Aerodynamics and Fluid Mechanics Commons^™

Low Reynolds Number Numerical Simulation Of The Aerodynamic Coefficients Of A 3d Wing, Khurshid Malik, Waqar Asrar, Erwin Sulaeman

International Journal of Aviation, Aeronautics, and Aerospace

A low Reynolds number, three-dimensional CFD analysis is carried out for a finite flat plate wing using the commercial CFD code STAR CCM+. The six-aerodynamic force and moment components C_L, C_D, C_M, C_N, C_l, C_Y and their derivatives are computed at a Reynolds numbers of 3x10⁵ by varying the pitch, roll and yaw angles about the quarter chord point. The computed results have been validated with experimental aerodynamic balance data when possible. The results indicate that roll and yaw angle affect the aerodynamic coefficients of the flat plate …

Base Pressure Control Using Micro-Jets In Supersonic Flow Regimes, Vigneshvaran Sethuraman, Sher Afghan Khan

International Journal of Aviation, Aeronautics, and Aerospace

Base pressure plays a vital role in aerospace-related applications and its control is essential in reduction of drag and improving fuel consumption. Low pressure at the base of Rockets, Missiles, bombs and shells are a very common problem happening at transonic and supersonic speeds. In most of the cases there is a significant dip in pressure at the base region which will have implications on the design of aerospace vehicles. This paper presents an experimental investigation carried out for flow control at supersonic regimes. Experiments were conducted to measure the base pressure in the base region and wall pressure distribution …

Aerodynamic And Performance Analysis Of A Morphing Helicopter Rotor System, Vinay Gopal Krishnan

Doctoral Dissertations and Master's Theses

The purpose of this study was to investigate the effect of rotor morphing, specifically variable rotor speed and variable blade twist, on various parameters such as the distribution of angle of attack, lift, power, thrust and/or other metrics describing the performance of a helicopter rotor. A MATLAB based blade element theory model was developed and executed for different flight conditions. The model was validated against the flight test data of a UH-60. Effects on power, lift to drag ratio and rotor drag from variations in blade twist, rotor speed, rotor radius and blade chord was analyzed. Morphing cases were applied …

Implementation And Verification Of A Synthetic Eddy Method (Sem) In The Eagle3d Compressible Flow Solver, Patrick Kopper

Doctoral Dissertations and Master's Theses

The objective of this thesis is to implement and evaluate a Synthetic Eddy Method (SEM) into the Eagle3D compressible flow solver. Both the ability of Eagle3D to resolve unsteady turbulent ow field and capability of the SEM to reproduce given Reynolds stress profiles to start realistic turbulent behavior are verified using common academic cases. Eagle3D is a Computational Fluid Dynamics (CFD) solver using a novel combination of a Bounded Central Differencing (BCD) scheme with Weighted Essentially Non-Oscillatory (WENO) approximation to reduce numerical dissipation. SEM is a modern synthetic turbulence method able to reproduce an arbitrary Reynolds stresses specification on discretionary …

Blended Wing Body Propulsion System Design, Parth Kumar, Adeel Khalid

International Journal of Aviation, Aeronautics, and Aerospace

This research paper focuses on the optimization of the propulsion system of a blended wing body design. Two different aspects of the design, the engine placement and count, and the engine itself, are investigated. The preliminary wing of the BWB is created through aerodynamic analysis, and is kept as a constant over the different propulsion system configurations. The engine parameters are first investigated. Equations are derived to express takeoff distance and climb rate as a function of engine sea level thrust, cruise thrust, and the number of engines. Nearly 150 different engine models, in BWB configurations of 2, 3, 4, …

Wingtip Vortex Alleviation Using A Reverse Delta Type Add-On Device, Afaq Altaf

International Journal of Aviation, Aeronautics, and Aerospace

The result of interactions of a wingtip vortex of a half-span wing and vortices generated by a slender reverse delta type add-on device were studied using Particle Image Velocimetry in a closed-loop low-speed wind tunnel. Characteristics of the vortex interactions produced downstream in planes perpendicular to the free stream direction at a mean chord-based Reynolds number, Re_c = 2.75×10⁵, are explored in this work. The study reveals that the reverse delta type add-on device considerably reduces the tangential velocity, vorticity and circulation magnitude of the resultant vortex by up to 79.6%, 85.6% and 48.7%, respectively. It was …

Effect Of Boundary-Layer Tripping On Turbulence Generation And Trailing-Edge Noise In Transitional Airfoils, James Benjamin Lewis

Doctoral Dissertations and Master's Theses

The need arises for developing quiet aircraft and silent Unmanned Aerial Vehicles (UAVs) to minimize the environmental effects as well as for stealth missions. We focus here on attempting to directly predict the noise associated with airframe by considering a single isolated airfoil. Developing an ability to directly predict the radiated noise and how it is generated is a first step for passive or active control of the generated noise. We choose herein a NACA0012 airfoil and specific flow condition to test whether we can directly predict the sound in accordance with the corresponding experimental data identified in the Benchmark …

