Aerospace Engineering Commons^™

Design, Construction And Testing Of A 3-Component Force Balance For Educational Wind Tunnels In Undergraduate Aerodynamics, Milan Tomin, Marco Scipioni, Benjamin Gatti

Journal of Aviation/Aerospace Education & Research

This article is focused on providing detailed instructions on how to build and use a force balance for educational wind tunnels. The article’s objective is to encourage undergraduate students in underfunded programs to engage in the field of aerodynamics. The discussed force balance represents an affordable device that only requires basic components like Arduino board, a servo motor, and acrylic and aluminum as construction materials. A simple data collection example is included at the end of the article showing that this simple force balance can collect meaningful data about lift, drag, and moment coefficient of a tested airfoil.

A Study Of The Aeroacoustics Of Swept Propellers For Small Unmanned Aerial Vehicles, Arthur David Wiedemann

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, small unmanned aerial vehicles (UAVs) have increased in availability and use in both public and commercial sectors. This increased use of small UAVs or “drones” has the unfortunate consequence of introducing excessive noise into communities where they operate. Implementation of noise reduction methods is necessary if we wish to see expanded use of drones in public areas. With electric propulsion, the primary source of noise is the rotor/propeller used in contemporary multi-rotor configurations. In this thesis, the aerodynamics and acoustic behavior of various swept propellers is examined with computational and experimental methods.

A family of propeller geometries …

Avia 201 Project 1 Windtunnel Lab Form Ver 1.20 20200323, Nihad E. Daidzic

Aviation Department Publications

To introduce aviation/aeronautics/aerospace students to wind tunnel(s) and methods used in experimental identification of various aerodynamic (and stability) coefficients of airfoils (2D), wings (3D) and scale models.

A Cfd Study Investigating Drag Reduction For Different Offset And Inline Distance For Two Trucks Platooning, Wael Mokhtar, Kyle Dinger, Shardul Kachare, Mdrazib Hossain, Colin Britcher

Mechanical & Aerospace Engineering Faculty Publications

The automotive industry invests huge resources to improve fuel consumption of commercial vehicles by improving their aerodynamic efficiency. Recently, numerous studies investigating the effect of platooning on aerodynamic drag of semi-trucks have been performed by researchers indicating a positive impact. For the present study, a three-dimensional computational study was performed to investigate the effect of varying offset and linear distance during platooning on the total drag of two semi-trucks. The study was conducted on a full-scale model using Reynold’s Averaged Navier-Strokes governing equations for a moving ground simulation using the STAR-CCM+ computational package. Furthermore, for turbulence, the standard k- …

Unsteady Aerodynamic Analysis Of Wind Harvesting Aircraft, Judd Mehr, Eduardo Alvarez, Andrew Ning

Faculty Publications

Airborne Wind Energy (AWE) technology aspires to provide increased options for wind energy harvesting. This includes increased feasibility for temporary and remote installations, as well as the ability to operate at wind speeds both lower and higher than traditional turbines. Additionally, the hope is to be able to produce these extensions of wind energy technology at a lower cost than conventional technologies. As AWE technology is still in its infancy, however, there is very little published information concerning the aerodynamic details of the technology. We have created a set of aerodynamic analysis tools which we apply to wind harvesting aircraft, …

Experimental And Computational Evaluation Of Five Hole Five Probe Flow Analyzer For Subsonic Wind Calibration, Akhila Rupesh Ms, J V Muruga Lal Jeyan Dr

International Journal of Aviation, Aeronautics, and Aerospace

It is very essential to predict the flow and its related parameters to understand real life fluid flow. The real-life fluid problems are studied with wind tunnels which gives very efficient results in practice. But in the case of wind tunnel studies flow angularities plays crucial role. Flow angularity determination includes measurement of static pressure, dynamic pressure and inflow angles. Flow prediction even hold a very strong hand in design process. Designing and testing being the foundation of any process industry, flow measurements and its related parameters have to be well evaluated. In such cases, wind tunnels play important role …

Wind Tunnel Measurements And Data Analysis Tutorial, Nihad E. Daidzic

Aviation Department Publications

This tutorial gives details on processing of raw aerodynamic data measured directly in the wind tunnel on airfoils and wings. Also procedures and equations from the lab report are given and demonstrated how to compute geometric characteristics of wings/airfoils and air data. All numeric results are typically rounded to five significant digits.

