Aerospace Engineering Commons^™

Aerodynamic & Aeroacoustic Performance Of Wind Turbine Blades Featuring Enhanced Flow-Control, Md Zishan Akhter

Dissertations

Wind energy, being one of the cleanest and most sustainable sources, has undergone remarkable growth in recent years due to advancements in aerodynamics and increased power output. The research community is actively pursuing the development of cutting-edge solutions to further optimize wind turbine technology, ensuring its maximum efficiency and revolutionizing the landscape of wind power.
/="/">This research aims to design and develop flow-control devices for wind turbine blades, employing both active and passive control mechanisms, namely morphing trailing-edge and slot-profile, respectively. The objective is to enhance wind turbine performance across a wide range of wind speeds. The morphing trailing-edge …

Augmenting External Surface Pressures’ Predictions On Isolated Low-Rise Buildings Using Cfd Simulations, Md Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

The aim of this paper is to enhance the accuracy of predicting time-averaged external surface pressures on low-rise buildings by utilizing Computational Fluid Dynamics (CFD) simulations. To achieve this, benchmark studies of the Silsoe cube and the Texas Tech University (TTU) experimental building are employed for comparison with simulation results. The paper is structured into three main sections. In the initial part, an appropriate domain size is selected based on the precision of mean pressure coefficients on the windward face of the cube, utilizing Reynolds Averaged Navier-Stokes (RANS) turbulence models. Subsequently, recommendations regarding the optimal computational domain size for an …

Faster, Cheaper, And Better Cfd: A Case For Machine Learning To Augment Reynolds-Averaged Navier-Stokes, John Peter Romano Ii

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, the field of machine learning (ML) has made significant advances, particularly through applying deep learning (DL) algorithms and artificial intelligence (AI). The literature shows several ways that ML may enhance the power of computational fluid dynamics (CFD) to improve its solution accuracy, reduce the needed computational resources and reduce overall simulation cost. ML techniques have also expanded the understanding of underlying flow physics and improved data capture from experimental fluid dynamics.

This dissertation presents an in-depth literature review and discusses ways the field of fluid dynamics has leveraged ML modeling to date. The author selects and describes …

Solving Supersonic Flows Using The Method Of Integral Relations In Python, Eddie Hsieh

Master's Theses

This thesis presents a modern approach to the Method of Integral Relations implemented in the Python programming language. This work is based on South's reports on solving supersonic conical flows and Belotserkovskii's publications on solving supersonic flows over blunt bodies. The Python SciPy library is extensively used in this thesis. A root finder module is used to perform South's solution process, and the Runge-Kutta ODE solver with dense output is implemented to replicate Belotserkovskii's solution process. The implementation of Python makes the development efficient and serves as an open-source framework for future work to build on. This work focuses on …

Innovation For The Air: A Brief History Of Worldwide Aviation, Lauren Plumley

Honors Program: Senior Projects (Public)

The purpose of this report is to present a brief but comprehensive overview of the variety of innovations related to aviation, and to discuss their impact on scientific progress over the course of human history. Relevant discoveries from the fields of physics and aerodynamics, and the numerous technologies built based upon these discoveries, are discussed over a period ranging from ancient times to the twenty-first century. The scope of this report is an overview of the development of powered and unpowered aircraft, including lighter-than-air, heavier-than-air, and aerospace technologies. Aviation developments were generally not limited to one specific country or person, …

Aerodynamic Implications Of A Bio‐Inspired Rotating Empennage Design For Control Of A Fighter Aircraft, Christian R. Bolander

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This dissertation presents an analysis of the aerodynamics for an aircraft using a novel, bio-inspired control system. The control system is a rotating tail, that is inspired by the way in which birds use their tail to control their flight. An aerodynamic model for a baseline aircraft and a bio-inspired variant are created by referencing well-known relationships for the aerodynamics of flight, which are then used to analyze the available flight envelope at which each aircraft can reach two different equilibrium states. An analysis of the total aerodynamic control authority of each aircraft is also included along with a preliminary …

