Chemical Engineering Commons^™

Oxidative Efficiency Of Ozonation Coupled With Electrolysis For Treatment Of Acid Wastewater, Ze-You Hu, Feng-Yun Xiang, Ji-Qiang Mao, Ya-Lei Ding, Shao-Ping Tong

Journal of Electrochemistry

Establishment of an ozone-based advanced oxidation process (AOPs-O₃) for effective treatment of acid wastewater is an important and difficult task. The process of ozonation coupled with electrolysis (electrolysis-ozonation, E-O₃) has been reported to effectively degrade pollutants in neutral solution. We studied the efficiency of E-O₃ for degradation of acetic acid (HAc, an ozone inert chemical) in acid solution and found that E-O₃ had high oxidative efficiency at pH less than 3. For example, 52.2% of 100 mg·L^-1 HAc could be removed by E-O₃ in 120 min at pH 1.0, but only 2.2% …

Synthesis Of Lithium-Rich Manganese-Based Layered Cathode Materials And Study On Its Structural Evolution Of First Cycle Overcharge, Chen-Xu Luo, Chen-Guang Shi, Zhi-Yuan Yu, Ling Huang, Shi-Gang Sun

Journal of Electrochemistry

Lithium-rich manganese-based cathode materials have become one of promising cathode materials due to their low cost and large discharge specific capacity exceeding 250 mAh·g^-1. However, their problems such as low coulombic efficiency of first cycle and apparent voltage decay influence commercialization process. The high charging voltage will cause instability of structure and increase the hidden danger of the battery. Therefore, structural evolution of first cycle at higher voltage needs to be further studied. In this work, the precursor was synthesized by the co-precipitation method, and the lithium-rich manganese-based layered cathode materials were prepared by lithium-mixed and high-temperature sintering, …

Design And Analysis Of Marangoni-Driven Robotic Surfers, Mitchel L. Timm

Dissertations, Master's Theses and Master's Reports

We designed and experimentally studied the dynamics of two robotic systems that surf along the water-air interface. The robots were self-propelled by means of creating and maintaining a surface tension gradient resulting from an asymmetric release of isopropyl alcohol (IPA). The imbalance in the distribution of surface tension surrounding the robots generates a propulsive force commonly referred to as Marangoni propulsion. First, we considered a single surfer, which was custom-made with novel control mechanisms that allow for both forward motion and steering to be remotely adjusted solely through the manipulation of local surface stresses. We analyzed the performance of this …

Recycled Printer Filament, Charlotte Hyland, Troy D. Molinar

Williams Honors College, Honors Research Projects

The purpose of this research is to examine the effects of recycling PLA filament for 3D printing on its material properties. After examining these effects, PLA and carbon fiber additives were mixed with recycled PLA pellets in different ratios to attempt to regain material properties lost in the recycling process. To complete these findings, an experiment was design and executed.

The research found that tensile strength during multiple iterations of recycling remained mostly unaffected, however, the strain degraded exponentially. In the PLA additive study, high ratios of PLA additive were able to increase the strength and strain properties of the …

Effect Of Glycol Based Coolant Pollution On Pem Fuel Cells Stack And Recovery Measures, Cong-Yi Zhu, Xiao-Hui Li, Quan-Quan Gan

Journal of Electrochemistry

As the heat conduction medium of fuel cell cooling system, coolant is very important for the thermal management of fuel cell stack. In practical application, coolant leakage into the stack often occurs. Due to the randomness of fault location of components, the location of coolant leakage is uncertain, which may occur on the cathode side or anode side of some or all single cells. The main effects of coolant pollution on fuel cell stack are as follows: the output of open circuit voltage decreases sharply, the consistency of single cells voltage decreases and so on, which seriously affects the normal …

Copper Nanoparticles In-Situ Anchored On Nitrogen-Doped Carbon For High-Efficiency Oxygen Reduction Reaction Electrocatalyst, Hui-Fang Yuan, Yue Zhang, Xing-Wu Zhai, Li-Bing Hu, Gui-Xian Ge, Gang Wang, Feng Yu, Bin Dai

Journal of Electrochemistry

Compared with noble metal platinum (Pt)-based catalysts, inexpensive non-noble metal electrocatalysts have attracted extensive attention for oxygen reduction reaction (ORR). Herein, chitosan as a kind of biomass resource rich in nitrogen and carbon was used to prepare nitrogen-doped carbon (N-C) and N-C in-situ anchored by copper nanoparticles (Cu/N-C). The as-obtained N-C and Cu/N-C nanoparticles were successfully used as non-noble eletrocatalysts tested for ORR. Compared with the N-C, the Cu/N-C showed the high surface area of 607.3 m ²·g^-1 with the mean pore size of 2.5 nm and the pore volume of 0.40 cm³·g^{-1 …}

