Structures and Materials Commons^™

Novel Design And Fabrication Of A High-Speed Transient Heat Flux Sensor For Application To Rotating Detonation Engines, Zachary Todd Tallman

Graduate Theses, Dissertations, and Problem Reports (ETD)

Rotating detonation engine (RDE) combustion systems have been a topic of interest in the pressure gain combustion community for their benefits over traditional gas turbine engine combustors. However, cooling requirements for these engines are significantly higher and less predictable than those of non-detonating engines. To understand and quantify the high-speed heat transfer dynamics within an RDE, a novel high-frequency heat flux sensor is presented. This study aims to design a robust, single-sided sensor that can withstand the high temperature and harsh environment of an RDE for extended durations. Screen printing is used to deposit a layered, platinum-yttria-stabilized zirconia (YSZ) film …

Ground Testing Of A Magnetic-Electrostatic Separation System For Lunar Regolith Beneficiation, Peter Bachle, Charles Wood, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The separation of lunar regolith by mineral composition and size category is useful forin-situ resource utilization (ISRU). The research presented herein discusses the designing and development of equipment that has the potential to separate lunar regolith into aluminum, iron-titanium, and magnesium-iron ores. Along with the metal ore separation, this equipment shows the potential to separate regolith by size categories. The combined effect of these separation methods generates output that is valuable to subsequent use in metal and oxygen extraction, additive manufacturing, and regolith sintering processes. The designed equipment uses a dual-strength magnet system with N42 and N52 neodymium magnets for …

Smart Material Actuated Flap, James Lyons, Kristofer Johnson

Williams Honors College, Honors Research Projects

The objective of this project is to develop and evaluate a smart material actuated aerodynamic control surface to determine the viability of these new systems as alternatives to conventional electromechanical and hydraulic systems. The research will begin with the selection of a control surface and actuator design. The concept will then be tailored to create an experimental model for the purposes of this project. Smart materials that suit the model requirements will be selected and procured. Next, the actuators will be shape trained and characterized to meet the model requirements. Then, a benchtop model will be produced for design verification, …

Additive Manufacturing Of Multifunctional Materials And Composites, John Michael Pappas

Doctoral Dissertations

"This research focused on developing fundamental knowledge of process-material interactions for additive manufacturing of multifunctional materials that are highly desirable in high-tech industries for potential weight and space savings. Multifunctional materials are very sensitive to defects, which severely hinder performance. Thus, defect formation was systematically studied to develop strategies and methodologies to efficiently fabricate high-performance materials and composites. Blown-powder-based laser additive manufacturing of transparent spinel ceramics was investigated to reduce porosity and cracking, defects that hindered transparency and mechanical properties. A systematic study of processing parameters revealed that laser power and powder flow rate had the largest effects on defect …

Gas-Generating Reactive Materials: Design, Evaluation And Effect Of Morphology On Their Ignition And Combustion, Purvam Mehulkumar Gandhi

Dissertations

This work investigates optimizing gas-generating reactive materials, focusing on particle morphology's effect on ignition and combustion behavior. Metal-based gas-generating energetic materials (EMs) are promising alternatives to replace traditional CHNO compounds. Design of advanced metal-based EMs requires consistent ways of evaluating how their characteristics affect their ignition and combustion. Many relevant evaluation approaches exist; however, the results may be difficult to compare directly across different studies. Commonly, experimentalists ignite metal-based EMs in enclosed chambers and report pressures, P. However, direct comparison of these pressures is hindered by variations in the chamber volume, V, and the EM mass, m. To standardize the …

Kinetic Modeling Of Dust Grain Dynamics In Electrostatic Sieving, Aaron Berkhoff, Easton Ingram, Fateme Rezaei, Jeffrey Smith, David Bayless, William Schonberg, Daoru Han

Chemical and Biochemical Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith dust particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. a case study for a concept of electrostatic sieving was chosen to validate the new model. the simulation achieved similar performance of particle size classification as reported in the literature. the new model is computationally efficient (takes a few minutes on a PC-type laptop computer) so …

Development And Processing Of Shape Memory Polymer Composites (Smpcs) For Application In Structural Robotics And Robotic Sensors., Kavish Sudan

Electronic Theses and Dissertations

Shape Memory Polymers (SMPs) have attracted significant attention since their introduction in the 1980s due to their remarkable ability to regain their original shape from a temporarily deformed state when exposed to an external stimulus, typically heat. This shape memory effect, driven by thermal transitions such as the glass transition temperature (T_g) or melting temperature (T_m), has made SMPs highly attractive for applications in soft robotics, aerospace, and biomedical devices. However, SMPs face challenges such as limited mechanical strength, thermal stability, and electrical conductivity, which hinder their broader adoption in advanced applications. To address these challenges, …

Sizing Wind Tunnel Heater For High Enthalpy Conditions, Justin M. Slavick

Master's Theses

This paper determines the feasibility of adding a heater to an existing blowdown supersonic wind tunnel to unlock new high-enthalpy test applications, considering cost and power requirements at a variety of different states. This process includes both modeling the current range of test section properties in Cal Poly's blowdown wind tunnel and determining the new range of properties that a heat exchanger could induce. These results are verified with a computational fluid dynamics study. Additionally, sublimation and ablation properties of materials are explored to create appropriate models to study atmospheric re-entry once the heat exchanger is implemented.

