Aerospace Engineering Commons^™

Experimental Development Of Compressor And Turbine Performance Maps For Turbomachinery, Michael W. Green

Aerospace Engineering

Turbomachinery performance maps are used to reveal the on and off design performance of compressors and turbines. These maps plot the component’s pressure ratio versus the corrected flow rate for multiple engine rotor speeds. In this experiment, a Boeing T50-BO-8A converted turbojet engine was operated at a wide variety of rotor speeds with orifice plates of different sizes to vary the flow rate. The corrected flow rate through the turbojet ranged from 1.32 to 2.55 lb/s. The pressure ratios for the compressor and turbine ranged from 2.0 to 4.3 and from 1.7 to 4.3, respectively. The resulting performance maps showed …

Section Abstracts: Aeronautical And Aerospace Sciences

Virginia Journal of Science

Abstracts of the Aeronautical and Aerospace Science Section for the 88th Annual Meeting of the Virginia Academy of Science, May 20-21, 2010, James Madison University, Harrisonburg, VA.

Neural Network Fatigue Life Prediction In Notched Aluminum Specimens From Acoustic Emission Data, Muhammed Arif Okur

Master's Theses - Daytona Beach

This purpose of this research was to identify fatigue crack growth and predict failure for 7075-T6 aluminum notched bars under uniaxial tensile loading using acoustic emission (AE) data. The experiments performed in this study extend the results obtained by previous researchers who used maximum cyclic loads of 4,000, 3,000, and 2,000 pounds at a stress ratio of R = 0.0 and a frequency of 1 Hz to perform the fatigue tests. For this research the cyclic load remained at 2,000 pounds, but an additional ten specimens were tested in order to increase the amount of AE data available to the …

Numerical Simulation Of A Liquid Jet Atomization And Break-Up Using Ansys-Cfx 12.0, Yash Akhil Bhatt

Master's Theses - Daytona Beach

Break-up and atomization characteristics of JetA liquid fuel were investigated numerically. The results have been compared to various experimental results to evaluate the accuracy of the numerical model. The CFD code ANSYS-CFX 12.0 was used to carry out the steady state analysis at different time scales. A comparison between the atomization characteristics of a pressure jet atomizer and an air-blast atomizer is shown. By employing a Lagrangian particle tracking method to track the path of the liquid particles, the liquid jet/spray phenomena was studied in light of low and high back pressure environments. The 'BLOB' primary atomization model and the …

Assessing The V2-F Turbulence Models For Circulation Control Applications, Travis M. Storm

Master's Theses

In recent years, airports have experienced increasing airport congestion, partially due to the hub-and-spoke model on which airline operations are based. Current airline operations utilize large airports, focusing traffic to a small number of airports. One way to relieve such congestion is to transition to a more accessible and efficient point-to-point operation, which utilizes a large web of smaller airports. This expansion to regional airports propagates the need for next-generation low-noise aircraft with short take-off and landing capabilities. NASA has attacked this problem with a high-lift, low-noise concept dubbed the Cruise Efficient Short Take-Off and Landing (CESTOL) aircraft. The goal …

High Order Finite Elements For Lagrangian Computational Fluid Dynamics, Truman Everett Ellis

Master's Theses

A general finite element method is presented to solve the Euler equations in a Lagrangian reference frame. This FEM framework allows for separate arbitrarily high order representation of kinematic and thermodynamic variables. An accompanying hydrodynamics code written in Matlab is presented as a test-bed to experiment with various basis function choices. A wide range of basis function pairs are postulated and a few choices are developed further, including the bi-quadratic Q2-Q1d and Q2-Q2d elements. These are compared with a corresponding pair of low order bi-linear elements, traditional Q1-Q0 and sub-zonal pressure Q1-Q1d. Several test problems are considered including static convergence …

Optimization Of The Odu Maglev System Ridership Performance, Eric Salvador M. De Leon

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this research is to optimize the ODU People Mover project (Maglev vehicle) by providing a valid estimate of system "ridership" performance via modeling and simulation. The results considered both service parameters and cost of system operation. The system studied three stations on a line with no closed loop which was evidently unique, but the methods and approaches used for the problem can be applied to any transportation system or layout.