Structure Analysis Of Pemfc Cathode Catalyst Layer, Rui-Qing Wang, Sheng Sui

Journal of Electrochemistry

The sluggish oxygen reduction reaction (ORR) on the cathode of the proton exchange membrane fuel cell (PEMFC) has always been one of the key factors limiting its commercialization. The optimization of the cathode catalytic layer structure plays an important role in improving fuel cell performance and reducing production costs. In this paper, two different catalysts (platinum nanoparticles (Pt-NPs) and platinum nanowires (Pt-NWs)) were prepared by using catalyst coated substrate (CCS) method. By constructing a double-layer catalytic layer structure, we analyzed the effect of different catalytic layer structures by performing a single cell test. The results showed that the dense platinum …

Formation And Morphological Evolution Of Nanoporous Anodized Iron Oxide Films, Jin-Wei Cao, Nan Gao, Zhao-Qing Gao, Chen Wang, Sheng-Yan Shang, Yun-Peng Wang, Hai-Tao Ma

Journal of Electrochemistry

The preparation of iron oxide films with nanoporous structure by anodization has attracted much attention for its potential applications. However, the formation mechanism of porous structure during anodization is still unclear. In this paper, the composition of anodic current during the formation of nanoporous anodized iron oxide film was analyzed in combination with the current density-potential response (I-V curve) and the derivation of Faraday’s law. The results showed that the anodic current consisted of an ionic current (leading to the migration of ions to form oxide) and an electronic current (leading to the oxygen evolution), and the …

Effect Of Alkyl Chain Length Of Symmetrical Quaternary Ammonium Hydroxide On Oxalic Acid Electroreduction Reaction, Bo Huang, Xin-Sheng Zhang, Dong-Fang Niu, Shuo-Zhen Hu

Journal of Electrochemistry

Glyoxylic acid with the dual characteristics of acid and aldehyde is an important chemical raw material and organic synthesis intermediate, which is extensively used in the perfumery, pharmaceutical and fine chemical industries. A family of symmetric quaternary ammonium hydroxides (QAHs) with different alkyl chain lengths was used as the additives in generating glyoxylic acid from oxalic acid electroreduction reaction (OAER). The effects of alkyl chain length on OAER and the corresponding side reaction, i.e., hydrogen evolution reaction (HER), were investigated. Linear sweep voltammetric (LSV) results showed that the adsorption of the additives suppressed more on the HER than that on …

Performance And Mechanism Of PtXCuY/C Electrocatalyst For Methanol Oxidation, Jia Tang, Xiao-Ming Zhang, Shan-Sheng Yu, Su-Li Wang, Gong-Quan Sun

Journal of Electrochemistry

Direct methanol fuel cell (DMFC), which directly converts the chemical energy of methanol fuel into electrical energy, has the advantages of high energy conversion efficiency, environmental friendliness, and abundance of fuel sources. DMFC is considered as the promising substitutes in the field of portable devices, military applications, and stationary power stations, while the broad application is severely hindered by the sluggish kinetic of methanol oxidation reaction (MOR) in the anode and the high cost of platinum (Pt)-based anodic electrocatalysts. Herein, a series of carbon supported Pt_xCu_y (Pt_xCu_y/C) binary metal electrocatalysts, featured with high …

Electrochemical Synthesis Of P-(Β-Hydroxyethyl Sulfone) Aniline, Hao Guo, Dong-Fang Niu, Shuo-Zhen Hu, Xin-Sheng Zhang

Journal of Electrochemistry

Para-ester is the most important intermediate for the preparation of ethylene sulfone type reactive dyes, which is usually used in the dyeing of cellulose fibers and synthetic fibers. P-(β-hydroxyethyl sulfone) aniline is an important intermediate for the synthesis of para-ester. In this paper, p-(β-hydroxyethyl sulfone) aniline was prepared by electrochemical method, having the advantages of simple process, mild reaction condition, less environmental pollution, easy reaction control and so on. It has strong development potential and industrial application prospect. The electrochemical reduction of p-nitrophenyl-β-hydroxyethyl sulfone on a lead plate electrode to prepare p-(β-hydroxyethyl …

