Chemical Engineering Commons^™

Review Of Fuzzy Models And Fuzzy Methods For Analysis Of Information In Conditions Of Emotional Decision Making, Latafat Gardashova, Royal Shirinov, Diana Boqdanova

Chemical Technology, Control and Management

In the modern world, decision-making often takes place in an environment of uncertainty and under the significant influence of emotional factors, which requires the use of special methods for analyzing information. This study is devoted to an overview of fuzzy models and methods that allow such factors to be taken into account when making decisions. In particular, the approaches based on fuzzy logic, fuzzy cognitive maps and fuzzy clustering methods that provide flexibility and adaptability in conditions of uncertainty are considered. The study analyzes examples of the application of these methods in various fields, including risk management, medical diagnostics and …

Addressing Strain And Porosity Changes Of Battery Electrodes Due To Reversible Expansion Through Dem Simulations, Hunter Teel, Taylor R. Garrick, Srikant Srinivasan, Fengkun Wang, Yangbing Zeng, Sirivatch Shimpalee

Faculty Publications

In this work, discrete element method (DEM) simulations were used to probe changes in electrode porosity, electrode strain, and the resultant pressure changes for composite electrodes comprised of active material and binder particles. Through the results acquired by these simulations, three cases that are representative of two limiting cases for electrode operation, and one case for realistic electrode face pressure during operation were captured and the implications on design and performance are discussed. Predicting changes in the porosity is a unique insight that is difficult if not impossible to capture experimentally but is important for predicting changes in electrochemical performance …

Recent Advances On Ruthenium-Based Electrocatalysts For Lithium-Oxygen Batteries, Yu-Zhe Wang, Zhuo-Liang Jiang, Bo Wen, Yao-Hui Huang, Fu-Jun Li

Journal of Electrochemistry

Rechargeable lithium-oxygen (Li-O₂) batteries have attracted wide attention due to their high energy density. However, the sluggish cathode kinetics results in high overvoltage and poor cycling performance. Ruthenium (Ru)-based electrocatalysts have been demonstrated to be promising cathode catalysts to promote oxygen evolution reaction (OER). It facilitates decomposition of lithium peroxide (Li₂O₂) by adjusting Li₂O₂ morphologies, which is due to the strong interaction between Ru-based catalyst and superoxide anion (O₂^–) intermediate. In this review, the design strategies of Ru-based electrocatalysts are introduced to enhance their OER catalytic kinetics in …

Numerical Analysis Of Explosion Characteristics Of Vent Gas From 18650 Lifepo4 Batteries With Different States Of Charge, Shi-Lin Wang, Xu Gong, Li-Na Liu, Yi-Tong Li, Chen-Yu Zhang, Le-Jun Xu, Xu-Ning Feng, Huai-Bin Wang

Journal of Electrochemistry

The combustion and explosion characteristics of lithium-ion battery vent gas is a key factor in determining the fire hazard of lithium-ion batteries. Investigating the combustion and explosion hazards of lithium-ion batteries vent gas can provide guidance for rescue and protection in explosion accidents in energy storage stations and new energy vehicles, thereby promoting the application and development of lithium-ion batteries. Based on this understanding and combined with previous research on gas production from lithium-ion batteries, this article conducted a study on the combustion and explosion risks of vent gas from thermal runaway of 18650 LFP batteries with different states of …

2024 "Electrochemical Research Paradigms" Summer School Successfully Held, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Upcoming Meeting-The 1St Young Investigator Symposium On Electrosynthesis, Chinese Chemical Society, Chinese Society Of Electrochemistry (Cse)

Journal of Electrochemistry

No abstract provided.

