Aerodynamics and Fluid Mechanics Commons^™

Experimental Environmental Profiles And Sloshing Dynamics Aboard Zero-G Aircraft, Pedro J. Llanos, Sathya Gangadharan, Kevin Crosby

Publications

This study presents the results of a parabolic flight experiment to study the sloshing dynamics of the magneto-active propellant management device experiment. This device utilizes a magnetoactive membrane and magnets located external to the tank to effectively damp the liquid free surface motion. This research work establishes a benchmark with sloshing analytical formulation and sensor calibration methods that can be used to characterize future research parabolic flights while providing important environmental profiles measured during flight, such as accelerations, pitch angle, velocity, temperature, total volatile content, carbon dioxide, relative humidity, magnetic field, and radiation. Correlation between these flight variables and the …

On Progress In Exploring Controlled Viscous Limit-Cycle Oscillations In Modified Glauert Airfoil, Ethan Deweese, Lap Nguyen, Erik Vataker, William Mackunis, Vladimir Golubev, Ron Efrati, Oksana Stalnov

Publications

The paper reports on the progress in the development of a novel robust, nonlinear flow control technology that employs an array of synthetic-jet actuators (SJAs) embedded in 2-DOF, elastically mounted, optimized Modified Glauert (MG) airfoil design in order to control limit cycle oscillations (LCO) at low subsonic flow regimes. The focus here is on the conceptual design of the wind energy harvesting system that employs, e.g., a piezoelectric device to extract energy from plunging LCO, with the closed-loop controller being capable to sustain the required LCO amplitudes over a wide range of wind speeds. The current high-fidelity studies first include …

Dynamics Of A 3-D Inlet/Isolator Measured With Fast Pressure-Sensitive Paint, Andrew N. Bustard, Mark E. Noftz, Mitsugu Hasegawa, Hirotaka Sakaue, Joseph S. Jewell, Nicholas J. Bisek, Thomas J. Juliano

Publications

Fast pressure-sensitive paint (PSP) was applied to an inlet/isolator designed using the Osculating Internal Waverider Inlet with Parallel Streamlines (OIWPS) method. The dorsal isolator surface pressure was measured using anodized-aluminum PSP through transparent cast acrylic that makes up the ventral portion of the isolator. Temperature-sensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at Re = 8.5 ×106 /m and 10.2 ×106 /m in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel (ANDLM6QT) under conventional noise conditions. Flow phenomena, such as shocks originating in the inlet and flow separation at the …

State Space Modeling And Estimation Of Flexible Structure Using The Theory Of Functional Connections, Carlo Lombardi, Riccardo Bevilacqua

Student Works

In this work, we present a novel method to model the dynamics of a continuous structure based on measurements taken at discrete points. The method is conceived to provide new instruments to address the problem of flexible dynamics modeling in a spacecraft, where an effective mathematical representation of the non-rigid behavior of the is of critical importance in the design of an effective and reliable attitude estimation and control system. Both the measurements and the model that describes the structure can be affected by uncertainty. The purpose of the developed method is to estimate the position and the velocity of …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

A Simulation Of The Impacts Of Climate Change On Civil Aircraft Takeoff Performance, Thomas D. Pellegrin

Doctoral Dissertations and Master's Theses

Climate change affects the near-surface environmental conditions that prevail at airports worldwide. Among these, air density and headwind speed are major determinants of takeoff performance, and their sensitivity to global warming carries potential operational and economic implications for the commercial air transport industry. Previous archival and prospective research observed a weakening in headwind strength and predicted an increase in near-surface temperatures, respectively, resulting in an increase in takeoff distances and weight restrictions. The main purpose of the present study was to update and generalize the extant prospective research using a more representative sample of worldwide airports, a wider range of …

Numerical Modeling Of Synthetic Vortical Disturbance Interactions Using Openfoam, Ahmed Bilal

Doctoral Dissertations and Master's Theses

Nowadays, the number of Advance Air Mobility (AAM) Electic Vertical Take-off and Landing (eVTOL) concepts is rapidly increasing due to their capability of vertical take-off and landing at vertiports located on rooftops of tall urban buildings, which does not require using the ground space in a condensed urban environment. Such flight operations, however, will be greatly affected by the vertiport’s highly unsteady, turbulent flow environment. The goal of this study is to model the turbulent wind interaction with a building to understand the unsteady flow characteristics around vertiports and match the induced unsteady disturbance field to the canonical disturbance forms, …

