covers a two part project: the production methods to create a double collagen binding domain molecule with a growth factor for wound healing applications and the development of a new in-house production method for isolating C1q from bovine blood. The wound healing molecule was created using transformation, sonication, and purification before being tested via electrophoresis SDS page and Western blots to confirm the molecule’s presence. The C1q in-house production method utilizes an ultrafiltration flow cell rather than dialysis at a critical point in the process, allowing for researchers to not only be able to use a single small …


Erythrocyte Deformability In Response To Glucose Using Liquid Crystals, Jayden Goff May 2022

Erythrocyte Deformability In Response To Glucose Using Liquid Crystals, Jayden Goff

Biomedical Engineering Undergraduate Honors Theses

The worldwide prevalence of diabetes mellitus is rapidly increasing with about 9.3% of the adult population living with the disease. People with diabetes have trouble regulating their blood glucose levels which typically leads to hyperglycemia. Under normal physiological conditions, erythrocytes can undergo deformations in response to shear stress when passing through capillaries with a smaller diameter. Poorly managed hyperglycemia can lead to the glycosylation of erythrocyte membrane proteins and hemoglobin. This glycosylation leads to increased rigidity of the cells along with decreased deformability in response to mechanical stress; therefore, these cells have a higher susceptibility of getting stuck in the …


Recovery Of Degraded Ni-Rich Nmc811 Particles For Lithium-Ion Batteries, Han Yu, Yan Gao, James Kirtley, Gabriel Borgmeyer, Xiaoqing He, Xinhua Liang May 2022

Recovery Of Degraded Ni-Rich Nmc811 Particles For Lithium-Ion Batteries, Han Yu, Yan Gao, James Kirtley, Gabriel Borgmeyer, Xiaoqing He, Xinhua Liang

Chemical and Biochemical Engineering Faculty Research & Creative Works

Nickel-rich cathode materials attract a lot of attention due to their high energy density. However, their sensitivity to air and moisture hinders their practical applications. Exposing Ni-rich NMC in the air will produce by-products that are not conducive to lithium-ion transmission. Water washing can be used to remove by-products on the surface, but it can also introduce new problems, such as the generation of NiO on the particle surface, which will reduce the electrochemical performance of the material. In this study, Al2O3atomic layer deposition (ALD) was applied on degraded NMC811 particles to recover the electrochemical performance …


Effects Of Continuous In Situ Low-Dose Ionizing Radiation On Microorganisms, Molly E. Wintenberg May 2022

Effects Of Continuous In Situ Low-Dose Ionizing Radiation On Microorganisms, Molly E. Wintenberg

All Dissertations

Precise detection and monitoring of nuclear fuel cycle, enrichment, and weapon development activities are critical for supporting warfighter preparation in chemical, biological, radiological, nuclear, and explosives (CBRNE) operations, clandestine activities, and nuclear compliance. A biological sensing system could serve as an alternative to traditional detection methods by using organic material naturally present in the environment to discreetly detect residual trace nuclear material. Microorganisms provide an optimal platform for an alternative sensing system; however, their response to low levels of ionizing radiation is poorly characterized. Combining the power of next-generation sequencing and transcriptomic analysis, this dissertation takes an approach to obtain …


Feasibility Study Of Implementing Gamma-Ray Computed Tomography On Measuring Aggregate Distribution And Radiation Shielding Properties Of Concrete Samples, Omar Farid, Nima Farzadnia, Kamal Khayat, Muthanna H. Al-Dahhan Apr 2022

Feasibility Study Of Implementing Gamma-Ray Computed Tomography On Measuring Aggregate Distribution And Radiation Shielding Properties Of Concrete Samples, Omar Farid, Nima Farzadnia, Kamal Khayat, Muthanna H. Al-Dahhan

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Aggregate segregation is one of the key defects that impair the performance of concrete at fresh and hardened stages. This study aims to assess the feasibility of using an advanced technique to identify/scan/determine the aggregate segregation of concrete elements and determine radiation shielding properties of the concrete. The gamma-ray computed tomography (γ-CT) technique was employed to study aggregate distribution/dispersion in self-consolidating concrete (SCC). Accordingly, two SCC mixtures with moderate segregation (MS) and high segregation (HS) levels were cast and compared with highly stable SCC with no segregation (NS). The γ-CT scans were located on three different levels of concrete specimens …