Rate Law For Photoelectrochemical Water Splitting Over Cuo, Bo-Yuan Gao, Wen-Hua Leng

Journal of Electrochemistry

Photocatalytic splitting of water over p-type semiconductors is a promising strategy for production of hydrogen. However, the determination of rate law is rarely reported. To this purpose, copper oxide (CuO) is selected as a model photocathode in this study, and the photogenerated surface charge density, interfacial charge transfer rate constant and their relation to the water reduction rate (in terms of photocurrent) were investigated by a combination of (photo)electrochemical techniques. The results showed that the charge transfer rate constant is exponential-dependent on the surface charge density, and that the photocurrent equals to the product of the charge transfer rate constant …

Winning Results Of The 2Nd Xiamen University Short Video Abstract Contest For Science And Technology Papers, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Winning Works From Journal Of Electrochemistry: The 2Nd Xiamen University Short Video Abstract Contest For Science And Technology Journal Papers, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

2024 World Fuel Cell Conference Held In Ningbo, Zhejiang, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Unveiling The Indoor Performance Of Perovskite/Silicon Tan‑Dem Solar Cells: A Comprehensive Exploration Through Numerically Modelled Energy Band Diagrams, Ziad Khalifa, Sameh O. Abdellatif, Alexander De-Bernardinis, Muath Alkadi, Mostafa Ganoud, Saif Qaid

Chemical Engineering

This paper delves into the indoor performance analysis of Perovskite/Silicon Tandem Solar Cells (PSSTC) through a detailed exploration utilizing numerically modeled energy band diagrams. The primary objective is to uncover the potential of PSSTC for solar energy conversion in indoor settings. Various tandem cell configurations are scrutinized under diverse artificial lighting spectra, with an innovative Li4Ti5O12/ CsPbCl3/MAPbBr3/CH3NH3PbI3/ Si architecture achieving an exceptional maximum power conversion efficiency of 25.25%. This represents a substantial efficiency enhancement of nearly 7% compared to standalone Silicon cells. The study underscores the significance of design optimization in maximizing performance. The energy band diagram analysis reveals a …

Voltammetric Determination Of Hydrogen Peroxide At Decorated Palladium Nanoparticles/Poly 1,5- Diaminonaphthalene Modified Carbon-Paste Electrode, Ziad Khalifa, Mohamed Fathi Abo Oura, Magdi Abdelazzem, Ablah Hathoot

Chemical Engineering

In this work, palladium nanoparticles (PdNPs)/p1,5-DAN/ carbon paste electrode (CPE) and p1,5-DAN/CPE sensors have been developed for determination of hydrogen peroxide. Both sensors showed a highly sensitive and selective electrochemical behaviour, which were derived from a large specific area of poly 1,5 DAN and super excellent electroconductibility of PdNPs. PdNPs/p1,5-DAN/CPE exhibited excellent performance over p1,5-DAN/CPE. Thus, it was used for detecting hydrogen peroxide (H2O2) with linear ranges of 0.1 to 250 μM and 0.2 to 300 μM as well as detection limits (S/N= 3) of 1.0 and 5.0 nM for square wave voltammetry (SWV) and cyclic voltammetry (C.V) techniques, respectively. …

Optogenetic Control Of Bacterial Dormancy, Yousr Dhaouadi Khattab

Dissertations - ALL

The presence of persister cells makes it difficult to eradicate chronic bacterial infections as these dormant subpopulations arise with exposure to stressors and are capable of surviving antimicrobials that target active cells. Persisters can also revert back to normal growing cells when stressors are removed thus reestablishing the infection. It is therefore important to understand the underlying mechanisms of persister formation, as well as wake-up, and target these systems in order to treat chronic bacterial infections. The formation of persisters, however, remains elusive as there is not yet a clear relationship between the various stages of dormancy. Persister cells can …

Chemistry And Processing Of Carbon/Carbon Composites From Furan-Based Polybenzoxazine Resins, Michael Chauby

Theses and Dissertations

Carbon/carbon (C/C) composites are valuable for applications requiring structural integrity at high temperatures. However, their widespread use is limited by high manufacturing costs. Monofunctional furan-based benzoxazine resins were identified as promising candidates for enhancing fabrication efficiency due to their low viscosity, high char yield, and high carbon density. A benzoxazine monomer synthesized from furfurylamine, formaldehyde, and benzyl alcohol (Bz-FA-H) exhibits a crosslinking reaction between the furan group and the hydroxymethyl para substituent on the phenol, not found with other monomers. An investigation using blends of monomers containing Bz-FA-H at various concentrations showed that increasing crosslink density resulted in increased bulk …

