Aerospace Engineering Commons^™

Enhancements To Nuclear Thermal Propulsion Rockets, Kimberly Gonzalez

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nuclear thermal rocket propulsion has been proposed as a highly efficient technology for space vehicles traveling from earth orbit to the moon, Mars, and other locations in the solar system. With twice the performance of a chemical rocket, nuclear thermal propulsion (NTP) uses the thrust produced by heating hydrogen gas within a thermal nuclear reactor where the exhaust is then passed through a de Laval nozzle to produce supersonic flow. NTP engines were the subject ofthe NERVA experiments at the Nevada Test Site in the 1970’s, and they produced a specific impulse of up to 900 seconds which is almost …

Controller Platform Design And Demonstration For An Electric Aircraft Propulsion Driv, Rosten Sweeting

Graduate Theses and Dissertations

With the growth in the aerospace industry there has been a trend to optimize the performance of an aircraft by reducing fuel consumption and operational cost. Recent advancements in the field of power electronics have pushed towards the concepts of hybrid electric aircraft also known as more electrical aircrafts. In this work, a custom controller board for an electric aircraft propulsion drive was designed to drive a permanent magnet synchronous motor. Design of the controller board required knowledge of the topology selection and power module selections. Simulations of the system were performed using MATLAB/Simulink to analyze the overall performance of …

Studies Of Multiphase Distribution And Flow In Bubble/ Slurry Bubble Columns With /Without Internals And Advanced Sustainable Construction Materials Using Sophisticated Measurement Techniques, Omar Farid

Doctoral Dissertations

"Bubble/slurry bubble columns have been widely studied and employed as multiphase flow reactors with and without vertical heat-exchanging tubes. In order to understand more deeply the effect of the dense internals on the hydrodynamics of bubble/slurry bubble column, systematic experiments were performed to visualize and quantify using the radioactive particle tracking (RPT) technique. A new methodology for implementing the radioactive particle tracking (RPT) technique has been developed to investigate the effect of the dense internals on the hydrodynamics of the bubble/slurry column reactor. Monte Carlo N-Particle (MCNP) simulation has been implemented to simulate the system to generate a large number …

Ground Station Eat, Utah State University Space Dynamics Laboratory

Space Dynamics Laboratory Publications

Ground Components

Two primary subsystems

•Ground Station(s)

•  May be your own or commercial
• Includes radio(s), antenna(s), rotor, etc.
• Heavily intertwined with satellite communications system
• Influences link budget

•Ground data system

• Your command, control, and telemetry interface
• Operator facing tools
• Front end processor
• Includes computer(s), networking equipment, displays, software tools, etc.
• Directly links to your ground station via network

•Additional ground subsystems could include:

• Payload ground (i.e. optical ground terminal)
• Space comm networks (i.e. Iridium)

Aiaa Design Build Fly Humanitarian Uav, Michael Finigian, Kyle Abbas, David Fryer, Kyle Bartholomew, Jacob Kaufman, William Ryan, Tyler Kwapniowski, Adam Witusik

Discovery Day - Prescott

Every year AIAA issues a challenge to any undergraduate universities willing to meet it: to build an unmanned aerial vehicle (UAV) designed to mission and product characteristics. This year the UAVs are to carry two different payloads in four missions with varying objectives, take-off distances, flight times and flight distances. The two payloads are large plunger syringes and mock vaccine vial packages. The Embry-Riddle Prescott team has decided that the best way to approach these competitions is to split responsibilities evenly between four integrated product teams (IPTs); Aerodynamics, Structures, Propulsion and Missions. In the early stages of the design process, …

Reconnaissance And Documentation (Rad), Cayli Farias, Terra Gordon, Sharik Joseph, Julia Kjenstad, Michael Lauber, Dakota Ross, Logan Hill, Dominick Uzzardo, Richard Harold

Discovery Day - Prescott

The Reconnaissance and Documentation (RAD) mission aims to utilize a Low Earth Orbit satellite using machine learning enabled image recognition and optical remote sensing to observe countries currently experiencing Stage Nine of the United Nations’ Ten Stages of Genocide. The primary objective of the RAD satellite, Leza, is to observe high-risk countries at adequate spatial and temporal resolutions to capture evidence of genocide. The secondary objective of Leza is to process images on-board, so flagged images serving as evidence may be distributed to proper authorities, the United Nations, and mainstream media outlets as soon as possible. Using remote sensing to …