Synthesis Of Nickel Phosphide/Nitrogen Phosphorus Co-Doped Carbon And Its Application In Lithium Ion Batteries, Jian Hu, Yan-Shuang Meng, Qian-Ru Hu

Journal of Electrochemistry

In recent years, the nickel-based phosphide has drawn great attention because of its low intercalation/deintercalation platform and lower polarization compared to sulfides and oxides as anodes for next-generation high-energy lithium-ion batteries. The Ni₂P anode can deliver high theoretical specific capacity of 542 mAh·g^-1, but it subject to a conversion reaction mechanism, which make them unsuitable for commercial applications. The agglomeration of Ni₂P nanoparticles during material fabrication and the structural deterioration of electrode associated with large volume change during charge-discharge process lead to poor cycle stability and low utilization of active materials. Meanwhile, the low …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Development And Characterization Of Composite Membranes For Use In Countercurrent Solvent Extraction, Lydia Neves Rodrigues

Dissertations

Porous membranes having a particular wetting characteristic, hydrophobic or hydrophilic, are used for nondispersive membrane solvent extraction (MSX) where two immiscible phases flow on two sides of the membrane. The aqueous-organic phase interface across which solvent extraction/back extraction occurs remains immobilized on one surface of the membrane. This process requires the pressure of the phase not present in membrane pores to be either equal to or higher than that of the phase present in membrane pores; the excess phase pressure should not exceed a breakthrough pressure. In countercurrent MSX with significant flow pressure drop in each phase, this often poses …

One-Pot Synthesis Of Fe2O3@Fe-N-C Oxygen Reduction Electrocatalyst And Its Performance For Zinc-Air Battery, Hua Lin, Yi-Jin Wu, Jun-Tao Li, Yao Zhou

Journal of Electrochemistry

Oxygen reduction reaction (ORR) plays a profound role in determining cathode performance in metal-air batteries and fuel cells. Owing to its inherently sluggish kinetics, high-performance ORR catalysts which favors the scissoring of O-O bond and formation of O-H bond are a requisite. In this regard, Pt has been explored as the most efficient ORR electrocatalysts. Nevertheless, due to its expensiveness, the usage of Pt catalysts represents one of the major sources of cost in those energy conversion devices. Thus, the development of alternative ORR electrocatalysts with minimized Pt utilization has been widely pursued over the past few decades. Metal-nitrogen-carbon catalysts …

Dft Study Of NiM@Pt1AuN-M-1 (N=19, 38, 55, 79; M = 1, 6, 13, 19) Core-Shell Orr Catalyst, Wen-Jie Li, Dong-Xu Tian, Hong Du, Xi-Qiang Yan

Journal of Electrochemistry

The slow kinetics of oxygen reduction reaction (ORR) limits the performance of low temperature fuel cells. Thus, it needs to design effective catalysts with low cost. Core-shell clusters (CSNCs) show promising activity because of their size-dependent geometric and electronic effects. The ORR activity trend of Ni_m@Pt₁Au_n-m-1(n = 19, 38, 55, 79; m = 1, 6, 13, 19) was studied using the GGA-PBE-PAW methods. The adsorption configurations of *O, *OH and *OOH were optimized and the reaction free energies of four proton electron (H⁺ + e^-) transfer steps …

Preparation And Electrochemical Evaluation Of Mos2/Graphene Quantum Dots As A Catalyst For Hydrogen Evolution In Microbial Electrolysis Cell, Hong-Yan Dai, Hui-Min Yang, Xian Liu, Xiu-Li Song, Zhen-Hai Liang

Journal of Electrochemistry

Microbial electrolysis cell (MEC) is a relatively new bioelectrochemical technology that produces H₂ and meanwhile treats organic wastewater. Cathode hydrogen evolution catalyst plays a key role in MEC. The doping of Graphene Quantum Dots (GQDs) into MoS₂ nanosheets can improve the catalytic activity of MoS₂ by creating abundant defect sites both in the edge plane and the basal plane, as well as enhancing the electrical conductivity. In this paper, using Na₂MoO₄ , cysteine and GQDs as raw materials, a series of MoS₂/GQDs composites were firstly synthesized via hydrothermal method, and then loaded …

Preparation Of Coo/Rgo@Ni Foam Electrode And Its Electrocatalytic Reduction Of Co2, Qian Guo, Jia-Long Fu, Cheng-Yan Zhang, Chao-Yue Cai, Cheng Wang, Li-Hua Zhou, Rui-Bo Xu, Ming-Yan Wang

