Chemical Engineering Commons^™

The Effect Of Irradiation Of Fe And Ar Ion On The Surface Morphology Of Diamond Thin Film Related To The Magnetoresistance Property, Salim Mustofa, Setyo Purwanto, Kenji Mishima

Makara Journal of Technology

The irradiation of Fe and Ar ion was applied on the surface of diamond/Si thin film to know its effect on the morphology of thin film.The magnetoresistance property was also studied. Ion irradiation treatment using Fe ion followed by argon ion at the energy of 70keV and a dose of 1 x 1015 ion/cm2 have been conducted on the surface of two types of thin film, diamond/Si (111) and diamond/Si (100). Both thin films were made by using a CVD method, and the thickness of the thin film is 1000-nm. From simulations using the software called Stopping and Range of …

Use Of Green Mussel Shell As A Desulfurizer In The Blending Of Low Rank Coal-Biomass Briquette Combustion, Mahidin Mahidin, Asri Gani, M. Reza Hani, Muhammad Syukur, Hamdani Hamdani, Khairil Khairil, Samsul Rizal, Abdul Hadi, T.M.I. Mahlia

Makara Journal of Technology

Calcium oxide-based material is available abundantly and naturally. A potential resource of that material comes from marine mollusk shell such as clams, scallops, mussels, oysters, winkles and nerites. The CaO-based material has exhibited a good performance as the desulfurizer or adsorbent in coal combustion in order to reduce SO2 emission. In this study, pulverized green mussel shell, without calcination, was utilized as the desulfurizer in the briquette produced from a mixture of low rank coal and palm kernel shell (PKS), also known as bio-briquette. The ratio of coal to PKS in the briquette was 90:10 (wt/wt). The influence of green …

Apparent Porosity And Compressive Strength Of Heat-Treated Clay/Iron Sand/Rice Husk Ash Composites Over A Range Of Sintering Temperatures, M. Nizar Machmud, Zulkarnain Jalil, Mochammad Afifuddin

Makara Journal of Technology

Novel composites of clay/iron sand/rice husk ash (RHA) have been developed. Electric furnace was used to perform heat treatment on the composites to study the effect of sintering temperature on their apparent porosity and compressive strength. Two types of RHA with different bulk density were prepared to gain an understanding of the influence of apparent porosity on compressive strength of the heat-treated composites over a range of sintering temperatures. Heattreated composites, made of clay/iron sand and clay/RHA, were also prepared as a referenced material. X-ray diffraction (XRD) analysis was further performed to comprehensively discuss the role of iron sand on …

Delay-Independent Stability Analysis Of Linear Time-Delay Systems Based On Frequency, Xianwei Li, Huijun Gao, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies strong delay-independent stability of linear time-invariant systems. It is known that delay-independent stability of time-delay systems is equivalent to some frequency-dependent linear matrix inequalities. To reduce or eliminate conservatism of stability criteria, the frequency domain is discretized into several sub-intervals, and piecewise constant Lyapunov matrices are employed to analyze the frequency-dependent stability condition. Applying the generalized Kalman–Yakubovich–Popov lemma, new necessary and sufficient criteria are then obtained for strong delay-independent stability of systems with a single delay. The effectiveness of the proposed method is illustrated by a numerical example.

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Haul Truck Tires Recycling, Jessica N. Lizarazu

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers. These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months. Statistics regarding discarded OTR tires are not provided by the …

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Thermal Properties, Crystallinity, And Oxygen Permeability Of Na-Montmorillonite Reinforced Plasticized Poly(Lactic Acid) Film, Kurniawan Yuniarto, Yohanes Aris Purwanto, Setyo Purwanto, Bruce A. Welt, Hadi Karia Purwadaria, Titi Candra Sunarti

Makara Journal of Technology

Introducing unmodified organically clay/Na-montmorillonite (Na-MMT) was applied into plasticized poly(lactic acid) PLA to produce film composites by direct casting. Film composite structure, the crystallinity degree and form, and thermal properties were carried out using X-ray diffraction and differential scanning calorimetry. The effect of Na- MMT to the tortuous path and the crystallinity degree in the plasticized film composites were calculated in oxygen barrier properties. Chromatogram film composites resulted in an intercalated structure that showed peak diffraction angle shift at about 0.2o. Then, a peak diffraction pattern was indicated in α-form crystal structure. Plasticized PLA has a crystallinity degree at 34%, …

Residual Strength Analysisof Asymmetrically Damaged Ship Hull Girderusing Beam Finite Element Method, Muhammad Zubair Muis Alie