Eaglenautics: Sae Aero West Design Competition Team, Steven Booth, Jessica Millard, Celin Rawther

Discovery Day - Prescott

Eaglenautics is an engineering club affiliated with Embry-Riddle Aeronautical University. Every year, Eaglenautics participates in the SAE Aero West Design Competition. This competition challenges teams to design a competitive R/C scale aircraft from the ground up. Eaglenautics tackles this challenge by using a modified design-build-fly (DBF) process by adding a simulation step after the design step. Simulation software allows for a faster convergence to a design before the build process starts. Eaglenautics utilizes simulation programs like XFLR5 and OpenVSP to aid with the design of the aircraft to save time building multiple aircraft iterations. This process is especially helpful for …

Space Debris Characterization Using Machine Learning Methods, Anson Biggs, Ana Bader-Elenes

Discovery Day - Prescott

Orbital debris is a form of pollution that is growing at an exponential pace and puts current and future space infrastructure at risk. Satellites are critical to military, commercial, and civil operations. Unfortunately, the space they occupy is increasingly becoming more crowded and dangerous, potentially leading to a cascade event that could turn orbit around the Earth into an unusable wasteland for decades proper mitigation is not introduced. Unfortunately, existing models employed by NASA rely on a dataset created from 2D images and are missing many crucial features required for correctly modeling the space debris environment. Our approach uses highresolution …

Team Keryx: Project Lifelink, Robert Belz-Templeman, Evan Hefflin, Jessica Millard, Ariana Anderson, Jacob Hindmarsh, Corey Washburn

Discovery Day - Prescott

First responders such as wildland firefighters, search and rescue crews, and disaster relief workers often operate in cellular-service-denied environments. This lack of long-range communication channels greatly inhibits the spread of vital information. Project LifeLink is Team Keryx’s capstone project designed to solve this issue as well as meeting the course goals of AE 420/421. The course goals for AE 420/421 are to utilize the skills and knowledge obtained in prior classes to design, develop, build, and test an aircraft tailored to a specific challenge. The students will work together in an organized structure and process to prepare them for industry …

Proposal To Augment U.S. Army Lsa And Uars, Cameron Beard

Discovery Day - Prescott

The U.S. Army currently has a gap in its aerial reconnaissance capabilities, with the OH-58D Kiowa completing its phase transition to the AH-64E. Since the Army has done away with its rotary-wing scout aircraft, it currently relies on the AH-64E attack helicopter (an aircraft not designed for such a role), in tandem with UAS RQ- 7Bs and MQ-1C Grey Eagle. These aircraft use the MUM-T (Manned-Unmanned Teaming) system, which allows AH-64E pilots to control the camera and weaponry of the drones while both aircraft are in flight. The draw back to this system lies in two categories; 1) the inability …

Tip Driven Rotor System, Kevin Allyas

Discovery Day - Prescott

The Tip-Driven Rotor System (TDRS) Project is a product designed for KRyanCreative, LLC (KRC), as the basis of a Levitated Annular Rotor System (LARS) for commercial and tactical military vertical takeoff and landing (VTOL) vehicles. Conceptually, this design will greatly increase power density and lift capacity over conventional shaft-centric helicopters. The design also enables variable rotational velocity control that can greatly expand the VTOL flight envelope. The LARS innovatively leverages electromagnetism and superconductive levitation in the transfer of energy from vehicle source to aerodynamic lifting surface. The benefits of LARS include: the reduction of wing tip vortices due to a …

Impact Of Ultrathin Coating Layer On Lithium-Ion Intercalation Into Particles For Lithium-Ion Batteries, Yufang He, Hiep Pham, Xinhua Liang, Jonghyun Park

Chemical and Biochemical Engineering Faculty Research & Creative Works

Ultrathin film coatings on battery materials via atomic layer deposition (ALD) have been demonstrated as an efficient technology for battery performance enhancement. However, the fundamental understanding on lithium intercalation into active materials through the interface between the coating and active materials is unclear, which makes it difficult to optimize ALD coating strategies. Further, like most active materials, a coating layer can undergo volume change during the intercalation process, which can produce detrimental structural changes and mechanical failure of the layer. In this work, first-principles calculations are conducted to reveal the behavior of a coating layer on an active material particle …

The Business Of Moving A Library, Gabriele Hysong

Midwest Business Librarian Summit (MBLS)

No abstract provided.

