Biomedical Engineering and Bioengineering Commons^™

Knee Angles After Crosstalk Correction With Principal Component Analysis In Gait And Cycling, Jordan Skaro, Scott J. Hazelwood, Stephen M. Klisch

Biomedical Engineering

Principal component analysis (PCA) has been used as a post-hoc method for reducing knee crosstalk errors during gait analysis. PCA minimizes correlations between flexion–extension (FE), abduction–adduction (AA), and internal–external rotation (IE) angles. However, previous studies have not considered PCA for exercises involving knee flexion angles that are greater than those typically experienced during gait. Thus, the goal of this study was to investigate using PCA to correct for crosstalk during one exercise (i.e., cycling) that involves relatively high flexion angles. Fifteen participants were tested in gait and cycling using a motion analysis system. Uncorrected FE, AA and IE angles were …

Computational Bone Mechanics Modeling With Frequency Dependent Rheological Properties And Crosslinking, Timothy G. Moreno

Master's Theses

Bone is a largely bipartite viscoelastic composite. Its mechanical behavior is determined by strain rate and the relative proportions of its principal constituent elements, hydroxyapatite and collagen, but is also largely dictated by their geometry and topology. Collagen fibrils include many segments of tropocollagen in staggered, parallel sequences. The physical staggering of this tropocollagen allows for gaps known as hole-zones, which serve as nucleation points for apatite mineral. The distance between adjacent repeat units of tropocollagen is known as D-Spacing and can be measured by Atomic Force Microscopy (AFM). This D-Spacing can vary in length slightly within a bundle, but …

The Tierni Resistance Training System, Michael J. Hansen, Abigail M. Youngblood, Gabriel M. Johnson

Biomedical Engineering

The purpose of the Tierni Resistance Training System project was to design and construct functional workout apparel that has built-in resistance. For this product, the key customer requirements we set out to address were most importantly material comfort and functionality, followed by stylishness, lack of latex, safety for injured and uninjured users, and washer safety. To meet these customer requirements, we started by researching current resistance training technology, and used the findings as a springboard for our own design development. After initial brainstorming, engineering specifications were generated based on the customer requirements. These specifications revolved around the thermal insulation, pressure, …

Studying The Efficacy Of An Injectable 3-Dimensional Fibrin Extracellular Matrix To Characterize The Effects Of Antitumor Agents On Sw620 Cells In A Microfluidic Device, Thèo Anastos

Master's Theses

Colorectal cancer is the third most common cancer in the United States and there is currently a lot of research going into new antitumor agents to kill the cancer. One method for replicating the tumor response to a drug in vivo is by creating an in vitro drug testing model to replicate the in vivo condition. This research project was conducted to determine the efficacy of testing tumor cultures in a microfluidic device as a way to provide accurate drug responses in vitro instead of using in vivo subjects in clinical trials. A total of four experiments were conducted with …

Electro-Muscle-To-Muscle Transfer, Hailey Quinn Casino, Jake Keola Javier, Samuel Joseph Borda, Charlotte Amalie Anderson

Biomedical Engineering

The Electro Muscle to Muscle Transfer (EMMT) system will entail designing, manufacturing, and providing a wearable device that stimulates paralyzed muscles in the hand by sampling and amplifying muscles from the forearm. With further development, the system may be capable of using different muscle inputs other than the forearm muscles along with different stimulated muscle outputs other than the hand. The system functions as a rehabilitative device for spinal cord injuries, irreparable nerve loss and/or damage, and improper neuromuscular function. It is not for total treatment nor for curing of the disabilities listed above but to alleviate the side effects …

Development Of A Robust Methodology To Obtain And Assess Myogenic Precursor Cells For Their Use In Regenerative Therapies, Ricardo Lasa

Master's Theses

Peripheral arterial occlusive disease (PAOD) is characterized by buildup of atherosclerotic plaque in peripheral arteries that leads to an occlusion that can interrupt the supply of blood to the peripheral tissue, causing downstream tissue ischemia/hypoxia. PAOD is estimated to affect over 200 million patients worldwide. Current surgical revascularization treatments can be effective in about half of the patient population, leading to a significant number of patients with no treatment options beyond pharmacological intervention and lifestyle modification. The decrease in blood flow downstream of the occlusion leads to increased blood pressure gradient in the microvasculature, specifically in vessels that connect arterial …

Adaptive Laboratory Evolution Of Scenedesmus Obliquus For Increased Carbohydrate Content And Biomass Productivity, Nahel Ali

Master's Theses

The economics of microalgal bioproduct commercialization would benefit from increased accumulation of energy storage compounds, such as carbohydrates and lipids, and increased biomass productivity. This thesis explores two adaptive laboratory evolution strategies for improving Scenedesmus obliquus: single UV-mutagenesis and low light cultivation at a high dilution rate to produce cultigens with greater carbohydrate content and iterative UV-mutagenesis and selection under outdoor conditions in a raceway pond at a high dilution rate to increase biomass productivity.

