Propulsion and Power Commons^™

Optimal Battery Weight Fraction For Serial Hybrid Propulsion System In Aircraft Design, Tsz Him Yeung

Doctoral Dissertations and Master's Theses

This thesis focuses on electric propulsion technology associated with serial hybrid power plants most commonly associated with urban air mobility vehicles. While closed form analytical solutions for parallel hybrid aviation cases have been determined, optimized serial hybrid power plants have not seen the same degree of fidelity. Presented here are the analytical relationships between several preliminary aircraft design objectives and the battery weight fraction. These design objectives include aircraft weight, range, operation cost, and carbon emissions. The relationships are based on a serial hybrid electric propulsion architecture from an energy standpoint, and can be applied to hybrid aircraft of different …

End To End Satellite Servicing And Space Debris Management, Aman Chandra, Himangshu Kalita, Roberto Furfaro, Jekan Thanga

Space Traffic Management Conference

There is growing demand for satellite swarms and constellations for global positioning, remote sensing and relay communication in higher LEO orbits. This will result in many obsolete, damaged and abandoned satellites that will remain on-orbit beyond 25 years. These abandoned satellites and space debris maybe economically valuable orbital real-estate and resources that can be reused, repaired or upgraded for future use. Space traffic management is critical to repair damaged satellites, divert satellites into warehouse orbits and effectively deorbit satellites and space debris that are beyond repair and salvage. Current methods for on-orbit capture, servicing and repair require a large service …

Advanced Inflatable De-Orbit Solutions For Derelict Satellites And Orbital Debris, Aman Chandra, Greg Wilburn, Jekan Thanga

Space Traffic Management Conference

The exponential rise in small-satellites and CubeSats in Low Earth Orbit (LEO) poses important challenges for future space traffic management. At altitudes of 600 km and lower, aerodynamic drag accelerates de-orbiting of satellites. However, placement of satellites at higher altitudes required for constellations pose important challenges. The satellites will require on-board propulsion to lower their orbits to 600 km and let aerodynamic drag take-over. In this work we analyze solutions for de-orbiting satellites at altitudes of up to 3000 km. We consider a modular robotic de-orbit device that has stowed volume of a regular CubeSat. The de-orbit device would be …

Lasers For Communication And Coordination Control Of Spacecraft Swarms, Himangshu Kalita, Leonard Dean Vance, Vishnu Reddy, Jekan Thanga

Space Traffic Management Conference

Swarms of small spacecraft offer whole new capabilities in Earth observation, global positioning and communications compared to a large monolithic spacecraft. These small spacecraft can provide bigger apertures that increase gain in communication antennas, increase area coverage or effective resolution of distributed cameras and enable persistent observation of ground or space targets. However, there remain important challenges in operating large number of spacecrafts at once. Current methods would require a large number of ground operators monitor and actively control these spacecraft which poses challenges in terms of coordination and control which prevents the technology from scaled up in cost-effective manner. …

Project Atlas: A Mobile Universal Rocket Engine Test Stand, Collin Mickels, Conrad H. Wright, Noah Soderquist, Alona Prokofieva, Sattar Panahandehgar, Naveen Sri Uddanti, Alcuin Rajan

Student Works

Project Atlas is a mobile, trailer-mounted, rocket engine test stand developed by Experimental Rocket Propulsion Lab (ERPL) at Embry-Riddle Aeronautical University’s Daytona Beach, Florida campus. The integrated test stand and automated data-acquisition and control system supports ERPL’s multitude of engine research projects, including bipropellant liquid and hybrid rocket engines. The need for an integrated universal mobile test stand stems from the inability to conduct frequent test fires on campus due to Class-3 airspace and liability issues. The test stand is designed as a horizontal thrust structure utilizing a dual flame duct to redirect and cancel reaction forces acting upon the …

A Thrust Equation Treats Propellers And Rotors As Aerodynamic Cycles And Calculates Their Thrust Without Resorting To The Blade Element Method, Phillip -. Burgers

International Journal of Aviation, Aeronautics, and Aerospace

The lift generated by a translating wing of known translational speed, lift coefficient and area is calculated by a simple equation. A propeller or rotor generating thrust share the same aerodynamic principles but their different kinematics cause the calculation of their thrust to be laborious. This paper derives a thrust equation from an algebraic expansion of the Prandtl’s dynamic pressure term q_∞by adding the rotational kinetic energy of a propeller or rotor to the existing translational kinetic energy term. This thrust equation can be applied directly to propellers and rotors and assumes these to operate as cycles with …

