Structures and Materials Commons^™

A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye

Mechanical Engineering Undergraduate Honors Theses

The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Effects Of Tempering Temperature On Gas Turbine Fan Cases, Seth Utter

Honors Scholar Theses

The project aimed to investigate the effects of tempering temperature on metals used for gas turbine engine fan cases as a major relevant concern is containing blades in during blade-out events. There are three ways to accomplish this: using a thicker metal, incorporating different materials into the case, or heat treating the metal. This project focused on the third solution: reviewing the impact toughness and hardness of fractured samples and their equivalent ductile-to-brittle transition shear faces. Given its availability, 1045 steel, as opposed to aerospace grade metals, was used for in-house testing. The data obtained from these experiments were then …

Jcati Carbon Fiber Recycler: Crusher System, Devin Riley

All Undergraduate Projects

With a substantial rise in Carbon Fiber use across all industries, the need for a way to recycle the waste has grown as well. A group of Mechanical Engineering Technology students at Central Washington University funded by the Joint Center for Aerospace Technology (JCATI) have created a machine to recycle waste wing trimmings from the Boeing company’s airplanes. This machine consists of 5 different sub-assemblies being the oven, crusher, gear train, conveyor, and shredder. The purpose of this project was to decrease the deflection in the crusher caused by bulging in the housing and movement of the bearings. To decrease …

Exploring Additive Manufacturing In A Space Environment - A Capstone Design Project Experience, Zain Zafar Khan, Zachary Alan Sobelman, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

The employment of additive manufacturing in the non-standard environments like space, ships, or submarines has the potential to be an advanced utility not only in the pre-flight production of aerospace components and structures, but also for the onboard manufacturing of components and tools necessary for future space missions. For example, the ability to produce tools and structural components on the International Space Station can provide the space community the opportunity to make repairs and upgrades to the space station without wasting time and resources transporting such materials through additional missions. Additive manufacturing would allow for space missions to use on …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

Molecular Dynamics Modeling Of Polymers For Aerospace Composites, Swapnil Sambhaji Bamane

Dissertations, Master's Theses and Master's Reports

Polymer matrix composite materials are widely used as structural materials in aerospace and aeronautical vehicles. Resin/reinforcement wetting and the effect of polymerization on the thermo-mechanical properties of the resin are key parameters in the manufacturing of aerospace composite materials. Determining the contact angle between combinations of liquid resin and reinforcement surfaces is a common method for quantifying wettability. It is challenging to determine contact angle values experimentally of high-performance resins on CNT materials such as CNT, graphene, bundles or yarns, and BNNT surfaces. It is also experimentally difficult to determine the effect of polymerization reaction on material properties of a …

Noise Reduction Techniques In Commercial Aircraft Cabins, Hashem Hashem

Student Works

Main sources of noise heard inside an aircraft cabin:

• Engines
• Airframe & control surfaces
• Window vibrations
• Passenger announcements & activities.

Energy Dissipation In A Sand Damper Under Cyclic Loading, Ehab Sabi

Civil and Environmental Engineering Theses and Dissertations

Various seismic and wind engineering designs and retrofit strategies have been in development to meet structures' proper and safe operation during earthquake and wind excitation. One such method is the addition of fluid and particle dampers, such as sand dampers, in an effort to reduce excessive and dangerous displacements of structures. The present study implements the discrete element method (DEM) to assess the performance of a pressurized sand damper (PSD) and characterize the dissipated energy under cyclic loading. The idea of a PSD is to exploit the increase in shearing resistance of sand under external pressure and the associated ability …

Structural Sizing Of Post-Buckled Thermally Stressed Stiffened Panels, Walid Arsalane

Theses and Dissertations

Design of thermoelastic structures can be highly counterintuitive due to design-dependent loading and impact of geometric nonlinearity on the structural response. Thermal loading generates in-plane stresses in a restrained panel, but the presence of geometric nonlinearity creates an extension-bending coupling that results in considerable transverse displacement and variation in stiffness characteristics, and these affects are enhanced in post-bucking regimes. Herein a methodology for structural sizing of thermally stressed post-buckled stiffened panels is proposed and applied for optimization of the blade and hat stiffeners using a gradient-based optimizer. The stiffened panels are subjected to uniform thermal loading and optimized for minimum …

Novel Thermal Coating For High-Speed Airplanes, Abinash Satapathy, Lakshay Battu, Liam Watson, Nazanin Rajabi

