Propulsion and Power Commons^™

Design And Development Of Supersonic Free Jet Facility, Gowtham Sai Somaroutu

Mechanical and Aerospace Engineering Theses - Archive

High-speed wind tunnels are essential facilities for conducting research and testing in external and internal flows. This thesis details the design and development of a blow-down supersonic free-jet facility with a 3-inch square nozzle in the Mach number range of and unit Reynolds number ranging. Key aspects of the facility development include the detailed design of the gas supply system, control valve selection, plenum, nozzle, test section, and the selection of an exhaust silencer. CAD designs for all the components of the facility were also generated in this effort.

A new analytical approach was developed to design supersonic contoured nozzles …

Uav To Carry Heavy Loads, Jacob Cannon, Robert Connor Downs, Anthony Orlando

Williams Honors College, Honors Research Projects

Our senior design project aims to develop an innovative Unmanned Aerial Vehicle (UAV) capable of carrying heavy payloads up to 50 lbs. This UAV will address the growing demand for efficient and autonomous cargo transportation, unlocking new possibilities in logistics and remote deliveries. The primary goal is to design, build, and test a robust UAV platform equipped with advanced propulsion systems, stabilizing mechanisms, and a secure payload attachment system. The heavy-lift UAV will be capable of transporting payloads in challenging environments, enhancing its versatility for various industries, including emergency response, disaster relief, and commercial logistics. For the extent of this …

Optimization Of High-Bypass Turbofan High-Pressure Compressor Blade – A Case Study, Adeel Khalid, Vlad Mandzyuk

The Kennesaw Journal of Undergraduate Research

This research determines the relationship between the High-Pressure Compressor (HPC) rotor blade design variables and compressor pressure ratio of a high bypass turbofan engine. Alterations in the HPC blades span, chord, taper, twist, number, and angle of incidence are performed and their effect on the HPC pressure ratio is observed. The objective is to determine key parameters that could maximize the performance of a high-pressure compressor for a given mission. Physics-based modeling, Computational Fluid Dynamics (CFD), and wind-tunnel testing are performed to compare and validate findings. Physics-based modeling is performed to serve as the benchmark for data obtained through other …

Analysis Of Variations In Flow-Independent Liquid Jet-In-Crossflow Injections, Michael Scott

Honors Undergraduate Theses

Liquid fuel injection is a critical mechanism for the deliverance of liquid fuel in contemporary aircraft propulsion combustion systems due to its outsized influence in providing optimal combustion conditions and improving overall aircraft efficiency and performance. Despite this, these liquid jet in crossflow (LJIC) systems are highly variable due to conditions in the jet and the surrounding airflow, leading to variability in performance behavior and inconsistency in fuel mixing and combustion efficiency. This has prompted the introduction of solid pintile obstructions of novel designs to provide a more flow-independent fuel injection scheme and decrease variability of the jet properties against …

Experimentatal And Numerical Investigation Of Turbojet Engine Performance, Emissions, And Noise/Vibrations Using Jet-A And F24 Fuel, John W. Mcafee Jr

College of Graduate Studies: Theses & Dissertations

Drastic improvement in cost effectiveness of high-power computing resources has generated a great interest numerical simulation to reduce the overhead cost of engine manufacturing, maintenance, and environmental concerns of engine testing. To accomplish this goal, this research presents the differences between military F24 fuel and commercial aviation fuel Jet-A from a thermochemical and engine performance perspective. This experimental data was used to create and validate a numerical model of the engine used in the experiments fueled with both Jet-A and F24 fuels. The experimental data was collected using a research based single stage turbojet engine outfitted with many sensors for …

Simulation Of Reacting Supersonic Flow In A Cavity Flameholder, Mohamed Benjelloun Touimi

Electronic Theses and Dissertations

Scramjet engines, or Supersonic Combustion Ramjets, are pivotal for achieving and maintaining hypersonic flight speeds. These engines leverage the high-speed airflow to compress and mix air and fuel for combustion. A significant challenge in Scramjet engine design is ensuring stable and efficient combustion within this high-speed environment. Cavity flameholders are crucial components that stabilize the combustion process by creating a subsonic region where the fuel-air mixture can ignite and sustain combustion. This research simulates this supersonic flow within the combustion chamber to accurately model and analyze the combustion dynamics. Various turbulence models, including RANS, and DES, are evaluated for their …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Superfly Amphibian, Devonte Andrews, Ahmed Hamza, Kwesi Onumah, Eva Sanchez

