Aerodynamics and Fluid Mechanics Commons^™

Identify Aerodynamic Derivatives Of The Airplane Attitude Channel Using A Spiking Neural Network, Nguyen Quang Vinh, Nguyen Duc Thanh, Hoang Minh Dac, Truong Dang Khoa

International Journal of Aviation, Aeronautics, and Aerospace

The paper proposes a method for identifying aerodynamic coefficient derivatives of aircraft attitude channel using spiking neural network (SNN) and Gauss-Newton algorithm based on data obtained from actual flights. Using SNN combination with Gauss-Newton iterative calculation algorithm allows the identification of aerodynamic coefficient derivatives in a nonlinear model for aerodynamic parameters with higher accuracy and faster calculation time. The paper proposes an algorithm to train the SNN multi-layer network by Normalized Spiking Error Back Propagation (NSEBP), in which, in the forward propagation period, the time of output spikes is calculating by solving quadratic equations instead of detection by traditional methods. …

Performance Characteristics Design Of Pulsed Plasma Thrusters For Drag Counter-Reacting, Dr. Sam Dakka

International Journal of Aviation, Aeronautics, and Aerospace

Determining the performance characteristics of off the shelf pulsed plasma thrusters to enhance the life time of low earth orbiting platforms was investigated theoretically. Pulsed plasma thruster analysis was accomplished through development of correlations from historical data that distinguished between breech fed propellant to side fed propellant designs. Based on semi-empirical equations the power required by the thruster to counter react the drag was estimated and mapped for 1U to 27U CubeSat configurations for altitude ranging between 200km to 600km. It appears that the power required is dependent on the feeding delivery system design. For side fed designs the power …

The Detrimental Effect Of Rainfall On Performance And Stability Characteristics Of Aircrafts-A Comprehensive Review, Praneeth Hr Mr, Amit Kumar Thakur Dr

International Journal of Aviation, Aeronautics, and Aerospace

The rapidly growing global market demands faster transit of human beings and goods even in unfavorable weather conditions of rainfall. The paper gives an overview of rain research methodologies, mathematical models to track raindrops in the flow field. The paper depicts the havoc rainfall causes on performance characteristics for various phases of flight in terms of evaluation of C_L and C_D and dynamic performance parameters such as short period mode. The knowledge obtained by this review paper could help designers to modify the design of aircraft such that it has better performance, stability, and control characteristics for all …

Experimental And Computational Evaluation Of Five Hole Five Probe Flow Analyzer For Subsonic Wind Calibration, Akhila Rupesh Ms, J V Muruga Lal Jeyan Dr

International Journal of Aviation, Aeronautics, and Aerospace

It is very essential to predict the flow and its related parameters to understand real life fluid flow. The real-life fluid problems are studied with wind tunnels which gives very efficient results in practice. But in the case of wind tunnel studies flow angularities plays crucial role. Flow angularity determination includes measurement of static pressure, dynamic pressure and inflow angles. Flow prediction even hold a very strong hand in design process. Designing and testing being the foundation of any process industry, flow measurements and its related parameters have to be well evaluated. In such cases, wind tunnels play important role …

Wall-Jet Turbulence And Mixing Control By Way Of A Pulsed Inlet Velocity, Cristale D. Garnica Vallejo

Doctoral Dissertations and Master's Theses

Understanding wall-jet-induced turbulence and mixing is an important challenge in modern engineering, as drag reduction and mixing enhancement are attainable by modifying the flow development. Simulations are performed to investigate the effect on skin friction and flow mixing due to introducing controlled perturbations, at the initial shear layer of a planar wall-jet using jet inlet cyclic pulsing. The billow production by the Kelvin-Helmholtz instability, the instability that drives turbulence in a wall-jet, is modified by the excitation of the inlet velocity profile by a sine wave perturbation. Two types of wall-jet simulations are carried out, a two-dimensional compressible case at …

A Volume-Force Synthetic Disturbance Approach For High-Fidelity Of Unsteady Fluid Structure Interactions, Marina Kazarina

Doctoral Dissertations and Master's Theses

The purpose of this dissertation is to analyze the momentum source model, for generating synthetic vortical disturbance field in numerical simulations of unsteady fluid-structure interactions, access limitations of this approach, to find requirements for the computational domain, space and time resolution, and apply this model to investigate selected physical problems. For this reason a comprehensive parametric study of volume-force based method of generating spectral synthetic turbulence inside the computational domain is conducted first. The method is then extended to synthesize turbulence with arbitrary energy spectrum. The synthetic turbulence is generated through momentum source terms in Navier-Stokes equations, and the developed …

