Aerodynamics and Fluid Mechanics Commons^™

Similarity Analysis Of A Swirling Counter-Flow, Jitesh Rane

Doctoral Dissertations and Master's Theses

Swirling counter-flows are used in numerous engineering applications, like combustion, heat exchangers, cyclonic separation and mixing, etc. These swirling counter-flows produce complex flow fields. It is important to study these types of flows in order to use them properly in many applications.

The present work provides insight into the flowfield inside a swirling counter-flow when the fluid is injected tangentially in a cylindrical container. A semi-analytical solution is developed by starting with the full Navier-Stokes equation and using a similarity analysis. A decaying swirl along the axis of the cylinder is assumed, which reduces the Navier-Stokes equations to first order …

Surface Structure And Its Effect On Reducing Drag, Ragini Ramachandran

Doctoral Dissertations and Master's Theses

A miniature subsonic open return wind tunnel was designed and fabricated to measure drag on small test models at low Reynolds numbers. The wind tunnel featured a sensitive strain gauge type load cell. The average drag coefficient of sphere and cube test models were used to validate the miniature wind tunnel, and the values obtained were consistent with published results over the range of Reynolds numbers tested. These initial results gave confidence that the tunnel could be used to study the effects of surface finish on the drag of various models. Several fabrics with differing ribbed surface structures, including a …

Determination Of A Simplified High-Order Vortex Equation For Radial Equilibrium With Cfd Verification, Travis K. Matsumoto

Doctoral Dissertations and Master's Theses

The goal of this thesis is to determine a flow model that provides a better blade design over current design techniques utilizing a hybrid vortex model. This hybrid vortex model combines the well-established simple radial equilibrium vortex models into a higher order equation that will establish the basis for a more flow-accurate model. In this paper, we will discuss the basis and derivation of these vortex models, the shortcomings of current techniques, and verification of the new vortex model with empirical data via Computational Fluid Dynamic (CFD). The simple radial equilibrium equation set has been known to the scientific community …

Efficient General Computational Method For Estimation Of Standard Atmosphere Parameters, Nihad E. Daidzic Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

Knowledge of standard air temperature, pressure, density, speed of sound, and viscosity as a function of altitude is essential information in aircraft design, performance testing, pressure altimeter calibration, and several other aeronautical engineering and aviation science applications. A new efficient computational method for rapid calculations of standard atmospheric parameters up to 86 orthometric km is presented. Additionally, mass and weight of each standard atmospheric layer were calculated using a numerical integration method. The sum of all fractional masses and weights represents the total mass and weight of Earth’s atmosphere. The results obtained here agree well with measurements and models of …

Design And Dynamic Analysis Of A Variable-Sweep, Variable-Span Morphing Uav, Nirmit Prabhakar

Doctoral Dissertations and Master's Theses

Morphing wings have the potential to optimize UAV performance for a variety of flight conditions and maneuvers. The ability to vary both the wing sweep and span can enable maximum performance for a diverse range of flight regimes. For example, low-speed missions can be optimized using a wing with high aspect ratio and no wing sweep whereas high-speed missions are optimized with low aspect ratio wings and large wing sweep. Different static morphing wing configurations clearly result in varying aerodynamics and, as a result, varying dynamic modes. Another important consideration, however, is the transient dynamics that occur when transitioning between …

Achieving Global Range In Future Subsonic And Supersonic Airplanes, Nihad E. Daidzic Ph.D., Sc.D.

International Journal of Aviation, Aeronautics, and Aerospace

No commercial airplane in service today is able to fly half great-circle distances over the globe and achieve the non-stop or the global range to any antipodal location on Earth. A subsonic jetliner has the optimum cruising speed at Mach numbers approaching the drag divergence Mach number while still preserving relatively high aerodynamic efficiency. Various fuel-flow laws were used to investigate the cruise performance of subsonic and supersonic aircraft. The effect of wind and aircraft weight and how it affects the optimal cruising airspeed was investigated. Of all different operational cruising techniques, the cruise-climb at high Mach numbers is the …

