Aeronautical Vehicles Commons^™

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Microgas Turbine Engine Characteristics Using Biofuel, Edmond Ing Huang Tan, William W. Liou

The Hilltop Review

Aviation fuels commonly used today are extracted from the kerosene fraction of the crude oil that is distilled between the gasoline and the diesel. Crude oil is not renewable and the world oil reserve is generally believed to be on the decline. In 2006, 6.3% of the world's refinery production was used for aviation fuel (Nygren et. al., 2009). At an estimated rate of 3% increase of fuel demand per year, aviation use alone will consume the world fuel production by 2026. Therefore, there is a need for the aviation industry to reduce its dependence on fossil fuels and, perhaps, …

Design And Flight Testing Of A Warping Wing For Autonomous Flight Control, Edward Brady Doepke

Theses and Dissertations--Mechanical and Aerospace Engineering

Inflatable-wing Unmanned Aerial Vehicles (UAVs) have the ability to be packed in a fraction of their deployed volume. This makes them ideal for many deployable UAV designs, but inflatable wings can be flexible and don’t have conventional control surfaces. This thesis will investigate the use of wing warping as a means of autonomous control for inflatable wings. Due to complexities associated with manufacturing inflatable structures a new method of rapid prototyping deformable wings is used in place of inflatables to decrease cost and design-cycle time. A UAV testbed was developed and integrated with the warping wings and flown in a …

Aerodynamics And Control Of A Deployable Wing Uav For Autonomous Flight, Michael Thamann

Theses and Dissertations--Mechanical and Aerospace Engineering

UAV development and usage has increased dramatically in the last 15 years. In this time frame the potential has been realized for deployable UAVs to the extent that a new class of UAV was defined for these systems. Inflatable wing UAVs provide a unique solution for deployable UAVs because they are highly packable (some collapsing to 5-10% of their deployed volume) and have the potential for the incorporation of wing shaping. In this thesis, aerodynamic coefficients and aileron effectiveness were derived from the equations of motion of aircraft as necessary parameters for autonomous flight. A wind tunnel experiment was performed …

Cal Poly Human Powered Helicopter, Josiah Auer, Eric Behne, Dave Berry, Rebecca Hennings, James Koch, Ian Marquardt, Josiah Mayfield, Sean Miller

Mechanical Engineering

The following report encompasses the Cal Poly Human Powered Helicopter team’s efforts during the 2010-2011 academic year. The intention of this project is to further the knowledge of human powered helicopter design and to validate an ideal configuration through experimental tests and analysis. 

A. Background

The Sikorsky Prize offered by the American Helicopter Society has been the catalyst for many attempts at Human Powered Helicopter (HPH) flight. The requirement to win the prize is a continuous, human powered flight of more than 60 seconds that stays within a 10 meter square box and reaches an altitude greater than 3 meters …

Airplane Landing Flare-The Last 5 Seconds, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Some Considerations For Regional Airline Operations On Contaminated Runways., Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Multidisciplinary Design Optimization Of Transonic Airfoil Sections Using Multiobjective Optimization And Computational Intelligence Tools, Amit A. Kulkarni

Mechanical & Aerospace Engineering Theses & Dissertations

The design of transonic airfoils for civil aviation applications has been a major engineering challenge in the last fifty years. This design problem arises due to the need to limit shock wave drag at a given transonic speed. In recent years, the requirement to reduce the levels of aircraft noise has started to affect the airfoil design process. The multidisciplinary aerodynamic shape optimization problem is treated in this thesis using a multi-objective approach. The objectives correspond to the design of transonic airfoil sections with low drag during cruise and low trailing edge noise levels during the approach condition. The optimization …

Experimental Flow Visualization For Corrugated Airfoils At Low Reynolds Number Including Development Of A Pitch And Plunge Fixture, Jeremy Ryan Sparks

University of Kentucky Master's Theses

Micro Air Vehicles (MAV’s) have small size and extreme maneuverability which makes them ideal for surveillance. Propulsion mechanisms include propellers, rotors, and flapping airfoils. Flapping motions, along with biologically-inspired wing profiles, are of interest due to their use of natural physics. Corrugated airfoil structures appears to have poor aerodynamic performance at higher Reynolds numbers, but serve well at Re<10,000. Understanding flow structures around corrugated profiles and comparing them to a standard airfoil will aid in understanding how these corrugated profiles perform well and have been adopted by some of nature’s most acrobatic flyers. Motivation for this investigation is to compare static flow visualizations of corrugated profiles to a standard National Advisory Committee for Aeronautics (NACA) airfoil from low to high angles of attack and further observe flow structure development of a pitching and plunging flat plate at a Re<10,000 and a Strouhal number relevant to natural fliers. The static visualization was conducted at Re=1,000 with a NACA 0012 airfoil and two corrugated models. The Pitch and Plunge Fixture (PPF) developed was constructed by simplifying flapping wings as a two degree of freedom motion in plunge (translation) and pitch (rotation). Results obtained from the PPF were compared with a numerical simulation.