Quantifying The Impact Of Microstructure Variation On Charging Capability In Lithium-Ion Batteries, Hunter Teel, Taylor R. Garrick, Mitchell A. Sepe, Joseph S. Lopata, Srikant Srinivasan, Fengkun Wang, Yangbing Zeng, Sirivatch Shimpalee

Faculty Publications

Through the use of electrochemical simulations, variation in the local onset of lithium plating can be predicted and used to set charging guidelines to reduce the risk of lithium plating. The pseudo-two-dimensional (P2D) model is typically used for capturing this behavior; however, it only provides a global lithium plating onset estimate and does not consider the local variation. With material properties translated to an average continuum value, the P2D model can simulate rapid charge and capture global onset of lithium plating. However, this model lacks the ability to resolve localized behaviors across individual components due to local non-uniformities. Our three-dimensional …

Consistent Intraocular Pressure Reduction By Solid Drug Nanoparticles In Fixed Combinations For Glaucoma Therapy, Da Huang, Pedro Norat, Lin Qi, Anna Chernatynskaya, James D. Cole, Vimalin Jeyalatha Mani, Lei Xu, Xiaorong Liu, Hu Yang

Chemical and Biochemical Engineering Faculty Research & Creative Works

Efficient topical drug delivery remains a significant challenge in glaucoma management. Although nanoparticle formulations offer considerable promise, their complex preparation processes, co-delivery issues, and batch consistency have hindered their potential. A scalable fabrication strategy is developed here for preparing solid drug nanoparticles (SDNs) with enhanced drug delivery efficiency. Utilizing hydrophobic antiglaucoma drugs brimonidine (BM) and betaxolol (BX), uniform fixed combination BM/BX SDNs are fabricated through a continuous process, improving batch-to-batch consistency for combined glaucoma treatment. With trehalose being used as a lyoprotectant, BM/BX SDNs can be stored as dry powder and easily reconstituted in phosphate buffered saline. Importantly, reconstituted BM/BX …

Production And Characterization Of Bio-Oil From Camelthorn Plant Using Slow Pyrolysis, Attia Attia Prof., Dina Aboelela Dr., Habibatallah Saleh Eng., Yasser Elhenawy Prof., Thokozani Majozi Prof., Mohamed Bassyouni Prof.

Biochemical Engineering

In this study, slow pyrolysis of the camelthorn plant process was conducted to produce bio-oil, biochar, and gas. The pyrolysis process was conducted between 400 and 550 °C under pressure 10 bar using a fixed bed reactor. The pyrolysis products were bio-oil, biogas, and biochar. These products were characterized using Fourier-transform infrared (FT-IR) model, gas analyzer, chromatographic analysis using GC–MS, and thermogravimetric analysis (TGA). The GC–MS results demonstrated composition of bio-oil, detecting several organic substances including levoglucosan, furan, acetic acid, phenol, and long-chain hydrocarbon. To further understand the chemical composition of bio-oil, FT-IR spectroscopy was conducted to determine functional groups. …

Analysis Of The Factors Affecting The Oil Recovery From Oilseeds In A Multistage Crosscurrent Leaching Process, Samuel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

The analysis of the total oil recovery from oilseeds in a multi-stage crosscurrent leaching process is presented. The model created using mass balance equations for three stages was used to analyze the factors affecting total oil recovery, To. The key performance factors (raw meal feed flow rate, solvent feed flow rate in each stage, solvent distribution factor for each stage, percent oil in the raw meal (Poil), solids to solution ratio in the underflow (N), solvent to solids ratio (SSR), solvent to oil ratio (SOR) and wash ratio (WR) were varied while assessing To. While SSRi and SORi ranged from …

Development And Testing Of Small-Scale Flash Dryer For Maize Bran, Eden Ngowi

Tanzania Journal of Engineering and Technology (TJET)

Sun drying is the most common technique used to dry various food products due to its economic convenience. However, it is not effective owing to its unreliable nature leading to microbial deterioration and aflatoxin contamination of food. In Tanzania, about 1.3 million tonnes of maize bran are at risk of deterioration annually due to improper drying. The aim of this study was to design, fabricate and test an efficient small-scale flash dryer for maize bran. Using principles of material and energy balance, a small-scale flash dryer with a throughput of 500 kg of dry product per hour was designed resulting …