Journal of Electrochemistry

The worldwide extensive release of carbon dioxide (CO₂) has caused serious environmental pollution and unprecedented climate change problems. Thus, for the sustainable development of human society, it is very necessary to convert CO₂ to renewable fuels through clean and economical processes. The electrochemical CO₂ reduction reaction (CO₂RR) is regarded as a promising approach for the recycling of carbon resource and the generation of sustainable fuels. However, the slow kinetics and formation of multiple products in CO₂RR hinder its large-scale application. Hence, great research efforts are made to develop electrocatalysts with high product …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Electrochemical Deposition In Energy Storage Devices, Witness Atutala Martin

Graduate Theses and Dissertations

Metals, whether in a solid or soluble ion form, are a vital part of any electrochemical storage system. More so, Li metal is widely considered as the ideal anode because of its low density and low electrochemical potential (-3.04 V vs. the standard hydrogen electrode – SHE). However, just like most metals, it does not plate or strip evenly during cycling which can lead to cycling performance issues, short cycling lifespans, and even safety concerns brought about by dendrites that can cause internal short-circuiting within cells. This research focused on investigating the electroplating of metals in both aqueous and non-aqueous …

Synthesis And Electrochemical Study Of Cuau Nanodendrites For Co2 Reduction, Dylan Siltamaki, Shuai Chen, Farnood Rahmati, Jacek Lipkowski, Ai-Cheng Chen

Journal of Electrochemistry

The conversion of carbon dioxide (CO₂) to carbon monoxide (CO) and other value-added products is an interesting approach for carbon-containing fuel synthesis using renewable and clean energy. The electrochemical reduction of CO₂ is one of the promising strategies for the storage of intermittent renewable energy resources. The development of electrocatalysts with high activity and stability is vital in the electrochemical CO₂ reduction process. In this study, copper and gold alloyed (CuAu) electrodes with nanodendritic structures were synthesized using a facile electrodeposition method. The CuAu nanodendrites with the atomic ratio of Cu to Au being approximately 1:1 …

Preparation Of Co1-XS-Mns@Cnts/Cnfs For Electrocatalytic Oxygen Reduction Reaction, Fang-Yan Liu, Qian Zhang, Yue-Kun Li, Feng Huang, Meng-Ye Wang

Journal of Electrochemistry

As an important cathode reaction in fuel cells and metal-air batteries, oxygen reduction reaction (ORR) is a complex reaction of slow kinetics, which severely limits performances of fuel cells and metal-air batteries. Therefore, it is of key importance to find an efficient and stable electrocatalyst to promote ORR. Carbon-based materials, which possess high conductivity, good stability and large specific surface area, are usually used in electrocatalytic ORR. However, pure carbon-based materials exhibit low efficiency. Coupling carbon-based materials with manganese (Mn) and cobalt (Co) transition metals containing 3d orbitals is an effective way to improve electrocatalytic performance. Herein, carbon nanofibers containing …

Recent Advances In Glycerol Electrooxidation On Pt And Pd: From Reaction Mechanisms To Catalytic Materials, Wei-Yi Zhang, Xian-Yin Ma, Shou-Zhong Zou, Wen-Bin Cai

Journal of Electrochemistry

The conversion of glycerol to value-added products has received considerable attention recently because the booming biodiesel industry produces a large amount of glycerol as a byproduct. Among various means, electrocatalytic oxidation of glycerol is appealing owing to its environmental friendliness and high efficiency. However, electrooxidation of glycerol is very complex, involving multiple electron and proton transfer processes with many reaction pathways. How to rationally design catalysts with high selectivity toward targeted products is an overarching challenge, and of both fundamental and practical significance. In this minireview we aim to provide an overview of recent advancements in electrooxidation of glycerol focusing …

Pd-Based Electrocatalysts For Oxygen Reduction And Ethanol Oxidation Reactions: Some Recent Insights Into Structures And Mechanisms, Zhi-Peng Wu, Chuan-Jian Zhong

Journal of Electrochemistry

The development of efficient electrocatalysts for applications in fuel cells, including proton-exchange membrane fuel cell (PEMFC) and direct ethanol fuel cell (DEFC), has attracted extensive research attention in recent years. Oxygen reduction reaction and ethanol oxidation reaction are two of the key reactions where the design of active, stable and low-cost electrocatalysts is critical for the mass commercializations of PEMFCs and DEFCs. This challenge stems largely from the limited understanding of the catalyst structures and reaction mechanisms. Progress has been made in investigations of electrocatalysts derived from Pd-based alloy nanomaterials both experimentally and computationally. We highlight herein some of the …