Design Of A "Figure-8" Spherical Motion Flapping Wing For Miniature Uav's, Zohaib Parvaiz Rehmat

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hummingbirds and some insects exhibit a Figure-8 motion, which allows them to undergo variety of maneuvers including hovering. It is therefore desirable to have flapping wing miniature air vehicles (FWMAV) that can replicate this unique wing motion. In this research, a design of a flapping wing for FWMAV that can mimic Figure-8 motion using a spherical four bar mechanism is presented. To produce Figure-8 motion, the wing is attached to the coupler point of the spherical four bar mechanism and driven by a DC servo motor. For verification of the design, a prototype of the wing and mechanism is fabricated …

Load Interaction Effects On Fatigue Crack Growth, Stoyan Ivanov Stoychev

Dissertations

Load excursions, in the form of tensile and compressive overloads are known to produce interaction effects during subsequent constant amplitude loading. In this work, the fatigue crack growth and crack closure levels, under both constant amplitude and variable amplitude loading, are investigated in the aluminium-lithium alloy 2090-T84, and the aluminium alloys 2024-T351 and 7150-T651. The crack closure measurements were obtained using both a crack tip opening displacement (CTOD) gauge and a crack mouth opening displacement (CMOD) gauge.

Fatigue crack growth tests were performed on specimens of thickness 1.6mm, 3mm, 6mm and 14mm. Tests were performed at load ratios of 0.1 …

Numerical Study Of Combustion Of Hydrogen And Ethylene In A Two-Dimensional Dual-Mode Scramjet Combustor, Robert A. Carson

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents computational fluid dynamics results for two-dimensional flow geometries utilizing two fuels, hydrogen (H2) and ethylene (C2H4). Upstream interaction was evident with the use of both fuels due in part to recirculation in the combustor, the inlet pressures and the combustion process. Results were obtained for hydrogen using a reduced chemical kinetic model while results obtained for ethylene employed a reduced chemical kinetic model as well as an expanded chemical kinetic model.

Initially, an examination of grid composition was conducted in order to select the most numerically efficient and accurate grid for reacting flow in the current combustor …

Microstructural Study Of Nanoprecipitates In Rra Treated Al-7075 T6 Using Afm/Ufm/Stem, Samuel J.M. Kuhr, Margaret Pinnell, Daniel Eylon

Mechanical and Aerospace Engineering Faculty Publications

7075 T651 aluminum alloy is frequently used in aircraft applications for its high strength to weight ratio. However, aircraft parts made of this alloy have been plagued by stress corrosion cracking (SCC). Retrogression and re-aging (RRA) is a post T651 two-stage heat treatment that provides improved SCC resistance with minimal loss in tensile strength. In this study, various forms of microscopy and mechanical testing are used to investigate how the RRA process affects the microstructure.

The microscopic observations in this paper show that the precipitates in the aluminum alloy coarsen and that the grain boundary regions are depleted of copper …

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

Computation Of The Aerodynamic Characteristics Of A Subsonic Transport Aircraft Using A Panel Method, Lillianne Plaster Whitelock Troeger

Mechanical & Aerospace Engineering Theses & Dissertations

An advanced low-order panel method, VSAERO, is applied to a full-configuration transport aircraft. Wing pressure distributions as well as lift, drag, and pitching moment coefficients calculated for the full computational configuration are compared with experimental data. In addition, partial configurations are evaluated computationally to determine the relevance of certain complex aircraft components to the computations. It is shown that the wing-surface pressure distributions and pitching moment coefficient are well predicted by VSAERO. The lift coefficient is consistently overpredicted by the code.

An Experimental And Analytical Investigation Of Wing Flutter On A Trial Rotor V/Stol Aircraft, David L. Soistmann

Mechanical & Aerospace Engineering Theses & Dissertations

A wind tunnel model based on a trail rotor vehicle concept was tested for wing flutter in the subsonic flow regime. The wind tunnel model was flutter tested in the forward flight mode only. From this test it was determined that this conceptual vehicle may be susceptible to wing flutter. However, the flutter encountered was not catastrophic but was of the limited amplitude type. The trailing rotor blades were found to have a positive aerodynamic damping effect on flutter. The flutter mechanism for each flutter point was due to a coupling of the first wing bending and first wing torsion …

Effects Of Nose Bluntness And Shock-Shock Interactions On Blunt Bodies In Viscous Hypersonic Flows, Dal J. Singh

Mechanical & Aerospace Engineering Theses & Dissertations

A numerical study has been conducted to investigate the effects of blunt leading edges on the viscous flow field around a hypersonic vehicle such as the proposed National Aero-Space Plane. Attention is focused on two specific regions of the flow field. Analysis of these flow regions is required to accurately predict the overall flow field as well as to get necessary information on localized zones of high pressure and intense heating.