Aerodynamic Optimization Of Box Wing – A Case Study, Adeel Khalid, Parth Kumar

International Journal of Aviation, Aeronautics, and Aerospace

The optimization of a possible medium range box wing commercial airliner is presented in three stages. Preliminary research is used to determine various parameters for a potential box wing model, and a baseline model is designed in Autodesk Inventor, based upon the cantilever Airbus A330-200, an aircraft of a similar role. The Computational Fluid Dynamics (CFD) software used in this project is Dassault Systèmes SolidWorks, which is validated through comparing the NACA 0009 airfoil lift and drag polars with published results. The first stage of optimization is performed on the airfoil shape, with 8 different designs being tested against the …

A Cfd Investigation Of The Hydrodynamic Characteristics Of Fluid Flow Through An Impeller And Multi-Objective Design Optimization Of A Centrifugal Pump, Mohammed Khammat Sagban

Doctoral Dissertations and Master's Theses

In this thesis, the first part is conducting an investigation of the hydrodynamic characteristics (pressure and velocity) of fluid flow (water) through an impeller of a centrifugal pump. To illustrate a one-dimensional model is used to identify an impeller of a GDM 10 x 12 HD centrifugal pump using Vista CPD design and BladeGen tool. A three-dimensional model is then built with a commercial software package ANSYS Blade Modeler. The structured mesh of the impeller blade is obtained by using TurboGrid system. The volute of the centrifugal pump is built in ANSYS geometry, and an unstructured mesh is accomplished by …

Exploration Of A Computational Fluid Dynamics Integrated Design Methodology For Potential Application To A Wind Turbine Blade, Gaurav Kapoor

Doctoral Dissertations and Master's Theses

The main purpose of this thesis is to conduct a parametric sensitivity study on the blade design of AOC 15/50 wind turbine based on a CFD approach and optimize the blade design for maximizing the power output. The ANSYS® Fluent® flow solver using the k-ω SST turbulence model was validated by simulating the flow over two dimensional airfoils comprising the AOC 15/50 wind turbine blade. The CFD results have shown a considerable agreement with the experimental data for the airfoils. Parametric correlation study and sensitivity analysis were conducted by performing actual flow simulations over the turbine blade using ANSYS® Fluent®. …

Characterization And Low-Dimensional Modeling Of Urban Fluid Flow, Dietmar Rempfer, Candace Wark, Bruno Monnier, Sriharsha Kandala

Publications

This report describes work that was done under AFOSR Contract Number FA9550-11-1-0056, studying the structure of a model urban boundary layer flow. The model geometry consisted of a set of plexiglass blocks, and the flow around this geometry was studied both experimentally as well as computationally. For the experiment, a Stereoscopic Particle Image Velocimetry (SPIV) method was developed that allows for a three-dimensional description of this urban flow, and helps gain insight into the characteristic flow structures in the streets and canyons of our model urban geometry. On the computational side, a new spectral-element code was developed that was demonstrated …

Unsteady Viscous Cavity Flow Using Computational Fluid Dynamics, Chandramouli Vadlamudi

Doctoral Dissertations and Master's Theses

The problem of unsteady viscous incompressible flow in a two-dimensional cavity is treated using the unsteady incompressible Navier-Stokes equations with various initial and boundary conditions. First the case of a square cavity with one inlet and one outlet is treated in steady and unsteady flows. The software package ANSYS FLUENT was used in the CFD simulations. This approach captures the appearance of separation bubbles and vortex formation inside the cavity. Steady state flows are also obtained from the unsteady simulations after convergence of the time dependent solutions. Then the case of a cavity with a synthetic jet and two outlets …

Separation Bubbles And Vortex Formation In Cavity Flows, Kartheek Ravulapati

Doctoral Dissertations and Master's Theses

This research is a computational fluid dynamic study of the formation of vortices and separation bubbles in a square cavity as well as in a cylindrical cavity. Whereas there has been previous research work on the problem of a free stream over different types of cavities, like open and closed cavities or lid driven cavities, this research on an inlet induced flow inside a square cavity lead to unusual and interesting basic fluid dynamical phenomena. The flow in a square cavity and in a cylindrical cavity is simulated over a range of Reynolds numbers and the appearance of separation bubbles …

Performance Improvement Through Velocity Triangle Optimization-Driven Redesign For Mitigating The Horseshoe Vortex In Axial Turbines, Vladislav Shulman

Doctoral Dissertations and Master's Theses

Momentum differences between the neighboring streamlines at the end wall/primary flow interaction region of an axial turbine stage induce three-dimensional vortical flow structures, such as the leading edge horseshoe vortex, resulting in significant aerodynamic performance deterioration. Reducing the effect of such flow instabilities requires turbine blade modification to discourage boundary layer roll-up, but traditional structural modification design systems can be prohibitively complex and time-intensive.

