Chemical Engineering Commons^™

Syntheses Of Na3V2(Po4)2O2F As A Cathode For Sodium Ion Battery Application, Kai Wu

Journal of Electrochemistry

High-temperature solid-state method, hydro-thermal method and solvo-thermal method have been mainly employed to synthesize Na₃V₂(PO₄)₂O₂F (NVPF) cathode materials. However, these methods are energy consuming and complicated, which is not applicable for a large scale industrial production. In this study, a rather low-temperature (70℃) co-precipitation strategy was proposed to synthesize NVPF cathode materials. The as-prepared NVPF cathode materials showed a spherical shape with a diameter of 400 ~ 500 nm, and exhibited a sodium storage of 105.6 mAh·g^-1 and an efficiency of 90.06%. After a simple thermal process, the specific …

Fingering Behavior Of Flame Spread Over Solid Combustibles, Tsuneyoshi Matsuoka, Kentaro Nakashima, Takuma Kajimoto, Akihiro Yoshimasa, Yuji Nakamura

Progress in Scale Modeling, an International Journal

In this study, the fingering pattern formation and the following flamelet spreading over three different kinds of thick combustibles, i.e., Poly methacrylate (PMMA), Poly ethylene (PE) and Poly carbonate (PC) were observed and the effective Lewis number correlation was validated. Experiments were performed with a narrow channel apparatus. In addition to the kinds of solid fuel materials, the channel height and the oxidizer velocity were varied as experimental parameters. An image analysis method was developed to quantify the number, diameter and spread rate of the flamelets. Replacing the fuel thickness into the thermal thickness, the effective Lewis number which is …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …

Determination Of Hydrogel Degradation By Passive Mechanical Testing, Avery Rosh-Gorsky

Honors Theses

This paper details a new technique to measure the mechanical properties of ETTMP PEGDA hydrogels using Hertz Contact Theory and simultaneously analyze both the model drug release and gel erosion in situ. This method involves curing a drug loaded hydrogel in a standard cuvette and placing a glass bead and phosphate buffer solution (PBS). Over time, the cross-linked network of the hydrogel breaks down, and, as a result, the ball sinks into the hydrogel. This method provides a macroscopic and inexpensive way to continuously and passively measure properties of the hydrogel as the hydrogel degrades. By plotting both the …

Development Of An Injectable Methylcellulose Hydrogel System For Nucleus Pulposus Repair And Regeneration, Nada A. Haq-Siddiqi

Dissertations and Theses

Low back pain is the most common cause of disability in the world and is often caused by degeneration or injury of the intervertebral disc (IVD). The IVD is a complex, fibrocartilaginous tissue that allows for the wide range of spinal mobility. Disc degeneration is a progressive condition believed to begin in the central, gelatinous nucleus pulposus (NP) region of the tissue, for which there are few preventative therapies. Current therapeutic strategies include pain management and exercise, or surgical intervention such as spinal fusion, none of which address the underlying cause of degeneration. With an increasingly aging population, the socioeconomic …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research focuses on the synthesis of both shaped and amorphous powder materials, the combination of these materials with dried Powder River Basin (PRB) coal char, and their reactionary properties with methane and carbon dioxide gasses with conventional and microwave (MW) heating. The first goal of this project was to synthesize shaped micro and nano sized particles with ideal dielectric properties for converting electromagnetic energy into heat and proven capabilities of activating methane. These particles were synthesized via solvothermal, hydrothermal, and co-preceptory treatments alone and onto the surface of dried PRB coal char. PRB is a sub-bituminous, low-ranking coal (LRC) …

Effect Of Reaction Conditions On Cu⁃Catalyzed Co2 Electroreduction, Chang Zhu, Wei Chen, Yan-Fang Song, Xiao Dong, Gui-Hua Li, Wei Wei, Yu-Han Sun

Journal of Electrochemistry

Electrochemical conversion of carbon dioxide (CO₂) driven by renewable electricity that can meet both carbon emission reduction and renewable energy utilization has been rapidly developed in recent years. Copper (Cu) catalyst has long been a promising candidate for CO₂ electroreduction applications because of its natural abundance and specific capability of producing a substantial amount of C2 products. However, various metallic Cu electrodes reported have been significantly influenced by the adsorption of certain cation/anion ions, resulting in wide-span catalytic activities and selectivity for various products. In addition, a recent report demonstrated that by virtue of gas-diffusion flow cell …

