Bioresource and Agricultural Engineering Commons^™

Vertical Loads Due To Wheat On Obstructions Located On The Floor Of A Model Bin, Marek Molenda, Michael D. Montross, Sidney A. Thompson, Jozef Horabik

Biosystems and Agricultural Engineering Faculty Publications

Tests were conducted in a model grain bin to evaluate the vertical loads acting on differently shaped obstructions embedded in wheat during filling, detention, and discharge. The bin had corrugated galvanized steel walls with a 1.83 m diameter and a flat bottom. All tests were conducted in a bin that was centrically loaded and unloaded. Three differently shaped obstructions (disc, cone, and cylinder) were tested; each had a circular base equivalent to 6% of the bin floor area. The obstructions were supported in the bin using a three-legged support structure. Each leg of the support structure rested on a load …

Air Exchange Rate In A Horse Trailer During Road Transport, Joseph L. Purswell, Richard S. Gates, Laurie M. Lawrence, Jamey D. Jacob, Timothy S. Stombaugh, Robert J. Coleman

Biosystems and Agricultural Engineering Faculty Publications

Horses traveling by road commonly experience heat stress conditions and poor air quality, which may be caused by insufficient ventilation; however, there are few estimates of air exchange in a horse trailer during transport. Air exchange rate was measured at ten locations within a four-horse trailer (internal volume 18.5 m³) using tracer gas decay measurement to assess the adequacy of ventilation. Three vehicle speeds (13, 48, and 97 km h^-1) and three window configurations (all windows and roof vents closed, all windows open, all windows open and roof vents open forward) were tested with and without …

Distribution Pattern Variability Of Granular Vrt Applicators, John P. Fulton, Scott A. Shearer, Stephen F. Higgins, Dennis Wayne Hancock, Timothy S. Stombaugh

Biosystems and Agricultural Engineering Faculty Publications

Granular applicators equipped with variable-rate technology (VRT) have gained popularity in recent years as a result of increased interest in variable-rate application. The purpose of this investigation was to characterize distribution patterns at varying rates for different granular applicators. Uniform-rate (UR) tests were conducted to assess the accuracy of variable-rate application from four granular applicators: two spinner-disc spreaders (A and B), and two pneumatic applicators (C and D). Pattern results indicated a consistent triangular pattern for spinner spreader B and consistent patterns for the pneumatic applicators (C and D). However, applicator D produced pattern variations at the center and right …

Rate Response Assessment From Various Granular Vrt Applicators, John P. Fulton, Scott A. Shearer, Stephen F. Higgins, Matthew J. Darr, Timothy S. Stombaugh

Biosystems and Agricultural Engineering Faculty Publications

Variable-rate technology (VRT) adds complexity to application equipment, thereby confounding the assessment of applicator performance. The intent of this investigation was to assess the rate response of various VRT granular applicators: two spinner spreaders (A and B), and two pneumatic applicators (C and D). Variable-rate (VR) tests were conducted to quantify the rate response characteristics (delay and transition times) for the applicators. A sigmoidal function was used to model the rate response for five of the six tests. Applicator A exhibited a linear response during decreasing rate changes. Results indicated that only applicator B demonstrated consistent delay and transition times, …

The Global Positioning System, Timothy S. Stombaugh, Doug Mclaren, Benjamin K. Koostra

Agricultural Engineering Extension Publications

The Global Positioning System (GPS) is quickly becoming part of the fabric of everyday life. Beyond recreational activities such as boating and backpacking, GPS receivers are becoming a very important tool to such industries as agriculture, transportation, and surveying. Very soon, every cell phone will incorporate GPS technology to aid first responders in answering emergency calls.

Spatial Variation Of Protein, Oil, And Starch In Corn, Samuel G. Mcneill, Michael D. Montross, Scott A. Shearer

Biosystems and Agricultural Engineering Faculty Publications

Significant spatial yield variations are known to exist in cornfields with different soil types, topsoil depth, and other variables. Similarly, variations might also be found among the highly valued chemical components (oil, protein, and starch) in corn kernels due to local differences in soil type, fertility, acidity/pH, organic matter, etc. This study quantified the spatial variability of protein, oil, and starch content of corn from two conventional cornfields and two high-oil cornfields. Whole ears were harvested by hand from 20 to 40 randomly selected locations within each field. A differential global positioning system (DGPS) receiver recorded the location of each …