Two cultigens were generated with the goal of increased carbohydrate content: K5 and K7. Both were mutagenized for 5 seconds and cultivated in 50-mL …

The Effect Of Focused Ultrasound On Altering The Diameter Class Of Nerve Fibers Contributing To A Compound Evoked Potential, Analyzed Using A Perturbative Decomposition Technique., Megan Wurden

Master's Theses

Peripheral neuropathies are disorders that involve the damage of peripheral nerve fibers, affecting the ability of different parts of the body to communicate. A differentiating factor in diagnosis between various clinical conditions can be which size class of nerve fibers are affected. A nerve conduction velocity test can be used to assess the viability of the nerve but is a single-parameter test and gives no information about the population characteristics of the remaining active fibers. A method developed and previously reported by Szlavik (2016) utilizes a mathematical perturbed decomposition to determine the normalized frequency of each size class of fiber …

Gyroscopic Human Balance Device, Randy Lam Hau, Spencer Ross, Yael Farkash

Biomedical Engineering

This project’s sponsor, Charlie Guitierrez, has decades of experience building assistive walking devices for the wheelchair bound population. During his work, he noticed that many of his clients retained some ability to balance themselves and so theorized that they would be able to walk independently if given some form of assistance. This assistance could potentially be in the form of a wearable gyroscope. Gyroscopes are commonly used to stabilize objects subjected to instability, such as bicycles, motorcycles, and ships. Thus, a wearable gyroscope would assist its user in maintaining overall stability by imparting reactive torques and forces if the user …

Hypoxic Incubation Chamber, Makenzie Jones, Andrea Skattenborg, Henry Elsner

Biomedical Engineering

In developing a model to test anti-tumor drugs, Dr. Christopher Heylman’s lab requires the ability to culture cells in a hypoxic environment. The purpose of this project was to make this possible. Funding for this project comes from the Biomedical Engineering Department, the Hannah-Forbes Fund, and Dr. Heylman’s lab. The chamber must be able to reach a user-defined oxygen concentration and hold that concentration for 48 hours while creating an environment conducive to cell culture. Importantly, the chamber must also be sterilizable and cleanable for repeated use. While several products exist to create hypoxic environments for cell culture, they are …

A Novel Method To Commercialize Medical Devices Initially Developed At California Polytechnic State University San Luis Obispo, Christina Grigorian

Master's Theses

California Polytechnic State University, San Luis Obispo is a university that encourages students to approach learning hands-on. As such, there is cutting-edge technology being developed by students in all departments on campus. Being that the university possesses an outstanding biomedical engineering department, there are groundbreaking medical devices that students are creating at Cal Poly SLO. These are devices that can better the lives of individuals suffering from ailments or fulfill needs in the medical industry. Subsequently, it is vital that these devices make it out of campus laboratories and into the hands of consumers. In order to move a product …

Understanding The Effects Of Long-Duration Spaceflight On Fracture Risk In The Human Femur Using Finite Element Analysis, Keyanna Brielle Henderson

Master's Theses

Long-duration spaceflight has been shown to have significant, lasting effects on the bone strength of astronauts and to contribute to age-related complications later in life. The microgravity environment of space causes a decrease in daily mechanical loading, which signals a state of disuse to bone cells. This affects the bone remodeling process, which is responsible for maintaining bone mass, causing an increase in damage and a decrease in density. This leads to bone fragility and decreases overall strength, posing a risk for fracture. However, there is little information pertaining to the timeline of bone loss and subsequent fracture risk.

This …

Smart Motor Syringe System, Conard Chan, Jenny Chiao

Electrical Engineering

Syringe pumps are widely used in many research applications especially in the applications that need precise control. Today most medical research utilizes syringes to control the fluid being pumped to the experiment objects. In most cases microscopic or nano-scopic motion control is required to acquire optimal results, such application includes purification of DNA/RNA from contaminants[1]. The high precision required to control the syringe pump makes it difficult to perform manually. This paper focuses on the design of an intelligent syringe pump motor control system to achieve reliable and precise control for biomedical experiments. This project improves medical research quality with …

Analysis Of Electroanatomic Mapping System Accuracy Using X-Ray Reconstruction Of Electrode Locations In A Porcine Animal Model, Hana Boudlali

Master's Theses

Fluoroscopy is considered the gold standard for locating catheters during cardiac electrophysiology (EP) procedures. However, fluoroscopy emits ionizing radiation which can lead to adverse health effects when exposed to in high doses (World Health Organization, 2016). Electroanatomic mapping (EAM) systems display the three-dimensional location of EP catheters and measure the local electrical activity of the heart. They can minimize a physician’s reliance on fluoroscopy and can help reduce radiation exposure during a case (Casella, 2011).