The Linearized Euler Equations For Predicting Supersonic Jet Noise Of A Rectangular Jet Using Openfoam, Patrick Good

Doctoral Dissertations and Master's Theses

This thesis presents a Linearized Euler Equation (LEE) solver that was developed for OpenFOAM. OpenFOAM is an open-source Computational Fluid Dynamics (CFD) package that is widely used by industry and academia. The LEE’s are a set of equations used in Computational Aeroacoustics (CAA). The LEE’s can solve for the acoustic solution directly and quickly. The solver developed, named leeFoam, was tested against analytical solutions to verify accuracy and then was utilized to predict the acoustics of a heated supersonic rectangular jet. The rectangular jet (RJET) results were compared against experimental data.

The results from this work show that OpenFOAM can …

Understanding The Structure Of Wing Tip Vortices Of Bio-Inspired Winglets, Greeshma C. Daniel

Doctoral Dissertations and Master's Theses

Bio-inspired wing tip devices were investigated with the goal of improving the fuel efficiency of subsonic aircraft. Particularly, the structure of a bio-inspired winglet design based on bird feathers were tested in a low-speed wind tunnel. Particle image velocimetry (PIV), was used to study the flow field at two planes aft of the wing as the wing tip vortices developed downstream. These were time-dependent, stereoscopic particle image velocimetry (sPIV) measurements carried out at two planes located at 0.7 and 2 chord distances downstream from the wing. The structure of the wingtip vortices was compared and contrasted with that formed over …

Prediction & Active Control Of Multi-Rotor Noise, Samuel O. Afari

Doctoral Dissertations and Master's Theses

Significant developments have been made in designing and implementation of Advanced Air Mobility Vehicles (AAMV). However, wider applications in urban areas require addressing several challenges, such as safety and quietness. These vehicles differ from conventional helicopter in that they operate at a relatively lower Reynolds number. More chiefly, they operate with multiples of rotors, which may pose some issues aerodynamically, as well as acoustically. The aim of this research is to first investigate the various noise sources in multi-rotor systems. High-fidelity simulations of two in-line counter-rotating propellers in hover, and in forward flight conditions are performed. Near field flow and …

Design Of An Internal Osculating Waverider Intake, Mark E. Noftz, Andrew J. Shuck, Joseph S. Jewell, Jonathan Poggie, Andrew N. Bustard, Thomas J. Juliano, Nicholas J. Bisek

Publications

The design of an inward-turning, high-speed, three-dimensional streamline traced intake is presented from osculating axisymmetric theory. To satisfy the osculating intake design criteria, a stitched Busemann diffuser and Internal Conical Flow-A solution is used as the basic isentropic compressive streamline. This new contour provides efficient compression, high flow uniformity, and straight leading edge shocks of equal strength. Additionally, a novel method for constructing the inlet cowl is presented. The combined process leads to a new method of high-speed intake design. A generic shape-transitioned intake is constructed and named the Indiana Inlet for the Indiana universities that contributed to the project. …

Noise And Propulsive Efficiency Interactions For Rotors And Propellers At Constant Thrust, Riccardo Roiati

Doctoral Dissertations and Master's Theses

In the emerging market of Advanced Air Mobility (AAM), aerospace companies have been designing and prototyping electric and hybrid vehicles to revolutionize travel. These vehicles must have low noise and particulate emissions while also having enough propulsive efficiency to complete the mission. This thesis aims to study the relationship between noise and propulsive efficiency as related to any aircraft equipped with an electric motor and a variable pitch rotor/propeller. The combination of the electric motor with the variable pitch propeller/rotor allows for a decoupled rotational speed and torque generation, meaning that the electric motor can generate the same amount of …

Development And Deployment Of A Dynamic Soaring Capable Uav Using Reinforcement Learning, Jacob Adamski