Senior Design Project For Engineers

Following a Short Takeoff and Landing (STOL) mission profile, this seaplane is designed to carry 19 passengers and 1 flight crew with a range of 200 nautical miles. The seaplane is equipped with two turbo-prop engines and is economically comparable to current seaplanes in terms of servicing and operating expenses. The aircraft is capable of operating in remote locations with limited infrastructure due to its STOL abilities, allowing for increased access to difficult-to-reach areas. The seaplane's design incorporates modern materials and technologies to enhance efficiency, safety, and comfort for passengers and crew. The aircraft's versatility and cost-effectiveness make it an …

On The Simulation Of Supersonic Flame Holder Cavities With Openfoam, Zachary Chapman

Electronic Theses and Dissertations

One of the next major advancements in the aerospace industry will be hypersonic flight. However, to achieve hypersonic flight, propulsion systems capable of reaching hypersonic speeds need to be developed. One of the more promising hypersonic propulsion systems is the scramjet engine, however, several problems still need to be explored before reliable scramjet engines can be produced, the biggest being keeping the engine ignited. This has led to the use of flame holder cavities to create a region of subsonic flow within the engine to allow combustion to occur. High experimental costs make the use of computational fluid dynamic (CFD) …

Noise And Propulsive Efficiency Interactions For Rotors And Propellers At Constant Thrust, Riccardo Roiati

Doctoral Dissertations and Master's Theses

In the emerging market of Advanced Air Mobility (AAM), aerospace companies have been designing and prototyping electric and hybrid vehicles to revolutionize travel. These vehicles must have low noise and particulate emissions while also having enough propulsive efficiency to complete the mission. This thesis aims to study the relationship between noise and propulsive efficiency as related to any aircraft equipped with an electric motor and a variable pitch rotor/propeller. The combination of the electric motor with the variable pitch propeller/rotor allows for a decoupled rotational speed and torque generation, meaning that the electric motor can generate the same amount of …

Quasi 1d Modelling Of A Scramjet Engine Cycle Using Heiser-Pratt Approach, Asmaa Chakir

Theses and Dissertations

Scramjet engines are key for sustained hypersonic flights. Analytic models play a critical role in the preliminary design of a scramjet engine configuration. The objective of this research is to develop and validate a quasi-1D model for the scramjet engine encompassing inlet, isolator and combustor, to evaluate the impact of flight conditions and design parameters on the engine functionality. The model is developed assuming isentropic flow in the inlet with a single turn; modified Fanno-flow equations in the isolator that account for the area change of the core flow; and the combustor is modeled using Heiser-Pratt equations accounting for the …

Controller Platform Design And Demonstration For An Electric Aircraft Propulsion Driv, Rosten Sweeting

Graduate Theses and Dissertations

With the growth in the aerospace industry there has been a trend to optimize the performance of an aircraft by reducing fuel consumption and operational cost. Recent advancements in the field of power electronics have pushed towards the concepts of hybrid electric aircraft also known as more electrical aircrafts. In this work, a custom controller board for an electric aircraft propulsion drive was designed to drive a permanent magnet synchronous motor. Design of the controller board required knowledge of the topology selection and power module selections. Simulations of the system were performed using MATLAB/Simulink to analyze the overall performance of …

Direct Simulation And Reduced-Order Modeling Of Premixed Flame Response To Acoustic Modulation, Zheng Qiao

Theses and Dissertations

This dissertation introduces a general, predictive and cost-efficient reduced-order modeling (ROM) technique for characterization of flame response under acoustic modulation. The model is built upon the kinematic flame model–G-equation to describe the flame topology and dynamics, and the novelties of the ROM lie in i) a procedure to create the compatible base flow that can reproduce the correct flame geometry and ii) the use of a physically-consistent acoustic modulation field for the characterization of flame response. This ROM addresses the significant limitations of the classical kinematic model, which is only applicable to simple flame configurations and relies on ad-hoc models …

Computational Comparison Of Dual Bell, Expansion-Deflection, And Aerospike Nozzles, Manuel R. Abadie Ardon

Honors College Theses

In the search for a Single-Stage-to-Orbit rocket, Altitude Compensating Nozzles concepts (ACNs) have been proposed since the 1950s, but research has stalled despite the modern analysis tools available. These nozzle concepts offer optimum performance at two or more altitude settings. This research chose three of these concepts, these being the Dual Bell, Expansion-Deflection, and Aerospike, which were designed and analyzed at various pressure ratios (NPR=10,15,30,36,30,45) using Computational Fluid Dynamics (CFD) software FLUENT. Simulations generated pressure distributions along the nozzle wall, which allowed to calculate data values such as thrust coefficients. Nozzle efficiency is calculated from this data and used to …