Experimental And Computational Analysis Of A 3d Printed Wing Structure, Aryslan Malik

Doctoral Dissertations and Master's Theses

Correct prediction of aeroelastic response is a crucial part in designing flutter or divergence free aircrafts within a designated flight envelope. The aeroelastic analysis includes specifically tailoring the design in order to prevent flutter (passive control) or eliminate it by applying input on control surfaces (active control). High-fidelity models such as coupled Computational Fluid Dynamics (CFD) - Computational Structural Dynamics (CSD) can obtain full structural and aerodynamic behavior of a deformable aircraft. However, these models are so large that pose a significant challenge from the control systems design perspective. Thus, the development of an aeroelastic modeling software that can be …

Preliminary Test Predictions For Scale Ram-Air Parachute Testing, Christian A. Guzman Zurita

Doctoral Dissertations and Master's Theses

The present thesis proposes a preliminary analysis to predict the aerodynamic performance for experimental tests of ram-air parachutes in a wind tunnel. A scaled experimental test setup is developed for determining the aerodynamic coefficients of lift (𝐶𝐿) and drag (𝐶𝐷) conducted in a wind tunnel. Additionally, a CFD approach where a steady-state parachute shape defined based on experiments, photographs, and literature, is presented. The accuracy of the simulation depends considerably on the ability to resolve the canopy geometry. Therefore, a CAD geometry generation is implemented for flexible control of the canopy structure by implementing design parameters, e.g., chord, span and …

Cfd Study Of Taylor-Like Vortices In Swirling Flows, Sattar Panahandehgar

Doctoral Dissertations and Master's Theses

Swirling flows are complex fluid motions that appear in various natural phenomena and man-made devices. Numerous engineering applications such as turbomachinery, jet engine combustion chambers, mixing tanks and industrial burners involve swirling flows. This wide range of applications is due to unique characteristics offered by swirling flows such as increase in mixing rate, heat transfer rate and wall shear stress. In this study the axisymmetric swirling flow behavior in the context of a hybrid rocket engine have been analyzed. While modeling the flow inside a cylindrical chamber using CFD, a similarity with the Taylor vortices instability has been observed. Similar …

Scale Interactions Within A Perturbed Plane Wall Jet, Shibani Bhatt

Doctoral Dissertations and Master's Theses

The current work focuses on exploiting this behavior to manipulate wall turbulence by targeting the large-scales of the flow. In wall turbulence the large-scales of the flow interact with the smaller scales in a non-linear manner including through a process of amplitude and frequency modulation. A plane wall jet (PWJ) is chosen as the model flow field for this work as its unique geometry allows for the controlled introduction of large-scale perturbations through acoustic forcing. The corresponding interactions because of forcing are characterized using single hot-wire measurements. The nearwall response of the PWJ over a range of large-scale forcing showed …

A Thrust Equation Treats Propellers And Rotors As Aerodynamic Cycles And Calculates Their Thrust Without Resorting To The Blade Element Method, Phillip -. Burgers

International Journal of Aviation, Aeronautics, and Aerospace

The lift generated by a translating wing of known translational speed, lift coefficient and area is calculated by a simple equation. A propeller or rotor generating thrust share the same aerodynamic principles but their different kinematics cause the calculation of their thrust to be laborious. This paper derives a thrust equation from an algebraic expansion of the Prandtl’s dynamic pressure term q_∞by adding the rotational kinetic energy of a propeller or rotor to the existing translational kinetic energy term. This thrust equation can be applied directly to propellers and rotors and assumes these to operate as cycles with …

Effect Of Chemical Reactions On The Fluidic Thrust Vectoring Of An Axisymmetric Nozzle, Rachid Chouicha, Mohamed Sellam, Said Bergheul

International Journal of Aviation, Aeronautics, and Aerospace

Abstract:

During the last years, several thrust control systems of aerospace rocket engines have been developed. The fluidic thrust vectoring is one of them; it is simple in design and offers a substantial gain in weight and in performance. Most of studies related to this device were carried out with cold gas. It’s quite legitimate to expect that the thermophysical properties of the gases may affect considerably the flow behavior. Besides, the effects of reacting gases at high temperatures, under their effects all flow parameters like to vary.