Doctoral Dissertations and Master's Theses

Dynamic soaring (DS) is a bio-inspired flight maneuver in which energy can be gained by flying through regions of vertical wind gradient such as the wind shear layer. With reinforcement learning (RL), a fixed wing unmanned aerial vehicle (UAV) can be trained to perform DS maneuvers optimally for a variety of wind shear conditions. To accomplish this task, a 6-degreesof- freedom (6DoF) flight simulation environment in MATLAB and Simulink has been developed which is based upon an off-the-shelf unmanned aerobatic glider. A combination of high-fidelity Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) in ANSYS Fluent and low-fidelity vortex lattice (VLM) …

Artificial Neural Network For Predicting Heat Transfer Rates In Supercritical Carbon Dioxide, Vinusha Dasarla Giri Babu

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide as a working fluid in a closed Brayton cycle is proving to be more efficient than a conventional steam-based Rankine engine. Understanding the heat transfer properties of supercritical fluids is important for the design of a working engine cycle. The thermophysical properties of supercritical fluids tend to vary non-linearly near the pseudo-critical region. Traditionally, empirical correlations are used to calculate the heat transfer coefficient. It has been shown in the literature and within our own studies that these correlations provide inaccurate predictions near the pseudo-critical line, where heat transfer may be deteriorated or enhanced, resulting from strong …

A Study Of Ship Airwakes Using Dual Plane Stereoscopic Piv, Guillermo Mazzilli

Doctoral Dissertations and Master's Theses

The airwake of a model Simple Frigate Shape 2 (SFS2) was studied in a low-speed wind tunnel. This airwake was measured using a novel time-dependent, dual plane, stereoscopic particle image velocimetry approach. Two flow planes over the flight deck, one parallel and one perpendicular to the free-stream were simultaneously measured. Measurements were carried out over four such pairs of streamwise-spanwise plane combinations. Additionally, the airwake with and without a simulated atmospheric boundary layer (sABL) was studied. The synchronicity of the measurements were taken advantage of to carry out conditional averages of the flow field to isolate and study certain flow …

Understanding Unsteady Corner Separation Within Wing-Body Junction Flows, Paul G. Winner

Doctoral Dissertations and Master's Theses

Wing-body junction flows, formed at the interface between a wing and fuselage surface, are a complex, coupled, three-dimensional, turbulent flow field. This thesis focused on the unsteady corner separation that develops at the trailing edge of this wing-body junction under certain conditions. A NACA 0015 wing mounted on a flat plate at an angle of attack of 13°was used as the model junction flow field. The wing had an aspect ratio of 8 with a linear washout twist of 15°. The Reynolds number based on the wing chord was Re_c = 4.5 × 10⁵. Time-dependent stereoscopic particle …

A Data Driven Modeling Approach For Store Distributed Load And Trajectory Prediction, Nicholas Peters

Doctoral Dissertations and Master's Theses

The task of achieving successful store separation from aircraft and spacecraft has historically been and continues to be, a critical issue for the aerospace industry. Whether it be from store-on-store wake interactions, store-parent body interactions or free stream turbulence, a failed case of store separation poses a serious risk to aircraft operators. Cases of failed store separation do not simply imply missing an intended target, but also bring the risk of collision with, and destruction of, the parent body vehicle. Given this risk, numerous well-tested procedures have been developed to help analyze store separation within the safe confines of wind …

Comprehensive Review Of Heat Transfer Correlations Of Supercritical Co2 In Straight Tubes Near The Critical Point: A Historical Perspective, Nicholas C. Lopes, Yang Chao, Vinusha Dasarla, Neil P. Sullivan, Mark Ricklick, Sandra Boetcher

Publications

An exhaustive review was undertaken to assemble all available correlations for supercritical CO2 in straight, round tubes of any orientation with special attention paid to how the wildly varying fluid properties near the critical point are handled. The assemblage of correlations, and subsequent discussion, is presented from a historical perspective, starting from pioneering work on the topic in the 1950s to the modern day. Despite the growing sophistication of sCO2 heat transfer correlations, modern correlations are still only generally applicable over a relatively small range of operating conditions, and there has not been a substantial increase in predictive capabilities. Recently, …

Experimental Characterization Of Additively Manufactured Multi-Feather Wingtip Devices, Patricio Garzon