To address this problem, this study contributes a blade modification method involving airfoil shape optimization, designed to adjust the leading edge airfoil shape in horseshoe vortex-affected turbine applications. The key insight is that airfoil design (treated …

3d Aerodynamic Optimization Of Nrel Vi Wind Turbine Blade For Increased Power Output And Visualization Of Flow Characteristics, Tsewang Rabga Shrestha

Doctoral Dissertations and Master's Theses

The thesis focuses on the aspect of optimization of NREL VI wind turbine blade for increased power output using commercial solver ANSYS 14.5. The power curve obtained from BEMT, Baseline NREL VI CFD Simulations and Optimized Blade Simulations are compared with experimental results. Over prediction is observed in the theoretical result while computational analysis under predicts power produced at post stall region. Parameter correlation and sensitivity analysis study relates the effectiveness of design parameters on the objective outcome. Scatter plots and Determination Matrix indicate the problem setup as non-linear quadratic. Adaptive Single Objective Optimization algorithm is used for the optimization …

Flow Separation Control Using Synthetic Jets On A Flat Plate, Karunakaran Saambavi

Doctoral Dissertations and Master's Theses

The primary goal of this thesis is to assess the effect of synthetic jets on flow separation. CFD simulation is conducted for laminar flow over a flat plate using the commercial software ANSYS FLUENT. The oscillating zero mass jet flow is simulated by imposing a harmonically varying boundary condition on the wall surface.

In this work, the effect of synthetic jets for different angles of attack and different frequencies ranging from 200 Hz to 800 Hz was assessed. The application of the synthetic jet actuators is based in their ability to energize the boundary layer, thereby providing significant increase in …

Slosh Damping With Floating Magnetoactive Micro-Baffles, Vijay Santhanam

Doctoral Dissertations and Master's Theses

Liquid sloshing within propellant tanks of launch vehicles and other major vehicles has been a major concern. Various methods have been utilized for the damping of slosh through Propellant Management Devices (PMD) accomplishing a wide range of results. Exploratory research conducted at the Embry-Riddle Aeronautical University Fuel Slosh Test Facility in development of an innovative PMD is presented. Embedding floating micro-baffles with a magnetoactive material such that the baffle can be manipulated when exposed to a magnetic field preserves the benefits of both floating and static baffle designs. Activated micro-baffles form a rigid layer at the free surface and provide …

Investigation Of Grid Adaptation To Reduce Computational Efforts For A 2-D Hydrogen-Fueled Dual-Mode Scramjet, Kam Keong Foo

Doctoral Dissertations and Master's Theses

A two-dimensional dual-mode scramjet flowpath is developed and evaluated using the ANSYS Fluent density-based flow solver with various computational grids. Results are obtained for fuel-off, fuel-on non-reacting, and fuel-on reacting cases at different equivalence ratios. A one-step global chemical kinetics hydrogen-air model is used in conjunction with the eddy-dissipation model. Coarse, medium and fine computational grids are used to evaluate grid sensitivity and to investigate a lack of grid independence. Different grid adaptation strategies are performed on the coarse grid in an attempt to emulate the solutions obtained from the finer grids. The goal of this study is to investigate …

Fluid-Structure Interaction And Multidisciplinary Design Analysis Optimization Of Composite Wind Turbine Blade, Naishadh G. Vasjaliya

Doctoral Dissertations and Master's Theses

A multidisciplinary design analysis optimization (MDAO) process is defined for a composite wind turbine blade to optimize its aerodynamic and structural performance by developing a fluid-structural interaction (FSI) system. The objectives are to maximize aerodynamic efficiency and structural robustness while reducing blade mass and total cost. In the previous research, a MDO process of a composite wind turbine blade has been pioneered as an effective process to develop structurally optimized blade design. Present MDAO process is defined in conjunction with structural and aerodynamic performance of the blade which is divided into three steps and the design variables considered are related …