Liquid Engine External Pressurizer (Leep), Emily Armbrust

Williams Honors College, Honors Research Projects

The purpose of this project is to take the current liquid rocket engine test stand design and implement an external pressurant instead of utilizing the 2-phase oxidizer vapor to pressurize itself and the fuel. The purpose behind the design is because the team is limited with the current design concerning burn time due to the amount of propellant they can put in the tanks and the pressure it can reach. The initial pressure is currently not held since there is no external input of mass into the tanks, as the propellant is leaving. Adding an external pressurant allow for the …

A Non-Reacting Passive Scalar Comparison Of Starccm And Openfoam In A Supersonic Cavity Flame Holder, Thomas Nuese

Electronic Theses and Dissertations

The scramjet engine equipped with a modern-day airliner would allow for very quick travel across the United States. The major problem is that designing such an engine and testing it to make sure it is safe would cost millions if not billions of dollars. Computational fluid dynamics allows for complex designs to be tested but can still take many days, weeks, or even months to complete. With the use of computational fluid dynamics (CFD), the scramjet engine can be analyzed to determine a quicker way to test and develop a reliable configuration in addition to analyzing the effects of different …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

College of Graduate Studies: Theses & Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

Blade Optimization For Ground Level Low Speed Wind Turbines, Ryan Foster

Symposium of Student Scholars

Low speed wind turbines can provide inexpensive and clean energy in areas where large scale wind power generation is impractical. The purpose of this research is to explore factors that affect the efficiency of low speed wind turbine blades. The factors that were tested include angle of attack, angle of twist, chord length, average thickness, span, and taper ratio. The goal is to determine a combination of these variables to enable maximum power extraction from a low wind speed source. These blade parameters are optimized for the Southeastern region of the United States. NOAA weather data at ground level are …

Active Control Of Coherent Structures In An Axisymmetric Jet, Michael Marques Goncalves

Doctoral Dissertations and Master's Theses

The primary objective of this work is to develop high-fidelity simulation model for jet noise control predictions and quantify the sound reduction when an external source frequency mode excitation is imposed on the jet flow. Whereas passive approaches using mixing devices, such as chevrons, have been shown to reduce low-frequency noise in jet engines, such approaches incur a performance penalty since they result in a reduced thrust. To avoid a performance penalty in reducing jet noise, the current work investigates a open-loop active noise control (ANC) system that utilizes a unsteady microjet actuator on the nozzle lip in the downstream …

Design And Flight-Path Simulation Of A Dynamic-Soaring Uav, Gladston Joseph

Doctoral Dissertations and Master's Theses

We address the development of a dynamic-soaring capable unmanned aerial vehicle (UAV) optimized for long-duration flight with no on-board power consumption. The UAV’s aerodynamic properties are captured with the integration of variable fidelity aerodynamic analyses. In addition to this, a 6 degree-of-freedom flight simulation environment is designed to include the effects of atmospheric wind conditions. A simple flight control system aids in the development of the dynamic soaring maneuver. A modular design paradigm is adopted for the aircraft dynamics model, which makes it conducive to use the same environment to simulate other aircraft models. Multiple wind-shear models are synthesized to …

Perfromance Improvement Of High Bypass Turbofan Engine Through Optimization Of High-Pressure Compressor Blade – A Case Study, Vlad Mandzyuk

Symposium of Student Scholars

This research determines the relation between the High-Pressure Compressor (HPC) blade characteristics, compressor pressure ratio, and lift-to-drag ratio of a high bypass turbofan engine. Alterations in the HPC blades airfoil, span, chord, taper ratio, twist, aspect ratio, sweep, and angle of incidence are performed and their effect on the engine’s performance is observed. The metrics used to compare engine performance include thrust, specific thrust, exit velocity, fuel/air ratio, power, and efficiency. Parametric cycle analysis and computational fluid dynamics are performed to compare and validate findings. The goal of this study is to optimize the design of HPC to maximize the …

Computational Investigation Of Perforated Plate Film Cooling Utilizing Conjugate Heat Transfer, Jonathan Sippel

Doctoral Dissertations and Master's Theses

The accuracy of modern state-of-practice computational fluid dynamics approaches in predicting the cooling effectiveness of a perforated plate film-cooling arrangement is evaluated in ANSYS Fluent. A numerical investigation is performed using the Reynolds Averaged Navier Stokes equations and compared to NASA Glenn’s available Turbulent Heat Flux 4 experimental measurements collected as a part of the Transformational Tools and Technologies Project. A multiphysics approach to model heat conduction through the solid geometry is shown to offer significant improvements in wall temperature and film effectiveness prediction accuracy over the standard adiabatic wall approach. Additionally, localized gradient-based grid adaption is analyzed using the …