Doctoral Dissertations and Master's Theses

Soaring birds have evolved to fly for long periods of time without flapping their wings. Inspired by the flight of these birds, the proposed thesis presents an experimental investigation focused on wingtip devices designed based on biomimicry. The overarching engineering objective was to reduce the induced drag as a means to improve the fuel efficiency via these experimental wingtips. An associated secondary objective was to establish a method for manufacturing complex structures suitable for wing tunnel testing. A manufacturing technique that involved using composite weaves to reinforce additively manufactured structures was developed. This technique has the potential to reduce manufacturing …

Effect Of Spray Rails On Takeoff Performance Of Amphibian Aircraft, Soham Bahulekar

Doctoral Dissertations and Master's Theses

Amphibian aircraft have seen a rise in popularity in the recreational and utility sectors due to their ability to take off and land on both land and water, thus serving a myriad of purposes such as aerobatics, surveillance, and firefighting. The design of such seaplanes requires to be both aerodynamically and hydrodynamically efficient, especially during the takeoff phase. In the past, naval architects have implemented ways to make boats, yachts, and large ships more efficient; one of them being the addition of chine strips and spray rails on the hull. This thesis study explores the possibility of implementing spray rails …

Time-Resolved Piv Measurements Of Ship Airwakes With Quartering Winds, Kaijus H. Palm

Doctoral Dissertations and Master's Theses

The unsteady, three-dimensional, turbulent airwake over the Simple Frigate Ship No. 2 (SFS2) with quartering wind flow directions was studied in a low-speed wind tunnel facility. Surface oil flow visualization and time-resolved stereoscopic and planar particle image velocimetry (PIV) measurements were made for three crosswise planes and a single centerline streamwise plane. Measurements included various configurations with the bow of the ship model at two different quartering wind conditions of 10 and 20 degrees, as well as cases with and without the effects of a simulated atmospheric boundary layer (ABL). A comparative analysis of the time-averaged flow structures between the …

Influence Of Wing Planform Shape On The Effectiveness Of A Fixed-Slot, Yuan Zhao

Doctoral Dissertations and Master's Theses

This thesis report explores the effect of the Clark-Y wing geometry on lift and drag to use as a reference during aircraft design stage. The different characteristics investigated are fixed slot span, taper ratio, washout, and sweep angle. Plain wings, half slotted wings, and fully slotted wings were built in CATIA with an aspect ratio of 6 and different taper ratio, washout, and sweep angles. Using the CATIA models to generate the 3-D grids in Pointwise. All the simulations were tested in Ansys-Fluent under sea-level conditions with a Reynold number of 609000. The relationships between the aerodynamic characteristics and the …

Modelling Air Quality In An Aircraft Passenger Cabin Using Health Care Standards, Bert Silich

International Journal of Aviation, Aeronautics, and Aerospace

The interest in aerosol contamination of aircraft passenger cabins has increased since the onset of the COVID-19 pandemic. Mathematical models have been developed to help describe how an aerosol behaves in a closed space. The number of infectious particles inhaled is of scientific interest because it can be related to the risk of getting ill from a pathogen. The data required to calculate these results is often difficult to obtain in real world settings. In fact, particle inhalation details are not obtained in the day-to-day routine of a health care environment and are they not required to maintain safety. Hospital …

Effect Of Freestream Noise On Hypersonic Crossflow-Induced Boundary-Layer Transition, Andrew Bustard, Thomas J. Juliano, Harrison B. Yates, Mark Noftz, Joseph Jewell

Publications

Between the windward and leeward rays, boundary-layer transition on cones at angle of attack in hypersonic flow is dominated by the crossflow instability [1, 2], wherein stationary and/or traveling crossflow vortices develop and can breakdown into turbulence [3]. Stationary crossflow modes are caused by surface roughness or any other steady forcing and produce disturbances that are fixed in place on the surface [3–6]. Stationary vortices create a generalized inflection point in the velocity profile that is inviscidly unstable [7]. This distorted mean flow develops secondary instabilities, whose growth and breakdown is one path to turbulence [8–10]. Traveling crossflow modes are …

Experimental Study Of Wall Bounded Harbor Seal Whisker Inspired Pin Geometries, Anish Prasad, Mark Ricklick

