Aerodynamics and Fluid Mechanics Commons^™

Thermal Management With Supercritical Carbon Dioxide Under Extreme Applications, Devon Hardy

Doctoral Dissertations and Master's Theses

A unique challenge in thermal system design is minimizing the power required to operate cooling systems while maintaining effective heat removal. Traditional cooling systems utilize single-phase fluids where the heat transfer mechanisms are well understood. To meet a variety of cooling demands, a range of technologies are available, including microchannel forced convection, jet impingement, porous media, nanofluids, pin fin arrays, and film cooling, each offering distinct advantages and limitations. While the performance of single- or two-phase cooling systems are generally predictable, in extreme thermal environments, new cooling solutions are needed to improve overall system efficiency and reliability.

Supercritical fluids, particularly …

Propeller Noise Prediction Of An Urban Air Mobility Vehicle In Urban Environment, Jie Hua

Doctoral Dissertations and Master's Theses

Urban Air Mobility (UAM) vehicles operate in complex, unsteady aerodynamic environments where wake interactions, gust and turbulence significantly affect both performance and noise generation. Understanding these mechanisms is critical for developing quieter and more efficient eVTOL systems that meet future community noise and certification requirements. This dissertation focuses on the high-fidelity numerical investigation of propeller noise in three representative unsteady loading scenarios: (i) transition (tilt) flight, (ii) edgewise inflow, and (iii) wake–propeller interaction. Each case emphasizes different physical mechanisms that dominate noise generation in UAM operations. Hybrid turbulence-resolving approaches—Detached Eddy Simulation (DES) and Delayed Detached Eddy Simulation (DDES)—are coupled with …

Numerical Study On Flow Separation And Performance Characteristics Of Slot Nozzle, Chase Charpentier

Doctoral Dissertations and Master's Theses

The altitude compensating nozzle (ACN) is a type of rocket nozzle or engine that tries to minimize the negative effects of overexpansion at low altitudes. There are many forms of ACN's but most of them are heavier than traditional bell nozzles, alter the geometry of the nozzle, which requires extensive research into optimizing the new geometry, or require complex systems that can lead to structural, heating, or material problems. Out of the ACN's, the slot nozzle is a passive ACN that builds upon the bell nozzle and requires no additional weight or complex systems.

This slot nozzle is comprised of …

Perturbation Solution Of Air-Water Mixture For Jet Noise Reduction, Juan Felipe Uribe Cifuentes

Doctoral Dissertations and Master's Theses

This work investigates passive jet-noise mitigation using externally positioned air–water curtains that attenuate radiated sound without altering the underlying jet dynamics. Two classes of multiphase media are examined: a gaseous carrier phase containing dispersed liquid droplets, and a liquid carrier phase containing entrained air bubbles. For both systems, suspended and dispersed regimes are represented through a generalized perturbation formulation derived from the volume-averaged multiphase equations, incorporating finite volume fractions, interphase momentum coupling, and slip between phases. Analytical and numerical solutions demonstrate that acoustic attenuation is primarily governed by dispersed-phase diameter, volume fraction, and excitation frequency, with additional sensitivity to phase-interaction …

Exploration Of Physics-Informed Grid Generation Technique For Wall-Modeled Les Using Eagle3d, Dominic Schneider

Doctoral Dissertations and Master's Theses

Wall-Modeled Large Eddy Simulation (WMLES) is an area of interest due to its ability to lower computational costs of LES. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required. A novel technique for generating a lean, physics based WMLES grid is described.

The technique utilizes a RANS solution to extract turbulence information, user-specified values related to resolution of turbulent energy levels, acoustics waves, and shock waves, to generate a point cloud for producing a lean WMLES grid with in-house …

Active Measurement Of A Micron-Order Gap Under High-Speed And High-Temperature Conditions, Andrew Becker

Doctoral Dissertations and Master's Theses

The hypersonic regime poses numerous challenges that researchers face in the development of hypersonic flight vehicles. Due to their excellent thermomechanical properties, ultra-high-temperature ceramics (UHTCs) have risen as a promising solution to act as a protective barrier between the harsh environment and surface materials of these flight bodies. The mechanical operation of a portable hypersonic simulation device was developed in-house and tested at Argonne National Laboratories (ANL) to gather in-situ material response of prospective UHTC samples when exposed to a hypersonic regime. An edge detection-based algorithm was developed and used in LabVIEW to monitor the health and operation of the …