This study aims to develop a new methodology that allows studying and …

Comparison Of Flow Field In The Proximity Of A Single Planar & Wrap-Around Fin, Nayhel Sharma, Palak Saini, Hrishabh Chaudhary, Gurteg Nagi, Rakesh Kumar Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

This paper analyses the results of the computational analysis between a single planar and a wrap-around fin mounted on a semi-cylindrical body. A free-stream Computational Fluid Dynamics (CFD) model was simulated for both cases in the Mach 0.4-3.0M range at 0°Angle of attack, in which, the behavior of flow around the fin was investigated using a turbulence model of higher order discretization. The post-processing shows all the possible views of the flow dynamics around the fins, as well as the missile body. The aerodynamic drag and the rolling moment characteristics of the planar and the wrap-around fin have been …

Design And Realization Of An Unmanned Aerial Rotorcraft Vehicle Using Pressurized Inflatable Structure, Nirmal Sadasivan

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned aerial rotorcraft vehicles have many military, commercial and civil applications. There is a necessity to advance the performance on several ranges of rotorcraft for using these vehicles successfully in the expanded future roles. A lower flight time, noise disturbance and safety issues remain the key obstacles in increasing the efficiency of the rotorcraft for various applications. This work presents the design and realization of a rotorcraft using pressurized inflatable structure filled with lighter than air gas such as helium or hydrogen to provide lift assistance for the vehicle. Two iterative design procedures were developed for designing the vehicle. One …

A Comparative Aerodynamic Study Of Nonplanar Wings, Mondher Yahyaoui

International Journal of Aviation, Aeronautics, and Aerospace

In this work four nonplanar wing configurations were studied using the vortex-lattice method: the wing-winglet, the C-wing, the biplane, and the box wing. It has been shown that linear twist, which is more practical in aeronautical construction, is more than adequate to achieve the higher values of span efficiency factor obtained by a completely optimized twist distribution along the span camber, the latter being in general highly varying and thus not very practical. It has also been shown that moderate sweep can slightly increase the span efficiency factor and further reduce vortex drag. The increase is more important for the …

Computational Study Of Flow Interactions Over A Close Coupled Canard-Wing On Fighter, Setyawan Bekti Wibowo, Sutrisno Sutrisno, Tri Agung Rohmat

International Journal of Aviation, Aeronautics, and Aerospace

There have been many attempts to improve the flying performance of a fighter. By modifying the flow that occurs along the fuselage is expected to improve the performance of the aircraft. One of the indicators of combat aircraft performance is the ability to perform maneuver movement. Adding a canard as forewing on the fighter wing configuration is considered capable of raising the ability in maneuver movement. The use of canard-delta pairs will affect the performance and aerodynamic characteristics of the plane. Wings and canards with delta configuration will make the rolled-up vortex as a lifting force producer on the aircraft. …

Urban Flow And Small Unmanned Aerial System Operations In The Built Environment, Kevin A. Adkins

International Journal of Aviation, Aeronautics, and Aerospace

The Federal Aviation Administration (FAA) has put forth a set of regulations (Part 107) that govern small unmanned aerial system (sUAS) operations. These regulations restrict unmanned aircraft (UA) from flying over people and their operation to within visual line of sight (VLOS). However, as new applications for unmanned aerial systems (UAS) are discovered, their capabilities improve, and regulations evolve, there is an increasing desire to undertake urban operations, such as urban air mobility, package delivery, infrastructure inspection, and surveillance. This built environment poses new weather hazards that include enhanced wind shear and turbulence. The smaller physical dimensions, lower mass and …

Aerodynamic Design And Exploration Of A Blended Wing Body Aircraft At Subsonic Speed, Sam Dakka Dr, Oliver Johnson

International Journal of Aviation, Aeronautics, and Aerospace

Blended Wing Body (BWB) is a novel aircraft concept which provides many different aerodynamic benefits over conventional aircrafts design. This research investigated the BWB design, L/D characteristics, surface pressure distribution and span-wise lift distribution of a BWB aircraft at low to medium subsonic speeds. A BWB model was designed, manufactured and tested in a subsonic wind tunnel to validate the CFD simulation. The results gained from the investigation proved that BWB has a L/D improvement of 9.4% than conventional aircrafts and 21% increase at medium subsonic speeds (Mach 0.6) compared to lower subsonic speeds of 25 m/sec. It was found …

A New Method For The Prediction Of The Downwash Angle Gradient, Mondher Yahyaoui Dr.