Permeability Of Corn, Soybeans, And Soft Red And White Winter Wheat As Affected By Bulk Density, Michael D. Montross, Samuel G. Mcneill

Biosystems and Agricultural Engineering Faculty Publications

Darcy’s law is a function of viscosity, permeability, and velocity and can be used to predict the airflow resistance in granular materials at low air velocities. Permeability also governs the magnitude of natural convection currents during periods of non-aerated grain storage. The permeability of corn, soybeans, soft white winter wheat, and soft red winter wheat were measured as a function of bulk density and moisture content. Air was passed through a column of grain and the flow rate and pressure drop measured. Bulk density and kernel density were also measured to determine the porosity of grain in the test column. …

Airflow Resistance Of Seeds At Different Bulk Densities Using Ergun's Equation, Marek Molenda, Michael D. Montross, Samuel G. Mcneill, Jozef Horabik

Biosystems and Agricultural Engineering Faculty Publications

Airflow resistance of grains and oilseeds has been extensively studied. Traditionally the data has been presented using Shedd’s curves. However, this assumes that airflow resistance is independent of grain depth. Grain undergoes compaction during storage that changes the bulk density, porosity, and therefore the airflow resistance. Ergun’s equation is a function of particle size and porosity of the granular material. Airflow resistance by Ergun’s equation was used to predict the pressure drop across a column of corn, soft white winter wheat, soft red winter wheat, and soybeans at three moisture content levels and two bulk densities. The maximum root mean …

Crop Yield Response To Precision Deep Tillage, Larry G. Wells, Timothy S. Stombaugh, Scott A. Shearer

Biosystems and Agricultural Engineering Faculty Publications

Experimental precision deep tillage was applied at three sites in central Kentucky with relatively well-drained silt loam soils in no-till crop production. Fields were divided into 0.4 ha (1 ac) grid cells using DGPS mapping. Assessment of soil compaction by machinery traffic was made using multiple soil cone penetrometer measurements and expressed as cone index (CI). Corn, wheat, and soybean yields were depressed in grid cells with CI_avg ≥ 1.5 MPa (218 psi) prior to application of tillage treatments at sites 1 and 3, whereas at site 2, where most of the highest average CI values ranged from 1.44 …

Effect Of Fat And Casein Particles In Milk On The Scattering Of Elliptically Polarized Light, Czarena L. Crofcheck, Jeremie Wade, Janakiraman N. Swamy, Mustafa M. Aslan, M. Pinar Mengüç

Biosystems and Agricultural Engineering Faculty Publications

In this article, we present an experimental approach to determine the milk fat content using scattered light intensity profiles. The elements of the scattering (Mueller) matrix have been shown to provide valuable information about variation of the optical properties of scattering particles. The scattering behavior of fat and casein in terms of the scattering matrix elements was experimentally determined for milk with varying fat levels ranging from 0.05 wt% (skim) to 3.20 wt% (whole). Three of the scattering Mueller matrix elements, specifically S₁₁, S₁₂/S₁₁, and S₃₃/S₁₁, were found to be …

Moveable Tobacco Curing Frames, George A. Duncan, Larry D. Swetnam, Linus R. Walton

Agricultural Engineering Extension Publications

Moveable (or portable) curing frames offer the tobacco grower another option for successfully reducing labor and costs for producing air-cured tobacco. Reducing labor and costs is essential to continuing profitable tobacco production.

Two designs that use the cantilever-beam concept for supporting two rails of stick tobacco on a central beam are shown and explained in this publication. Further details of construction and covering are shown in the following drawings.

Controller Area Network Based Distributed Control For Autonomous Vehicles, Matthew J. Darr, Timothy S. Stombaugh, Scott A. Shearer

Biosystems and Agricultural Engineering Faculty Publications

The goal of this project was to evaluate the potential of a controller area network (CAN bus) to be used as the communication network for a distributed control system on an autonomous agricultural vehicle. The prototype system utilized microcontroller-driven nodes to act as control points along a CAN bus. Messages were transferred to the steering, transmission, and hitch control nodes via a task computer. The task computer utilized global positioning system data to generate appropriate control commands. Laboratory and field testing demonstrated that each of the control nodes could function simultaneously over the CAN bus. Results showed that the task …

Selecting An Air-Cure Tobacco Housing And Curing Facility, George A. Duncan, Larry D. Swetnam

Agricultural Engineering Extension Publications

Once or twice in a lifetime the average tobacco producer faces the decision of what tobacco housing and curing facility he needs to build. For some, this may be to replace a barn that has burned or blown down. For others, the need may arise from an expansion of production by farm acquisition or lease-in of extra poundage.