Numerical Simulations Of Current And Temperature Distribution Of Symmetrical Double-Cathode Solid Oxide Fuel Cell Stacks Based On The Theory Of Electric-Chemical-Thermal Coupling, Cheng-Rong Yu, Jian-Guo Zhu, Cong-Ying Jiang, Yu-Chen Gu, Ye-Xin Zhou, Zhuo-Bin Li, Rong-Min Wu, Zheng Zhong, Wan-Bing Guan

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) is a high-efficient clean conversion device for future energy management. Because of the low antioxidant reduction ability and complex thermal stress, the structure of traditional asymmetrical thin anode-supported planar SOFC is easily to be broken under stack operating conditions. To overcome these defects, a new complete symmetrical SOFC based on double-sided cathodes was developed. To study the influences of gas flow direction and current collection mode on the cell performance inside stack, a numerical model was established by finite element method based on the theory of electro-thermo-chemo multiphysical coupling. By applying this model, the molar …

Core-Shell Structured Ru@Ptru Nanoflower Electrocatalysts Toward Alkaline Hydrogen Evolution Reaction, Xue-Liang Wang, Yuan-Yuan Cong, Chen-Xi Qiu, Sheng-Jie Wang, Jia-Qi Qin, Yu-Jiang Song

Journal of Electrochemistry

Water electrolysis for hydrogen production is beneficial for solving the problem of energy crisis and environmental issues. It is necessary to study highly active and cost-effective catalysts toward hydrogen evolution reaction (HER) to reduce the consumption of noble metals. Herein, we report the synthesis of core-shell structured Ru@Pt_0.24Ru nanoflowers electrocatalyst by stepwise reduction of Ru and Pt precursors in the mixture of oleylamine and benzyl alcohol at 160 ^oC. The average diameter of the resultant Ru@Pt_0.24Ru was 16.5±4.0 nm with a bulk atomic ratio between Pt and Ru of 0.24:1 and a surface ratio of …

An Improved Foam Modeling Technique And Its Application To Petroleum Drilling And Production Practice, Yanfang Wang

LSU Doctoral Dissertations

Foam is one of the most common used multiphase fluid in Underbalanced Drilling (UBD) and Managed Pressure Drilling (MPD). Because of its low density, high capacity of lifting and carrying cuttings, low cost and compatibility with formations, foam has become more superior than the conventional drilling mud when depleted reservoir pressure, severe lost circulation, or unstable borehole are encountered. In general, the success of foam applications rely on the understanding of the fundamentals of foam rheology in downhole conditions.

Foam rheology has been studied for decades. Conventional foam rheological models such as Power Law, Bingham Plastic, Herschel-Bulkley to explain foam …

Enhancement Of Regeneration Ratio And Thermal Durability For Regenerated Fiber Bragg Grating Based On Pre-Annealing Treatment And Multimaterial Fibers, Nurul Asha Mohd Nazal

Student Works (2020-2029)

Regenerated fiber Bragg grating (RFBG) or also known as regenerated grating (RG) is the creation of the temperature resistant grating through thermal erasure of seed grating (SG) followed by a rebirth of new grating in a annealing process. RG has shown to be a promising fiber Bragg grating component for operation under very high ambient temperature condition. Nonetheless, further investigation and improvement are required to better understand its formation mechanism and to enhance its performance. This study aims to enhance the regeneration ratio and thermal durability of the RG based on pre-annealing treatment and multimaterial fiber. In this work, the …

Homotopy Simulation Of Dissipative Micropolar Flow And Heat Transfer From A Two-Dimensional Body With Heat Sink Effect: Applications In Polymer Coating, O. A. Bég, B. Vasu, A. K. Ray, T. A. Beg, A. Kadir, H. J. Leonard, Rama S. R. Gorla

Faculty Publications

Non-Newtonian flow from a wedge constitutes a fundamental problem in chemical engineering systems and is relevant to processing of polymers, coating systems, etc. Motivated by such applications, the homotopy analysis method (HAM) was employed to obtain semi-analytical solutions for thermal convection boundary layer flow of incompressible micropolar fluid from a two-dimensional body (wedge). Viscous dissipation and heat sink effects were included. The non-dimensional boundary value problem emerges as a system of nonlinear coupled ordinary differential equations, by virtue of suitable coordinate transformations. The so-called Falkner-Skan flow cases are elaborated. Validation of the HAM solutions was achieved with earlier simpler models, …

Adsorption And Reconfiguration Of Amphiphiles At Silica-Water Interfaces: Role Of Electrostatic Interactions, Van Der Waals Forces And Hydrogen Bonds, Yao Wu