EAM systems are diagnostic medical devices that inform the placement of ablation therapy and must accurately locate catheters to be deemed safe. Test methods to …

A Protocol For Achieving Adherent Cell Culture Within A Microfluidic Device, Tarra Danielle Sanders

Master's Theses

The goal of this study is to design a protocol for the adherent cell culture within a novel microfluidic device. Microscale cell culture protocols were developed for loading cells using poly-L-lysine to enhance adherent cell culture of murine derived NIH 3T3 fibroblasts. This work sought to develop a method for adherent microculture by examining various sterilization, surface treatment, and seeding techniques. Using a vacuum suction loading technique, air plasma treatment and a poly-L-lysine surface treatment adherent cell culture was observed within the device. The work presented here is part of a collaborative effort that aims to develop protocols for the …

Finite Element Analysis Of Total Knee Arthroplasty, Sean Yueh

Master's Theses

The total knee arthroplasty (TKA) has become one of the most successful procedures in all of medicine, with an average of over 966,000 operations performed a year. Since its introduction in 1968, the TKA’s surgical process and implant designs have continuously been improved to increase survivability. However, the need for a revision TKA – due to aseptic loosening – continues to be a problematic aspect of the procedure. Stress shielding induced by different design parameters of the implant has generated controversy in the determination of an ideal configuration. The purpose of this study is to investigate how implant design parameters …

Effects Of Marathon Training On Male And Female Femoral Stress Fracture Risk, Clara Lin

Master's Theses

Marathon runners are prone to femoral stress fractures due to the high magnitudes and frequencies of lower extremity loads during training. Female runners tend to have a greater incidence of stress fracture compared to male runners. Sex-specific differences in body structure, joint pressure, and muscle activation patterns that influence bone remodeling may cause this observed difference in stress fracture occurrence. The goal of this thesis was to develop a finite element model of the femur during marathon training, then determine if marathon training affected bone properties of male and female runners differently. To achieve this goal, a finite element femur …

Optimal Parameter Values For Accurate And Repeatable Nanoindentation Of Human Trabecular Bone, Stephen Matthew Kmak

Master's Theses

Nanoindentation techniques have not been standardized for use on bone tissues, making comparison of bone material properties obtained via nanoindentation across studies difficult and unreliable. This study determined a set of optimal parameter values for thermal drift correction time, dwell time, and loading rate that can be used to obtain accurate and repeatable material properties from human femoral trabecular bone through experimentation and statistical analysis. All testing was conducted using a single nanoindenter on a single trabeculae, with the assumption that material properties within the individual trabeculae were internally consistent. Parameters not of interest during this study, such as ambient …

Development And Optimization Of Imaging And Image Quantification Techniques For Tissue-Engineered Blood Vessel Mimics, Ashley Turcott

Master's Theses

Blood vessels mimics (BVMs) are tissue-engineered blood vessels used to test vascular devices in an environment that mimics some simple anatomical factors of native blood vessels. It is important to accurately and consistently assess tissue-engineered blood vessels, although there is currently a lack of standardization in Cal Poly’s Tissue Engineering Lab and in the entirety of the field. The goal of this thesis was to develop and optimize imaging and image quantification techniques for tissue-engineered blood vessels.

The first aim of this thesis optimized and compared imaging and assessment techniques for electrospun scaffolds. Images from different SEMs were compared to …

Smartphone-Tape Method For Calculating Body Segment Inertial Parameters For Analysis Of Pitching Arm Kinetics, Jay Sterner

Master's Theses

The objectives of this study were to (1) develop a non-invasive method (referred to as Smart Photo-Tape) to calculate participant-specific upper arm, forearm, and hand segment inertial properties (SIPs) (e.g. mass, center of mass, and radii of gyration) and (2) use those Smart Photo-Tape properties in inverse dynamics (ID) analyses to calculate injury-related pitching arm kinetics. Five 20- to 23- year-old baseball pitchers were photographed holding a baseball and analyzed using the Smart Photo-Tape method to obtain 3-D inertial properties for their upper arm, forearm, and hand. The upper arm and forearm segments were modelled as stacked elliptic cylinders and …

Investigation Of Experimental Variation Of Bovine Sphingomyelin As A Novel Ingredient For Ultraviolet Protection, Esther Chen

Master's Theses

Skin cancer is a prevalent disease that globally affects 2-3 million people per year [1]. This number is expected to grow tenfold as depletion of the ozone layer contributes to harsher rays reaching Earth’s surface [2]. A common way to protect against those ultraviolet waves is to apply sunscreen, however, recent reports call into question the safety of some active ingredients as they can enter through the skin into the bloodstream [3]. This thesis aims to investigate an alternative solution that uses bovine sphingomyelin (BSM) as photoprotective solution against UV irradiation.