Optimization And Analysis Of An Elite Electric Propulsion System, Mehakveer Singh, Kapil Yadav, Satnam Singh, Vikas Chumber, Harikrishna Chavhan

International Journal of Aviation, Aeronautics, and Aerospace

Abstract- Electric propulsion has a promising system to create new possibilities in this technological era as well as control the harmful gaseous emission. This paper put a vision on several parameters of electric propulsion. The engine’s performance is comparable to the current propulsion devices and provides a lightweight solution to the robust technologies’ dependent on chemical energy sources. There are a plethora of factors which is enhanced by electric propulsion such as, overall efficiency, capabilities, and robustness of future air vehicles as well as mainly overcome from exhaust hazards. Electric propulsion systems have the potential of utilizing the electrically-driven propulsion …

Effect Of Chemical Reactions On The Fluidic Thrust Vectoring Of An Axisymmetric Nozzle, Rachid Chouicha, Mohamed Sellam, Said Bergheul

International Journal of Aviation, Aeronautics, and Aerospace

Abstract:

During the last years, several thrust control systems of aerospace rocket engines have been developed. The fluidic thrust vectoring is one of them; it is simple in design and offers a substantial gain in weight and in performance. Most of studies related to this device were carried out with cold gas. It’s quite legitimate to expect that the thermophysical properties of the gases may affect considerably the flow behavior. Besides, the effects of reacting gases at high temperatures, under their effects all flow parameters like to vary.

This study aims to develop a new methodology that allows studying and …

Simulations On Optimization Of Liquid Spray Burners & Operating Parameters, Pallavi Gajjar, Vinayak Malhotra

International Journal of Aviation, Aeronautics, and Aerospace

Spray burners form an essential part of any liquid propulsion system as they are responsible for injecting, atomizing, mixing and combusting the liquid fuel. Spray combustion used in aerospace applications like the liquid rocket engines, gas turbines or any other controlled environment for that matter places a huge emphasis on safe and effective operations. These applications make use of relatively small amounts of propellant volumes to generate enormous amounts of energy through combustion for producing thrust. For such cases involving enormous energy interactions, combustion comes with its own set of challenges. The predominant challenge among them all is that of …

Ultrafine Aluminium: Quench Collection Of Agglomerates, Tejasvi K, Y Pydi Setty, Vemana Venkateswara Rao

International Journal of Aviation, Aeronautics, and Aerospace

Combustion of aluminized solid propellants exhibits phenomena associated with accumulation, agglomeration, ignition, and combustion of ultra-fine aluminium particles. In this study, agglomeration phenomenon of ultra-fine aluminium in solid propellant combustion is investigated using quench collection experimental technique over the pressure ranges from 2MPa to 8MPa. The ultra-fine aluminium powder synthesized by Radio Frequency Induction Plasma technique having harmonic mean size of 438nm is used for agglomeration study. The quenching distance is varied from 5mm to 71mm from the propellant burning surface to estimate the effect on agglomerate size. The morphology and chemical compositions of the collected products were then studied …

Satellite Maintenance: An Opportunity To Minimize The Kessler Effect, Bettina M. Mrusek Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Recently, there has been an emphasis on the growing problem of orbital debris. While the advantages of placing satellites into space are numerous, advances in satellite technology combined with the growth of the industry have resulted with a significant amount of debris in the orbits surrounding our planet. The harshness of the space environment has also contributed to the debris, as evidenced by the number of objects currently in orbit which are not operational. As the amount of debris grows, so too does the likelihood of collisions, ultimately culminating in the Kessler Effect. However, recent advances in propulsion, advanced navigation, …

Design Of A Heavy Lift Rc Aircraft - Society Of Automotive Engineers (Sae) Aero Design® West Competition Team, Jiyoung Hwang, Phillip Nielsen

Undergraduate Research Symposium - Prescott

The SAE Aero West design competition challenges undergraduate students to design and build an RC aircraft that will fly with the maximum number of passengers and luggage possible. The ERAU SAE team focuses on simulation-based research and project methods such as Computational Fluid Dynamics (CFD), aircraft optimization, and Finite Element Analysis (FEA). Designing and manufacturing a well-designed heavy lift aircraft and competing with other groups will give experience in solving engineering problems. The Aerodynamics team is currently focusing on score optimization, aircraft performance and configuration. The propulsion team is constructing a test rig to test various propellers and motors to …