Reactive Oxygen Species (Ros)-Responsive Size-Reducible Nanoassemblies For Deeper Atherosclerotic Plaque Penetration And Enhanced Macrophage-Targeted Drug Delivery, Jianhua He, Wenli Zhang, Xiaoju Zhou, Fengfei Xu, Jiahui Zou, Qiqi Zhang, Yi Zhao, Hongliang He, Hu Yang, Jianping Liu Apr 2022

Reactive Oxygen Species (Ros)-Responsive Size-Reducible Nanoassemblies For Deeper Atherosclerotic Plaque Penetration And Enhanced Macrophage-Targeted Drug Delivery, Jianhua He, Wenli Zhang, Xiaoju Zhou, Fengfei Xu, Jiahui Zou, Qiqi Zhang, Yi Zhao, Hongliang He, Hu Yang, Jianping Liu

Chemical and Biochemical Engineering Faculty Research & Creative Works

Nanoparticle-based therapeutics represent potential strategies for treating atherosclerosis; however, the complex plaque microenvironment poses a barrier for nanoparticles to target the dysfunctional cells. Here, we report reactive oxygen species (ROS)-responsive and size-reducible nanoassemblies, formed by multivalent host-guest interactions between β-cyclodextrins (β-CD)-anchored discoidal recombinant high-density lipoprotein (NP3ST) and hyaluronic acid-ferrocene (HA-Fc) conjugates. The HA-Fc/NP3ST nanoassemblies have extended blood circulation time, specifically accumulate in atherosclerotic plaque mediated by the HA receptors CD44 highly expressed in injured endothelium, rapidly disassemble in response to excess ROS in the intimal and release smaller NP3ST, allowing for further …


Model-Guided Design Of Rna-Based Synthetic Circuits For The Dynamic Regulation Of Gene Expression, Jordan R. Ryan Apr 2022

Model-Guided Design Of Rna-Based Synthetic Circuits For The Dynamic Regulation Of Gene Expression, Jordan R. Ryan

LSU Master's Theses

A longstanding goal in synthetic biology has been to build synthetic gene circuits with the ability to harness nature’s capability of precise gene expression regulation. Advancements in RNA technology have established RNA-based regulators with distinct advantages over traditional protein-based regulators such as faster signal propagation, versatile programmability, and low cellular burden, which has created an interest in the field to construct innovative synthetic gene circuits using de novo RNA- based regulators. However, our understanding of the behavior and kinetics of RNA-RNA interactions for the construction of gene circuits is incomplete. This thesis proposes a model-guided design framework that integrates mechanistic …


Photo-Induced Drug Release From Polymeric Micelles And Liposomes: Phototriggering Mechanisms In Drug Delivery Systems, Najla M. Salkho, Nahid S. Awad, William G. Pitt, Ghaleb A. Husseini Mar 2022

Photo-Induced Drug Release From Polymeric Micelles And Liposomes: Phototriggering Mechanisms In Drug Delivery Systems, Najla M. Salkho, Nahid S. Awad, William G. Pitt, Ghaleb A. Husseini

Faculty Publications

Chemotherapeutic drugs are highly effective in treating cancer. However, the side effects associated with this treatment lower the quality of life of cancer patients. Smart nanocarriers are able to encapsulate these drugs to deliver them to tumors while reducing their contact with the healthy cells and the subsequent side effects. Upon reaching their target, the release of the encapsulated drugs should be carefully controlled to achieve therapeutic levels at the required time. Light is one of the promising triggering mechanisms used as external stimuli to trigger drug release from the light-responsive nanocarriers. Photo-induced drug release can be achieved at a …


Tuning Electrochemical Interactions And Polymer Electrolyte Interfaces For Enhanced Organic Acid Separations Using Electrodeionization, Matthew Leo Jordan Mar 2022

Tuning Electrochemical Interactions And Polymer Electrolyte Interfaces For Enhanced Organic Acid Separations Using Electrodeionization, Matthew Leo Jordan

LSU Doctoral Dissertations

Chemical separations are critical processes for chemical and industrial plants to purify and isolate products however current separation technologies, such as distillation, rely on energy intensive processes. Electrochemical separation processes, such as electrodialysis and electrodeionization, are an energy efficient alternative that are emerging as an alternative for thermal-based separations. Organic acids are weakly ionizable species and susceptible for purification from process streams using electrochemical processes. Recently the fermentation route has garnered greater attention as a means for producing value-added chemicals, such as organic acids, from a renewable feedstock and aiding the circular economy. Some of the challenges electrodialysis faces for …