High-Fidelity Modeling Of Evtol Rotor Unsteady Aerodynamic And Aeroacoustic Response To Time-Harmonic Gust, Vadim Voropayev

Doctoral Dissertations and Master's Theses

The rapid emergence of Urban Air Mobility (UAM) demands accurate prediction and mitigation of noise generated by electric vertical take-off and landing (eVTOL) aircraft operating in complex urban environments. Among the various noise sources, the aerodynamic and acoustic response of rotors to unsteady inflow represents a major uncertainty in community-noise assessment and certification. This thesis investigates the aerodynamic and aeroacoustic behavior of a representative eVTOL rotor subjected to time-harmonic inflow disturbances, providing a detailed numerical framework to quantify how periodic gusts influence rotor performance, unsteady loading, and sound radiation.

The study employs a three-stage computational methodology using the open-source solver …

Design Of A Fan-Based Test Stand For Evaluating Multicopter Handling In Turbulent Flow, Salim Roig

Doctoral Dissertations and Master's Theses

With the innovation of eVTOL rotorcraft the need to analyze how turbulence-induced disturbances from orthogonal flow affect various rotorcraft configurations outside of simulations have grown significantly. To investigate the behavior of this type of flow and how it interacts with various rotorcraft configurations, a turbulent inducing test stand was designed and constructed. The test stand will have two walls of computer fans arranged in an L-shape frame, creating wind gusts that simulate the non-linear turbulent wind experienced by eVTOL. This also aids the Eagle Flight Research Center (EFRC) in their efforts to better understand how disturbances affect the handling qualities …

Implementing A 5-Dimensional Tabulated Conditional Moment Closure Model With Scalar Dissipation Rate For Scramjet Combustion, Alp Tuztas, Scott Montgomery Martin, Carlos A. Velez

Discovery Day - Daytona Beach

The growing interest in Scramjets for achieving sustained hypersonic flight has given rise to numerous computational models to obtain solutions as close as possible to experimental data, assisting with making the design process of modern Scramjet’s with different propellants and cavity designs less costly. However, Scramjet engines pose significant challenges for computational modelling due to the need of accounting for large- and small-scale turbulences but also solving turbulence chemistry interactions in compressible flow regimes. A promising approach has been through using high-fidelity turbulence-combustion models which greatly assist with capturing detailed chemistry, account for small scale turbulence and the complex flow …

Self-Regulated Thermal Management With Shape-Memory Alloy Torsional Tubes, Paula Sanjuan Espejo

Doctoral Dissertations and Master's Theses

The need for dynamic thermal management that adapts to varying system needs and requirements is a growing topic of interest in different engineering disciplines, most prominently aerospace and electronics. This demand for improved thermal management systems comes from the general increase of system efficiencies leading to an increase in component energy density. Shape-memory alloy actuators, which respond with a mechanical shape recovery to variations in temperature, can be used as self-regulated thermal management actuators that are able to respond to environmental thermal changes autonomously. In this dissertation, modeling and experimental analysis of a two-way shape-memory effect trained SMA torsional tube …

The Interaction Of A Transient Forward Axial Disturbance Flow With A Rotor, Zhuorui Li

Doctoral Dissertations and Master's Theses

This research presents an in-depth investigation of the aeroacoustic characteristics of a scaled-down Joby Aviation rotor, focusing on its performance under realistic conditions for urban air mobility (UAM). Utilizing a high-fidelity numerical simulation approach that combines Large-Eddy Simulation (LES) and Unsteady Reynolds-Averaged Navier-Stokes (URANS) models, the study effectively captures the complex aerodynamic and acoustic interactions inherent in rotor operations. Validation of the numerical framework was achieved through comprehensive comparisons with available experimental data, demonstrating a high level of accuracy in predicting both aerodynamic performance metrics, including thrust and torque, as well as acoustic emissions. The simulation revealed significant impacts resulting …

Aeroacoustics Applications To Jets And Rotors, Michael Marques G.

Doctoral Dissertations and Master's Theses

Aeroacoustics plays a critical role in the advancement of propulsion technologies for both conventional and emerging aerial systems. This dissertation investigates two key topics: noise suppression in supersonic rectangular jets and rotor noise characterization in hover and ground effect. Using high-fidelity numerical simulations and theoretical analyses, this research aims to develop effective noise mitigation strategies and improve predictive methodologies.