Initial Stage Of Fluid-Structure Interaction Of A Celestial Icosahedron Shaped Vacuum Lighter Than Air Vehicle, Dustin P. Graves

Theses and Dissertations

The analysis of a celestial icosahedron geometry is considered as a potential design for a Vacuum Lighter than Air Vehicle (VLTAV). The goal of the analysis is ultimately to understand the initial fluid-structure interaction of the VLTAV and the surrounding airflow. Up to this point, previous research analyzed the celestial icosahedron VLTAV in relation to withstanding a symmetric sea-level pressure applied to the membrane of the structure. This scenario simulates an internal vacuum being applied in the worst-case atmospheric environmental condition. The next step in analysis is to determine the aerodynamic effects of the geometry. The experimental setup for obtaining …

Sweep And Taper Analysis Of Surfboard Fins Using Computational Fluid Dynamics, Brandon James Baldovin

Master's Theses

The research presented here provides a basis for understanding the hydrodynamics of surfboard fin geometries. While there have been select studies on fins there has been little correlation to the shape of the fin and its corresponding hydrodynamic performance. This research analyzes how changing the planform shape of a surfboard fin effects its performance and flow field. This was done by isolating the taper and sweep distribution of a baseline geometry and varying each parameter individually whilst maintaining a constant span and surface area. The baseline surfboard fin was used as a template in Matlab to generate a set of …

A Higher-Order Method Implemented In An Unstructured Panel Code To Model Linearized Supersonic Flows, Jake Daniel Davis

Master's Theses

Since their conception in the 1960s, panel codes have remained a critical tool in the design and development of air vehicles. With continued advancement in computational technologies, today's codes are able to solve flow fields around arbitrary bodies more quickly and with higher fidelity than those that preceded them. Panel codes prove most useful during the conceptual design phase of an air vehicle, allowing engineers to iterate designs, and generate full solutions of the flow field around a vehicle in a matter of seconds to minutes instead of hours to days using traditional CFD methods. There have been relatively few …

Wake Vortex Pair Formation As An Analog For Dust Devil And Tornado Genesis, Robert L. Ash

Mechanical & Aerospace Engineering Faculty Publications

In 1966, meteorologist R.S. Scorer attempted to explain how large-scale oceanic tropical depressions become hurricanes or typhoons. His model was based on the idea that when these large-scale tropical depression structures begin to rotate, mostly due to Coriolis effects, an annular outer portion of that structure changes suddenly to a potential vortex segment, with the same outer radial limit as the low-pressure structure, but with an inner radius that conserves the overall system angular momentum and kinetic energy. By analogy with the "jump" instability describing sudden buckling of a vertical column, this paper shows that his conjecture merits additional consideration. …

Comparison Of Flow Field In The Proximity Of A Single Planar & Wrap-Around Fin, Nayhel Sharma, Palak Saini, Hrishabh Chaudhary, Gurteg Nagi, Rakesh Kumar Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

This paper analyses the results of the computational analysis between a single planar and a wrap-around fin mounted on a semi-cylindrical body. A free-stream Computational Fluid Dynamics (CFD) model was simulated for both cases in the Mach 0.4-3.0M range at 0°Angle of attack, in which, the behavior of flow around the fin was investigated using a turbulence model of higher order discretization. The post-processing shows all the possible views of the flow dynamics around the fins, as well as the missile body. The aerodynamic drag and the rolling moment characteristics of the planar and the wrap-around fin have been …

Blended Wing Design Considerations For A Next Generation Commercial Aircraft, Jay Abhilash Vora

Browse all Theses and Dissertations

The current aircraft design has not changed significantly in the last few decades. Growing environmental concerns and fuel prices are driving manufacturers to develop unconventional but efficient aircraft configurations. The blended wing body (BWB) configuration provides an alternate and more efficient means of subsonic travel. The BWB aircraft replaces the traditional wings and fuselage with hybrid wing shape where the fuselage and wings have integrated. Major aircraft manufacturers are researching the BWB concept incorporating electric propulsion for civil transport use. In this research a 300 passenger BWB aircraft aerodynamic shape is designed. This aircraft is used to assess the aerodynamic …

Investigating The Effect Of An Upstream Spheroid On Tandem Hydrofoils, Joel Tynan Guerra

Master's Theses

This thesis documents a series of three dimensional unsteady Reynolds Averaged Navier-Stokes CFD simulations used to investigate the influence of an upstream prolate spheroid body on tandem pitching hydrofoils. The model is validated by performing separate CFD simulations on the body and pitching hydrofoils and comparing results to existing experimental data. The simulations were run for a range of Strouhal numbers (0.2-0.5) and phase differences (0-π). Results were compared to identical simulations without an upstream body to determine how the body affects thrust generation and the unsteady flow field.