International Journal of Aviation, Aeronautics, and Aerospace

A new method for the prediction of the downwash angle gradient due to aircraft wings across the span of an aft horizontal tail in the incompressible regime is presented. The approach is quite general and accounts for all practical wing geometric parameters except for wing twist where it is shown that this parameter has very little effect on the downwash angle gradient. The method consists of an empirical law which requires the prior knowledge of three constants. These have been computed either based on experimental data when available or using numerical data obtained using the vortex-lattice method. These constants are …

Uas Flight Operations In Complex Terrain: Assessing The Agricultural Impact From Hurricane Maria In The Central Mountainous Region Of Puerto Rico, Kevin Adkins

Publications

Hurricane Maria struck Puerto Rico in September 2017 as a Category 4 storm causing major damage to infrastructure, agriculture and natural ecosystems, as well as the loss of many lives. Among the crops hardest hit was coffee, one of the most important crops in Puerto Rico. As a perennial system, coffee takes various production forms along a gradient from high shade/biodiversity coffee farms to low shade coffee monocultures and therefore offers an ideal means for the study of resistance and resilience of an agroecosystem to weather and climate disturbance. During the summer of 2018, 14 impacted farms across the production …

Control Driven Scaling Effects Of Motor And Rotors For Urban Air Mobility Design, Agustin A. Giovagnoli

Doctoral Dissertations and Master's Theses

Through this thesis research the problem of controllability and propulsion associated with scaling-up consumer drones to vehicles that may carry significantly larger payloads, including passenger will be analyzed and tested. Controllability is mainly compromised due to the increasing response time of a larger rpm controlled rotor. This requires a more powerful motor, which translates into heavier and larger devices compromising the thrust-to-weight ratio. Collective pitch control at constant rpm is proposed as a first approach to mitigate the controllability problem, and it is tested in a MATLAB Simulink environment. This solution, linked to a Non-linear Dynamic Inversion controller, is simulated …

A Numerical And Experimental Evaluation Of The Turbulent Heat Flux In A Heated Jet In Crossflow, Michael R. Borghi Jr.

Doctoral Dissertations and Master's Theses

The injection of fully-developed turbulent heated air from a tube into a cooler turbulent duct flow is examined, as an analogy to film cooled turbine blades. Scale Resolving Simulations (SRS) are used to examine the flow numerically. A Detached Eddy Simulation (DES) methodology is examined but found to be ineffective at correctly capturing the physics of the flow. A Large Eddy Simulation (LES) numerical model is developed and applied in which tube and duct turbulence inflow effects are emulated using a divergence-free synthetic eddy method (SEM). The LES sensitivity to the synthetic inflow turbulence is examined with a series of …

Design Of A Heavy Lift Rc Aircraft - Society Of Automotive Engineers (Sae) Aero Design® West Competition Team, Jiyoung Hwang, Phillip Nielsen

Undergraduate Research Symposium - Prescott

The SAE Aero West design competition challenges undergraduate students to design and build an RC aircraft that will fly with the maximum number of passengers and luggage possible. The ERAU SAE team focuses on simulation-based research and project methods such as Computational Fluid Dynamics (CFD), aircraft optimization, and Finite Element Analysis (FEA). Designing and manufacturing a well-designed heavy lift aircraft and competing with other groups will give experience in solving engineering problems. The Aerodynamics team is currently focusing on score optimization, aircraft performance and configuration. The propulsion team is constructing a test rig to test various propellers and motors to …

Parametric Study Of Aerodynamic Performance Of An Airfoil With Active Circulation Control Using Leading Edge Embedded Cross-Flow Fan, M.A. Qayyum Mazumder

Doctoral Dissertations and Master's Theses

A concept of a cross-flow fan (CFF) embedded near the leading edge of an airfoil to actively control the boundary layer for lift and thrust enhancement has been proposed. The design places a cross-flow fan near the leading edge of an airfoil and flow is drawn in from the pressure side of the airfoil, energized and expelled out to the suction side near the leading edge. This CFF system simulates the active boundary layer control by blowing commercial computational fluid dynamics (CFD) code ANSYS Fluent is employed to perform 2-D calculations based on various parameters of the CFF and compared …