LSU Doctoral Dissertations

The ability to explore and predict metastable structures of hybrid self-assemblies is of central importance for the next generation of advanced materials with novel properties. As compared to their thermodynamically stable forms, the kinetically stabilized materials show improved functionality potentially over their stable counterparts. The self-assembly processes usually originate from weak intermolecular interactions, involving a dynamic competition between attractive and repulsive interactions. These weak forces, including van der Waals (vdW), electrostatic interaction and the hydrogen bonding (H-bonding), can be tuned by external stimuli, e.g., confinement, temperature and ionization, and consequently driving hybrid materials into different configurations. It is challenging to …

A Model For The Anodic Carbonization Of Alkaline Polymer Electrolyte Fuel Cells, Qi-Hao Li, Ying-Ming Wang, Hua-Long Ma, Li Xiao, Gong-Wei Wang, Jun-Tao Lu, Lin Zhuang

Journal of Electrochemistry

The alkaline polymer electrolyte fuel cell (APEFC) has made appreciable progress in recent years but is still suffering performance loss during discharge with air as the oxidant. Several theories have been suggested to interpret the loss. However, efforts are still needed to reach a clear quantitative understanding. Based on the major experimental findings in combination with thermodynamics and kinetics of the reactions involved in the anode, this paper presents a model featuring layered carbonization in the anode and relevant grouped equations. The simulation results generated from the latter are compared with experiments, and possible principles to suppress the performance loss …

Facile Synthesis Of Nitrogen-Doped Graphene-Like Active Carbon Materials For High Performance Lithium-Sulfur Battery, Quan-Hua Meng, Wen-Wen Deng, Chang-Ming Li

Journal of Electrochemistry

Lithium-sulphur (Li-S) battery is regarded as a promising energy storage device because of its high theoretical capacity. However, the low S utilization and short cycling life limit the commercial applications. In this work, nitrogen-doped graphene-like carbon (NGC) materials were synthesized by simply pyrolyzing and carbonizing the mixture of melamine (C₃H₆N₆) and L-cysteine (C₃H₇NO₂S). The graphene-like structure in NGC effectively buffered the volume change of S during the discharge/charge process and improved the cycling stability. Meanwhile, nitrogen-containing functional groups in NGC facilitated the transportation of ions and suppressed the …

Preparation Characterization And Tribological Behavior Of Lube Oil With Nanoparticles Additives, Waleed Alghani

Student Works (2020-2029)

There are many companies worldwide that would like to improve and upgrade the lube oil and enhance its performance. There is a big concern for the enhancement of lube oil by using nanotechnology and more precisely with using nanomaterial additives. Much work has made to explore and develop new sorts of lubricating oil nano-additives to diminish wear and friction in tribological configurations and to enhance surface morphology. It has noted that the use of dual nano-additives should examine the lubricating capacity and durability of lubricant. (TiO2 Anatase + Graphene) and (ZnO + Graphene) nanoparticles have selected to formulate nano-additives that …

Recent Progress In Bifunctional Catalysts For Zinc-Air Batteries, Neng-Neng Xu, Jin-Li Qiao

Journal of Electrochemistry

Zinc-air battery has attracted great attention from researchers due to its high energy density and power density, which is expected to be widely used in energy conversion and storage. Air electrode as the core area of oxygen catalytic reaction is the focus of the entire zinc-air battery research. Recently, many research achievements have been made in non-noble metal bifunctional catalysts/electrodes with high activity, low cost and abundant species. In this review, we mainly focus on the reaction mechanism and the recent progress in non-noble metal oxide catalyst, carbon-based catalyst, and carbon-based transition metal compound composite and self-supporting electrode. In addition, …

Electrochemical Carbon Dioxide Reduction In Flow Cells, Jia Fan, Na Han, Yan-Guang Li

Journal of Electrochemistry

Electrochemical carbon dioxide reduction (CO₂RR) is an appealing approach to convert atmospheric CO₂ to value-added fuels and industrial chemicals, and may play an important role during the transition to a carbon-neutral economy. In order to make this technology commercially viable, it is essential to pursue CO₂RR in flow reactors instead of conventional H-type reactors, and to combine electrocatalyst development with system engineering. In this review, we overview the cell configurations and performance advantages of the two types of flow reactors, analyze their shortcomings, and discuss the effects of their different components including gas diffusion electrode …

Recent Progress On Enhancing Effect Of Nanosized Metals For Electrochemical Co2 Reduction, Yu-Ning Zhang, Dong-Fang Niu, Shuo-Zhen Hu, Xin-Sheng Zhang