In order to evaluate the effectiveness of BSM against …

The Effect Of Distal Core Flattening And Heat Treatment On 304 Stainless Steel Guide Wires, Andrew Spencer Yap, Bryce Eric Veit, Matthew Frederick Lopez Villena

Materials Engineering

The mechanical response of 304 stainless steel guide wires due to different temper conditions and amounts of flattening is to be explored in this project. For this specific project, there is no public literature on the mechanical properties of guide wires with the above conditions through tensile testing or Turns to Failure Testing. To address this, the project with Abbott Vascular will measure the mechanical properties of guide wires using the aforementioned factors. Due to a lack of previous literature on this research topic, there are no quantitative goals for the project, however, any new research compiled in this area …

Reading Robot, Gillian Watts, Andrew Myers, Sabrinna Tan, Taylor Klein, Omeed Djassemi

General Engineering

Presently, there is an insufficient availability of human experts to assist students in reading competency and comprehension. Our team’s goal was to create an improved socially assistive robot for use by therapists, teachers, and parents to help children and adults develop reading skills while they do not have access to specialists. HAPI is a socially assistive robot that we created with the goal of helping students practice their reading comprehension skills. HAPI enables a student to improve their reading skills without an educator present, while enabling educators to review the student's performance remotely. Design constraints included: physical size, weight, duration …

Prosthetic Foot Shell, Ql+, Kathryn Victoria Versteeg, Jackson A. Tucker, Ethan William Frey

Mechanical Engineering

This final design review includes an overview of our project and the steps we have taken to create our final product. We discuss the background research conducted, including various products like the foot shell we are trying to design and its related patents, along with similar past senior projects. As our product is considered a medical device, there are also certain standards that we must comply with. After determining our problem statement, we established what we believe to be the wants and needs of our user. These wants and needs were converted into specifications for our design, with durability as …

Alternative Epinephrine Auto-Injector, Joshua Wong, Uriel Nieves-Cruz, Tara Howard

Biomedical Engineering

Project: Alternative Epinephrine Injector started as a solution for Bianca Aleman’s little brother however the scope has evolved to include the many millions of individuals across the world who struggle with a life-threatening allergen. The stakeholders of this project are Cal Poly and Dr. Michael D. Whitt. Our goals are the following:

● Develop a foolproof method of injection that consistently delivers a dosage of epinephrine

● Be equal or less than the current size of an EpiPen (6 in)

● Be easy to transport or store when not-in-use

● Create an isolated environment where the epinephrine will not be …

Virtual Stethoscope - Otoscope, Ermen J. Elenes-Cazares, Ceasar A. Hurtado, Thomas M. Margolle

Biomedical Engineering

The purpose of this report was to develop a working prototype for a virtual stethoscope and otoscope. Sponsored by Courtney Farr, the virtual diagnostic care system – HouseCalls Mobile digital stethoscope/otoscope is meant for use by medical professionals and non – medical professionals for preliminary medical exams while physically not in a medical setting. The HouseCalls Mobile device is to characterize key biometric parameters such as breathing patterns, heart irregularities, and visual clinical evaluation of the inner ear. This device is intended for pediatric use.

Tmtt Chimera Valve Attachment Process, Paulina Nguyen, Devin Debouk, Tamar Kazazian, Noah Thompson

Biomedical Engineering

No abstract provided.

Non-Invasive Peripheral Venous And Arterial Line Air Detector For Embolization Prevention, Alexandria Kwong, Kevin Shu, Dylan Meinster

Biomedical Engineering

The scope of this project includes designing a non-invasive bubble detector for peripheral venous and arterial lines. For minimally invasive cardiac procedures, arterial and venous access is necessary for these procedures as is constant flow through the tubing to prevent clotting and to administer drugs. Air bubbles are common in these lines and can be consequential if enough air is introduced into the human system. Air embolisms are the most common and relevant issues during these procedures. The goal of this device is to create an attachable detector for air bubbles in saline that can also terminate flow and alert …

Surf Sled, Marius Jatulis, Arthur Zaayer, Griffin O'Malley, Jose Covarrubias

Mechanical Engineering

This Final Design Review document outlines the process by which we designed and built a surfboard sled, nicknamed the “Beachin’ Buggy”, for the AmpSurf program. The document describes the goals and services that AmpSurf provides for those living with disabilities, and the current methods that volunteers use to transport people from to beach to the water and onto a surfboard. It then identifies the need for a new system for beach-to-water transportation, along with all specifications, constraints, and goals for the system. Background research will be introduced to relate similar products to this project, and their relevant features and parameters …

Concussion Detection Device, Jenna C. Sussex, Mark B. Edin, Bianca X. Aleman

Biomedical Engineering

No abstract provided.