Prediction & Active Control Of Multi-Rotor Noise, Samuel O. Afari

Doctoral Dissertations and Master's Theses

Significant developments have been made in designing and implementation of Advanced Air Mobility Vehicles (AAMV). However, wider applications in urban areas require addressing several challenges, such as safety and quietness. These vehicles differ from conventional helicopter in that they operate at a relatively lower Reynolds number. More chiefly, they operate with multiples of rotors, which may pose some issues aerodynamically, as well as acoustically. The aim of this research is to first investigate the various noise sources in multi-rotor systems. High-fidelity simulations of two in-line counter-rotating propellers in hover, and in forward flight conditions are performed. Near field flow and …

Jet Noise Reduction: A Fresh Start, Christopher K. Tam, Fang Q. Hu

Mathematics & Statistics Faculty Publications

Attempts to reduce jet noise began some 70 years ago. In the literature, there have been many publications written on this topic. By now, it is common knowledge that jet noise consists of a number of components. They possess different spectral and radiation characteristics and are generated by different mechanisms. It appears then that one may aim at the suppression of the noise of a single component instead of trying to reduce jet noise overall. The objective of the present project is to reduce large turbulence structures noise. It is the most dominant noise component radiating in the downstream direction. …

Design And Validation Of An Aerodynamic System For A Formula Sae® Vehicle Using Vehicle Dynamic Simulation And Experimentation, Evan S. Cole

Graduate Theses, Dissertations, and Problem Reports (ETD)

This thesis presents the design, simulation, and experimental validation for the aerodynamic system for a Formula SAE® vehicle. The Society of Automotive Engineers ® (SAE) hosts a collegiate competition annually called Formula SAE® where students design, fabricate, and test a small “formula style” vehicle. The vehicle performs in relatively slow maneuvers, around different courses and tests to evaluate the vehicle’s overall performance. Over the years, collegiate teams have put significant research into the design and manufacturing of the aerodynamics of these vehicles. In order to justify this undertaking for future teams at West Virginia University’s Formula SAE® program, a comprehensive …

Foundations For Finite-State Modelling Of A Two-Dimensional Airfoil That Reverses Direction, Jake Michael Oscar Welsh

McKelvey School of Engineering Graduate Student Theses & Dissertations

Current 3-D finite-state wake models are incapable of simulating a maneuver in which the sign of the free-stream velocity changes direction and the rotor enters its own wake -- as might occur in the case of a helicopter which ascends and then descends. It is the purpose of this work to create a 2-D finite-state wake model which is capable of handling changes in free-stream direction as a precursor to development of a 3-D model that can do the same.

The 2-D finite-state model used for reentry modifications is an existing model created by Peters, Johnson, and Karunamoorthy. By the …

Experimental Characterization Of Additively Manufactured Multi-Feather Wingtip Devices, Patricio Garzon

Doctoral Dissertations and Master's Theses

Soaring birds have evolved to fly for long periods of time without flapping their wings. Inspired by the flight of these birds, the proposed thesis presents an experimental investigation focused on wingtip devices designed based on biomimicry. The overarching engineering objective was to reduce the induced drag as a means to improve the fuel efficiency via these experimental wingtips. An associated secondary objective was to establish a method for manufacturing complex structures suitable for wing tunnel testing. A manufacturing technique that involved using composite weaves to reinforce additively manufactured structures was developed. This technique has the potential to reduce manufacturing …

Aerodynamics And Aeroacoustics Optimization Of Vehicle’S Side Mirror Base And Exhaust Pipe, Moath Nayef Mohamed Zaareer

Theses

This thesis is concerned with studying two different vehicle parts in terms of aerodynamics and aeroacoustics. Two main factors determine the efficiency and luxury of the vehicle, the low aerodynamic forces and low noise emission. The aerodynamic drag coefficient is concerned with how easy a vehicle can travel through the air; the lower the value, the less fuel is needed to move the vehicle forward and less air resistance the vehicle faces. The aerodynamic lift coefficient is related to vehicle ground stability, and the more negative the value is, the higher the vehicle's stability. Moreover, the aeroacoustics is concerned with …

A Study Of Wings With Constant And Variable Sweep For Aerodynamic Efficiency In Inviscid Flow, Bruno Moorthamers