Journal of Electrochemistry

The electrochemical conversion of CO₂ to chemical raw material for further utilization shows promising future to alleviate global warming and realize carbon cycle in nature, which is of great significance to the green chemistry and sustainable development. This review briefly introduces the advantages of CO₂ electrochemical reduction (CO₂ER) and its basic reaction principles, and summarizes the recent progress in a series of activity enhancement strategies based on nanosized metal catalysts. The influences of alloy effect, interface engineering, synergistic effect, surface defect engineering and support effect on the catalytic performance of nanosized metals for CO₂ER …

Electrolyte Tailoring For Electrocatalytic Reduction Of Stable Molecules, Jin-Han Li, Fang-Yi Cheng

Journal of Electrochemistry

Reduction of stable molecules such as CO₂ and N₂ is important process in electrochemical energy conversion and storage technologies for electrofuels production. However, for the inert nature of CO₂/N₂ molecule and competitive proton reduction in conventional aqueous electrolytes, selective electrochemical carbon/nitrogen fixation suffers from high overpotential, low reaction rate and low selectivity. While addressing these issues has witnessed substantial advances in electrocatalysts, much less attention has been placed on the electrolytes, which play an important role in regulating the local environment and thus the performance of catalysts under operating conditions. Rational design of electrolytes has …

Research Progress Of Metal-Nitrogen-Carbon Catalysts Toward Oxygen Reduction Reaction Inm Changchun Institute Of Applied Chemistry, Ming-Jun Xu, Jie Liu, Jun-Jie Ge, Chang-Peng Liu, Wei Xing

Journal of Electrochemistry

The development of highly active and stable catalysts toward oxygen reduction reaction (ORR) has been facing severe challenges. In recent years, pyrolytic M-N-C catalysts and metal-organic framework derived materials made the performance of non-noble metal catalysts greatly improved, however, the molecular and atomic level understanding in the reaction active sites and the mechanism are still lacking. Here, we summarize the recent research progress made in the Changchun Institute of Applied Chemistry. We present a microporous metal-organic-framework confined strategy toward the preferable formation of ORR catalysts. Firstly, we studied the active site and proposed a new active site structure for the …

Fuel Cell Performance Of Non-Precious Metal Based Electrocatalysts, Yan-Feng Zhang, Fei Xiao, Guang-Yu Chen, Min-Hua Shao

Journal of Electrochemistry

The commercialization of proton exchange membrane fuel cells (PEMFCs) is hindered by high cost and low durability of Pt based electrocatalysts. Developing efficient and durable non-precious metal catalysts is a promising approach to addressing these conundrums. Among them, transition metals dispersed in a nitrogen (N)-doped carbon support (M-N-C) show good oxygen reduction reaction activity. This article reviews recent progress in M-N-C catalysts development, focusing on the catalysts design, membrane electrode assembly fabrication, fuel cell performance, and durability testing. Template-assisted approach is an efficient way to synthesize M-N-C materials with homogeneously dispersed single atom active site and reduced metal particles, carbides …

Preparations Of Nano-MnoX/Ti Electrocatalytic Membrane Electrode For Catalytic Oxidation Of Cyclohexane Using Intermittent Electrodeposition, Xue Zhou, Hong Wang, Zhen Yin, Yu-Jun Zhang, Jian-Xin Li

Journal of Electrochemistry

Cyclohexanone and cyclohexanol (KA oil) obtained from highly selective oxidation of cyclohexane (CHA) show important industrial value and application prospects. In this work, the intermittent electrodeposition was developed to prepare nano-MnO_x catalyst loading porous tubular titanium membrane electrode (MnO_x/Ti), which was employed to constitute an electro-catalytic membrane reactor (ECMR) for the oxidation of cyclohexane to produce cyclohexanol and cyclohexanone. The surface morphology, crystal structure and electrochemical property of the catalysts were characterized by FESEM, XRD and electrochemical workstation, respectively. The results show that the catalyst prepared by the intermittent electrodeposition displayed nano-flower-like γ-MnO₂. Compared with …

Preparation Of Α-Hydroxylated Acetal From 2-Butanone By Indirect Electrooxidation, Hai-Qing Huang, Ye Miao, Xin-Sheng Zhang