Design Considerations And Requirements For In-Flight Refueling Of Unmanned Vehicles, Ian R. Mcandrew, Kenneth Witcher

Publications

The need to refuel in-flight has become a significant part of military strategy for air forces to work at further distances from safe shores. The use of Unmanned Vehicles is increasing and expected to be the principal part of military deployment. This paper will address the concepts and requirements for applying refueling unmanned vehicles in a military context for supporting fixed and rotor aircraft. Design aspects of human factors in the process are considered, reviewed and solutions proposed to allow for the first generation of designs to be developed. Furthermore, the practical and operational limitations will be addressed as part …

Investigation Of Pulse Detonation Engines; Theory, Design And Analysis, Jeff Vizcaino

Doctoral Dissertations and Master's Theses

Detonation and constant volume combustion has been known to the scientific community for some time but only recently has active research been done into its applications. Detonation based engines have received much attention in the last two decades because of its simple design and potential benefits to the aerospace industry. It is then the goal of this study to provide a background into detonation theory and application and establish the basis for future detonation based research at Embry-Riddle Aeronautical University. In this paper we will discuss the experimental aspects of building, testing, and analysis of a pulsed detonation tube …

Novel Airframe Design For The Dual-Aircraft Atmospheric Platform Flight Concept, Eric Michael Mckee

Doctoral Dissertations and Master's Theses

A high-altitude, long-endurance unmanned aerial airframe was designed for the innovative Dual-Aircraft Atmospheric Platform flight concept that exploits stratospheric wind velocity gradients to remain aloft indefinitely. Classical aircraft preliminary design techniques and high-fidelity tools were used to establish a baseline configuration.

Performance characteristics of numerous airfoil profiles were evaluated with two-dimensional flow software in an effort to determine the best-candidate airfoil for the unique application. Vortex-Lattice method tools were used to investigate the sensitivity of three-dimensional design parameters upon overall vehicle aerodynamic performance and determine both static and dynamic stability characteristics of the airframe. Performance capabilities of the finalized airframe …

High-Fidelity Modeling Of Airfoil Interaction With Upstream Turbulence, Jacob Brodnick

Doctoral Dissertations and Master's Theses

To supplement past research on low speed unsteady airfoil responses to upstream disturbances, this work proposes and investigates a method to generate a turbulent momentum source to be convected downstream and interact with an SD7003 airfoil in a high-fidelity numerical simulation. A perturbation velocity field is generated from a summation of Fourier harmonics and applied to the forcing function in the momentum terms of the Navier Stokes Equations. The result is a three-dimensional, divergence-free, convected turbulent gust with applied statistical parameters. A parametric study has been done in 2D and 3D comparing the resultant flow fields and airfoil interactions for …

Development Of A Higher-Order Navier-Stokes Solver For Transient Compressible Flows, Arjun Vijayanarayanan

Doctoral Dissertations and Master's Theses

A higher‐order density based Navier‐Stokes solver was developed for 2‐Dimensional flows using the finite volume approach. The Van leer flux‐splitting technique was used to calculate the fluxes. The second‐order spatial accuracy was achieved using the variable extrapolation method developed by Van leer called the Montone Upstream Centered Scheme for Conservation Laws (MUSCL) approach. The code development was done using Matlab. The code was verified using two validation cases. Firstly, subsonic, transonic, and supersonic flows over the 2‐D bump were simulated, and the results of the code were compared to the results from Fluent. Secondly, the shock‐tube problem was chosen, and …

Numerical Analysis Of Gun Barrel Pressure Blast Using Dynamic Mesh Adaption, Sathish Xavier

Doctoral Dissertations and Master's Theses

A Computational Fluid Dynamics (CFD) method has been applied to simulate the pressure blast of the projectile which is launched from a barrel and to investigate the pressure distribution and sound pressure level (dB) along different positions away from the gun axis and towards the fuselage of the aircraft. Fluent was employed to simulate the unsteady flow using dynamic mesh with moving boundary. Most CFD based ballistics-model requires additional thermodynamic functions which must be derived from the Noble-Abel equation of state. The unsteady, axisymmetric Navier Stokes equation systems were numerically solved using the Advection Upstream Splitting Method (AUSM) scheme; with …

Effect Of Thermally Induced Deformation In A Supersonic Combustion Facility, Aditya Ajit Gupte