The first part of this study focuses on the reduction of noise in supersonic rectangular jets through active control techniques. A novel approach utilizing unsteady microjet actuation at the nozzle lip is explored to disrupt the formation of large-scale turbulent structures …

Experimental Investigation Of Heat Transfer To Tightly Packed Cylinder Arrays, Cameron M. Sexsmith

Doctoral Dissertations and Master's Theses

With the increased emphasis on the development of hybrid electric aircraft and other electric driven vehicles, the thermal demand on batteries is increasing. Unique to the aviation sector is the combined need of high battery thermal loads and a light-weight thermal management system. A proposed configuration is an array of batteries directly cooled with a dielectric coolant. The knowledge of heat transfer characteristics of battery cooling is becoming an ever pressing issue due to the need to optimize volume and mass in a safe manner. Tighter spacings between batteries provide higher pack densities, however, at the cost of increased cooling …

Exploring A Novel Adaptive Mesh Refinement Strategy For High-Speed Cfd, Arjun Jaishankar Vedam

Doctoral Dissertations and Master's Theses

Adaptive Mesh Refinement (AMR) techniques to efficiently and robustly achieve grid independent solutions on multi-element unstructured grids is a topic of practical interest within the CFD community.

The current effort focuses on the efficiency of a novel Adaptive Mesh Refinement (AMR) strategy that is developed and evaluated for transonic high-speed flows using Ansys Fluent. The algorithm for marking cells for adaptation is designed to systematically reduce local truncation errors based on the curvature of the primitive vector field. The algorithm for marking cells for adaptation is described in sufficient detail to be portable to other flow solvers that offer AMR. …

Investigation Of A Busemann Intake At Negative Angle Of Attack, Mark E. Noftz, Andrew N. Bustard, Nicholas J. Bisek, Thomas J. Juliano, Joseph S. Jewell

Publications

A high-speed, shape-transitioned, inward-turning intake was tested in Purdue’s Boeing/AFOSR Mach 6 Quiet Tunnel. The inlet model, called the Indiana Inlet (INlet), had a total contraction ratio of 4.68:1 and a design point of Mach 6 at 0° angle of attack. The model was outfitted with a suite of high-frequency pressure transducers, and the external flowfield was imaged with high-speed schlieren photography. The INlet was tested under low freestream disturbance levels for a variety of freestream unit Reynolds numbers and at-4° angle of attack. An unsteady shockwave near the leading edge of the inlet forebody, indicative of boundary layer separation, …

Heat Transfer In Tightly Packed Cylinder Arrays, Martin Kovachev

Doctoral Dissertations and Master's Theses

Cylindrical arrays with a cross flow are commonly used for heat transfer augmentation within an internal channel. In most applications, the cylinders have a spacing of over 2 diameters (2D) between their center points in both the lateral and downstream directions. One option for battery thermal management in hybrid/electric aviation is to use cylindrical batteries packed in arrays with an applied cross flow. In the context of aviation, it is important to maximize space and weight savings. Tightly packing these cylinder arrays with a spacing of under 2D in both directions would save on both of these yet have not …

Dynamic Estimation Of Large-Scale Flow Events In Open Cavity Flows, Alexandre Mota

Doctoral Dissertations and Master's Theses

Flow over an open cavity has a dynamically complex flowfield, generating pressure fluctuations that can amplify shear stress and cause structural damage to the stores within it and the aircraft as a whole. These pressure loads are linked to large-scale resonant shear layer phenomena. Consequently, it is crucial to establish this link by characterizing the large-scale flow events conditional upon pressure measurements to improve the prediction and control of the detrimental pressure fluctuations. In this study, a link between the pressure measurements (to control) and large-scale shear layer events (to actuate) will be established using a combination of two data-driven …

Contributions To The Understanding Of Turbulent Boundary Layers Over Curved Walls, Nicholas Zhu

Doctoral Dissertations and Master's Theses

A wind tunnel campaign was conducted to investigate the DARPA Suboff boundary layer. To emphasize the axisymmetric boundary layer, the generic submarine model's sail, appendages, and propeller were omitted. The study focused on the afterbody from 70–95% of the model length to examine the concurrent pressure gradient and wall curvature effects, which are commonplace in engineering. Three particle image velocimetry (PIV) configurations were employed to measure the boundary layer in detail: one spanned the entire afterbody, another had narrow strips sampled at 16 kHz, and the third used two simultaneous orthogonal measurement planes. Considerable effort was made to reduce the …