Theoretical Studies Of Metal-N-C For Oxygen Reduction And Hydrogen Evolution Reactions In Acid And Alkaline Solutions, Xue-Ping Qin, Shang-Qian Zhu, Lu-Lu Zhang, Shu-Hui Sun, Min-Hua Shao

Journal of Electrochemistry

Single atom catalysts (SAC) have been regarded as the promising alternatives to platinum group metals due to their low costs and potentially high catalytic activities in various electrocatalytic reactions. The atomic mechanism understanding of activity discrepancy among different metal and nitrogen co-doped carbon-based catalysts is still lacking. Here, non-precious metal and nitrogen co-doped carbons (Me-N-C, Me = Fe and Co) as the model catalysts are investigated by combining experimental and theoretical studies to explore the catalytic activities and corresponding reaction mechanisms toward oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) at universal pHs. Atomic theoretical simulations suggest that Fe-N-C …

Oxygen-Exposure Induced Rapid Oxidation Of Spiro-Ometad In Cspbibr2 Perovskite Solar Cells, Wei-Guo Wang, Tian Bai, Gao-Fei Xue, Mei-Dan Ye

Journal of Electrochemistry

2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenyl-amine)-9,9′-spirobifluorene (Spiro-OMeTAD) is the most widely used hole transport material in perovskite solar cells (PSCs). However, its oxidation in the air takes a long time and results in the attack of perovskite by water. In this regard, we performed the oxidation process of Spiro-OMeTAD in oxygen, where perovskite can be protected from water, guaranteeing the integrity of perovskite. It was demonstrated that the champion Spiro-OMeTAD based CsPbIBr₂ PSCs after oxygen oxidation achieved a 7.19% power conversion efficiency (PCE), showing a higher PCE than 6.29% of the champion device oxidized in air. A series of electrochemical characterization methods were applied …

Application Of Atomically Precise Metal Nanoclusters In Electrocatalysis, Zhi-Hua Zhuang, Wei Chen

Journal of Electrochemistry

Metal nanoclusters (M NCs) consist of only several to a few hundred of metal atoms and possess core sizes less than 2 nm. Owing to the quantum size effect, the electronic states of M NCs evolve to discrete levels similar to the molecule energy gaps, other than a continuous density of states to produce plasmon characteristic of bulk metal nanoparticles (M NPs). In comparison with the conventional M NPs, M NCs exhibit dramatically unique electronic and optical properties, such as molecule-like energy gaps, strong photoluminescence and high catalytic properties, which make them promising for potential application in numerous fields, such …

Preparation Of Pdcoir Tetrahedron Nanocatalysts And Its Performance Toward Ethanol Oxidation Reaction, Zhi-Yuan Yu, Rui Huang, Jie Liu, Guang Li, Qian-Tong Song, Shi-Gang Sun

Journal of Electrochemistry

As a new energy conversion device, direct ethanol fuel cells (DEFCs) are widely concerned because of their remarkable advantages such as high theoretical energy density and wide fuel sources. However, the rapid development of DEFCs has been severely impeded due to the sluggish kinetic process and toxic intermediates especially in their anodic reactions. Palladium (Pd)-based materials are considered to be excellent anode catalysts for DEFCs, especially under alkaline conditions. And further improving their performance is an important direction to promote the development of DEFCs. Surface structure and composition are the key factors affecting the performance of catalysts which can be …

Research Progress In Electrodeposition Technology Of Titanium-Based Iridium Oxide Electrode, Dan-Dan Wu, Xu Wu

Journal of Electrochemistry

Titanium-based iridium oxide electrode has been widely used in various fields, such as electrocatalytic oxidation, biomedical applications, hydrometallurgical metal recovery, electro-osmotic dewatering, etc. At present, it is mainly prepared by traditional thermal decomposition method, however, which has high cost, cumbersome process, mainly relying on manual labor and cannot be mass-produced yet. It is, therefore, urgently necessary to explore new preparation technologies by focusing on electrodeposition technology, with technological characteristics such as eco-friendly and sustainable development. This article systematically discusses the research progress in iridium oxide electrodeposition preparation technology from the aspects of deposition solution formulation, base material selection and treatment, …