To achieve this objective -- design constraints and other relevant system inputs were identified that impacted the design parameters of the transportation system and permitted assessment of …

Hybrid Intelligent Optimization Methods For Engineering Problems, Yasin Volkan Pehlivanoglu

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of optimization is to obtain the best solution under certain conditions. There are numerous optimization methods because different problems need different solution methodologies; therefore, it is difficult to construct patterns. Also mathematical modeling of a natural phenomenon is almost based on differentials. Differential equations are constructed with relative increments among the factors related to yield. Therefore, the gradients of these increments are essential to search the yield space. However, the landscape of yield is not a simple one and mostly multi-modal. Another issue is differentiability. Engineering design problems are usually nonlinear and they sometimes exhibit discontinuous derivatives for …

Acoustic Emission Fatigue Crack Monitoring Of A Simulated Aircraft Fuselage Structure, Jeremy James Lucas

Doctoral Dissertations and Master's Theses

The purpose of this research was to replicate the fatigue cracking that occurs in aircraft placed under loads from cyclical compression and decompression. As a fatigue crack grows, it releases energy in the form of acoustic emissions. These emissions are transmitted through the structure in waves, which can be recorded using acoustic emission (AE) transducers. This research employed a pressure vessel constructed out of aluminum and placed under cyclical loads at 1 Hz in order to simulate the loads placed on an aircraft fuselage in flight. The AE signals were recorded by four resonant AE transducers. These were placed on …

Stability Of Fully Nonlinear Stokes Waves On Deep Water: Part 1. Perturbation Theory, Shahrdad Sajjadi, David L. Ross

Publications

We consider a full set of harmonics for the Stokes wave in deep water in the absence of viscosity, and examine the role that higher harmonics play in modifying the classical Benjamin-Feir instability. Using a representation of the wave coefficients due to Wilton, a perturbation analysis shows that the Stokes wave may become unbounded due to interactions between the N^th harmonic of the primary wave train and a set of harmonics of a disturbance. If the frequency of the n^th harmonic is denoted Ꙍ_n = Ꙍ(1 ± ꭉ) then instability will occur if

√2 k n^{n …}

Estimation And Management Of Observation Time For Low Earth Orbit Satellite, Serdar Cagirdar

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, time to observation for a generic low Earth orbit satellite after being tasked for reconnaissance of a particular surface target is investigated. A closed-form Keplerian propagation of the nominal orbit is used as the process for computing a solution to the time to observation for both scanning and staring sensors. Orbital maneuvers to reach the target sooner than the nominal trajectory are also considered. In this way time to observation is managed. Lambert's problem, which is used to determine an orbit of a satellite from two position vectors and the time of flight between them, is used …

An Experimental Study Of The Near Wake Field Behind A Propeller Aircraft, Hasan Ozgur Yavas

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents an experimental study of the wake behind a generic, high wing, half model of a propeller driven aircraft. Wake surveys are performed at a free stream velocity of 9m/s in the Old Dominion University Low-Speed Wind Tunnel. The objective of the study is understanding the general characteristics of development and interaction of tip vortices, flap vortices, and propeller vortices in the wake of a two propeller aircraft. The measurements in the wake were obtained by using hot-wire anemometry. Measurements were made both using single wire and X-wire probes mounted on a traverse mechanism on three planes behind …

Analysis Of Helicopter Downwash/Frigate Airwake Interaction Using Statistically Designed Experiments, Yavuz Nacakli

Mechanical & Aerospace Engineering Theses & Dissertations

A research program to investigate helicopter downwash/frigate airwake interaction has been initiated using a statistically robust experimental program featuring Design of Experiments. Engineering analysis of the helicopter/frigate interface is complicated by the fact that two flowfields become inherently coupled as separation distance decreases. The final objective of this work is to develop experimental methods to determine when computer simulations need to include the effects of a coupled flowfield versus using a simplified representation by superposing the velocity fields of the individual flowfields. The work presented was performed in the Old Dominion University Low Speed Wind Tunnel using a simplified 1/50 …

Reducing Orbit Covariance For Continuous Thrust Spacecraft Transfers, Scott Zimmer, Oscar Ocampo, Robert H. Bishop

Mechanical Engineering Faculty Research and Publications

The calculus of variations is used to develop the necessary theory and derive the optimality conditions for a spacecraft to transfer between a set of initial and final conditions, while minimizing a combination of fuel consumption and a function of the estimation error covariance matrix associated with the spacecraft state. The theory is developed in a general manner that allows for multiple observers, moving observers, covariance associated with an arbitrary frame, a wide variety of observation types, multiple gravity bodies, and uncertainties in the spacecraft equations of motion based on the thrusting status of the engine. A series of example …

Modeling And Analysis Of Low Earth Orbit Satellite And Ground Station Data Exchange Topology, Ersin Kocoglu

Mechanical & Aerospace Engineering Theses & Dissertations

In order to utilize space effectively, the primary function of satellite control in orbit around the Earth must be accomplished. This controlling process includes two main segments, ground stations serving as the controller units and orbiting satellites as the units to be controlled. This thesis explores a topological data exchange model that contains one satellite and multiple ground stations. The model is implemented in digital computer software. This model has multiple purposes and can be used to simulate satellite passes over ground stations and can also be used to predict communication time and the amount of transferred data. The model …

Multi-Element Airfoil Optimization Using Computational Fluid Dynamics, Mustafa Kubilay Ictuzer

Mechanical & Aerospace Engineering Theses & Dissertations

High-lift systems are frequently used on commercial transport aircrafts to obtain low speed performance, in terms of take-off and landing field lengths and approach speed. To maximize the take-off and landing performance within the critical restrictions required by the new generation transport wing designs, enhanced high-lift technologies are needed. Moreover, the economic realities faced by the airlines require a design that is mechanically simple and effective. These facts lead us to the optimization of the high lift systems.