The forebody is modeled by slender cones and ogives with spherically blunted nose. A combination of Navier-Stokes and parabolized Navier-Stokes equations is used to compute the flow field. The …

Numerical Simulation Of Turbulent Flows Past Three-Dimensional Cavities, Shivakumar Srinivasan

Mechanical & Aerospace Engineering Theses & Dissertations

Computations have been performed to simulate turbulent supersonic, transonic, and subsonic flows past three-dimensional deep, transitional, and shallow cavities. Simulation of these self sustained oscillatory flows has been generated through time accurate solutions of Reynolds averaged full Navier-Stokes equations using the explicit MacCormack scheme. The Reynolds stresses have been modeled, using the Baldwin-Lomax algebraic turbulence model with certain modifications. The computational results include instantaneous and time averaged flow properties everywhere in the computational domain. Time series analyses have been performed for the instantaneous pressure values on the cavity floor. Comparison with experimental data is made in terms of the mean …

Studies On The Interference Of Wings And Propeller Slipstreams, Ramadas K. Prabhu

Mechanical & Aerospace Engineering Theses & Dissertations

The small disturbance potential flow theory is applied to determine the lift of an airfoil in a nonuniform parallel stream. The given stream is replaced by an equivalent stream with a certain number of velocity discontinuities, and the influence of these discontinuities is obtained by the method of images. Next, this method is extended to the problem of an airfoil in a nonuniform stream of smooth velocity profile. This model allows perturbation velocity potential in a rotational undisturbed stream. A comparison of these results with numerical solutions of Euler equations indicates that, although approximate, the present method provides useful information …

An Analytical Design Procedure For The Determination Of Effective Leading Edge Extensions On Thick Delta Wings, Farhad Ghaffari

Mechanical & Aerospace Engineering Theses & Dissertations

An analyt1cal des1gn procedure for Lead1ng-Edge Extensions (LEE) has been developed for thick delta wings. This LFE device is des1gned to be mounted to a w1ng along the pseudo-stagnation stream surface associated w1th the attached flow design lift coeff1cient of greater than zero. The intended purpose of the device is to improve the aerodynamic performance of high subsonic and low super son1c aircraft at incidences above that of attached flow design lift coefficient, by us1ng a vortex system emanating along the leading edges of the device. The low pressure assoc1ated with these vort1ces would act on the LEE upper surface …

Interaction Of A Two-Dimensional Transverse Jet With A Supersonic Mainstream, Gilbert Otto Kraemer

Mechanical & Aerospace Engineering Theses & Dissertations

A experimental investigation of the interaction of a twodimensional sonic jet injected transversely into a confined main flow has been conducted. The main flow consisted of air at a Mach number of 2.9. The effects of varying the jet parameters on the flow field were examined using surface pressure and composition data. Also, the downstream flow field was examined using static pressure, pitot pressure, and composition profile data. The jet parameters varied were gapwidth, jet static pressure, and injectant species of either helium or nitrogen. The values of the jet parameters used were 0.039, 0.056,and 0.109 cm for the gapwidth …

Analytic And Experimental Studies Of A True Airspeed Sensor, Joseph Yao-Cheng Shen

Mechanical & Aerospace Engineering Theses & Dissertations

The objective of this study was to analyze and design a true airspeed sensor which will replace the conventional pitot-static pressure transducer. This sensor should have the following characteristics: the flow phenomenon is vortex procession, or the "vortex whistle", it should have no moving parts, and also is to be independent of temperature, density, altitude or humidity changes. This sensor has been designed mainly for small commercial aircraft with the airspeed up to 321.9 km/hr (200 mph).

In an attempt to model the complicated fluid mechanics of the vortex precession, three-dimensional, inviscid, unsteady, incompressible fluid flow was studied by using …

Computer-Aided Design Of Light Aircraft To Meet Certain Aerodynamic And Structural Requirements, Joanne Lynn Walsh

Mechanical & Aerospace Engineering Theses & Dissertations

Nonlinear mathematical programming techniques are applied to a particular aircraft design problem, that of determining the maximum range design for light aircraft subject to certain aerodynamic and structural requirements. Search techniques available in an existing nonlinear optimization computer program, AESOP, are applied to the design problem. Seven design variables are used to define the wing dimensions, the wing skin thickness, the cruise velocity, the amount of fuel carried, and the engine horsepower. The influence of different design requirements on the range is observed and discussed.