Symposium of Student Scholars

In comparison to various other materials, Carbon Fiber, specifically Carbon Fiber Reinforced Polymers (CFRP), is pre-eminent amongst other materials for use on aeronautical systems. Due to its high specific strength (strength-to-weight ratio), CFRP is prominent for carrying heavy loads while maintaining a lightweight build. However, when influenced by heat resulting from air resistance, CFRP is known to undergo serious degradation that would significantly decrease the effectiveness of the polymers. To prevent this degradation and maintain the strength of the CFRP, thermal protective layers (TPLs) are designed to shield the CFRP from heat exposure. This research is focused on the examination …

Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen

Theses and Dissertations

Additively manufactured tungsten was printed in pure nitrogen, nitrogen-2.5% hydrogen, and nitrogen-5% hydrogen atmospheres as part of a 2^3 full factorial designed experiment and subjected to room temperature and high-temperature three-point-bend testing, chemical analysis, hardness testing, and microstructural imaging techniques. The pure nitrogen specimens exhibited the highest strength and ductility at both high temperature and room temperature. Chemical analysis showed a 2-8x reduction in compositional oxygen relative to unprocessed powder. Hardness values for all samples was between 306.8 and 361.5 HV1. It is proposed that adding hydrogen into the build atmosphere reduced the available energy density for tungsten melting by …

Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya

Theses and Dissertations

The process of creating metal components through additive manufacturing is changing the way different industries can avoid the shortcomings of traditional metal production. Metals such as tungsten, molybdenum, and rhenium have many advantages for different applications, especially when alloyed together. In this study, an additively manufactured alloy containing 70% molybdenum, 25% tungsten, and 5% rhenium (70Mo-25W-5Re) is tested for its strength, ductility, hardness, and porosity. The 70Mo-25W-5Re alloy is printed through Laser Powder Bed Fusion (LPBF) under different conditions such as printing speed and printing atmosphere. Additionally, the effects of post printing heat treatment are conducted to understand the advantages …

Carbon Fiber Recycling: Delamination System, Aaron Eastman

All Undergraduate Projects

The production of composite wings at Boeing causes carbon fiber waste and CWU Mechanical Engineering Technology students have been tasked in designing a carbon fiber recycling system. This project was brought forth and funded by the Joint Center for Aerospace Technology Innovation (JCATI). There are three subsystems that make up the carbon fiber recycling system, the delamination system, shredding system, and the oven. The purpose of this project was to increase the efficiency and effectiveness of the delamination system of the carbon fiber recycling system. The old system reached approximately 30-40 percent delamination with one pass through the system, and …

Jcati Carbon Fiber Shredder 2022, Parker Sudderth

All Undergraduate Projects

This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

Design, Development, And Testing Of Near-Optimal Satellite Attitude Control Strategies, Giovanni Lavezzi

Electronic Theses and Dissertations

Advances in space technology and interest toward remote sensing mission have grown in the recent years, requiring the attitude control subsystems of observation satellites to increase their performances in terms of pointing accuracy and on-board implementability. Moreover, an increased interest in small satellite missions and the recent technological developments related to the CubeSats standard have drastically reduced the cost of producing and flying a satellite mission. In this context, the proposed research aims to improve the state of the art for satellite attitude control methodologies by proposing a near-optimal attitude control strategy, simulated in a high-fidelity environment. Two strategies are …

Microscale Transverse Compression Modeling: A Comparative Study Of The Analytical Mac/Gmc Methods To Experimental Results, Emily Zeitunian

Dissertations, Master's Theses and Master's Reports

Composite materials require a multi-scale approach to fully understand its behavior. At the micro level, material behavior analysis is conducted most often using numerical or analytical approaches. These models, however, require validation from experimental data to ensure material predictions are accurate. This study compares a semi-analytical micromechanical analysis tool, MAC/GMC, to experimental results of in-situ microscale transverse compression testing conducted at AFRL facilities. Effective properties, stress-strain curves, stress and strain fields, and damage predictions are compared with experimental outputs. Both generalized method of cells (GMC) and high-fidelity generalized method of cells (HFGMC) theories implemented within MAC/GMC show results that agree …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

Mechanical Interfacial Locking And Multiscale Modeling Of Reinforced Thermoplastic Composites For Structural Applications, Anmol Kothari