Literature Review: Biomimetic And Conventional Aircraft Wing Tips, Naseeb Ahmed Siddiqui, Waqar Asrar, Erwin Sulaeman

International Journal of Aviation, Aeronautics, and Aerospace

This paper is an attempt to summarize the effect of wing tip devices employed by birds, as well as aeronautical engineers in the past to improve the performance characteristics of aircraft. The focus is on reduction of the induced drag or drag due to lift also known as inviscid drag. This paper will provide an insight on both biomimetic and conventional wing tip approaches to reduce the induced drag. Prior analysis and experiments on the aerodynamics of airplane performance due to both these separate studies have been discussed. The needs of the industry and their past inventions have been described …

Comparison Of Rans Modeling To Dual-Plane Piv Measurements Of The Turbulent Tip Vortex Trailed From A Hovering Rotor, Zachary Lietzau

Doctoral Dissertations and Master's Theses

Numerical simulations using the Reynolds-Averaged Navier-Stokes (RANS) equations were conducted to study the development and turbulent decay of the tip vortices in the wake produced by a hovering rotor. The computational results were compared to detailed, dual plane Particle Image Velocimetry (PIV) measurements of a turbulent tip vortex trailed from a single-bladed rotor. The work investigated both the required mesh resolution and most suitable turbulence closure models with rotational/curvature corrections by assessing their predictions of the tip vortex properties and the overall physical nature of the rotor wake. It was found that even when using a higher-order accurate central differencing …

Extended Surface Heat Transfer Coefficients Via Endwall Temperature Measurements, Yogesh Pai

Doctoral Dissertations and Master's Theses

Short pins are used for internal cooling of the trailing edge in a gas turbine blade. A novel method is described in this thesis which helps in simplifying the experimental process used to obtain average heat transfer data on the pin surface, at the expense of additional post processing complexity. The method is based on a unique, analytical solution of the longitudinal conduction equation with internal heat generation, allowing computation of heat transfer rates via pin base temperature measurements via Temperature Sensitive Paint, or similar non-intrusive methods. Verification of this method is done with comparisons to the solution of infinite …

In-House Fabrication Of Temperature Sensitive Paint For Turbine Cooling Research, Mayur D. Patel, Mark A. Ricklick

Beyond: Undergraduate Research Journal

The Temperature Sensitive Paint (TSP) is a widely used method in measuring and visualizing flow separation and heat transfer. Compared to the cost and time consumption needed for methods such as pitot tubes, temperature sensitive paint is a cheaper alternative. Due to high usage in College of Engineering research projects, it was determined that in house fabrication of temperature sensitive paint would reduce time and cost limitations. For initial stages, literature research was performed to determine the recipe of intensity based TSP with luminophore and polymer binder that operated optimum at temperatures from 0-100°C. Europium III thenoyltrifluoroacetonate was determined to …

An Archival Analysis Of Stall Warning System Effectiveness During Airborne Icing Encounters, John Michael Maris

Doctoral Dissertations and Master's Theses

An archival study was conducted to determine the influence of stall warning system performance on aircrew decision-making outcomes during airborne icing encounters. A Conservative Icing Response Bias (CIRB) model was developed to explain the historical variability in aircrew performance in the face of airframe icing. The model combined Bayes’ Theorem with Signal Detection Theory (SDT) concepts to yield testable predictions that were evaluated using a Binary Logistic Regression (BLR) multivariate technique applied to two archives: the NASA Aviation Safety Reporting System (ASRS) incident database, and the National Transportation Safety Board (NTSB) accident databases, both covering the period January 1, 1988 …

Multi-Stage Axial Compressor With Counter-Rotation, Vinod Gehlot, Magdy S. Attia, Divyam Garg

Publications

A multi-stage axial compressor incorporating a counter-rotational movement is provided with a series of rotors mounted along and driven by a driveshaft, and a geared counter-rotating outer casing. A planetary gear system is assembled along a static casing, which can be assembled as a forward or aft casing for the compressor. The bearings of the planetary gear system typically will be aligned concentrically with a center rotor drum assembly mounted along the single driveshaft. The counter-rotating drum assembly will be assembled over the rotor drum assembly and will be engaged by the forward and aft casings so as to provide …

Effect Of Slot Span On Wing Performance, Juan F. Granizo

Doctoral Dissertations and Master's Theses

This report presents new numerically-derived correlations to estimate the aerodynamic properties of a three-dimensional wing that features a partial to full span fixed slot. Fixed slots have been thoroughly studied in the past with regards to their operation and the relation between slot geometry and wing performance. There have also been many studies on the advantages and disadvantages of tip-slotted wings and the comparison between these and full-slotted wings. Up to this point however, a study on the effects of slot span on wing performance has not been performed. Effect of slot span on wing performance is evaluated in an …