In all cases, it is important to build the most suitable facility for present and projected production methods. With labor becoming more costly and scarce, labor-saving features are a must Rising material and construction costs continue to increase the initial investment costs …

Measuring Relative Humidity In Agricultural Environments, George A. Duncan, Rich Gates, Michael D. Montross

Agricultural Engineering Extension Publications

Relative humidity is very important for many agricultural environments, such as fruit and vegetable storage facilities, greenhouses, and tobacco curing and handling facilities.

Several scientific instruments measure temperature and relative humidity. The more accurate the instrument, the more it will cost. Devices that are economical for agricultural use in a barn, greenhouse, or a semi-protected environment often do not hold their accuracy over very long periods (six months to a year or longer) if they are used carelessly.

Several instruments that are readily available and affordable for general farm use are described here. Often called hygrometers or hygro-thermometers, some …

Evaluation Of A Mechanical System For Reconstructing Soil On Surface Mined Land, John P. Fulton, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

The existence of excessive soil compaction has hindered the surface mining industry from returning land to pre−mining productivity after reclamation, especially on prime farmland soils. Heavy earthmoving equipment used during reclamation tends to generate root−limiting bulk densities that adversely affect plant growth thereby decreasing yields. Therefore, the purpose of this study was to evaluate a mechanism, called the ‘Soil Regenerator,’ which reconstructs soil media at minimum bulk density during surface mine reclamation. The prototype soil forming mechanism was mounted on the front of a conventional bulldozer. Soil was placed in long narrow windrows by a scraper or bulldozer. As the …

Aeration Strategies And Fan Cost Comparisons For Wheat In Mid-South Production Regions, Thomas C. Bridges, Michael D. Montross, Samuel G. Mcneill

Biosystems and Agricultural Engineering Faculty Publications

Numerous factors influence the sizing of aeration fans for summer-harvested crops. Thirty years of weather data for Lexington, Kentucky, were analyzed and the cost of aeration was compared for two axial fans (afan1, afan2) and one centrifugal fan (cfan1). Aeration costs were defined as the sum of the following components: the cost of owning the fan, the cost of electricity for operating the fan, a cost for wheat shrinkage during aeration, and a cost for dry matter loss (DML). The fans were selected to deliver airflow rates of approximately one, two, and three times the recommended aeration rate of 0.11 …

Streambank Erosion Associated With Grazing Practices In The Humid Region, Carmen T. Agouridis, Dwayne R. Edwards, Stephen R. Workman, José R. Bicudo, Benjamin K. Koostra, Eric S. Vanzant, Joseph L. Taraba

Biosystems and Agricultural Engineering Faculty Publications

The effects of cattle grazing on stream stability have been well documented for the western portion of the U.S., but are lacking for the east. Stream and riparian damage resulting from grazing can include alterations in watershed hydrology, changes to stream morphology, soil compaction and erosion, destruction of vegetation, and water quality impairments. However, few studies have examined the successes of best management practices (BMPs) for mitigating these effects. The objective of this project was to assess the ability of two common BMPs to reduce streambank erosion along a central Kentucky stream. The project site consisted of two replications of …

Vertical Wall Loads In A Model Grain Bin With Non-Axial Internal Inserts, Marek Molenda, Michael D. Montross, Jozef Horabik, Sidney A. Thompson

Biosystems and Agricultural Engineering Faculty Publications

A study was conducted to estimate the degree of load asymmetry in a bin with non-axial internal inserts. Internal inserts in the form of an annulus segment were attached to the wall, and their influence on vertical wall loads during centric filling and discharge in a model bin were measured. Wall and floor loads were measured in a corrugated-wall model grain bin with a diameter of 2.44 m and a height of 7.3 m filled with soft red winter wheat to a depth of 6.7 m (height-to-diameter ratio of 2.75). Tests were conducted with inserts that extended circumferentially 30°, 60°, …

Seasonal Aeration Rates For The Eastern United States Based On Long-Term Weather Patterns, Michael D. Montross, Samuel G. Mcneill, Thomas C. Bridges