Investigation Of Heavy Metal Composition And Associated Health Risks From Selected Groundwater Wells In Temeke, Dar-Es-Salaam, Justin M. Jeremiah

Tanzania Journal of Engineering and Technology (TJET)

Water quality continues to be the challenge to residents in Dar es Salaam due to various anthropogenic activities in the city. This study was conducted to assess groundwater quality by determining concentrations of heavy metals. Both probability and Nonprobability sampling techniques were used to collect samples from 40 groundwater wells in 24 wards of Temeke municipal and analysed using Microwave Plasma Atomic Emission Spectrometer (Agilent 4210 MP-AES) at the Geochemistry Laboratory of the University of Dar es Salaam. Results indicated varying heavy metal concentrations ranging from 0.71 ± 0.08 to 6.64 ± 0.21 mg/l for As, 0.02 ± 0.01 to …

A Coarse-Grained Molecular Dynamics Study Of Gas Hydrate Formation And Dissociation, Meisam Adibifard

LSU Doctoral Dissertations

The study of gas hydrates has increased significantly over the last two decades because of their potential application in energy storage, production and transportation, water desalination, refrigeration, gas separation, etc. There is a significant interest in commercially developing natural gas hydrates because the energy content of methane hydrate reservoirs (MHRs) is at least twice that of all conventional fossil fuels combined. Additionally, due to the higher storage capacity of hydrates, it is proposed to sequester CO₂ in the form of CO₂ hydrate, thereby reducing the amount of greenhouse gases. Hence, hydrates offer a dual solution to two of …

Beyond Measures Of Speed & Accuracy: Evaluating Visualization Perception, Reasoning & Decision-Making, Melanie Bancilhon

McKelvey School of Engineering Graduate Student Theses & Dissertations

Visualizations have long been used to support decision-making across various fields. By transforming complex data into graphical representations, such as charts, graphs, and maps, visualizations are generally reputed to make information more accessible and comprehensible for all. While prior work demonstrates that visualizations can improve speed and accuracy across comprehension and analytical tasks, there lacks research on how they can benefit decision-making. Decision-making is a complex task which involves risk comprehension and rational thinking but also various heuristics and external factors. While research has shown that individual traits and situational factors can impact performance with visualizations, they have not been …

Guiding 3d Chiral Self-Assembly At Nano/Micro Length Scales Via 3d Printing, Mohsen Esmaeili

Theses and Dissertations

This thesis delves into the intricate realm of 3D printing bio-inspired materials with tailored nano/microscale architectures. The first chapter investigates the flow-induced alignment of cellulose nanocrystals (CNC) during 3D printing, employing a microfluidic strategy integrated with polarized optical microscopy (POM). Birefringence measurements under varying conditions reveal the influence of initial CNC suspension structures on flow-induced patterns, particularly in the chiral nematic phase. Hydrodynamic simulations complement experimental findings, elucidating the impact on CNC particle alignment, providing insights for designing 3D printed architectures with internal chirality for advanced applications.

The second chapter explores the 3D printing of complex geometries inspired by Bouligand …

Development Of Dip-Coated Carbon Fibers For Structural Power Composites And Optimization Of Bus Plates For Passively Propagation Resistant Batteries, David Petrushenko

Theses and Dissertations

Increasing demand for lithium-ion batteries in electric vehicles, portable electronics, and electric aircraft is a driving force for the expansion in new battery architectures to achieve higher gravimetric and volumetric efficiencies. In practice, maximizing energy density can be achieved by introducing state-of-the-art materials to increase the capacity of cells or by reducing the system's mass by incorporating lightweight structural materials. An alternative approach is to develop systems capable of performing multiple functions simultaneously that combine mono-functions of the battery and vehicular structure in a multifunctional component capable of storing electrical energy and providing structural support.