Proper Orthogonal Decomposition Of Reynolds And Dispersive Stresses In Turbulent Boundary Layers Over Multi-Scale Rough Patches, Catherine Virginia Spivey

Dissertations and Theses

Multi-scale rough patches are present in topologies such as urban canopies (cities) and natural landscapes (forests, ocean floors). The flow over such canopies is three-dimensional, with turbulent structures known as secondary flows present in the boundary layer due to the difference in rough surface heterogeneities. Three dimensional instantaneous velocities are analyzed within the roughness sublayer over three generations of multi-scale rough patches at nine vertical planes using particle image velocimetry obtained experimentally. The secondary structures present in the flow are identified in the form of Reynolds and dispersive fluctuations. Proper orthogonal decomposition is employed to characterize the imprint of the …

Incorporation Of Trajectory Behaviors In The Vicinities Of Different Planetary Moons Using Finite-Time Lyapunov Exponent Maps, David Canales Garcia, Kathleen C. Howell, Elena Fantino

PanaSoMM

There is an increasing interest in future space missions devoted to the exploration of key moons in the Solar system. These many different missions may involve libration point orbits as well as trajectories that satisfy different endgames in the vicinities of the moons. To this end, an efficient design strategy to produce low-energy transfers between the vicinities of adjacent moons of a planetary system is introduced that leverages the dynamics in these multi-body systems. Such a design strategy is denoted as the moon-to-moon analytical transfer (MMAT) method. It consists of a general methodology for transfer design between the vicinities of …

Ci Asteroid Regolith As An In Situ Plant Growth Medium For Space Crop Production, Steven J. Russell, Sherry Fieber-Beyer, Kathryn A. Yurkonis

Biology Faculty Publications

Human expansion into the solar system is currently at the forefront of space research. For our astronauts to survive, they will need to be fed a healthy and nutritious diet on a consistent basis. Right now, our current method of feeding astronauts consists of resupplied prepackaged food from Earth, which is unsustainable for long-term missions. Using planetary resources via in situ resource utilization to grow crops is the next step toward sustainability in space. Asteroids are an abundant space resource and should not be overlooked when considering crewed missions. In particular, the primordial CI carbonaceous asteroids are of interest because …

A Comparative Study On Representativeness And Stochastic Efficacy Of Miniature Tensile Specimen Testing, Sreekar Karnati, Sriram Praneeth Isanaka, Yunlu Zhang, Frank W. Liou, Jason L. Schulthess

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this article, a miniature dog bone tensile coupon design was tested against the existing ASTM standard specimen design. Specimens were prepared from commercially sourced austenitic stainless steel 304 alloy, and a defect-ridden additively manufactured 304L alloy was studied. By utilizing a tensile specimen design that is 1/230th volume of the smallest ASTM E8-04 (2016), Standard Test Methods for Tension Testing of Metallic Materials, dog bone specimen, coupled to a digital image correlation (DIC) setup, case studies were performed to compare tensile property measurements and strain field evolution. Whereas yield strength measurements were observed to be similar, post-yield, the ultimate …

Structural Health Monitoring Of Fatigue Cracks For Steel Bridges With Wireless Large-Area Strain Sensors, Sdiq Anwar Taher, Jian Li, Jong-Hyun Jeong, Simon Laflamme, Hongki Jo, Caroline Bennett, William N. Collins, Austin Downey

Faculty Publications

This paper presents a field implementation of the structural health monitoring (SHM) of fatigue cracks for steel bridge structures. Steel bridges experience fatigue cracks under repetitive traffic loading, which pose great threats to their structural integrity and can lead to catastrophic failures. Currently, accurate and reliable fatigue crack monitoring for the safety assessment of bridges is still a difficult task. On the other hand, wireless smart sensors have achieved great success in global SHM by enabling long-term modal identifications of civil structures. However, long-term field monitoring of localized damage such as fatigue cracks has been limited due to the lack …