Optimizing a high-lift system improves an aircraft's take-off and landing performance. The weight of the system, the advantages and the disadvantages all …

Non Bayesian Conditioning And Deconditioning, Jean Dezert, Florentin Smarandache

Branch Mathematics and Statistics Faculty and Staff Publications

In this paper, we present a Non-Bayesian conditioning rule for belief revision. This rule is truly Non-Bayesian in the sense that it doesn’t satisfy the common adopted principle that when a prior belief is Bayesian, after conditioning by X, Bel(X|X) must be equal to one. Our new conditioning rule for belief revision is based on the proportional conflict redistribution rule of combination developed in DSmT (Dezert-Smarandache Theory) which abandons Bayes’ conditioning principle. Such Non-Bayesian conditioning allows to take into account judiciously the level of conflict between the prior belief available and the conditional evidence. We also introduce the deconditioning problem …

Follow Up Nucleate Boiling On-Flight Experiment, Andrew Fassmann

Presentations

No abstract provided.

Compression Testing Of Composite Laminated Foam Under Thermal Loading And With Central Holes, Dominic Surano, Jonathan Russo, Daniel Leighton

Aerospace Engineering

A study was conducted to investigate the effect of heat on composite sandwich plates, fabricated with the vacuum resin infusion process, with center holes of varying diameters. The study involved conventional notched specimens and notched specimens with shear keys, both of which were subjected to monotonic inplane compression loading. Hole diameter was be varied from one to four inches in one inch increments. Loading rate was applied using the Instron machine at one millimeter per minute. The diameter of the shear key around the holes varied from one inch to four inches in one inch increments. The specimens were placed …

Global Navigation Satellite System Software Defined Radio, Jason M. Mcginthy

Theses and Dissertations

The GNSS world is quickly growing. The United States’ GPS, the European Union’s Galileo, China’s Compass, and Russia’s GLONASS systems are all developing or modernizing their signals, and there will soon be more navigation satellites in space than ever before. The goal of this research was to develop an initial capability for an AFIT GNSS software receiver. This software receiver is intended to be used for research purposes at the Advanced Navigation Technology (ANT) Center. First a GPS-only software receiver was built. It successfully acquired, tracked, and provided reasonable position estimates. Next, the receiver was successfully modified to acquire and …

Artificial Inhomogeneous Tapered Impedance Sheet Characterization And Applications, Jeffrey P. Massman

Theses and Dissertations

The ability to manipulate a complex impedance sheet about a PEC or general dielectric cylinder of arbitrary diameter to control the overall scattering characteristics at particular angles for shielding or scattering applications is presented. It is shown that with the capability to readily control both the real and imaginary components of a percolated lossy film's effective impedance, specific impedance distributions can be obtained to effectively direct the overall nulls in the bistatic scattering pattern. The exact approach only requires negligible truncation error of the matrix solution and can be applied to cylinders of arbitrary size. This approach relies on general …

Monocular Vision Localization Using A Gimbaled Laser Range Sensor, Don J. Yates

Theses and Dissertations

There have been great advances in recent years in the area of indoor navigation. Many of these new navigation systems rely on digital images to aid an inertial navigation estimates. The Air Force Institute of Technology (AFIT) has been conducting research in this area for a number of years. The image-aiding techniques are centered around tracking stationary features in order to improve inertial navigation estimates. Previous research has used stereo vision systems or terrain constraints with monocular systems to estimate feature locations. While these methods have shown good results, they do have drawbacks. First, as unmanned exploration vehicles become smaller …

Aiding Gps With Additional Satellite Navigation Services, Yasin A. Mutlu

Theses and Dissertations

In modern warfare navigation services are very important. GPS is currently providing service for accurate navigation, except in some areas, especially urban areas, where GPS signals cannot always be tracked by users. In these cases some additional navigation support could be provided by other global navigation satellite systems. If GPS is combined with other navigation systems than the navigation gap will be minor. In this thesis, the effect of combining GPS with other satellite navigation systems, specifically GLONASS, Galileo and Compass, is evaluated in terms of availability and position dilution of precision (PDOP) values. First, satellite constellations are simulated in …