The initial focus of this …

Mathematical Modeling And Reconstruction Of Porous Media To Understand Transport Phenomena For Electrochemical System Applications, Mitchell Sepe

Theses and Dissertations

Alternative power generation has grown significantly in the space of energy production over the last ten years. Development of new technologies to produce energy is vital to the growing need for electricity. Batteries, solar panels, wind turbines, and countless other renewable energy options have been deemed necessary to create an overall greener future. Fuels cells when combined with electrolyzer show a promising system for stationary power generation. Both technologies are comprised of multiple parts in contact that must work together simultaneously to create an ideal environment for catalytic reactions to take place. A crucial component to a properly functioning cell …

A Study Of Direct Sensitivity Method Solving Optimal Control Problems With Single And Multiple Time Grids With An Application In An Experimental Hybrid System, Hainan Wang

Theses and Dissertations

Computational methods for optimal control are important for dealing with bottlenecks in industries. By implementing optimal operation strategies obtained from the computational methods into dynamic systems, objectives such as saving energy, reducing cost, exploiting potential, and improving efficiency can be achieved. Computational methods for optimal control have been used in a broad range of disciplines, including aeronautics and astronautics, oil and chemical engineering, power systems, clean energy, biomedical engineering, economics, and management. Due to the great application value of optimal control, its computational methods have drawn worldwide attention. Direct methods are most effective in computational methods for optimal control. Direct …

On The Use Of Cfd Modeling And Analytic Methods To Describe Pressure Drop In Highly Dense Structured Adsorbents In Gas Separation Processes And Fundamentals Of Adsorption, Ryan Timothy Sanders

Theses and Dissertations

The scope of this work can be divided into two main thrusts on topics found within adsorption. The first, and primary, topic is the use of CFD and analytical modeling to describe the flow of gas through a parallel, structured adsorbent channel which is described in Chapters 1 and 2. Chapter 1 establishes a non-experimental methodology based on using a 3D Navier-Stokes (NS) computational fluid dynamics (CFD) model in lieu of experiments, for developing 1D axial pressure drop correlations for structured adsorbents with parallel channels. Chapter 2 utilizes the methodology established in Chapter 1 in order to develop a new …

A Click Chemistry Amplified Nanopore Assay For High Performance Testing Of Protein Biomarkers In Diseases, Xiaoqin Wang

Theses and Dissertations

Nanopore detection technology enables nanometer-scale single-molecule detection, yielding valuable insights into analyte molecules' properties such as size, shape, charge, and concentration. Due to its label-free nature, high sensitivity, and real-time capabilities, it finds widespread application in genomics, proteomics, drug discovery, and environmental monitoring. Click chemistry, encompassing the attachment of a probe or substrate to a biomolecule, termed bioconjugation, features the copper-catalyzed azide-alkyne cycloaddition as a quintessential reaction, forming a 5-membered heteroatom ring. This study harnesses this reaction to craft single-strand DNA probes for nanopore testing, leveraging copper's catalytic properties for signal amplification. Host-guest reaction, a noncovalent bond between molecules, specifically …

Engineering Electronic Properties Of Random Alloys For Catalytic Applications, Andrew N. Okafor

LSU Doctoral Dissertations

Engineering catalytic materials is a key endeavor in the catalysis science to improve the catalytic activity of existing catalysts for specific applications and reduce the dependence on rare metals and minerals. While alloying, or mixing of metals, has been extensively studied, the focus has conventionally been placed on intermetallic phases or nanostructures such as core-shell particles, which are conceptually described by simple lattice models. This research focuses on understanding the catalytic properties of structurally ordered but compositionally disordered (or random) alloys, which have remained under-explored due to complexity at the atomic scale. Existing research focuses on synthesizing multicomponent alloys and …

Coal Wettability: A Holistic Overview Of The Data Sets, Influencing Factors, And Knowledge Gaps, Muhammad Arif, Faisal Ur Rahman Awan, Haiyang Zhang, Mirhasan Hosseini

Research outputs 2022 to 2026

Coal seams are naturally occurring geological media offering tremendous potential for gas storage. The wetting characteristics of coals at typical geological formations underpin a diverse array of processes spanning coal resource recovery, combustion, enhanced coal beneficiation, enhanced methane recovery, and CO2 storage for sustainable energy transition. An accurate characterization of coal wettability is thus crucial and remains an active area of research. The intrinsic heterogeneity of coal surfaces and the presence of multicomponent systems add layers of intricacy to wetting behavior. In particular, coal wettability characterization is challenging because it is a complex and multifaceted function of a range of …