Effects Of Pulsatile Flow Rate And Shunt Ratio In Bifurcated Distal Arteries On Hemodynamic Characteristics Involved In Two Patient-Specific Internal Carotid Artery Sidewall Aneurysms: A Numerical Study, Hang Yi, Mark Johnson, Luke C. Bramlage, Bryan Ludwig, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

The pulsatile flow rate (PFR) in the cerebral artery system and shunt ratios in bifurcated arteries are two patient-specific parameters that may affect the hemodynamic characteristics in the pathobiology of cerebral aneurysms, which needs to be identified comprehensively. Accordingly, a systematic study was employed to study the effects of pulsatile flow rate (i.e., PFR−I, PFR−II, and PFR−III) and shunt ratio (i.e., 75:25 and 64:36) in bifurcated distal arteries, and transient cardiac pulsatile waveform on hemodynamic patterns in two internal carotid artery sidewall aneurysm models using computational fluid dynamics (CFD) modeling. Numerical results indicate that larger PFRs can cause higher wall …

Behavioral Intention Factors For Prescription Deliveries By Small Unmanned Aircraft In Rural Communities, Sarah M. Talley

Doctoral Dissertations and Master's Theses

Nearly half of the U.S. population regularly use and depend on prescription medications; however, pharmacy availability and access to pharmacy services are often lacking, particularly in rural communities. In an effort to meet local healthcare needs, delivery by sUAS is proposed to ensure the nearly 60 million rural residents have access to their prescription medications.

As an emerging technology with little research into home delivery applications, the successful implementation of sUAS for prescription medication delivery requires public acceptance and positive behavioral intention toward its use. At the time of the current research, no prior studies have specifically focused on the …

Experimental Characterization Of Additively Manufactured Multi-Feather Wingtip Devices, Patricio Garzon

Doctoral Dissertations and Master's Theses

Soaring birds have evolved to fly for long periods of time without flapping their wings. Inspired by the flight of these birds, the proposed thesis presents an experimental investigation focused on wingtip devices designed based on biomimicry. The overarching engineering objective was to reduce the induced drag as a means to improve the fuel efficiency via these experimental wingtips. An associated secondary objective was to establish a method for manufacturing complex structures suitable for wing tunnel testing. A manufacturing technique that involved using composite weaves to reinforce additively manufactured structures was developed. This technique has the potential to reduce manufacturing …

Effect Of Spray Rails On Takeoff Performance Of Amphibian Aircraft, Soham Bahulekar

Doctoral Dissertations and Master's Theses

Amphibian aircraft have seen a rise in popularity in the recreational and utility sectors due to their ability to take off and land on both land and water, thus serving a myriad of purposes such as aerobatics, surveillance, and firefighting. The design of such seaplanes requires to be both aerodynamically and hydrodynamically efficient, especially during the takeoff phase. In the past, naval architects have implemented ways to make boats, yachts, and large ships more efficient; one of them being the addition of chine strips and spray rails on the hull. This thesis study explores the possibility of implementing spray rails …

Synthetic Gecko Inspired Dry Adhesive Through Two-Photon Polymerization For Space Applications, Zefu Ren

Doctoral Dissertations and Master's Theses

This work aims to develop an advanced and cost-effective fabrication process to produce a simplified gecko-inspired microstructure with two-photon polymerization and polymer molding, aimed to improve the adhesive properties of microstructures. Such adhesive microstructures can be implemented for multi-purpose adhesive grasping devices, which have recently gained significant interest in the space exploration sector. Previous gecko-inspired microstructures were reviewed, and the new gecko-inspired microstructures have been developed with the adaptation of additive manufacturing methods for facile fabrication. The examined microstructures in this thesis were the tilted mushroom-shaped and wedge-shaped designs, which could both maximize adhesion by shearing the micropillars toward the …

Optimization Of Rover Wheel Geometries For Planetary Missions, Nikita Amberkar

Doctoral Dissertations and Master's Theses

Rovers have been launched into space for exploration of the Moon and Mars to collect samples of rock and soil. To continue the explorations, the rovers need to have reliable wheels to drive around. However, due to the soil being soft, the wheels on the rover start to lose traction and the wheels sink while driving to various locations. Previous work in this field has been done experimentally or with the use of simulations. Only a few references report the effect of uncertainties in grouser simulation on the traction efficiency. The objective of this work was to (a) Understand the …