Effect Of Flow-Acoustic Resonant Interactions On Aerodynamic Response Of Transitional Airfoils, Joseph Hayden

Doctoral Dissertations and Master's Theses

A high-accuracy numerical study is conducted to examine the impact of flow-acoustic resonant interactions on the aerodynamic response of symmetric and cambered airfoils in the realistic transitional flow regimes with Rec=140,000 and M=0.0465 as well as the low Reynolds number flow regime with Rec=10,000 and M=0.2. The symmetric NACA-0012 and the cambered SD7003 airfoils are investigated at various angles of attack that have been found previously to include both the tone and no-tone producing regimes, with specific focus on the aerodynamic lift response. Additional simulations are conducted with a low-intensity synthetic turbulence introduced upstream of the airfoils in order to …

Turbulence Control In Wall Jets, Jonathan Latim

Doctoral Dissertations and Master's Theses

The turbulent boundary layer has been the focus of many studies over the last century or so due to its engineering significance. Recent studies have shown that the turbulent boundary layer encapsulates extremely energetic large-scale structures which play a much more significant role in its dynamics than has been previously thought. Further, these large scales amplitude and frequency modulate the finer scales of turbulence. This offers a path to control wall turbulence by controlling the large-scales of the flow. The focus of this thesis is to establish ways to manipulate the energy of the large-scale structures in a model turbulent …

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

A Computer Program For The Coupled Implementation Of Meanline And Throughflow Methods To Simplify The Aerodynamic Design Of Multistage Axial Compressors, Alexander V. Rozendaal

Doctoral Dissertations and Master's Theses

A computer program capable of simplifying the preliminary aerodynamic design process of multistage axial compressors has been developed. This interactive design tool, named C-STAAC, combines the Meanline and Throughflow analysis capabilities of two independent compressor design codes to form one standalone system. The program greatly improves the efficiency of the Preliminary-to-Throughflow stages of compressor design by providing fully coupled interaction between the two platforms. The result enables the user to produce stacked airfoil geometry from only a handful of initial input parameters.

The program additionally offers a wide selection of pre- and post-processing capabilities that were not previously available with …

Heat Transfer Analysis Of An Oblique Jet Impingement Cooling On Cmc Rough Surface, Karthik Krishna

Doctoral Dissertations and Master's Theses

A Ceramic Matrix Composite is high strength and high temperature capability composite, utilized in components like heat shield of space vehicles, flame holders and disc brakes. To be used in both static and dynamic components of a future gas turbine engine and even with high temperature capabilities of these CMC components, convection cooling will still likely be required. The surface of the CMC varies significantly from traditional super-alloy used in a modern engine, with large level of roughness and significant three-dimensional waviness. These complex features will impact the behavior of the near wall flows, and affect the heat transfer rates …

Impact Of A Reverse Delta Type Add-On Device On The Flap-Tip Vortex Of A Wing, Afaq Altaf, Tan Boon Thong, Ashraf Ali Omar, Waqar Asrar

International Journal of Aviation, Aeronautics, and Aerospace

The effect of interactions of vortices produced by an outboard flap-tip of a half-span wing (NACA 23012 in landing configuration) and a slender reverse delta type add-on device, placed in the proximity of the outboard flap-tip, on the upper surface of the half-span wing is investigated using Particle Image Velocimetry in a closed loop low speed wind tunnel. Specifically the characteristics of the vortex interactions generated downstream in planes perpendicular to the free stream direction and their dependence on angles of attack at a chord-based Reynolds number of Re_c=2.75×10⁵ have been determined. It was found that the …

Computational Investigation Of Impingement Cooling For Regeneratively Cooled Rocket Nozzles, Bianca A. De Angelo

Doctoral Dissertations and Master's Theses

Jet impingement cooling is an internal cooling configuration used in the thermal management of temperature sensitive systems. With rocket engine combustion temperatures rising as high as 3600 K, it is essential for a cooling method to be applied to ensure that the nozzle integrity can be maintained. Therefore, a novel heat transfer study is conducted to investigate if jet impingement cooling is feasible for a regenerative cooling rocket nozzle application. Regenerative cooling for liquid propellant rockets has been widely studied. However, to the best of the author’s knowledge, there is currently no literature describing this method in conjunction with impingement …

Fluidic Jet Turbulence Generators For Deflagration To Detonation Transition In Pulsed Detonation Combustors, Jarrett E. Lowe