Biosystems and Agricultural Engineering Faculty Publications

Most aeration fans are sized to produce a minimum airflow rate of 0.1 m³/min/t (0.1 cfm/bu) in on-farm grain storage structures. At this airflow rate a significant amount of time is required to move a cooling front completely through a bin. The desired grain temperature and prevailing weather conditions will have a significant effect on required fan size. Thirty years of weather data were analyzed for the eastern United States to determine the amount of time available in temperature windows between 0 to 15.C and 0 to 17.C. Contour maps were generated with ArcMap 8.3 for the percentage …

Suitability Of A Gps Collar For Grazing Studies, Carmen T. Agouridis, Timothy S. Stombaugh, Stephen R. Workman, Benjamin K. Koostra, Dwayne R. Edwards, Eric S. Vanzant

Biosystems and Agricultural Engineering Faculty Publications

The traditional means of tracking animal location in a field is by visual observation. Not only is this method labor intensive, it is also prone to error as the observer can alter cattle movement, observation periods are often too short to obtain confidence in general daily behavior patterns, and observer fatigue becomes an issue. In the 1990s, the University of Kentucky began using GPS collars on cattle to track their position with the goal of incorporating this information into cattle management practices. One of the key unanswered questions regarding the GPS collars is the accuracy of the position data recorded …

Post-Tier Rail And Typar® Or Metal-Covered Tobacco Field Curing Structures, George A. Duncan

Agricultural Engineering Extension Publications

Tobacco producers are rapidly adopting field curing structures with several variations in construction materials and methods. They are looking to lower costs and increase efficiency by installing structures that require less maintenance and last longer.

Two recently designed structures appear to provide more permanent options for producers who dislike the tedious tasks of covering and securing the plastic over the tobacco during the curing season. Both structures use two-rail-wide, two-post wooden construction, but they differ in their roof coverings. One uses Typar®, and the other uses metal.

Effect Of Moisture Content And Broken Kernels On The Bulk Density And Packing Of Corn, Samuel G. Mcneill, Sidney A. Thompson, Michael D. Montross

Biosystems and Agricultural Engineering Faculty Publications

Shelled yellow dent corn samples were conditioned to three moisture content levels (12%, 15%, and 18% w.b.) and mixed with a prescribed amount of broken corn particles of known size (geometric mean diameter of 1.0, 1.4, 2.0, 2.8, and 4.0 mm) and concentration (2.5%, 5.0%, and 7.5% by weight) levels. The initial bulk density and grain compaction under simulated overburden pressure tests were determined for each sample. Uniaxial compression tests were performed for seven vertical pressure levels (3.4, 6.9, 14, 28, 55, 110, and 165 kPa) with a minimum of three replications each. Tests were performed at two locations with …

The Influence Of Environmental Temperature And Substrate Initial Moisture Content On Aspergillus Niger Growth And Phytase Production In Solid−State Cultivation, Seaborn B. Carter, Sue E. Nokes, Czarena L. Crofcheck

Biosystems and Agricultural Engineering Faculty Publications

Aspergillus niger is being used commercially for phytase production utilizing solid-state cultivation; however, no studies have been published that investigated the optimal environmental temperature and initial substrate water content to maximize fungal growth and/or phytase production. Solid-state cultivations of Aspergillus niger on wheat bran and soybean meal were conducted at three temperatures (25°C, 30°C, and 35°C) and three initial moisture contents (50%, 55%, and 60% wet basis) in a split-plot full-factorial experimental design. Fermentations were conducted for 0, 24, 48, 72, and 120 h. The containers were sampled destructively and assayed for phytase activity and glucosamine concentration as an estimate …

Effect Of Stover Fraction On Glucose Production Using Enzymatic Hydrolysis, Czarena L. Crofcheck, Michael D. Montross

Biosystems and Agricultural Engineering Faculty Publications

Corn stover was fractionated into three fractions: cobs, stalks, and leaves and husks. The fractions were dried and ground through a 2 mm screen. Samples of the three fractions and whole corn stover with and without NaOH pretreatment were subjected to enzymatic hydrolysis in order to determine the effect of fractionation on glucose production. The average amounts of glucose released after 60 h of hydrolysis from pretreated cobs, leaves and husks, stalks, and whole stover were 0.50, 0.36, 0.28, and 0.36 g/g dry biomass, respectively. The average amounts of glucose released after 60 h of hydrolysis from nonpretreated cobs, leaves …

Using Covers To Minimize Odor And Gas Emissions From Manure Storages, José R. Bicudo, David R. Schmidt, Larry D. Jacobson

Agricultural Engineering Extension Publications

Odor emissions from animal production sites are typically the leading cause of nuisance complaints. Locating facilities far from neighbors is often a solution to the odor problem, but this is not always an option for producers. Most often, reducing odor emissions from the farm is the only option available.