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Wing sweep has been studied by industry and academia since the pioneering days of aviation for both high-speed and low-speed applications. In transonic and supersonic flight regimes it serves to delay the onset of compressibility effects and decrease wave drag. In subsonic conditions, flying wing designs sweep back the main lifting surface in such a way that it can be used for longitudinal stability and control, to allow for the elimination of a traditional empenage. This is desirable because it can decrease the aerodynamic drag. Sweep can also be seen in nature in the wings of birds and fins of …

Influence Of Wing Planform Shape On The Effectiveness Of A Fixed-Slot, Yuan Zhao

Doctoral Dissertations and Master's Theses

This thesis report explores the effect of the Clark-Y wing geometry on lift and drag to use as a reference during aircraft design stage. The different characteristics investigated are fixed slot span, taper ratio, washout, and sweep angle. Plain wings, half slotted wings, and fully slotted wings were built in CATIA with an aspect ratio of 6 and different taper ratio, washout, and sweep angles. Using the CATIA models to generate the 3-D grids in Pointwise. All the simulations were tested in Ansys-Fluent under sea-level conditions with a Reynold number of 609000. The relationships between the aerodynamic characteristics and the …

Aeroelastic Analysis Of Small-Scale Aircraft, Kent Roberts

Master's Theses

The structural design of flight vehicles is a balancing act between maximizing loading capability while minimizing weight. An engineer must consider not only the classical static structural yielding failure of a vehicle, but a variety of ways in which structural deformations can in turn, affect the loading conditions driving those deformations. Lift redistribution, divergence, and flutter are exactly such dynamic aeroelastic phenomena that must be properly characterized during the design of a vehicle; to do otherwise is to risk catastrophe. Relevant within the university context is the design of small-scale aircraft for student projects and of particular consideration, the DBF …

Characterization, Design, And Optimization Of Dual-Purpose Wind Turbines And Frost Protection Fans, Ethan Narad

Master's Theses

This thesis report outlines the creation of a MATLAB tool to design reversible machines that can function as both wind turbines and as agricultural frost protection fans. Frost protection fans are used to prevent crop loss during radiative freeze events during which a temperature inversion is present. Such a dual-purpose machine fundamentally has the constraint that it must use symmetric airfoils, so a suite of tools for automatically designing an optimized wind turbine blade with symmetric airfoils using the Blade Element Momentum (BEM) theory approach is presented. The BEM code is then re-derived and adapted for use with a frost …

Empirical Modeling Of Tilt-Rotor Aerodynamic Performance, Michael C. Stratton

Mechanical & Aerospace Engineering Theses & Dissertations

There has been increasing interest into the performance of electric vertical takeoff and landing (eVTOL) aircraft. The propellers used for the eVTOL propulsion systems experience a broad range of aerodynamic conditions, not typically experienced by propellers in forward flight, that includes large incidence angles relative to the oncoming airflow. Formal experiment design and analysis techniques featuring response surface methods were applied to a subscale, tilt-rotor wind tunnel test for three, four, five, and six blade, 16-inch diameter, propeller configurations in support of development of the NASA LA-8 aircraft. Investigation of low-speed performance included a maximum speed of 12 m/s and …

Integral Boundary Layer Methods In Python, Malachi Joseph Edland

Master's Theses

This thesis presents a modern approach to two Integral Boundary Layer methods implemented in the Python programming language. This work is based on two 2D boundary layer methods: Thwaites' method for laminar boundary layer flows and Head's method for turbulent boundary layer flows. Several novel enhancements improve the quality and usability of the results. These improvements include: a common ordinary differential equation (ODE) integration framework that generalizes computational implementations of Integral Boundary Layer methods; the use of a dense output Runge-Kutta ODE solver that allows for querying of simulation results at any point with accuracy to the same order as …

3d-Printed Morphing Wings For Controlling Yaw On Flying-Wing Aircraft, Benjamin C. Moulton