The combined time-averaged thrust increases with Strouhal number, and is highest …

Bi-Stability In The Wakes Of Platooning Ahmed Bodies, Daniel M. Stalters

Master's Theses

Autonomous heavy vehicles will enable the promise of decreased energy consumption through the ability to platoon in closer formation than is currently safe or legal. It is therefore increasingly important to understand the complex and dynamic wake interactions between vehicles operating in close proximity for aerodynamic gains. In recent years, a growing body of research has documented a bi-stable, shifting wake generated behind the Ahmed reference bluff body. At the same time, studies of platooning Ahmed bodies have focused on changes to the body forces and moments at different following distances or lateral offsets, typically based around time-averaged measurements or …

Parametric Study Of Aerodynamic Performance Of An Airfoil With Active Circulation Control Using Leading Edge Embedded Cross-Flow Fan, M.A. Qayyum Mazumder

Doctoral Dissertations and Master's Theses

A concept of a cross-flow fan (CFF) embedded near the leading edge of an airfoil to actively control the boundary layer for lift and thrust enhancement has been proposed. The design places a cross-flow fan near the leading edge of an airfoil and flow is drawn in from the pressure side of the airfoil, energized and expelled out to the suction side near the leading edge. This CFF system simulates the active boundary layer control by blowing commercial computational fluid dynamics (CFD) code ANSYS Fluent is employed to perform 2-D calculations based on various parameters of the CFF and compared …

Design And Performance Estimation Of A Low-Reynolds Number Unmanned Aircraft System, Sean Lauderdale King

LSU Master's Theses

The purpose of this thesis is to conceptually design a fixed-wing unmanned aircraft systems (UAS) with a higher flight-time and top stable speed than comparable systems. The vehicle adheres to specifications derived from the client, the market, and the Federal Aviation Administration (FAA). To broadly meet these requirements, the vehicle must fly for a minimum of three hours, return to the original flight path quickly if perturbed, and must be hand-launched. The vehicle designed must also have a large potential center of gravity movement to allow for customization of the planform and client customization.

An iterative design process was used …

A Computational Fluid Dynamics Study On The Aerodynamic Performance Of Ram-Air Parachutes, Angelo A. Fonseca Pazmiño

Doctoral Dissertations and Master's Theses

The modeling of a ram-air parachute presents challenges in the prediction of the inflight geometry, as there is a strong interaction between the flow field and parachute structure. This thesis presents the development of a CAD design and CFD methodology to the simulation of ram-air parachutes in steady-state conditions. Starting from a 2D rib drawing, methods were developed to approximate the 3D geometry and efficiently model the parachute as a rigid and impermeable body. The use of distortions was implemented on a 2D, pseudo-2D, and 3D model to enhance their behavior during a real flight. The SST turbulence model was …

Validation Of Cfd Simulations For Hypersonic Flow Over A Yawed Cone, Julian Cecil

McKelvey School of Engineering Graduate Student Theses & Dissertations

This study aims to numerically simulate the wind tunnel results for hypersonic flow over a circular cone of semi-apex angle of 10 degrees yawed from 0° to 20° using the commercial computational fluid dynamics software ANSYS Fluent. The ANSYS workbench is used to create the 10° semi-apex circular cone with a shock aligned structured mesh of 3.05 million cells surrounding the cone. Simulation boundary conditions for pressure and temperature in the far field correspond to Tracy’s wind tunnel experiment at Cal Tech. The six simulations cases are conducted for yaw angles of 0, 8, 12, 16, 20 and 24 degrees. …

Aerodynamic Design And Analysis Of A Large-Scale Stall-Regulated H-Type Vertical Axis Wind Turbine For An Offshire Floating Installation, Brian Peter Hand

PhDs

Wind energy has witnessed a consistent expansion over the past decade, especially with the move to offshore installation. There is an increasing need to further exploit superior offshore wind resources, which is pushing multi-megawatt wind turbines into deeper water locations where the current popular horizontal axis wind turbine configuration is not entirely suitable. In particular, there has been a renewed interest in the vertical axis wind turbine (VAWT) configuration due to its inherent design attributes for an offshore floating application and also its potential to provide a significant reduction in the system cost of energy. However, challenges still remain as …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

LSU New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Aerodynamic And Performance Analysis Of A Morphing Helicopter Rotor System, Vinay Gopal Krishnan

Doctoral Dissertations and Master's Theses

The purpose of this study was to investigate the effect of rotor morphing, specifically variable rotor speed and variable blade twist, on various parameters such as the distribution of angle of attack, lift, power, thrust and/or other metrics describing the performance of a helicopter rotor. A MATLAB based blade element theory model was developed and executed for different flight conditions. The model was validated against the flight test data of a UH-60. Effects on power, lift to drag ratio and rotor drag from variations in blade twist, rotor speed, rotor radius and blade chord was analyzed. Morphing cases were applied …

Wing Deflection Analysis Of 3d Printed Wind Tunnel Models, Matthew G. Paul

Master's Theses

This work investigates the feasibility of producing small scale, low aerodynamic loading wind tunnel models, using FDM 3D printing methods, that are both structurally and aerodynamically representative in the wind tunnel. To verify the applicability of this approach, a 2.07% scale model of the NASA CRM was produced, whose wings were manufacturing using a Finite Deposition Modeling 3D printer. Experimental data was compared to numerical simulations to determine percent difference in wake distribution and wingtip deflection for multiple configurations.