Design Of A Thrust Stand For Low Power Electric Propulsion, John Norton

Undergraduate Research Symposium - Prescott

Electric propulsion (EP) has been gaining popularity due to the high efficiencies and specific impulse. These thrusters all follow the same general idea of converting stored electrical potential energy to kinetic energy for the craft; typically, this is accomplished by the acceleration of gas particles through three main methods, electrothermal, electromagnetic, and/or electrostatic. The specific impulse is the change of momentum per unit of propellant expended. While chemical propulsion produces a high change in momentum, they use much more propellant mass than an electric thruster. EP devices will typically produce very low thrust, which makes it difficult to measure thrust …

Floating Active Baffles, System And Method Of Slosh Damping Comprising The Same, Dae Won Kim, Rudy L. Baum, Vijay Santhanam, Balaji Sivasubramanian, Sathya Gangadharan

Publications

This disclosure provides a system for damping slosh of a liquid within a tank, a baffle for use in the system, and a method of damping slosh using the system. The system includes a plurality of baffles. Each baffle has a body configured to substantially float upon the liquid. Each baffle also has an activation material received along at least a portion of the body. The activation material is magnetically reactive provided in a quantity sufficient to enable the body to be manipulated in the presence of a magnetic field (M). The system further includes an actuator configured to pro­vide …

Clean-Fuel E-Vtol Air Mobility Vehicles For Unmanned And Manned Operations, Larry D. Mccarroll, Brian Morrison, Bruce J. Holmes D.E., Faiaa, Fraes, Henry Vu

National Training Aircraft Symposium (NTAS)

Imagine for a moment, having your very own safe, affordable, clean-fuel, point-to-any point vehicle for travel in the 21st-century 3-dimensional airspace system. Your ultra-reliable e-VTOL allows commuters to leave behind the constraints of hub-and-spoke airports, and the congestion of interstates, turnpikes and freeways. Facilitating Inter- and Intra-urban travel, such as downtown-to-airport, or metropolis-to-metropolis, or home-to-work. Perfect for dense urban environments worldwide. And all while offering the clean power of hydrogen for zero-emission travel.

This vision for efficient, clean, delay-free mobility has been talked about for decades, but always waived aside as some kind of futurist vision. This future requires tackling …

Experiments Of Propeller-Induced Flow Effects On A Low-Reynolds-Number Wing, Gavin K. Ananda, Robert Deters, Michael S. Selig

Publications

Novel findings are discussed in this paper that will be especially beneficial to designers and modelers of small-scale unmanned air vehicles and high-altitude long-endurance vehicles that both operate at low Reynolds numbers (Re = 50,000-300,000). Propeller-induced Oow effects in both tractor and pusher configurations on a recta ngular wing using the Wortmann FX 63-137 airfoil (a common low-Reynolds-number high-lift airfoil) are presented in this paper . Significant performance benefits can be found for a wing in the tractor configuration. Experiments, including trip tests and upper-surface oil Dow visualization, show and verify that the propeller slipstream induces early transition to turbulent …

Propulsive Battery Packs Sizing For Aviation Applications, Tianyuan Zhao

Doctoral Dissertations and Master's Theses

This thesis derives analytical methods for sizing the propulsive battery packs for designing an electric-driven aircraft. Lithium-Ion (Li-Ion) battery is the primary choice of battery cell chemistry in this thesis research due to its superior specific energy and market availability. The characteristics of Lithium-Ion battery cells are first determined and studied using experimental test results and manufacturers published data. Based on the design requirement to the battery system, the battery sizing will fall into one of the two sizing categories. The first category is power sizing, which requires the battery’s ability to deliver full power demanded by the electric motor. …

Algal Biofuel: The Future Of Green Jet Fuel In Air Transportation, Rajee Olaganathan

Publications

The aviation industry is one of the major contributors for the greenhouse gases. As air travel has become inevitable in this modern era, and fossil fuel usage is not sustainable, it is essential to produce renewable fuel and commercialize it to reduce the greenhouse gas emissions. In order to produce an alternate aviation biofuel a lot of industrial and academic collaborations have been developed worldwide. The main concern of this collaborative research is to produce aviation biofuel from renewable resources with low environmental impacts, and which is sustainable at an economically viable price. This mini-review briefly discusses the biotechnological approaches …