Protocol To Engineer Nanofilms Embedded Lipid Nanoparticles For Controlled And Targeted Drug Delivery (Nectar), Rashi Porwal, Stephen L. Hayward, Srivatsan Kidambi Mar 2022

Protocol To Engineer Nanofilms Embedded Lipid Nanoparticles For Controlled And Targeted Drug Delivery (Nectar), Rashi Porwal, Stephen L. Hayward, Srivatsan Kidambi

Department of Chemical and Biomolecular Engineering: Faculty Publications

We present a protocol to engineer a substrate-mediated delivery platform comprising hyaluronic acid-coated lipid nanoparticles (HALNPs) embedded into polyelectrolyte multilayer (PEM) films. This platform allows controlled spatiotemporal release of lipid nanoparticles (LNP) by embedding them within the polyelectrolyte multilayer films matrix. HALNP conjugate with antibodies also adds the ability for targeted delivery. The use of LNP enables this platform to encapsulate both hydrophobic and hydrophilic drugs. This platform can easily be reproduced and utilized for various biomedical drug delivery applications. For complete details on the use and execution of this protocol, please refer to Hayward et al. (2015, 2016a, 2016b), …


Influence Of Saccharide Modifications On Heparin Lyase Iii Substrate Specificities, Jiandong Wu, Pradeep Chopra, Geert Jan Boons, Joseph Zaia Mar 2022

Influence Of Saccharide Modifications On Heparin Lyase Iii Substrate Specificities, Jiandong Wu, Pradeep Chopra, Geert Jan Boons, Joseph Zaia

Chemical and Biochemical Engineering Faculty Research & Creative Works

A Library of 23 Synthetic Heparan Sulfate (HS) Oligosaccharides, Varying in Chain Length, Types, and Positions of Modifications, Was Used to Analyze the Substrate Specificities of Heparin Lyase III Enzymes from Both Flavobacterium Heparinum and Bacteroides Eggerthii. the Influence of Specific Modifications, Including N-Substitution, 2-O Sulfation, 6-O Sulfation, and 3-O Sulfation on Lyase III Digestion Was Examined Systematically. It Was Demonstrated that Lyase III from Both Sources Can Completely Digest Oligosaccharides Lacking O-Sulfates. 2-O Sulfation Completely Blocked Cleavage at the Corresponding Site; 6-O and 3-O Sulfation on Glucosamine Residues Inhibited Enzyme Activity. We Also Observed that There Are Differences in …


Torrefaction Of Oil Palm Empty Fruit Bunch Biomass, Mohamad Azri Sukiran Feb 2022

Torrefaction Of Oil Palm Empty Fruit Bunch Biomass, Mohamad Azri Sukiran

Student Works (2020-2029)

Empty fruit bunches (EFB) have great potential to be used as a renewable fuel. Its current low rate of utilization due largely to high moisture content and low calorific value (CV) can be overcome via a thermal pretreatment namely torrefaction. This study investigated the effects of torrefaction temperature, residence time, particle size and moisture content on EFB’s final products distribution and their characteristics in a fixed bed reactor. The solid products (torrefied EFB) obtained were analyzed by various methods such as proximate and ultimate analyses, CV, scanning electron microscopy (SEM), Fourier transform infrared (FTIR), x-ray diffraction (XRD) and thermogravimetric analysis …


Examining The Effect Of A Chitosan Biopolymer On Alkali-Activated Inorganic Material For Aqueous Pb(Ii) And Zn(Ii) Sorption, Sukanta K. Mondal, Chenglin Wu, Felix C. Nwadire, Ali A. Rownaghi, Aditya Kumar, Yusuf Adewuyi, Monday Uchenna Okoronkwo Jan 2022