Heat Transfer To Arrays Of Oscillating Impingement Jets, Alex Q. Clay

Doctoral Dissertations and Master's Theses

In gas turbine engines, the desire to increase turbine entry temperatures has become more relevant in order to increase engine efficiency. However, materials used in these engines can only withstand temperatures that are so high. Because of this, the ability to cool hot section components will always limit operating temperatures. Impingement cooling jets have become a common way of cooling due to the high rates of heat transfer that can be achieved. However, previous research has shown that the interaction of impingement jets with cylinder wake can improve the intensity and uniformity of heat transfer. The goal of this study …

Bi-Modal Excitation Of A Supersonic Rectangular Jet, Benjamin Malczewski

Doctoral Dissertations and Master's Theses

This work addresses the issue of supersonic rectangular jet noise via bi-modal excitation. A Mach 1.5 heated rectangular jet with a 2:1 aspect ratio is considered. Theoretical work is presented in which a Reduced-Order Model (ROM) is used in conjunction with the Linearized Euler Equations to predict the nonlinear growth and decay of various frequencies due to the interaction between harmonically related modes and the mean flow. Scope is limited to a symmetric disturbance. The case of no interaction is used to help identify a dominant coherent structure, referred to as “f”. For the symmetric disturbance, a Strouhal number of …

Optimization Of A Plate Beam System For Energy Harvesting Using A Piezoelectric Material, Jose Manuel Almendros Espantaleon

Doctoral Dissertations and Master's Theses

With a continuously growing demand for power, driven by the need to reduce our environmental footprint, this research provides an examination of the potential of energy harvesting with smart materials technology and its practical applications. The energy harvesting system considered here works on generating energy through vibrations of a piezoelectric material beam which will undergo sustained vibrations due to flow of air over its surface. It is assumed that sustained limit cycle oscillations of this system will occur at the flutter velocity. This research creates an optimization framework to obtain the best values of parameters that will result in the …

Analysis Of Wingtip Vortex Structure Generated By Bio-Inspired Winglets, D'Zahn A. Smith

Doctoral Dissertations and Master's Theses

Bio-inspired winglets were studied with the goal of better understanding the structure of the wingtip vortices they generate. Measurements of the tip vortex were previously carried out using stereoscopic particle image velocimetry (sPIV). The bio-inspired winglet was tested on a rectangular NACA 0012 wing section at a 5-degree angle of attack and at a chord Reynolds number of 900,000. Velocity field measurements were recorded at 0.7 and 2 chord lengths aft of the wing’s trailing edge. Compared to the wing with no attachment and a traditional blended winglet, the bio-inspired winglet’s vortex exhibited significantly less intense flow field properties. These …

Characterization And Analysis Of Supersonic Flow Through De Laval Nozzles At Varied Design Conditions, Sarah Baird

Doctoral Dissertations and Master's Theses

A combined numerical and experimental investigation of supersonic planar nozzles under different design conditions has been conducted. Supersonic planar nozzles are common geometries observed in supersonic wind tunnels and aircraft or rocket engines. For the important role they play in wind tunnel testing and aircraft propulsion, it is important to conduct a thorough numerical and experimental study to characterize their performance at different operating conditions. In this study, a de Laval nozzle was scanned to extract its contours and subsequently modeled to compare analytical and numerical performance expectations under design and off-design conditions. The nozzle was then installed in a …

Modeling Of Rotor Wake Vortex Dynamics And Interactions In Non-Homogenous Vertiport Environments, Garrison P. Shaw

Doctoral Dissertations and Master's Theses

The current research serves to analyze and study the effects ground forces can have on the thrust performance of a propeller in multiple different configurations. The current research utilizes an open source Computational Fluid Dynamics (CFD) software known as OpenFOAM to generate calculate and visualize these runs. The model used for this experiment is a hybrid model that employs both a Unsteady Reynolds-Averaged Navier-Stokes (URANS) and a detached eddy simulation using a hybrid Large Eddy Simulation (LES) via a KomegaSSTDDES model. This model serves to save computational time as well as allow for accurate results. The three cases run are …