Statistical Procedures For Evaluating Daily And Monthly Hydrologic Model Predictions, Marilyn E. Coffey, Stephen R. Workman, Joseph L. Taraba, Alex W. Fogle

Biosystems and Agricultural Engineering Faculty Publications

The overall study objective was to evaluate the applicability of different qualitative and quantitative methods for comparing daily and monthly SWAT computer model hydrologic streamflow predictions to observed data, and to recommend statistical methods for use in future model evaluations. Statistical methods were tested using daily streamflows and monthly equivalent runoff depths. The statistical techniques included linear regression, Nash-Sutcliffe efficiency, nonparametric tests, t-test, objective functions, autocorrelation, and cross-correlation. None of the methods specifically applied to the non-normal distribution and dependence between data points for the daily predicted and observed data. Of the tested methods, median objective functions, sign test, autocorrelation, …

Assessing The Benefits Of Misting-Cooling Systems For Growing-Finishing Swine In Kentucky As Affected By Environment And Pig Placement Date, Thomas C. Bridges, R. S. Gates, Douglas G. Overhults, Larry W. Turner

Agricultural Engineering Extension Publications

The growth performance of animals is often affected by extreme environmental conditions. In the case of swine, generally a cold environment will increase feed intake as the pig strives to maintain body temperature, while warmer environments may reduce growth, increase body maintenance demands, and subject the animal to environmental stress. Confinement houses are widely used as a primary means of modifying the environment to improve conditions for the growth of swine. Environment in these structures is usually controlled by natural or mechanical ventilation and by insulation for cold climates and limited use of evaporative cooling for summertime conditions.

Temperature Control Of A Solid Substrate Cultivation Deep - Bed Reactor Using An Internal Heat Exchanger, Mari S. Chinn, Sue E. Nokes

Biosystems and Agricultural Engineering Faculty Publications

The solid substrate cultivation (SSC) process is often limited by rapid increases in temperature as a result of metabolic activity and poor heat transfer properties of the solid substrate. High temperatures can adversely affect microbial growth and product formation. Reduction of substrate temperatures is important for improved productivity, yet effective and efficient control of heat transfer in a deep-bed SSC reactor has proven difficult. An internal cooling water coil was incorporated into a deep-bed reactor system and evaluated for its ability to reduce substrate temperature. Three operating treatments were investigated: cooling water circulation whenever the center bed temperature was above …

Evaluation Of Foam Fractionation Column Scale-Up For Recovering Bovine Serum Albumin, Czarena L. Crofcheck, Kelly Gillette

Biosystems and Agricultural Engineering Faculty Publications

Foam fractionation is an adsorptive-bubble separation method that, according to researchers, is a feasible technique for the separation and/or concentration of proteins. The foam fractionation of bovine serum albumin (BSA) in laboratory-scale foam fractionation columns (750 and 1250 mL) and the relationship between the two laboratory-scale columns and a pilot-scale column (5000 mL) were investigated. Recovery, enrichment, and performance factor values were experimentally determined with three different column volumes with varying pore sizes, gas superficial velocities, and, in the case of the 750 mL column, foam column height. As the pore size decreased, the amount of protein recovered from the …

Simulation Of Fixed– And Variable–Rate Application Of Granular Materials, John Patrick Fulton, Scott A. Shearer, Timothy S. Stombaugh, Michael E. Anderson, Thomas F. Burks, Stephen F. Higgins

Biosystems and Agricultural Engineering Faculty Publications

Research has shown that application errors exist with variable–rate technology (VRT) systems. Consequently, using prescription maps for economic and agronomic analyses can generate misleading results. The intent of this article was to develop and validate a spatial data model for generating “as–applied” maps to support the advancement of precision agriculture practices. Previous research modified ASAE Standard S341.2 to include a 2–D matrix of collection pans to assess fixed–rate and variable–rate (VR) deposition of granular fertilizers and agricultural lime from a spinner disc spreader. The “as–applied” spatial data model uses GIS functionality to generate “as–applied” surfaces by merging distribution patterns and …