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The flaps on an airplane wing are used to control the aircraft during flight. These flaps traditionally have at most three articulation or hinge points. Recent studies have shown improved flap efficiency using a conformal flap, which deforms following a curved shape. Much of aircraft improvement comes through increasing its efficiency during flight. This efficiency is generally improved by decreasing the drag force on the aircraft. A potential solution to decrease drag is to remove additional lifting surfaces, such as the horizontal and vertical stabilizer ubiquitous on general aviation aircraft. These additional lifting surfaces are used to trim and control …

Design And Flight-Path Simulation Of A Dynamic-Soaring Uav, Gladston Joseph

Doctoral Dissertations and Master's Theses

We address the development of a dynamic-soaring capable unmanned aerial vehicle (UAV) optimized for long-duration flight with no on-board power consumption. The UAV’s aerodynamic properties are captured with the integration of variable fidelity aerodynamic analyses. In addition to this, a 6 degree-of-freedom flight simulation environment is designed to include the effects of atmospheric wind conditions. A simple flight control system aids in the development of the dynamic soaring maneuver. A modular design paradigm is adopted for the aircraft dynamics model, which makes it conducive to use the same environment to simulate other aircraft models. Multiple wind-shear models are synthesized to …

Plasma Aerodynamics: Experimental Quantification Of The Lift Force Generated On An Airfoil Using Plasma Actuation To Estimate Power Requirements In Small Uav Applications, Getachew Ashenafi

UNLV Theses, Dissertations, Professional Papers, and Capstones

This research addressed the amount of electric power required to induce specific changes in lift force using a NACA 2127 airfoil with a chord length of ~28 mm, connected to a micro load cell, in a wind tunnel of 103 square centimeter cross-section. A DBD plasma actuator supplied by a ZVS driven high voltage pulsed DC circuit, operating at a frequency of 17.4 kHz, was utilized for voltages of up to 5000 V. Two configurations of electrode gapping were compared to determine the efficient use of power. The configuration with a gap of ~1 mm between the upstream and downstream …

Computational Investigation Of Perforated Plate Film Cooling Utilizing Conjugate Heat Transfer, Jonathan Sippel

Doctoral Dissertations and Master's Theses

The accuracy of modern state-of-practice computational fluid dynamics approaches in predicting the cooling effectiveness of a perforated plate film-cooling arrangement is evaluated in ANSYS Fluent. A numerical investigation is performed using the Reynolds Averaged Navier Stokes equations and compared to NASA Glenn’s available Turbulent Heat Flux 4 experimental measurements collected as a part of the Transformational Tools and Technologies Project. A multiphysics approach to model heat conduction through the solid geometry is shown to offer significant improvements in wall temperature and film effectiveness prediction accuracy over the standard adiabatic wall approach. Additionally, localized gradient-based grid adaption is analyzed using the …

State Consistence Of Data-Driven Reduced Order Models For Parametric Aeroelastic Analysis, William C. Krolick, Jung I. Shu, Yi Wang, Kapil Pant

Faculty Publications

This paper investigates the state consistence of parametric data-driven reduced order models (ROMs) in a state-space form obtained by various system identification methods, including autoregressive exogenous (ARX) and subspace identification (N4SID), for aeroelastic analysis in varying flight conditions. The target flight envelop is first partitioned into discrete grid points, on each of which an aerodynamic ROM is constructed using system identification to capture the dependence of the generalized aerodynamic force on the generalized displacement of structural modes. High-fidelity aeroelastic modal perturbation simulations are used to generate the ROM training and verification data. Aerodynamic ROMs not on the grid point are …

Bicycle Wheel Aerodynamics Predictions Using Cfd: Efficiency Using Blade Element Method, Drew Vigne

Honors Undergraduate Theses

The cycling industry has long relied on expensive wind tunnel testing when designing aerodynamic products, particularly in the context of wheels which account for 10 to 15 percent of a cyclist's total aerodynamic drag. With the recent advent of Computational Fluid Dynamics (CFD), the industry now has an economical tool to supplement the wheel design process; however, the complex nature of rotating spoked wheels requires high resolution meshes to model at acceptable fidelity. This research investigates an alternative CFD method that lowers the computational cost of modeling aerodynamic bicycle wheels by modeling spokes using Blade Element Method (BEM). Two CFD …