Numerical simulation data taken in the form of CFD and FEA was used to validate data taken in the wind tunnel …

Design And Computational Fluid Dynamics Analysis Of An Idealized Modern Wingsuit, Maria E. Ferguson

McKelvey School of Engineering Graduate Student Theses & Dissertations

The aerodynamics of a modern wingsuit has been the subject of very few detailed scientific studies to date. The prevailing design process remains the dangerous “sew and fly” method, in which designs are tested when they are first flown. This study utilizes Computational Fluid Dynamics (CFD) tools to analyze the flow field and aerodynamics of an idealized wingsuit, which is designed using Computer-Aided Design (CAD) modeling. The 3D CAD software Autodesk Inventor is used to create the wingsuit model, which is designed with a Gottingen 228 airfoil cross-section and a relatively large planform of aspect ratio 1.3. The commercial flow …

Numerical Study Of The Aerodynamics Of Dlr-F6 Wing-Body In Unbounded Flow Field And In Ground Effect, Ning Deng

McKelvey School of Engineering Graduate Student Theses & Dissertations

The main focus of this thesis is on the simulation of flow past a three-dimensional wing-body configuration (DLR-F6) in ground effect; a complex 3D wing-body configuration in ground effect has never been analyzed in the aerodynamics literature to date. For the purpose of validation of the simulation approach, computations are performed for the DLR-F6 wing-body in unbounded flow and are compared with the experimental data. The commercial CFD solver ANSYS FLUENT is employed for computations. Compressible Reynolds-Averaged Navier-Stokes (RANS) equations in conjunction with Spalart-Allmaras (SA) and - Shear Stress Transport (SST) turbulence models are solved. The validated code is employed …

Numerical Analysis Of A Flapping Elliptic Flat Plate In Hover: A Study Of Leading Edge Vortex Dynamics, C. Vivek Nair

Mechanical and Aerospace Engineering Theses - Archive

Flapping flight is an area of research that is gaining a lot of prominence in engineering, especially with the increase in interest in applying the flapping mechanism of natural fliers to small scale MAVs. The ongoing contributions to this field include studies finding optimal wing shape, flap frequency, and flap trajectories. Flapping flight is an unsteady aerodynamic mechanism, and consists of 3 interactive forces: delayed stall, rotational circulation, and wake capture. The dominant lift generating mechanism is the leading edge vortex (LEV). Natural fliers optimize their flap to gain maximize LEV stability. For our research we simulate 2 cases of …

The Effect Of Surface Materials And Morphology On Wingsuit Aerodynamics, Timothy Allen Sestak

Doctoral Dissertations and Master's Theses

This study examines the aerodynamic effects of the materials, textiles, and morphologies currently used in wingsuit design and construction. The experiment was a low-speed wind tunnel investigation using a rigid wing with an aspect ratio of 2, a NACA 4418 airfoil cross section and a smooth, polished painted surface as a baseline. The baseline wing was modified by covering the upper and lower surfaces with various textiles currently used in wingsuit construction. This study is the first step in continued research to design and build a wingsuit with superior glide performance compared to current designs. Surface textures and features on …

Interactions Of A Counter-Rotating Vortex Pair At Multiple Offsets, Kyle Forster, Tracie J. Barber, Sammy Diasinos, Graham Doig

Aerospace Engineering

The interactions between two streamwise vortices were investigated by wind tunnel testing of two NACA0012 vanes at various lateral offsets. One vane was spaced 10 chord lengths (C) downstream of the other, with both at an angle of incidence of 8 degrees and a Reynolds number of 7 x 10⁴. The evolution of the vortex pair was observed until 6.5C behind the downstream vane using Particle Image Velocimetry (PIV). It was found that proximity of the upstream vortex to the downstream vane had a significant effect on the rotational rate of the subsequent vortex pair, with far offset …

Effect Of Slot Span On Wing Performance, Juan F. Granizo

Doctoral Dissertations and Master's Theses

This report presents new numerically-derived correlations to estimate the aerodynamic properties of a three-dimensional wing that features a partial to full span fixed slot. Fixed slots have been thoroughly studied in the past with regards to their operation and the relation between slot geometry and wing performance. There have also been many studies on the advantages and disadvantages of tip-slotted wings and the comparison between these and full-slotted wings. Up to this point however, a study on the effects of slot span on wing performance has not been performed. Effect of slot span on wing performance is evaluated in an …