Unmanned Aerial Systems: Research, Development, Education & Training At Embry-Riddle Aeronautical University, Michael P. Hickey

Publications

With technological breakthroughs in miniaturized aircraft-related components, including but not limited to communications, computer systems and sensors, state-of-the-art unmanned aerial systems (UAS) have become a reality. This fast-growing industry is anticipating and responding to a myriad of societal applications that will provide new and more cost-effective solutions that previous technologies could not, or will replace activities that involved humans in flight with associated risks.

Embry-Riddle Aeronautical University has a long history of aviation-related research and education, and is heavily engaged in UAS activities. This document provides a summary of these activities, and is divided into two parts. The first part …

Application Of Artificial Neural Networks For The Prediction Of Aluminium Agglomeration Processes, Tejasvi K, Y Pydi Setty, Vemana Venkateswara Rao, Kalyan Chakarvarthy

International Journal of Aviation, Aeronautics, and Aerospace

Aluminium is universal and vital constituent in composite propellants and typically used to improve performance. Aluminum agglomeration takes place on the burning surface of aluminized propellants, which leads to reduced combustion efficiency and 2P flow losses. To understand the processes and behaviour of aluminum agglomeration, particles size distribution of composite propellants were studied using a quench particle collection technique, at 2 to 8 MPa and varying quench distances from 5mm to 71mm. To predict the agglomerate diameter of metallized/ultra-fine aluminium of composite propellants, a new artificial neural network (ANN) model was derived. Five Layered Feed Forward Back Propagation Neural Network …

Take-Off Characteristics For Naca 4612 Aerofoil In A Twin-Wing Configuration With Optimum Angles Of Attack, Elena Vishnevskaya, Kenneth L. Witcher, Ian R. Mcandrew

Publications

Unmanned Aerial Vehicles are used generally at low levels and speeds. The research reported in this article investigates the possible use of twin-wing designs for higher altitudes with a focus on the possible lift capable for either short runways or high payloads. The wing aerofoil and unique Angles of Attack, AoA, are set 5o on the upper wing and 10o on the lower. There is a positive upper wing stagger of 50% of the chord length at height separation of 1 chord. These parameters have been established from previous research and this research investigates how they generate lift at take-off …

Optimized Thruster Allocation Utilizing Dual Quaternions For The Asteroid Sample Return Mission (Osiris-Rex), Asher Smith

Doctoral Dissertations and Master's Theses

As spacecraft require higher positional accuracy from the attitude control systems, new algorithm developments, along with sensor and actuator resolution and range improvements are necessary to achieve the desired science accuracies. For agile 6-Degrees of freedom (6-DOF) spacecraft with redundancy, the actuators are usually oversized or overpopulated to meet the desired slew requirements. Currently, most spacecraft utilize an over-actuated thruster system to produce 6-DOF control. This thesis presents a simulation of the OSIRIS-REx mission during the descent phase to the asteroid Bennu, with a focus on utilizing dual quaternion dynamics and a newly developed thruster allocation method. The dual quaternion …

Aviation Propulsive Lithium-Ion Battery Packs State-Of-Charge And State-Of-Health Estimations And Propulsive Battery System Weight Analysis, Jingsi Lilly

Doctoral Dissertations and Master's Theses

Aviation propulsive battery pack research is in high demand with the development of electric and hybrid aircraft. Accurate inflight state-of-charge and state-of-health estimations of aviation battery packs still remain challenging. This thesis puts efforts on estimating the state-of-charge, state-of-health, and remaining energy of a lithium- ion propulsive battery pack with a recursive least squares based adaptive estimator. By reading the system measurements (discharging currents and terminal voltages) with persistent excitation, the proposed estimator can determine the present internal parameters of the battery cells and further interpolate them into state-of-charge, state-of-health, and the remaining energy information. The validation results indicate that …