Development Of Eagle3d Solver For Wall Modeled Les Of Transonic Flows, Spencer Moore

Doctoral Dissertations and Master's Theses

Wall modeled Large Eddy Simulation (LES) is an area of interest due to its ability to lower computational costs of LES simulation. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required to get results. A case described by an axisymmetric transonic bump is explored utilizing the Embry-Riddle Aeronautical Universities in house unstructured finite volume multi-element CFD code, Eagle3D. Eagle3D, has been brought to the state of the art and validated against current research using this transonic bump case as …

Development Of On-The-Fly Quasi-Steady State Approximation For Chemical Kinetics In Cfd, Abhinav Balamurugan

Doctoral Dissertations and Master's Theses

This study analyzes the feasibility of On-The-Fly Quasi-Steady-State Approximation (OTF-QSSA) application for solving chemical kinetics within Computational Fluid Dynamics (CFD) simulations, aiming to reduce the computational demand of detailed mechanisms. An algorithm that dynamically identifies and designates Quasi-Steady-State (QSS) species at specific grid locations and instances during the simulation was developed. With this information, our method pseudo-delays the advancement of concentrations for these QSS species—effectively setting their rate of concentration change to zero for a set number iteration before updating using the detailed mechanism and thereby omitting the computationally intensive processes typically required for their calculation during those skipped iteration. …

Numerical Study In Wind Energy Extraction From Controlled Limit-Cycle Oscillations In Modified Glauert Airfoil, Ethan L. Deweese

Doctoral Dissertations and Master's Theses

Typically, wind energy harvesting technology employs wind turbines. Towards the goal of meeting increasing energy needs with renewable energy sources a novel wind energy harvesting scheme is considered, utilizing a modified Glauert (MG) airfoil experiencing aeroelastic limit cycle oscillation (LCO) from which energy may be extracted. Synthetic jet actuators (SJA)s are used along with the unique geometry of the MG airfoil to control flow separation and amplify the LCO and energy generation potential of the system. The discussed wind energy harvesting scheme could provide flexibility in allowing installations previously unsuitable to wind turbines due to geometric or low wind velocity …

Mitigating Engine Unstart In Scramjets With Porous Bleeders, Ryan Lindley

Doctoral Dissertations and Master's Theses

The effectiveness of porous bleeders in mitigating unstart phenomena and enhancing isolator effectiveness in a hypersonic scramjet was investigated. Through computational fluid dynamics simulations, the impact of porous bleeder design parameters such as pressure jump coefficient and bleeder size on isolator effectiveness and unstart prevention was evaluated. Results indicated that porous bleeders delayed flow separation and reduced adverse pressure gradients, thereby enhancing isolator performance. Additionally, porous bleeders demonstrated promising capabilities in preventing full unstart events and mitigating oscillatory unstart phenomena.

Conceptual Design Methodology For The Fan-In-Wing Vtol Aircraft, Brock Steinfeldt

Doctoral Dissertations and Master's Theses

The Fan-In-Wing (FIW) aircraft concept is one of the most compelling solutions for missions demanding jet-like cruise speeds and Vertical TakeOff and Landing (VTOL) capability. However, despite years of interest and documented improvements in lift-fan technology, there exists little in the way of an adequate theory for conceptual design of a fan-in-wing aircraft. To address this issue, a general conceptual design methodology has been developed as a source of guidance for the FIW designer. Through this work, the top-level requirements ranking the fan-in-wing concept above other VTOL aircraft have been defined, while a cross-comparison between the FIW concept and conventional …

Adaptive Control Of An Aeroelastic System For Active Flutter Suppression And Disturbance Rejection, Patrick Sterling Downs

Doctoral Dissertations and Master's Theses

The future of aircraft design strives for lighter weight, more aerodynamically efficient structures. These improvements may come with the drawback of increased structural flexibility and elevated aeroelastic effects, often resulting in a lower flutter speed. This motivates the implementation of advanced control methods to control aeroelastic systems over a range of flight conditions, suppress and delay the onset of flutter, and compensate for disturbances, actuator dynamics, and unmodeled nonlinear dynamics.

This dissertation first develops a novel method for constructing time-domain simulation models of two and three-dimensional aeroelastic systems, resulting in models that are suitable for the implementation of state-space control …