It is found …

Kissing Bond Assessment In Adhesive Bonded Carbon Fiber Reinforced Composites Using Dielectric Spectroscopy, Minhazur Rahman

Mechanical and Aerospace Engineering Dissertations - Archive

The widespread use of fiber-reinforced composites in industries such as space, aviation, automobiles, and construction necessitates the formation of robust composite joints between critical structural components. Although adhesive-bonded joints are superior with improved load distribution and reduced weight, they are often overlooked in favor of bolted joints and mechanical fasteners due to the lack of reliable Non-Destructive Evaluation (NDE) techniques for adhesive-bonded composites. The anisotropic nature of the substrate and the intricate interfacial interactions between the adherend and adhesive material present significant challenges for conventional NDE methods. Moreover, weak adhesive bonds can result from uncontrolled manufacturing parameters, such as accidental …

Experimental Investigations And Optimization Of 3d Printed Cellular Structures For Protection Against Traumatic Brain Injury, Aaron R. Jackson

Mechanical and Aerospace Engineering Dissertations - Archive

Traumatic Brain Injury (TBI) disrupts brain function due to head impacts, blast exposures, and ballistic penetrations. It is a significant cause of mental health issues and disability, particularly among military personnel. Historically, combat helmets were designed primarily to protect against fragments. However, recent data highlights the need for helmets that also protect against blast and blunt impacts. Effective TBI prevention requires helmets that address various energy threats while remaining lightweight. A critical metric in this effort is head acceleration, which is closely linked to injury across different scales of brain damage.

Four lattice structures were 3D printed using Digital ABS …

Development Of A 3d Printed Optimization-Driven Aeroelastically Scaled Wind Tunnel Model For High Aspect Ratio Flying Wings, Mikaela K. Leevy

Mechanical and Aerospace Engineering Theses - Archive

Design optimization coupled with 3D printing and parametric CAD offers a unique approach to investigating flutter phenomena by creating low-cost iterative aeroelastic wind tunnel models. Recently, there is an interest in studying flutter phenomena at low air speeds in flying wing configurations. The X-56 experimental flying wing was designed to investigate flutter phenomena and flutter suppression, which makes the X-56 a logical choice for the full-scale model. The goal of this work is to optimize, physically print, and geometrically characterize a scaled aeroelastic wind tunnel model. The 18% reduced scale X-56 model was optimized by matching the mode shapes to …

Graphene Reinforced Polymer Composite For Small-Scale Vertical Axis Wind Turbine Rotors, Kunal A. Bachim

Mechanical and Aerospace Engineering Theses - Archive

Polymers have evolved as an indispensable asset in various sectors ranging from packaging and construction to energy and aerospace. However, the accumulation of polymer waste poses a necessity to shift toward sustainable waste management processes. Mechanical recycling is a primary method in establishing a circular economy approach for polymers. However, a fundamental challenge arises in this process: a decrease in the mechanical performance of the recycled product compared to that of its pristine counterpart.

This project addresses the challenge of enhancing the recyclability of polyethylene terephthalate (PET) from discarded polymer material by incorporating graphene nanoparticles into the polymer matrix during …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Chemical and Biochemical Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. To this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. A dual-belt separator was designed to reduce middling. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

Mechanics Of Pure Bending And Eccentric Buckling In High-Strain Composite Structures, Jimesh D. Bhagatji, Oleksandr G. Kravchenko, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This paper presents fabrication, experimental testing, and progressive failure modeling to study the deformation of an ultra-thin composite beam. The research study examines the deformation modes of a post-deployed boom under repetitive pure bending loads using a four-point bending setup and …

Restoration Of Strength In Polyamide Woven Glass Fiber Organosheets By Hot Pressing, Mohammad Nazmus Saquib, Edwing Chaparro-Chavez, Christopher Morris, Kuthan Çelebi, Diego Pedrazzoli, Mingfu Zhang, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Thermoplastic composite organosheets (OSs) are increasingly recognized as a viable solution for automotive and aerospace structures, offering a range of benefits including cost-effectiveness through high-rate production, lightweight design, impact resistance, formability, and recyclability. This study examines the impact response, post-impact strength evaluation, and hot-pressing repair effectiveness of woven glass fiber nylon composite OSs across varying impact energy levels. Experimental investigations involved subjecting composite specimens to impact at varying energy levels using a drop-tower test rig, followed by compression-after-impact (CAI) tests. The results underscore the exceptional damage tolerance and improved residual compressive strength of the OSs compared to traditional thermoset composites. …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. A prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. An alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. a prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. an alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