Examining The Effect Of A Chitosan Biopolymer On Alkali-Activated Inorganic Material For Aqueous Pb(Ii) And Zn(Ii) Sorption, Sukanta K. Mondal, Chenglin Wu, Felix C. Nwadire, Ali A. Rownaghi, Aditya Kumar, Yusuf Adewuyi, Monday Uchenna Okoronkwo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Biopolymers and alkali-activated materials have attracted a great deal of attention as adsorbents for the removal of heavy metal contaminants from aqueous solutions. Both materials are sustainable and feature unique properties, but biopolymers are relatively more expensive or difficult to prepare and exhibit low mechanical and surface properties, a narrow pH range, and thermal stability. In this study, hybrid adsorbents were prepared from both types of material, by alkali activation of low-cost fly ash precursors accompanied by incorporation of 0-2%mass chitosan biopolymer. Two types of alkaline activating solutions, NaOH and Na2SiO3, were employed to generate two sets of hybrid adsorbents …


Recent Advancements In Electrochemical Conversion Of Carbon Dioxide, Nandan Nag, Amit Kumar, Sumit Sharma, Sandeep Kumar, Amit K. Thakur Jan 2022

Recent Advancements In Electrochemical Conversion Of Carbon Dioxide, Nandan Nag, Amit Kumar, Sumit Sharma, Sandeep Kumar, Amit K. Thakur

Civil & Environmental Engineering Faculty Publications

Electrochemical reduction of carbon dioxide into eco-friendly and clean products is a promising approach to eradicate pollution. Although carbon dioxide emission is inhibited by the advent of renewable sources of energy, it is present in the atmosphere and needs to be cleaned. The reduction of carbon dioxide from atmospheric gases can be accomplished by its adsorption and subsequent transportation to electrolytic chambers, where it is reduced to hydrocarbons, organic acids or carbonates. This review focuses on developing a three compartment electrochemical cell to reduce carbon dioxide used as a catholyte. Various factors affecting the electrochemical reduction of carbon dioxide and …


Effect Of Açai Berry Extract Application On The Bond Strength To The Bleached Enamel Using An Experimental Etch-And-Rinse Adhesive, Lamiaa M. Moharam, Haidy N. Salem, Shahinaz N. Hassan Jan 2022

Effect Of Açai Berry Extract Application On The Bond Strength To The Bleached Enamel Using An Experimental Etch-And-Rinse Adhesive, Lamiaa M. Moharam, Haidy N. Salem, Shahinaz N. Hassan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Background: To evaluate the bleached enamel shear bond strength (SBS) after antioxidants application using an experimental adhesive. Material and Methods: Sixty sound human molars had their roots removed then cut into buccal and lingual halves and mounted in acrylic blocks. Enamel bleaching was done using an in-office chemical bleaching agent. Specimens were arbitrarily allocated into 12 groups (n=10) regarding the three experimental levels of the study: two antioxidant agents [10% açai berry extract, 10% sodium ascorbate prepared gels (applied for 15-min) and the control group (no antioxidant application)], two adhesive materials [commercial etch-and-rinse (ER) adhesive and an experimental ER adhesive] …


Austenitic, Duplex, And Lean Duplex Stainless Steel Critical Pitting Temperature In Simulated Concrete Environment, Bobby Giebel Jan 2022

Austenitic, Duplex, And Lean Duplex Stainless Steel Critical Pitting Temperature In Simulated Concrete Environment, Bobby Giebel

Williams Honors College, Honors Research Projects

In this work, the critical pitting temperature (CPT) will be observed for a selection of austenitic (316LN and 24100) and duplex (2205), and lean duplex (2304, 2001) stainless steels in simulated concrete pore solution. To study the influence of temperature on the pitting stability of the stainless steels, three temperatures were tested: 25oC, 45oC, and 65oC for cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS). Electrochemical properties of the interfaces we studied via EIS analysis. Kinetics were studied via CPP testing. To reveal the critical pitting temperature of the stainless steels, cyclic thermammetry was used. Characterization of the pits …


Amino-Polymer For Co2 Capture By Vacuum Swing Adsorption, Sean Billy Jan 2022

Amino-Polymer For Co2 Capture By Vacuum Swing Adsorption, Sean Billy

Williams Honors College, Honors Research Projects

The applications of sorbent compounds in conjunction with amines and other additives is an innovative method at combating CO2 pollution. An ideal solution would use an amine sorbent to trap the high levels of absorbed CO2 with a low binding energy (less than 45 kJ/mol) and subsequently release them into a stored vessel at ambient temperature with a vacuum swing adsorption system. Attempts at finding a best mixture will be conducted through the usage of a vacuum swing system, utilizing a bed syringe containing the sorbent mix and a vacuum syringe to pull on and subsequently release the CO2 into …