Quasi-Static Structural Analysis Of An Experimental Aircraft Wing, Scott Bender

Doctoral Dissertations and Master's Theses

In this report, a quasi-static load analysis is conducted on an experimental light sport aircraft wing via a whiffletree bending test. This report will discuss the loads present on the aircraft during straight level flight at a speed of 82 knots equivalent air speed. Flight load calculations are described along with the design of the whiffletree and mounting structures utilized for applying the distributed point loads. Initial finite element analysis is performed on the wing structure to determine critical strain locations and optimal sensor distribution. Subsequent mechanical experimentations are performed using a bending test to measure the strain at critical …

A Patient Risk Minimization Model For Post-Disaster Medical Delivery Using Unmanned Aircraft Systems, Mark J. Simpson

Doctoral Dissertations and Master's Theses

The purpose of this research was to develop a novel routing model for delivery of medical supplies using unmanned aircraft systems, improving existing vehicle routing models by using patient risk as the primary minimization variable.

The vehicle routing problem is a subset of operational research that utilizes mathematical models to identify the most efficient route between sets of points. Routing studies using unmanned aircraft systems frequently minimize time, distance, or cost as the primary objective and are powerful decision-making tools for routine delivery operations. However, the fields of emergency triage and disaster response are focused on identifying patient injury severity …

Numerical Study Of The Effects Of Injector Geometry On The Performance Of Rotating Detonation Engines, Xavier Roy

Theses and Dissertations

A study of the impact of injector geometry on the performance of rotating detonation engines is performed. A numerical scheme is developed to represent the rotating detonation engine physics. In order to simulate the interaction between the chamber and the injectors, a multizone capability is implemented inside the numerical tool. The model is calibrated to represent a hydrogen-air detonation. The rotating detonation engine annular chamber is unwrapped and studied as a two-dimensional planar domain with a periodic boundary condition. Several numerical experiments are conducted. In particular, injection parameters are examined, such as the injector inflow to channel area ratio, injection …

Exploring Passive Flow Control Techniques Applied To A Supersonic Multistream Rectangular Nozzle, Emma Dawn Gist

Dissertations - ALL

Passive control techniques are applied experimentally to examine different aspects of a supersonic multistream rectangular nozzle representing a modern airframe-integrated variable cycle engine. The flow is comprised of a core stream (M = 1.6) and bypass (M = 1.0) that merge behind a splitter plate and exit through a Single Expansion Ramp Nozzle (SERN) onto an aft-deck. Previous efforts for the nominal nozzle configuration have shown that an instability initiated at the splitter plate trailing edge (SPTE) influences the effectiveness of the third stream as a barrier for the aft-deck and persists through the entire do- main due to its …

Propellant Optimization For A Pulsed Solid Propellant Thruster System For Small Satellites, Timothy Aaron Blackman

Theses and Dissertations

CubeSats have historically been used mostly for education, technology demonstration, remote sensing, and amateur radio relay applications. Yet with increased maneuvering capability, they can become effective tools in on-orbit servicing and space debris removal. To make this a reality, CubeSats must be enabled to perform effective rendezvous and proximity operations with non-cooperative client objects, requiring a high-thrust propulsion system. As CubeSats are inherently constrained in their volume and mass, any propulsion system must feature a high specific impulse to minimize the propellant mass requirement. As CubeSats are commonly launched as secondary payload, the use of pressurized propellant tanks is typically …

Electromagnetic Interference Shielding Effectiveness Of A Layered System Consisting Of A Carbon Nano-Reinforced Polymer Composite Coated With Metal Oxide And Graphite, Veronica Montserrat Serrato

Theses and Dissertations

In this study, the electromagnetic interference (EMI) shielding effectiveness (SE) of vapor grown carbon nanofiber (VGCNF) reinforced polyvinylidene difluoride (PVDF) composite and PVDF/VGCNF thermally sprayed with magnetite (Fe3O4) and graphite has been investigated. EMI SE evaluations were performed in the frequency range of 30 kHz-1.5 GHz. The developed nanocomposite (NC) system was fabricated by high shear mixing using a Banbury type mixer. The material was then subjected to compression molding. Subsequently, the films were thermally sprayed using Fe3O4/graphite powder. The NC and coated NC films had average thicknesses of 0.82 mm and 0.93 mm, respectively. The NC films were subjected …