Consideration Of Wear Rates At High Velocity, Chad S. Hale

Theses and Dissertations

The development of the research presented here is one in which high velocity relative sliding motion between two bodies in contact has been considered. The experimental results of a VascoMax 300 maraging steel slipper sliding on an AISI 1080 steel rail during a January 2008 sled test mission were considered for the determination of high velocity wear rates. The numerical model, based on a metallographic study of a test slipper, contained all of the physical features present in order to adequately characterize high velocity wear rates. Two-dimensional, plane strain models have been implemented in the explicit finite element code, ABAQUS. …

Assembly, Integration, And Test Methods For Operationally Responsive Space Satellites, Lisa A. Baghal

Theses and Dissertations

Current government and industry standards in spacecraft testing result in an Assembly, Integration, and Test (AIT) timeline greater than six months. These standards will not support the vision of Operationally Responsive Space (ORS) to deploy a satellite within six days to fill an urgent need. Using the Air Force Research Laboratory’s Plug-and-Play Satellite (PnPSat), multiple Rapid AIT trials were conducted. By exercising the AIT process with various spacecraft configurations and personnel, methods for reducing or modifying traditional testing regimen were investigated.

Development Of A Flapping Wing Design Incorporating Shape Memory Alloy Actuation, Jeffrey A. Barrett

Theses and Dissertations

This research sought to validate a proof of concept regarding shape memory alloy actuation of a flapping-wing blimp. Specimen wires were subjected to cyclic voltage at increasing frequencies to quantify expected strains. A laser vibrometer captured 2048 sample velocities during single contraction and elongation cycles, and the resulting samples were used to calculate displacements. Displacements were determined ten times for each specimen and frequency to compute averages. Subsequently, a circumventing frame was designed to encase a blimp envelope and provide support for a flapping motion actuation system. Contraction of shape memory wire translated force to the flapping mechanism via bellcranks, …

Verification Of Kam Theory On Earth Orbiting Satellites, Christian L. Bisher

Theses and Dissertations

This paper uses KAM torus theory and Simplified General Perturbations 4 (SGP4) orbit prediction techniques compiled by Dr. William Wiesel and compares it to Analytical Graphics ® Incorporated (AGI) Satellite Toolkit ® (STK) orbit data. The goal of this paper is to verify KAM torus theory can be used to describe and propagate an Earth satellite orbit with similar accuracy to existing general perturbation techniques. Using SGP4 code including only truncated geopotential effects, KAM torus generating code, and other utilities were used to describe a particular satellite orbit as a torus and then propagate the satellite using traditional and KAM …

Experiments With Geometric Non-Linear Coupling For Analytical Validation, Jonathan D. Boston

Theses and Dissertations

This study was focused on obtaining accurate experimental data for the validation of the geometrically exact beam theory from a series of experiments in which high quality surface shape and deflection data was collected. Many previous experiments have experienced issues with data collection or test articles which the researchers were unable to overcome. The test program was performed in two stages: qualification and joined-wing. The qualification stage validated the experimental procedures on simple 72 in long aluminum beams with 8 in x 0.5 in cross-sections. The joined-wing stage was the primary experiment focused on obtaining quality data for use in …

Gravity Gradiometry And Map Matching: An Aid To Aircraft Inertial Navigation Systems, Anthony J. Degregoria

Theses and Dissertations

Inertial navigation systems (INS) offer passive, all-weather, and undeniable navigation information, which military customers often view as especially appealing strengths. Unfortunately, Airmen and engineers still struggle with INS’s drifting position errors, and navigation aids generally detract from INS’s strengths. At this year’s Air, Space, and Cyberspace in the 21st Century Conference, the Chief of Staff of the Air Force identified the Global Positioning System (GPS) as a widely-known and exploitable vulnerability, saying that it’s critical the Joint force reduce GPS dependence. Recent advances provide an opportunity for gravity gradient instruments (GGI), which measure spatial derivatives of the gravity vector, to …

Effectsof Prior Aging At 260 °C In Argon On Inelastic Deformation Behavior Of Pmr-15 Polymer At 260 °C: Experiment And Modeling, Bradley K. Diedrick

Theses and Dissertations

The purpose of this research was to investigate the inelastic deformation behavior of PMR-15 neat resin, a high-temperature polymer, at 260 °C. The experimental program was designed to explore the influence of strain rate on loading and unloading behaviors. In addition, the effect of prior strain rate on creep, relaxation, and recovery responses was evaluated. The material exhibits positive, nonlinear strain rate sensitivity in monotonic loading. Early failures occur before fully establishing inelastic flow. The creep, relaxation, and recovery responses are significantly influenced by prior strain rate. The experimental results suggest the behavior of PMR-15 at 260 °C can be …