Makara Journal of Technology

The objective of the present study is to analyze the residual strength of asymmetrically damaged ship hull girder under longitudinal bending. Beam Finite Element Method is used for the assessment of the residual strength of two single hull bulk carriers (Ship B1 and Ship B4) and a three-cargo-hold model of a single-side Panamax Bulk Carrier in hogging and sagging conditions. The Smith’s method is adopted and implemented into Beam Finite Element Method. An efficient solution procedure is applied; i.e. by assuming the cross section remains plane, the vertical bending moment is applied to the cross section and three-cargo-hold model. As …

Discrete Power Control In Heterogenous Networks, Yuanyuan Wang, Wibowo Hardjawana, Branka Vucetic

Makara Journal of Technology

In heterogeneous networks (HetNets) where femtocell base stations (FBSs) are deployed within the radio coverage of macrocell base stations (MBSs) to increase network capacity, co-channel interference limits overall system performance with universal frequency reuse. This paper investigates new distributed downlink discrete power control scheme for FBSs in HetNets with FBSs cooperation. The objective of the proposed power control scheme is to maximize the number of simultaneous FBSs transmissions in a single transmission wireless channel where each FBS is allowed to transmit only if the signal-to-interference-noise ratio (SINR) requirements for both FBSs and MBS users are satisfied. We apply a stochastic …

Multi-Project Scheduling Cost Optimization In A Machine Manufacturer Engineer-To-Order, Farizal Farizal, Amar Rachman, Tifani Tandean, Sumarsono Sudarto, Katsuhiko Takahashi

Makara Journal of Technology

This paper discusses the utilization of mixed integer linear programming (MILP) model to optimize cost for multiproject scheduling in a machine maker company. The objective is to minimize total project’s penalty cost and labor cost. The model formulated shows how to achieve the objective i.e. whether to use outsourcing or overtime to finish all projects. The model of multi-project scheduling was solved by Branch & Bound algorithm coded in Lingo 14.0 software. The case study shows that if a company wants to minimize lateness, it should use overtime instead of outsourcing, which minimize total lateness of projects by 144 days …

Analysis Of Arm Movement Prediction By Using The Electroencephalography Signal, Reza Darmakusuma, Ary Setijadi Prihatmanto, Adi Indrayanto, Tati Latifah Mengko, Lidwina Ayu Andarini, Achmad Furqon Idrus

Makara Journal of Technology

Various technological approaches have been developed in order to help those people who are unfortunate enough to be afflicted with different types of paralysis which limit them in performing their daily life activities independently. One of the proposed technologies is the Brain-Computer Interface (BCI). The BCI system uses electroencephalography (EEG) which is generated by the subject’s mental activity as input, and converts it into commands. Some previous experiments have shown the capability of the BCI system to predict the movement intention before the actual movement is onset. Thus research has predicted the movement by discriminating between data in the “rest” …

Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li

Makara Journal of Technology

Austenitic steel is one type of stainless steel which is widely used in the industry. Many studies on austenitic stainless steel have been performed to determine the physical properties using various types of equipment and methods. In this study, the neutron diffraction method is used to characterize the materials which have been made from minerals extracted from the mines in Indonesia. The materials consist of a granular ferro-scrap, nickel, ferro-chrome, ferro-manganese, and ferro-silicon added with a little titanium. Characterization of the materials was carried out in three processes, namely: machining, annealing, and rolling. Experimental results obtained from the machining process …

Maneuverability Of Ships With Small Draught In Steady Wind, Daeng Paroka, Andi Haris Muhammad, Syamsul Asri

Makara Journal of Technology

Wind force and moment may force a ship to drastically decrease its speed and use a large drift angle as well as a large rudder angle in order to maintain its course. Ships with a small draught might have more risk in maneuvering to its point of view compared with a ship with a larger draught. This paper discusses maneuverability of a ship with a small draught in steady wind. The effect of wind on ship speed, drift angle, and rudder angle are investigated in a steady state condition. Five different ratios of wind velocity to ship speed from 1.0 …

A Comparison Of American, Norwegian, And Russian Standards In Calculating The Wall Thickness Of Submarine Gas Pipeline, Cindy Dianita, Tatyana Vladimirovna Dmitrieva

Makara Journal of Technology

One of the key issues in the pipeline design is wall thickness calculation. This paper highlights a comparison of wall thickness calculation methods of submarine gas pipeline based on Norwegian Standard (DNV-OS-F101), Indonesian Standard SNI 3474 which refers to American Standard (ASME B31.8), and Russian Standard (VN39-1.9-005-98). A calculation of wall thickness for a submarine gas pipeline in Indonesia (pressure 12 MPa, external diameter 668 mm) gives the results of 18.2 mm (VN39-1.9-005-98), 16 mm (ASME B31.8), and 13.5 mm (DNV-OS-F101).The design formula of hoop stress due to internal pressure is interpreted in different ways for every standard. Only Norwegian …