Blended Wing Body Propulsion System Design, Parth Kumar, Adeel Khalid

International Journal of Aviation, Aeronautics, and Aerospace

This research paper focuses on the optimization of the propulsion system of a blended wing body design. Two different aspects of the design, the engine placement and count, and the engine itself, are investigated. The preliminary wing of the BWB is created through aerodynamic analysis, and is kept as a constant over the different propulsion system configurations. The engine parameters are first investigated. Equations are derived to express takeoff distance and climb rate as a function of engine sea level thrust, cruise thrust, and the number of engines. Nearly 150 different engine models, in BWB configurations of 2, 3, 4, …

Time Optimal State Feedback Control With Application To A Spacecraft With Cold Gas Propulsion, Samuel J. Kitchen-Mckinley, Sergey V. Drakunov

Publications

A cold gas propulsion system is well suited to provide the required thrust for a small surveyor spacecraft operated near an asteroid or planetary surface. The cold gas propellant can obtained in-situ from local surface or atmospheric constituents. For small spacecraft, the cold gas system may be limited to only on-off control of the main tank where the generated thrust is directly dependent on the tank pressure. As such the thrust will slowly decrease as the propellant is expended. A state feedback, time optimal, control law is developed for a vehicle with propellant is expended. A state feedback, time optimal, …

System And Method For Robust Nonlinear Regulation Control Of Unmanned Aerial Vehicles Synthetic Jet Actuators, Vladimir Golubev, William Mackunis

Publications

An unmanned aerial vehicle (UAV) is provided with a plurality of synthetic jet actuators and a nonlinear robust controller. The controller compensates for uncertainty in a mathematic model that describes the function of the synthetic jet actuators. Compensation is provided by the use of constant feedforward best guess estimates that eliminate the need for more highly computationally burdensome approaches such as the use of time-varying adaptive parameter estimation algorithms.

In-House Fabrication Of Temperature Sensitive Paint For Turbine Cooling Research, Mayur D. Patel, Mark A. Ricklick

Beyond: Undergraduate Research Journal

The Temperature Sensitive Paint (TSP) is a widely used method in measuring and visualizing flow separation and heat transfer. Compared to the cost and time consumption needed for methods such as pitot tubes, temperature sensitive paint is a cheaper alternative. Due to high usage in College of Engineering research projects, it was determined that in house fabrication of temperature sensitive paint would reduce time and cost limitations. For initial stages, literature research was performed to determine the recipe of intensity based TSP with luminophore and polymer binder that operated optimum at temperatures from 0-100°C. Europium III thenoyltrifluoroacetonate was determined to …

Variable Structure Feedback Control With Application To Spacecraft With Small Thrust Propulsion Systems, Samuel J. Kitchen-Mckinley

Doctoral Dissertations and Master's Theses

Small spacecrafts requiring small propulsion systems are becoming more popular for low Earth orbit. It is important for these research satellites to have accurate guidance and control systems. Small propulsion systems will also be beneficial for multiple small spacecrafts used future exploration expeditions beyond low Earth orbit. These small spacecrafts benefit from the simplicity of low thrust cold gas propulsion systems. Additionally, large spacecrafts using low thrust, high specific impulse propellants for main propulsion systems, such as ion engines, allow longer and more flexible missions, including Earth orbiting spacecraft and interplanetary spacecraft.

In order to extend the life of future …

Configuration Validation Of A Novel In-Space Propellant Storage And Transfer System, Priyadarshan Sundararaju

Doctoral Dissertations and Master's Theses

The concept of developing a new technology for on-orbit storage and refueling system has been a great interest among scientists for many decades. This study is about Centaur-based on-orbit propellant storage and transfer. This system takes the advantage of rotational settling to a simple fluid management (FM) system. Specifically, enabling settled fluid transfer and settled pressure control between two tanks. This thesis work focuses on configuration and validation of static and dynamic stability, mass gauging and CFD analysis of the rotational propellant transfer method in space. The application of this technology in Low Earth Orbit (LEO) and Geo-Synchronous Orbit (GEO) …

Multi-Stage Axial Compressor With Counter-Rotation Using Accessory Drive, Vinod Gehlot, Magdy S. Attia

Publications

A multi-stage axial compressor for counter rotation. A first series of rotor blade assemblies are mounted on and rotate with the driveshaft, each rotor blade assembly of the first series comprising a rotating stage of the multi-stage axial compressor. A second series of rotor blade assemblies provide a counter-rotating stage of the multi-stage axial compressor. An accessory drive links the second series of rotor blade assemblies to the driveshaft and causes counter-rotation of the second series of rotor blade assemblies.