High-Fidelity Coupling For Studies Of Ablative Materials At Hypersonic Conditions, Aleksander Zibitsker

Theses and Dissertations--Mechanical and Aerospace Engineering

The development of accurate models and robust numerical tools for simulating ablative thermal protection materials (TPMs) in hypersonic flows is crucial for advancing atmospheric entry and hypersonic technologies. Traditional methods for simulating ablative materials often rely on heavy assumptions, such as equal heat and mass transfer coefficients and chemical equilibrium in the boundary layer, leading to conservative thermal protection system (TPS) designs and insufficient accuracy for certain in-flight ablation phenomena.

This work presents a high-fidelity and versatile coupled framework between hypersonic flow and material response solvers. The flow domain is modeled with an innovative overset CHAMPS NBS-Cart solver, which features …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Ambient Temperature Strength Degradation Of A Ceramic Matrix Composite Due To Solid Particle Erosion, Jonathan Clawson

Williams Honors College, Honors Research Projects

Solid particle erosion (SPE) is an issue for aircraft exposed to hard, fine particles, such as sand or dust, that can be ingested into the engine at a high velocity without reaching their melting point, resulting in material removal. SPE can be attributed to the intake of particulate debris from the runway or from airborne particulates. The cumulative mass loss from SPE damage affects the structural integrity and performance of the engine; however, its effects on ceramic matrix composites (CMCs), that are being employed in the aerospace industry, are not well understood in literature. The limited SPE research studies that …

Machine Learning-Assisted Multiscale Simulation And Design Optimization Of Composite Jackets Under Low-Velocity Impacts, Masoud Mohammadi

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research presents the development of a data-driven machine learning-assisted approach to simulate and optimize the design of composite materials subjected to low-velocity impacts. It focuses on a specific type of hybrid composite comprised of fiberglass and Kevlar fabrics stitched with Kevlar threads. The study begins by creating a multiscale finite element simulation for the composite under a low-velocity impact, which operates across three scales: microscale, mesoscale, and macroscale. This simulation accepts various inputs, such as different layer configurations and orientations, and provides impact outputs including maximum load and energy absorption capacity and displacement at failure.

Python and MATLAB scripts …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. to this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. a dual-belt separator was designed to reduce middlings. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. the simulation achieved similar yields reported in previous works, which served as validation of the model. the new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Additive Manufacturing And Characterization Of Auxetic Structures, Jayesh P. Moore, Stephanie R. Ruzicka

College of Engineering Summer Undergraduate Research Program

An auxetic structure is an arrangement of unit cells that under a uniaxial load experiences expansion in both the longitudinal and transverse directions, resulting in a negative Poisson’s ratio (NPR). Research in auxetics has led to new insights into how non-linear mechanical reactions can be applied to various engineering fields. This project utilized stereolithography (SLA) 3D printing to manufacture auxetic test specimens to analyze of geometry-driven NPRs. With the distinctive mechanical properties of auxetic structures and vast applications, the future of product development of these geometries seems promising.

Empowering Student Success: Unlocking The Potential Of Project-Based Steel Design Education, Aly Mousaad Aly

Faculty Publications

In the pursuit of student success, it is essential to acknowledge that a singular teaching style does not universally cater to all students. The educator's crucial role lies in creating an optimal learning environment that fosters students' endeavors to excel. This endeavor transcends mere classroom success or employment prospects, encompassing a broader impact on societal well-being. An experiential learning approach, where students actively engage in practical tasks, emerges as the most effective mode of instruction. Integrating project-based learning activities into the curriculum holds immense potential for enhancing student learning. Additionally, the utilization of analysis software tools like FTool and STAAD …

Effects Of Alternative Jet Fuels On Aerospace-Grade Composites: Experimental And Modeling Studies, Naoufal Harich

Theses and Dissertations

The aviation industry aims to reduce its environmental impact through innovation and research. The usage of composite materials for multiple primary structures represents one such measure. Several alternative fuels were approved and used along with the Federal Aviation Administration (FAA). These alternative fuels are produced from wastes and biomasses. Some alternative fuels were initially only approved as drop-in fuels, meaning they must be blended with conventional fuels to operate. Fuel tanks are usually embedded into the wing structure, which is mainly made of composite materials. These composites tend to absorb fluids it encounters through their matrix phase. The absorption behavior …