Modified Yttrium Hydroxide/Mc Nylon Nanocomposites And Scaling Effects In Multilayer Polyethylene Films, Jia Chen

USF Tampa Graduate Theses and Dissertations

In this thesis, monomer casting (MC) nylon was synthesized. MC nylon could replace nonferrous metals in certain applications, including gears, wheels, and other moving parts. However, compared with metals, MC nylon products have poor strength and stiffness, and crack easily, especially at low temperatures. In addition, the dimensional stability of MC nylon is poor, especially in the large casting nylon products, causing significant internal stresses due to shrinkage. Thus, MC nylon cracks easily when cast and molded. The yttrium hydroxide particles were modified by stearic acid and dispersed in the caprolactam. The polymerization time was short due to fast anionic …

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

Hybrid Metal Oxide Cycle Water Splitting, Richard B. Diver Jr, Robert D. Palumbo, Nathan P. Siegel, James E. Miller

Other Faculty Research and Publications

Hybrid thermochemical water splitting cycles are provided in which thermally reduced metal oxides particles are used to displace some but not all of the electrical requirements in a water splitting electrolytic cell. In these hybrid cycles, the thermal reduction temperature is significantly reduced compared to two-step metal-oxide thermochemical cycles in which only thermal energy is required to produce hydrogen from water. Also, unlike the conventional higher temperature cycles where the reduction step must be carried out under reduced oxygen pressure, the reduction step in the proposed hybrid cycles can be carried out in air, allowing for thermal input by a …

Modeling And Evaluation Of Moisture Diffusion In Polymer Composite Materials, Zhen Huo

Doctoral Dissertations

"Fiber-reinforced polymer composites have extensive applications due to their high specific strength, improved product performance, low maintenance and design flexibility. However, moisture absorbed by polymer composites during the service life plays a detrimental role in both the integrity and durability of composite structure. It is essential to understand the moisture diffusion behavior and induced damage in polymer matrix composites under varying hygrothermal conditions. In Part I, the moisture diffusion characteristics in hybrid composites using moisture concentration-dependent diffusion method have been investigated. Also, a multi-stage diffusion model was proposed to explain the deviation of moisture diffusion behavior for sandwich composites from …

Diffusion-Mediated Deposition Of Proteins, Ruiqian Zhan

Theses and Dissertations--Mechanical and Aerospace Engineering

Gradients of proteins play a prominent role in many biological processes, from development of multicellular organisms to chemical signaling in the immune system. Deposition of surface gradients is a way to permanently modifying a surface’s properties, resulting in the creation of novel materials which have widespread applications in biologically relevant fields, such as directed cell growth, production of biocompatible implantable materials, and creation of functional biosensors. These types of surfaces can also be used as an ex vivo tool to help understand many biological processes by mimicking the environment in gradient-related phenomena in a controllable way. However, despite the large …

Numerical Analysis Of Flexural Slip During Viscoelastic Buckle Folding, Davi Rodrigues Damasceno

Masters Theses

"Flexural slip is considered to be an important folding mechanism contributing in the development of different folds such as chevron, and kink-band buckle folds. Various filed studies have provided a general conceptual and qualitative understanding of flexural slip. However, quantitative evidence of the importance of the flexural slip mechanism during fold evolution is sparse, as the actual amount of surface parallel displacement, and timing, is difficult to measure accurately, due to the lack of suitable strain markers.

In this study 2D finite element analysis is used to overcome these disadvantages and to simulate flexural slip during viscoelastic buckle folding. Variations …

Design And Commissioning Of A Community Scale Solar Powered Membrane-Based Water Purification System In Haiti, Shavin Pinto, Yung Wong, Kyle Fennesy, Yan Tang, Marc Compere

Publications

This paper presents the design and commissioning of a solar powered water purification system at the Ryan Epps Home for Children (REHC) in Michaud, Haiti. This system supplies clean drinking water to the 200 children who live and go to school at REHC and also to the community in the form of a micro-business. This micro-business is the mechanism for income generation for sustainable system operation. The purifier uses a three stage filtration system with a disc-type sediment filter, a 0.1 micron ultrafiltration membrane, and an ultraviolet light for disinfection. The backwash cycle extends the life of the ultrafiltration membrane …