Experiments Of Propeller-Induced Flow Effects On A Low-Reynolds-Number Wing, Gavin K. Ananda, Robert Deters, Michael S. Selig

Publications

Novel findings are discussed in this paper that will be especially beneficial to designers and modelers of small-scale unmanned air vehicles and high-altitude long-endurance vehicles that both operate at low Reynolds numbers (Re = 50,000-300,000). Propeller-induced Oow effects in both tractor and pusher configurations on a recta ngular wing using the Wortmann FX 63-137 airfoil (a common low-Reynolds-number high-lift airfoil) are presented in this paper . Significant performance benefits can be found for a wing in the tractor configuration. Experiments, including trip tests and upper-surface oil Dow visualization, show and verify that the propeller slipstream induces early transition to turbulent …

A Computational Fluid Dynamics Study On The Aerodynamic Performance Of Ram-Air Parachutes, Angelo A. Fonseca Pazmiño

Doctoral Dissertations and Master's Theses

The modeling of a ram-air parachute presents challenges in the prediction of the inflight geometry, as there is a strong interaction between the flow field and parachute structure. This thesis presents the development of a CAD design and CFD methodology to the simulation of ram-air parachutes in steady-state conditions. Starting from a 2D rib drawing, methods were developed to approximate the 3D geometry and efficiently model the parachute as a rigid and impermeable body. The use of distortions was implemented on a 2D, pseudo-2D, and 3D model to enhance their behavior during a real flight. The SST turbulence model was …

A Computational Analysis Of The Aerodynamics And Aeroacoustics Of Jets With Fluid Injection, Marco Coderoni

Doctoral Dissertations and Master's Theses

A detailed numerical analysis of fluidic injection as a tool to reduce noise emission is presented here. The noise reduction strategy, developed at the Pennsylvania State University, is based on injectors that blow air into the diverging section of the nozzle to emulate the effect of interior corrugation on the jet plume. The advantage is that the injection can be activated during takeoff and turned o_ during other phases of flight so that performance is not affected. Numerical simulations are performed on a military-style nozzle based on the GE F400-series engines, with a design Mach number of 1:65, for over-expanded …

Experimental Investigation Of A New Spiral Wingtip, Naseeb Ahmed Siddiqui, Mohammed Aldheeb, Waqar Asrar, Erwin Sulaeman

International Journal of Aviation, Aeronautics, and Aerospace

Experiments on the relative merits and demerits of slotted wingtips mimicking a bird’s primary feathers have been performed. The real emargination length of feather tips, their flexibility and curved shapes during cruise are considered in the present study. The experiments were performed at a Reynolds number of 3.7 x 10⁵ on a symmetric flat plate half wing of aspect ratio 3. Lift, drag and pitching moments were measured using a six component aerodynamic balance. Four different shapes inspired by bird primary feathers have been analysed. The rigid curved tip performed the best increasing the L/D ratio by 20%. This …

Nonlinear Control Of Underactuated And Constrained Systems, Derek Hoffman

Doctoral Dissertations and Master's Theses

It is the purpose of this document to elaborate on the control of systems that are underactuated or otherwise constrained. To do so, local- and global-coordinate formulations are implemented to generate well-defined system dynamics for a multitude of scenarios. These dynamics are shown to lie on manifolds defined by mathematical restrictions, allowing for singularity-free modeling for global considerations. Feed-back controllers by extension share these benefits, facilitating singularity-free control algorithms as a result. Further, unactuated degrees of freedom can be treated as additional constraints, resulting in an embedded manifold upon the original dynamics. A transformation between a provided set of dynamical …

Aerodynamic Analysis Of Low Speed Wing Design Using Taguchi L9 Orthogonal Array, Kenneth Witcher, Ian Mcandrew, Elena Vishnevskaya

Publications

The study of aerodynamics has been preoccupied with understanding flight at increasing speeds and ultimately supersonic. Today, this pursuit has advanced the science for both Hypersonic and Transonic flight to near Mach 1 supporting economical commercial flight operations. This research presents the data from a Taguchi array on low speed with twin wing designs to establish the design parameters for their use in low speed and high altitude. Also presented is how aerodynamic advantages can be achieved through understanding the interactions of parameters and their use. This is compared to operational effectiveness when applied to remotely piloted aircraft that are …