Analysis On Fuel Options For Scramjet Engines With The Study To Lower The Starting Mach Number, Sumantra Luitel, Gagan Dangi

Honors Theses

The main objectives of this report were to perform analysis of an ideal scramjet engine, to assess the influence of fuel on endurance factor, and the possibility of lowering the starting Mach Number of the scramjet. In the first part, an ideal cycle parametric analysis was conducted on three different fuels i.e. Liquid Hydrogen (LH2), Jet Propellant 7 (JP-7), and Rocket Propellant (RP-1), taking into account their availability, physical properties, current uses, and potential uses. The detailed analysis is done largely relying on a 9 step Parametric Cycle Analysis technique to study how fuel properties influence the variation of seven …

Sensitivity And Estimation Of Aerodynamic, Propulsion, And Inertial Parameters For Rudderless Aircraft Using Simulation, Jaden W. Thurgood

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A technique known as system identification is often used in aircraft design and testing to understand and validate the mathematical parameters that describe the aircrafts stability and handling characteristics. System identification can be thought of as the inverse of simulation. In the world of system identification, we have a physical system that we seek to understand in more detail by monitoring the system with an array of sensors. In short, we conduct tests of an aircraft while recording the inputs and response outputs. Then we take the input and output data and run it through an algorithm that seeks to …

Ram Air-Turbine Of Minimum Drag, Raymond Akagi

Master's Theses

The primary motivation for this work was to predict the conditions that would yield minimum drag for a small Ram-Air Turbine used to provide a specified power requirement for a small flight test instrument called the Boundary Layer Data System. Actuator Disk Theory was used to provide an analytical model for this work.

Classic Actuator Disk Theory (CADT) or Froude’s Momentum Theory was initially established for quasi-one-dimensional flows and inviscid fluids to predict the power output, drag, and efficiency of energy-extracting devices as a function of wake and freestream velocities using the laws of Conservations of Mass, Momentum, and Energy. …

Numerical Analysis Of Aerospike Engine Nozzle Performance At Various Truncation Lengths, Sam Dakka Dr, Oliver Dennison

International Journal of Aviation, Aeronautics, and Aerospace

The aerospike engine was first devised in the early 1960s where it provided new means of reaching orbit in a single stage. The paper aimes to demonstrate the viability of the technology by showcasing the increased nozzle thrust efficiency over the conventional bell nozzle. Various truncations were applied to the nozzle and each was subjected to two conditions, an over-expansion and near optimum condition. The nozzle contour was developed using the simple approximation method and was chosen to replicate that of the XRS-2200. This anchored the data, thereby validating the computational fluid dynamics (CFD) simulation. Simulations were completed for at …

Celebrating 90-Orbits Around The Sun, Stafford Air & Space Museum

Programs

In celebration of the 90th birthday of Oklahoma astronaut and aerospace legend, Gen. Thomas P. Stafford, the Stafford Air & Space Museum in Weatherford, Oklahoma is offering free admission on September 17th, 2020.

Unless stated otherwise within this repository collection, all materials are shared under the following Creative Commons license: [Creative Commons Attribution-NonCommercial 4.0 International License].

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

Studies Of Oval Tube And Fin Heat Exchangers, Phillip Nielsen

Undergraduate Student Works

Heating Ventilation and air-conditioning (HVAC) is a system which changes the temperature of the surroundings for the purposes of cooling or heating. This system requires energy to maintain a temperature difference from the outside temperature. Optimizing the flow over the evaporator coils is one way to increase the cooling efficiency. This will reduce the power required to have a sustainable system. Optimizing the flow to increase the energy transfer between the fins and the incoming air could result in a greater Coefficient of Performance (COP). This will be achieved by changing the geometry of the tubes for greater interaction with …

Arizona Hyperloop: The Fifth Mode Of Transportation, Eleanor Pahl, Matthieu Rada

Discovery Day - Prescott

Arizona Hyperloop is a coalition between Embry-Riddle Aeronautical University and Arizona State University students competing in Elon Musk’s annual SpaceX Hyperloop Pod Competition. Hyperloop is the proposed “Fifth Mode of Transportation” - coined “a cross between a Concorde, a rail gun, and an air hockey table.” A hyperloop pod levitates and travels at nearly the speed of sound inside a vacuum tube, which eliminates air resistance. Musk hosts the annual competition to university students to encourage the evolution of urban transportation. The goal is to design, build, and race the fastest prototype pod at SpaceX’s mile-long test track in Hawthorne, …