All Dissertations

The ever-growing pressure of reducing the adverse impact of transportation systems on environment has pushed industries towards fuel-efficient and sustainable solutions. While several approaches have been used to improve fuel efficiency, the light-weighting of structural components has proven broadly effective. In this regard, reinforced thermoplastic composites (RTPC), owing to their high recyclability, higher impact strength and fast cycle times, have become competitive candidates at an industrial scale. However, to implement RTPC toward large scale structural applications several challenges pertaining to material design and manufacturing effects need to be addressed. To this end, a computational study is carried out to address …

Fatigue Damage Quantification And Life Estimation With Provision For Microstructure, Arash Pourbagheri Jirandehi

LSU Doctoral Dissertations

This dissertation provides methodologies for the quantification of different forms of fatigue damage by considering the role of microstructure. The laws of thermodynamics in conjunction with Finite Element Method (FEM) are utilized to devise thermodynamically-base frameworks for the estimation of cyclic damage in polycrystalline metals. Accordingly, a microstructure-sensitive platform for fatigue life estimation is introduced. The proposed framework is assessed for 3D printed metallic alloys at room and elevated temperatures. Further, it is used to analyze the fatigue performance difference between additively manufactured Inconel 718 in three print orientations. This research is of fundamental vital interest because it ensures that …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Fluid-Structure Interaction Of Nrel 5-Mw Wind Turbine, Mohamed Sayed Elkady Abd-Elhay

Theses and Dissertations

Wind energy is considered one of the major sources of renewable energy. Nowadays, wind turbine blades could exceed 100 m to maximize the generated power and minimize produced energy cost. Due to the enormous size of the wind turbines, the blades are subjected to failure by aerodynamics loads or instability issues. Also, the gravitational and centrifugal loads affect the wind turbine design because of the huge mass of the blades. Accordingly, wind turbine simulation became efficient in blade design to reduce the cost of its manufacturing. The fluid-structure interaction (FSI) is considered an effective way to study the turbine's behavior …

Space Suit Attachment Quick Release System, Elyse C. Gillis-Smith, Andres I. Elzaurdia, Cole H. Stanton, Michael T. Roth

Mechanical Engineering

NASA plans to make it back to the Moon by 2024 with their Artemis Program, and stay there for a longer period of time to conduct research which will support the future of space exploration. While on the lunar surface, astronauts need to maximize their efficiency by carrying tools on their Exploration Extravehicular Mobility Unit (xEMU), and to accommodate this need, the Extravehicular Activity (EVA) Tools Team is pursuing a utility belt concept. The objective of this project is to develop a system capable of interfacing between the utility belt and any given tool, while also accommodating numerous restrictions and …

Prediction Of In-Plane Stiffnesses And Thermomechanical Stresses In Cylindrical Composite Cross-Sections, Bryson M. Chan

Master's Theses

Accurate mechanical analysis of composite structures is necessary for the prediction of laminate behavior. Cylindrical composite tubes are a mainstay in many structural applications. The fundamental design of circular composite cross-sections necessitates the development of a comprehensive composite lamination theory. A new analytical method is developed to characterize the behavior of thin-walled composite cylindrical tubes using a modified plate theory. A generated numerical solver can predict properties such as axial stiffness, bending stiffness, layer stresses, and layer strains in composite tubes subjected to combined mechanical loading and thermal effects. The model accounts for the curvature by transforming and translating the …

Characterizing High Entropy Alloys For Hypersonic Applications, Katherine Pettus

Mechanical Engineering Undergraduate Honors Theses

In this paper, the properties of a new and broad class of materials, high entropy alloys (HEAs), were investigated and evaluated for hypersonic applications. The plan was to identify candidate hypersonic HEAs and model the high-temperature strength using new advanced material models that account for asymmetry and anisotropy characterized with available test data. After accessing a local database of HEAs and their material properties in collaboration with Dr. Gorsse et al., it was realized the knowledge of HEAs is currently very broad but lacks depth. While hundreds of HEAs have been created and tested, none so far have both sufficient …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Numerical Reconstruction Of Spalled Particle Trajectories In An Arc-Jet Environment, Raghava S. C. Davuluri, Sean C. C. Bailey, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

To evaluate the effects of spallation on ablative material, it is necessary to evaluate the mass loss. To do so, a Lagrangian particle trajectory code is used to reconstruct trajectories that match the experimental data for all kinematic parameters. The results from spallation experiments conducted at the NASA HYMETS facility over a wedge sample were used. A data-driven adaptive methodology was used to adapts the ejection parameters until the numerical trajectory matches the experimental data. The preliminary reconstruction results show that the size of the particles seemed to be correlated with the location of the ejection event. The size of …