Publications

Conventional cylindrical/elliptical pins are one of the most widely used geometries in convection cooling systems and are used in the internal cooling of gas turbine blades and other applications, as they promote better heat transfer at the expense of large pressure losses and unsteadiness in the flow. The need to reduce pressure drop and maintain the heat transfer rates are a pressing requirement for a variety of industries to improve their cooling efficiency. One such prominent field of research is conducted in optimizing the design of pin geometries. In this study, a harbor seal whisker inspired geometry is being studied …

Numerical Simulation Of A Cryogenic Spray, Neel Kishorkumar Shah

Doctoral Dissertations and Master's Theses

Cryogenic sprays have many applications in modern engineering. Cooling of electronic equipment subject to high heat flows, surgical ablation of gastrointestinal mucosae or orbital maneuvering are a few examples of their versatility. However, the atomization of a cryogenic liquid is a complex process. During such an event, aerodynamic effects associated with secondary atomization are further affected by thermodynamic flashing. A better understanding of the characteristics of cryogenic sprays is then necessary to allow for improved design and optimization in applications. The overarching objective of this study is to document such characteristics. The numerical simulation was performed over cryogenic nitrogen spray …

Reduced-Order Dynamic Modeling And Robust Nonlinear Control Of Fluid Flow Velocity Fields, Anu Kossery Jayaprakash, William Mackunis, Vladimir Golubev, Oksana Stalnov

Publications

A robust nonlinear control method is developed for fluid flow velocity tracking, which formally addresses the inherent challenges in practical implementation of closed-loop active flow control systems. A key challenge being addressed here is flow control design to compensate for model parameter variations that can arise from actuator perturbations. The control design is based on a detailed reduced-order model of the actuated flow dynamics, which is rigorously derived to incorporate the inherent time-varying uncertainty in the both the model parameters and the actuator dynamics. To the best of the authors’ knowledge, this is the first robust nonlinear closed-loop active flow …

Analyzing The Effect Of Delta Airlines' Fleet Upgrade On Operations At Atlanta-Hartsfield Jackson International Airport, Carlos Alberto Castro, Shlok Misra

Publications

Commercial aviation has seen a growth in terms of passengers traveled and flights operated in the past decade (BTS, 2020). To cope up with this growth, airlines adopt various strategies such as network expansion and fleet upgrades. Airlines adopt fleet upgrade strategies to modernize their fleet, reduce costs, expand network coverage, and improve customer loyalty and experience. Research suggests that change in wake turbulence categorization and aircraft performance can directly impact the movements and delays at an airport. For this study, Delta Airline's fleet upgrade program and its effect on operating parameters at Atlanta-Hartsfield Jackson International Airport were analyzed. The …

Assessment Of Conventional And Air-Jet Wheel Deflectors For Drag Reduction Of The Drivaer Model, Sandra K. S. Boetcher, Kaloki L. Nabutola

Publications

Aerodynamic drag is a large resistance force to vehicle motion, particularly at highway speeds. Conventional wheel deflectors were designed to reduce the wheel drag and, consequently, the overall vehicle drag; however, they may actually be detrimental to vehicle aerodynamics in modern designs. In the present study, computational fluid dynamics simulations were conducted on the notchback DrivAer model—a simplified, yet realistic, open-source vehicle model that incorporates features of a modern passenger vehicle. Conventional and air-jet wheel deflectors upstream of the front wheels were introduced to assess the effect of underbody-flow deflection on the vehicle drag. Conventional wheel-deflector designs with varying heights …

Background Flow Influence On Impulsive Jet-Driven Micro Droplet Dispersal, Vaishak Thiruvenkitam

Doctoral Dissertations and Master's Theses

Accurately predicting the airborne spread of infectious diseases is crucial in controlling the COVID­19 pandemic today. Studies have shown the spread of expiratory droplets depends on ambient thermodynamic conditions and flow properties of the jet emitted by the activity. However, the droplet spread in conditions of background flow is not yet comprehensively understood. This study uses the Eulerian­-Lagrangian model with k−ω turbulence modelling to simulate spread of particles and study the factors affecting it in a closed environment with a background flow. Respiratory activities are modeled as a non-­isothermal jet of air with droplets suspended in them in a predetermined …