Doctoral Dissertations and Master's Theses

The goal of this study is to establish the dominant flow structure required to effectively accelerate the turbulent deflagration flame front to detonation velocity in the shortest possible distance while using a single Jet in Cross Flow (JICF). Jets in crossflow, depending on orientation and momentum ratio, can induce two types of flow structures that propagate downstream; vortex filaments and turbulent eddies. Vortex flow structures are coherent rotating columns that can persist for a considerable distance before diffusing. Turbulent eddies are characterized as random fluctuations in flow velocity or small pockets of rotation. The test rig used for this study …

Study Of Hybrid Magneto-Active Propellant Management Device For Slosh Damping, Leander Paul

Doctoral Dissertations and Master's Theses

Sloshing of liquid upon the application of an external force is a natural phenomenon as the free surface is allowed to move without any constraints. Study of slosh is an ongoing research for many decades and many novel inventions in Propellant Management Devices (PMDs) such as the rigid baffles and elastomeric membranes have been implemented to counteract the free surface effect in both passive and active membrane known as Magneto-Active Propellant Management Device (MAPMD) to actively control the free surface effect and reduce fuel slosh is explored in this research. Being a hybrid membrane, it would initially offer passive resistance …

2d Aeroacoustic Analysis Of Flow In The Flame Trench, Meghan Pokorski

Doctoral Dissertations and Master's Theses

We present here a methodology for using the commercial software ANSYSFLUENT to predict the acoustic field associated with Space-Launch System (SLS). We consider a two-dimensional model of flame deflector, and flame trench. The ANSYS code is then used to simulate the internal flow. Both the steady state case is considered along with other cases where the inflow has a harmonic component. A Ffowcs-Williams Hawking (FWH) surface is then constructed within the computational domain to use the computed flow fluctuations to obtain the acoustic field. The acoustic data was then compared to the experimental data.

When using the ANSYS code for …

Lift & Drag Reductions On Iced Wings During Take Off And Landing With Unmanned Aerial Vehicles, Ian R. Mcandrew

Publications

This research paper addresses an novel problem that has not been addressed in detail for many decades. Ice formation on aircraft has procedures and protocols to deal with expected and actual problems. Complex modern aircraft are equipped with a variety of techniques to remove Ice formation on an aircraft, especially the wings. The introduction of Unmanned Aerial Vehicles has added an old problem, that of low speed and the lack of power to overcome losses in lift through ice formation. In this research the different types of Ice formation, how they combine and affect Lift and Drag are also addresses …

Direct Adaptive Control For Stability And Command Augmentation System Of An Air-Breathing Hypersonic Vehicle, Ron Aditya

Doctoral Dissertations and Master's Theses

In this paper we explore a Direct Adaptive Control scheme for stabilizing a non-linear, physics based model of the longitudinal dynamics for an air breathing hypersonic vehicle. The model, derived from first principles, captures the complex interactions between the propulsion system, aerodynamics, and structural dynamics. The linearized aircraft dynamics show unstable and non-minimum phase behavior. It also shows a strong short period coupling with the fuselage-bending mode. The value added by direct adaptive control and the theoretical requirements for stable convergent operation is displayed. One of the main benefits of the Directive Adaptive Control is that it can be implemented …

Aerodynamic Trade Study Of Compound Helicopter Concepts, Julian Roche

Doctoral Dissertations and Master's Theses

The relative performance attributes of compound helicopter concepts have been examined, including their potential for meeting the requirements of several challenging mission profiles. For each concept, which included lift and/or propulsive compounding, a suite of aerodynamic performance models was developed using energy methods. In the case of a lift-compounded concept, an aerodynamic model representing the force interaction effects of the main rotor wake with the wing was also developed. Models of a conventional helicopter and of a tiltrotor were implemented as well, and the results used as a datum for comparison. In each case, the predictive capabilities of the model …

Numerical Study Of Synthetic-Jet Actuation Effect On Airfoil Trailing Edge Noise, Marco Sansone

Doctoral Dissertations and Master's Theses

The current study conducts numerical simulations to assess the possibility of employing Synthetic Jet Actuators (SJAs) as active noise control devices for reduction of airfoil acoustic radiation. High-accuracy numerical efforts employ a sixth-order accurate Navier-Strokes solver implementing a low-pass filtering of poorly resolved high-frequency solution content to retain numerical accuracy and stability over the range of transitional flow regimes. In the adopted numerical procedure, the actuator is modeled without its resonator cavity through imposing a simple fluctuating-velocity boundary condition at the bottom orifice of the actuator. The orifice cavity with the properly defined boundary condition is embedded into the airfoil …

Book Review: High G Flight - Physiological Effects And Countermeasures, Stefan Kleinke

International Journal of Aviation, Aeronautics, and Aerospace

This review provides insight on the content and a review of the quality of the recent release of High G Flight - Physiological Effects and Countermeasures from Ashgate Publications.

This review does not reflect the views of IJAAA or ERAU. This work was not peer reviewed.

High G Flight - Physiological Effects and Countermeasures