Master's Theses - Daytona Beach

Nastran and ANSYS finite element analysis (FEA) and Wind-US computational fluid dynamics (CFD) solvers are used to simulate the effect of thermal deformation on the reacting flow developing within the University of Virginia (UVa) Supersonic Combustion Facility (SCF). A detailed thermal-structural model is developed to resolve the temperature distribution and the resulting structural deformation taking place within the scramjet engine flowpath. The predicted thermal deformation is used to refine the CFD model and produce a new set of results for direct comparison with experiment during both ramjet and scramjet modes of operation. Improved agreement between CFD and experiment is afforded …

Analytic Treatment Of Vortex States In Cylindrical Superconductors In Applied Axial Magnetic Field, Andrei Ludu, J. Van Deun, M. V, Milosevic, A. Cuyt, F. M. Peeters

Publications

We solve the linear Ginzburg–Landau GL equation in the presence of a uniform magnetic field with cylindrical symmetry and we find analytic expressions for the eigenfunctions in terms of the confluent hypergeometric functions. The discrete spectrum results from an implicit equation associated to the boundary conditions and it is resolved in analytic form using the continued fractions formalism. We study the dependence of the spectrum and the eigenfunctions on the sample size and the surface conditions for solid and hollow cylindrical superconductors. Finally, the solutions of the nonlinear GL formalism are constructed as expansions in the linear GL eigenfunction basis …

Extension To Multiple Species Of A Two-Equation Turbulence Model For High Speed Flows, Martin Horvath

Master's Theses - Daytona Beach

The Wilcox (2006) k-co turbulence model has been extended to multiple species and implemented in a CFD code for high speed flows using the Steger-Warming flux-vector splitting scheme. The model was chosen because compressibility corrections are not required, nor are viscous damping factors or wall functions to produce the law of the wall, and it has previously been validated for approximately one hundred test cases ranging from incompressible to hypersonic flow regimes. Initial validation cases using first-order accuracy have been performed, including a Mach 2.5 flow past a backward-facing step and a Mach 2.85 flow into a 24° compression corner. …

Numerical Simulation Of A Liquid Jet Atomization And Break-Up Using Ansys-Cfx 12.0, Yash Akhil Bhatt

Master's Theses - Daytona Beach

Break-up and atomization characteristics of JetA liquid fuel were investigated numerically. The results have been compared to various experimental results to evaluate the accuracy of the numerical model. The CFD code ANSYS-CFX 12.0 was used to carry out the steady state analysis at different time scales. A comparison between the atomization characteristics of a pressure jet atomizer and an air-blast atomizer is shown. By employing a Lagrangian particle tracking method to track the path of the liquid particles, the liquid jet/spray phenomena was studied in light of low and high back pressure environments. The 'BLOB' primary atomization model and the …

Stability Of Fully Nonlinear Stokes Waves On Deep Water: Part 1. Perturbation Theory, Shahrdad Sajjadi, David L. Ross

Publications

We consider a full set of harmonics for the Stokes wave in deep water in the absence of viscosity, and examine the role that higher harmonics play in modifying the classical Benjamin-Feir instability. Using a representation of the wave coefficients due to Wilton, a perturbation analysis shows that the Stokes wave may become unbounded due to interactions between the N^th harmonic of the primary wave train and a set of harmonics of a disturbance. If the frequency of the n^th harmonic is denoted Ꙍ_n = Ꙍ(1 ± ꭉ) then instability will occur if

√2 k n^{n …}

Parametric Viscous Analysis Of Gust Interaction With Stationary And Elastically Mounted Airfoil, Timothy M. Hollenshade Jr.

Master's Theses - Daytona Beach

This thesis details the development and implementation of a module within a high-accuracy numerical viscous analysis code to simulate the nonlinear interaction of SD7003 airfoil with non-uniform, unsteady incoming flow. The study is focused on the low-Re number unsteady flows typical of MAV applications in which a gust encounter can induce a particularly significant aerodynamic and aeroelastic response. Efficient source models are developed to introduce sharp-edge and time-harmonic gust perturbations with specified amplitude, frequency and duration inside the computational domain through the source terms in the governing momentum equations. Parametric analysis of gust-airfoil interactions for different steady airfoil loads is …