Journal of Electrochemistry

Acetoin (3-hydroxy-2-butanone) is an important food spice. As a platform compound, it is widely used in medicine, tobacco, cosmetics, chemical material and other industries. In this paper, α-hydroxylated acetal, an intermediate of acetoin, was prepared from 2-butanone by indirect electrooxidation in the plate and frame electrolytic cell, in which graphite plates were used as both an anode and a cathode, while KOH as an electrolyte and KI as a catalyst. Acetoin could be prepared by hydrolysis in acidic aqueous solution from acetoin intermediate. The effects of current density, electrolyte flow rate between the plates, 2-butanone concentration and electrolysis temperature …

Electrochemical Oxidation Of Metal Chromium In Odium Hydroxide Aqueous Solution, Ping Han, Hai-Tao Feng, Ya-Ping Dong, Sen Tian, Bo Zhang, Wu Li

Journal of Electrochemistry

Ferrochrome electrolysis technology is a novel method for preparing sodium chromate (Na₂CrO₄). Although the method performs well at soft reaction conditions, controllable process, environmentally friendly production process, etc., the electrochemical oxidation process of metal chromium in NaOH aqueous electrolyte is still unclear. At present, there are few research articles about specific electrochemical oxidation of metal chromium in NaOH aqueous electrolyte. It is, therefore, meaningful to carry out the research in electrochemical oxidation mechanism of chromium. The electrochemical oxidation of metal chromium in 0.01 mol·L^-1 ~ 10 mol·L^-1 NaOH aqueous electrolytes at 20 °C was …

Poly(Ethylene Oxide) Based Polymer Electrolytes For All-Solid-State Li-S Batteries, Xue Li, Zheng-Liang Gong

Journal of Electrochemistry

In recent years, research on lithium-sulfur (Li-S) batteries has received much attention because the sulfur positive electrode and the lithium metal negative electrode produce a high theoretical specific capacity (lithium metal ~ 3800 mAh·g^-1, sulfur ~ 1675 mAh·g^-1). In addition, sulfur is considered to be the most promising cathode material for secondary lithium batteries, due to its advantages of low price and environmental friendly. However, the practical application of conventional liquid Li-S batteries is still obstructed by several critical issues, such as lithium ploysulfides shuttle effect, long-term stability of lithium metal anode with organic liquid electrolytes, …

Synthesis And Raman Study Of Hollow Core-Shell Ni1.2Co0.8P@N-C As An Anode Material For Sodium-Ion Batteries, Jia-Hui Chen, Xiao-Bin Zhong, Chao He, Xiao-Xiao Wang, Qing-Chi Xu, Jian-Feng Li

Journal of Electrochemistry

With the increasing demand for large-scale energy storage, great progress has been made in discovering new advanced energy storage materials. Sodium-ion batteries (SIBs) have attracted much attention in recent years due to their use of abundant sodium resources and their comparable electrochemical capacity to lithium-ion batteries (LIBs). In this paper, we developed novel hollow core-shell Ni-Co bimetallic phosphide nanocubes with N-doped carbon coatings (Ni_1.2Co_0.8P@N-C) as the anode material for SIBs. The material was synthesized through a low-temperature phosphorization method using resorcinol formaldehyde (RF) resin coating with a Ni-Co Prussian blue analogue (PBA) as a template and …

Stability Studies For A Membrane Electrode Assembly Type Co2 Electro-Reduction Electrolytic Cell, Qing Mao, Bing-Yu Li, Wei-Yun Jing, Jian Zhao, Song Liu, Yan-Qiang Huang, Zhao-Long Du

Journal of Electrochemistry

Electro-catalytic reduction is an efficient way to achieve resourcable transformation of CO₂, which is one of the important techniques to solve the global environmental problems originated from excessive CO₂ emission. In this study, a membrane electrode assembly(MEA) type CO₂ electro-reduction electrolytic cell was constucted, which enables CO₂ feeding and real-time KHCO₃ aqueous updating on both sides of the cathode gas diffusion electrode (GDE). By means of the electrolytic cell, effects of KHCO₃ concentration and updating inside the liquid electrolytic chamber on CO₂ electro-reduction activity, production distribution and stability were investigated. The experimental …

Calculating Elastic Properties Of Confined Simple Fluids, Christopher D. Dobrzanski

Dissertations

Confinement in nanoporous materials is known to affect many properties of the fluids confined within their pores. The elastic properties are no exception. This dissertation begins with an overview of the relevant literature on ways of obtaining elastic properties of confined fluids. It outlines some fundamental gaps in our understanding. The chapters following address some of these gaps in understanding elastic properties of the confined fluid, in particular, how the shape of the confining pore matters, how supercriticality effects the properties, how an equation of state designed for confined fluids can be used to calculate elastic properties, and if an …