Combustion Of Novel Thermite Mixtures For Iodine Generation, Sergio Emanuel Guerrero

Open Access Theses & Dissertations

Halogen-containing reactive materials could be used for mitigating the spread of hazardous, active biological microorganisms aerosolized as a result of explosion. The present work exhibits experimental results on the combustion of mechanically alloyed aluminum-iodine (Al-I2) powder mixed with Fe2O3, CuO, MoO3, Bi2O3, and I2O5. Wet mixing was used to prepare the samples, which were then compacted into pellets and ignited with a CO2 laser. A chamber was designed and built to accommodate for combustion and collection of products, and the available laser ignition setup was modified to enable combustion experiments with rapidly burning gas-generating mixtures. High-speed video recording was used …

Improving Renewable Energy Transition Acceptance: A Simulation Gaming Approach On A Multi Actor Setting In The Netherlands, Aziiz Sutrisno, Jac A. M. Vennix, Noor Syaifudin

Makara Journal of Technology

The Netherlands have tried very hard to increase their renewable energy sources (RES) shares to fulfill the European Union target in 2050. However, RES performance did not show the expected result as the performance declined in 2009 producing even wider gap compare to the target. The Dutch government’s tried to incorporate all interested stakeholders by forming the Dutch energy transition task force. Nevertheless, the task force’s result is also not showing a desirable trend. Key reasons behind the Dutch low RES performance are the lack of shared understanding and positive attitude toward RES development among interested actors. This research uses …

Dual-Band Singly-Fed Proximity-Coupled Tip-Truncated Triangular Patch Array For Land Vehicle Mobile System, Basari Basari, Josaphat Tetuko Sri Sumantyo

Makara Journal of Technology

This paper proposes a dual-band left-handed circularly polarized triangular-patch array that is developed for land vehicle mobile system aimed at mobile satellite communications. The array consists of six tip-truncated triangular patches, which the first three patches are used for reception and the second three patches are used for transmission purpose. Each of three-patches has a beam pattern that can be switched in three different 120°-coverage beam in azimuth-cut plane at a minimum targeted gain at a desired elevation angle. The targeted minimum gain of the array is 5 dBic, in order for data communications with a large geostationary satellite can …

Improvement Of Quality Of Carica Papaya L. With Clove Oil As Preservative In Edible Coating Technology, Eny Kusrini, Anwar Usman, Chrispine Deksita Wisakanti, Rita Arbianti, Dedy Alharis Nasution

Makara Journal of Technology

We have studied utilization of essential clove oil, extracted from clove buds by hydrodistillation, as preservative in edible packaging technology. Preservative of essential clove oil was applied on chopped papaya fruits by using two methods, namely spray and brush. The effects of concentration of clove oil from 0.05 to 0.20% on the preservation of papaya fruits (Carica papaya L.) at room temperature (25 °C) were also evaluated. Physicochemical and in vitro microbiological activities on the papaya fruits that were stored at 25 oC and 85-90% relative humidity were investigated in details. The results indicate that the clove oil at concentration …

Calibration Of Numerical Model For Shoreline Change Prediction Using Satellite Imagery Data, Sigit Sutikno, Keisuke Murakami, Dwi Puspo Handoyo, Manyuk Fauzi

Makara Journal of Technology

This paper presents a method for calibration of numerical model for shoreline change prediction using satellite imagery data in muddy beach. Tanjung Motong beach, a muddy beach that is suffered high abrasion in Rangsang Island, Riau province, Indonesia was picked as study area. The primary numerical modeling tool used in this research was GENESIS (GENEralized Model for Simulating Shoreline change), which has been successfully applied in many case studies of shoreline change phenomena on a sandy beach.The model was calibrated using two extracted coastlines satellite imagery data, such as Landsat-5 TM and Landsat-8 OLI/TIRS. The extracted coastline data were analyzed …

Independency Of Elasticity On Residual Stress Of Room Temperature Rolled Stainless Steel 304 Plates For Structure Materials, Parikin Parikin, David Allen

Makara Journal of Technology

Mechanical strengths of materials are widely expected in general constructions of any building. These properties depend on its formation (cold/hot forming) during fabrication. This research was carried out on cold-rolled stainless steel (SS) 304 plates, which were deformed to 0, 34, 84, and 152% reduction in thickness. The tests were conducted using Vickers method. Ultra micro indentation system (UMIS) 2000 was used to determine the mechanical properties of the material, i.e.: hardness, modulus elasticity, and residual stresses. The microstructures showed lengthening outcropping due to stress corrosion cracking for all specimens. It was found that the tensile residual stress in a …