Identification Of Wind-Induced Hazard Zones Impacting Uas Bridge Inspection, Jack J. Green, John Mott

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned Aerial Systems (UAS) continue to grow in both popularity and utility within the national airspace system. The use of commercial UAS for civil inspection, specifically that of bridge structures, is becoming commonplace among practitioners and academics alike. The development of an integrated bridge-inspection hazard model provides a way for UAS operators to prepare for and respond to changing environmental conditions that could otherwise prevent a successful UAS flight. The interaction of wind-induced airflow with bridge surfaces creates an aerodynamic wake that can result in hazardous conditions for a UAS platform operating in close proximity. An analysis of this airflow …

Comparative Study On Performance Accuracy Of Three Probe And Five Probe Flow Analysers For Wind Tunnel Testing, Akhila Rupesh Ms, J V Muruga Lal Jeyan Dr

International Journal of Aviation, Aeronautics, and Aerospace

In the field of inviscid fluid flow studies, the theoretical concept has to be developed even more. In order to make it possible, it is very important to supplement the concepts with strong experimental results. While performing experimentation, various accepts of design can be determined with factors influencing the and also required modification can be recommended in a more systematic and economic manner. Also, the aim objective of the experiment is to extend the underlying theory and to produce new designs with improvements that can be great support to the advancement in technology. In experimental analysis, wind tunnels are used …

Next-Generation Re-Entry Aerothermodynamic Modeling Of Space Debris Using Machine Learning, Nicholas Sia

Graduate Theses, Dissertations, and Problem Reports (ETD)

The number of resident space objects re-entering the atmosphere is expected to rise with increased space activity over recent years and future projections. Predicting the survival and impact location of the medium to large sized re-entering objects becomes important as they can cause on ground casualties and damage to property. Uncertainties associated with the re-entry process makes necessary a probabilistic approach, which can be computationally expensive when using high-fidelity numerical methods for estimating aerothermodynamic properties. To date, object-oriented analysis is the dominant tool used for atmospheric re-entry modeling and simulation, where aerothermodynamic coefficients are used to determine the risk a …

Field Testing The Effects Of Low Reynolds Number On The Power Performance Of The Cal Poly Wind Power Research Center Small Wind Turbine, John B. Cunningham

Master's Theses

This thesis report investigates the effects of low Reynolds number on the power performance of a 3.74 m diameter horizontal axis wind turbine. The small wind turbine was field tested at the Cal Poly Wind Power Research Center to acquire its coefficient of performance, C­_p, vs. tip speed ratio, λ, characteristics. A description of both the wind turbine and test setup are provided. Data filtration and processing techniques were developed to ensure a valid method to analyze and characterize wind power measurements taken in a highly variable environment. The test results demonstrated a significant drop in the …

Numerical Analysis Of A Circulation Control Wing, Luke W. Bodkin

Master's Theses

The objective of this thesis was to develop an experimental method to research circulation control wings using numerical analysis. Specifically, it is of interest to perform 3D wind tunnel testing on a circulation control wing in the Cal Poly Low Speed Wind Tunnel (CPLSWT). A circulation control wing was designed and analyzed to determine the feasibility of this testing.

This study relied on computational fluid dynamics (CFD) simulations as a method to predict the flow conditions that would be seen in a wind tunnel test. A CFD simulation was created of a wing model in a wind tunnel domain. Due …

A Study Of The Aeroacoustics Of Swept Propellers For Small Unmanned Aerial Vehicles, Arthur David Wiedemann

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, small unmanned aerial vehicles (UAVs) have increased in availability and use in both public and commercial sectors. This increased use of small UAVs or “drones” has the unfortunate consequence of introducing excessive noise into communities where they operate. Implementation of noise reduction methods is necessary if we wish to see expanded use of drones in public areas. With electric propulsion, the primary source of noise is the rotor/propeller used in contemporary multi-rotor configurations. In this thesis, the aerodynamics and acoustic behavior of various swept propellers is examined with computational and experimental methods.

A family of propeller geometries …