Aerospace Engineering Commons^™

Aerothermodynamic Analysis Of A Mars Sample Return Earth-Entry Vehicle, Daniel A. Boyd

Mechanical & Aerospace Engineering Theses & Dissertations

Because of the severe quarantine constraints that must be imposed on any returned extraterrestrial samples, the Mars sample return Earth-entry vehicle must remain intact through sample recovery. Vehicles returning on a Mars-Earth trajectory will attain velocities exceeding any that have been experienced by prior space exploration missions, with velocities approaching 14 km/s. Velocities as high as these will encounter significant heating during atmospheric re-entry to Earth.

The purpose of this study has been to systematically investigate the aerothermodynamic challenges that will result from a Mars sample return, Earth-entry vehicle design. The goal was to enable efficient estimation of maximum stagnation …

A Cost Effective Design For A Propeller Thrust/Torque Balance, Nicholas Barrett Sadowski

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel balances are used with aircraft models, propellers, and components to measure applied forces and moments. The design and manufacture of a balance is often for a specific test, test article and conditions. This paper discusses the theory, design, calibration, and testing of a new small propeller balance for use in a low-speed wind tunnel. The new balance is named the ODU15X15.

Theory discussed herein covers how the two measurement components, thrust and torque, affect the balance design. These loads generate strains which are in turn read by strain gages arranged in Wheatstone bridges. The design follows well known …

Distributed Sensing And System Identification Of Cantilever Beams And Plates In The Presence Of Weak Nonlinearities, Patrick Sean Heaney

Mechanical & Aerospace Engineering Theses & Dissertations

While the mathematical foundation for modal analysis of continuous systems has long been established, flexible structures have become increasingly widespread and developing tools for understanding their mechanics has become increasingly important. Cantilever beams and plates, in particular, have been extensively studied due to their practical importance as approximations of more complex structures. The focus of this thesis is on understanding the dynamics of vibrating cantilever beams and plates through analytical and experimental investigation. Various models for the mechanics of these structures, of varying physical fidelity, are described and compared. A fiber optic sensing system is utilized to experimentally acquire distributed …

Volterra Series Approximation For Multi-Degree Of Freedom, Multi-Input, Multi-Output, Aircraft Dynamics, Alexander J. Chen

Mechanical & Aerospace Engineering Theses & Dissertations

An analytical model of a second order system is extended from a single-axis framework, to a multi-axis, multi-degree of freedom framework for a multiple input, multiple output system. This mathematical model is built from the variational approach of the Volterra series representation of nonlinear systems. The new representation describes the second order, oscillatory natural modes of a system, and shows how to organize the Volterra terms in intuitive ways. The constructed mathematical model aims to establish an organization of the Volterra kernels to allow for analytical cause and effect type analysis on system behavior.

To demonstrate the accuracy of the …

Design And Implementation Of An Artificial Neural Network Controller For Quadrotor Flight In Confined Environment, Ahmed Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

Quadrotors offer practical solutions for many applications, such as emergency rescue, surveillance, military operations, videography and many more. For this reason, they have recently attracted the attention of research and industry. Even though they have been intensively studied, quadrotors still suffer from some challenges that limit their use, such as trajectory measurement, attitude estimation, obstacle avoidance, safety precautions, and land cybersecurity. One major problem is flying in a confined environment, such as closed buildings and tunnels, where the aerodynamics around the quadrotor are affected by close proximity objects, which result in tracking performance deterioration, and sometimes instability. To address this …

Human-Robot Collaborative Force-Controlled Micro-Drilling For Advanced Manufacturing And Medical Applications, Parimal Mahesh Prajapati

Mechanical & Aerospace Engineering Theses & Dissertations

Robotic drilling finds applications in diverse fields ranging from advanced manufacturing to the medical industry. Recent advances in low-cost, and human-safe, collaborative robots (e.g., Sawyer) are enabling us to rethink the possibilities in which robots can be deployed for such tedious and time-consuming tasks. This thesis presents a robotic drilling methodology with features of force-control enabled micro-drilling and human-robot collaboration to reduce programming efforts and enhance drilling performance. A Sawyer robot from Rethink Robotics, which offers safe physical interactions with a human co-worker, kinesthetic teaching, and force control, is used as the test bed. The robot’s end-effector was equipped with …

A Monolithic Internal Strain-Gage Balance Design Based On Design For Manufacturability, Thomas Ladson Webb Iii

Mechanical & Aerospace Engineering Theses & Dissertations

This paper proposes an alternative approach to internal strain-gage balance design driven by Design for Manufacturability (DFM) principles. The objective of this research was a reduction in fabrication time and, subsequently, cost of a balance by simplifying its design while maintaining basic stiffness and sensitivity. Traditionally, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) balance designs have relied on Electro-Discharge Machining (EDM), which is a precise but slow and, therefore, expensive process. EDM is chosen due to several factors, including material hardness, surface finish, and complex geometry, including blind cuts. The new balance design objectives require no …

Gust Alleviation System For General Aviation Aircraft, Lucas Coleman Mills

Mechanical & Aerospace Engineering Theses & Dissertations

A designed control motion scheme to improve passenger comfort in general aviation aircraft by reducing normal acceleration and pitch rate due to turbulence is investigated. An aerodynamic math model is created for ViGYAN’s Active Ride Improvement System flight article, a one-eighth scale Pilatus Porter PC-6 with conventional forward main wing, aft horizontal and vertical tails, and a single engine with tractor configuration. The test article incorporates a full-span gust flap and forward mounted gust sensor to mechanize the gust alleviation control system, and these features are present in the dynamic model. The model is a two degree of freedom linear …

Computational Methods For Nonlinear Systems Analysis With Applications In Mathematics And Engineering, Geoffrey Kenneth Rose

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation into current methods and new approaches for solving systems of nonlinear equations was performed. Nontraditional methods for implementing arc-length type solvers were developed in search of a more robust capability for solving general systems of nonlinear algebraic equations. Processes for construction of parameterized curves representing the many possible solutions to systems of equations versus finding single or point solutions were established. A procedure based on these methods was then developed to identify static equilibrium states for solutions to multi-body-dynamic systems. This methodology provided for a pictorial of the overall solution to a given system, which demonstrated the possibility …

Development Of A Data Acquisition System For Unmanned Aerial Vehicle (Uav) System Identification, Donald Joseph Lear

Mechanical & Aerospace Engineering Theses & Dissertations

Aircraft system identification techniques are developed for fixed wing Unmanned Aerial Vehicles (UAV). The use of a designed flight experiment with measured system inputs/outputs can be used to derive aircraft stability derivatives. This project set out to develop a methodology to support an experiment to model pitch damping in the longitudinal short-period mode of a UAV. A Central Composite Response Surface Design was formed using angle of attack and power levels as factors to test for the pitching moment coefficient response induced by a multistep pitching maneuver.

Selecting a high-quality data acquisition platform was critical to the success of the …

Investigation, Modeling And Validation Of Digital Bridge For A New Generation Hot-Wire Anemometer, Karthik Kamalakar Joshi

Mechanical & Aerospace Engineering Theses & Dissertations

The Digital Bridge Thermal Anemometer (DBTA) is a new generation anemometer that uses advanced electronics and a modified half-Wheatstone bridge configuration, specifically a sensor and a shunt resistor in series. This allows the miniaturization of the anemometer and the communication between host computer and anemometer is carried out using serial or ethernet which eliminates the noise due to the use of long cables in conventional anemometer and the digital data sent to host computer is immune to electrical noise. In the new configuration the potential drop across a shunt resistor is used to control the bridge.

This thesis is confined …

A Low Cost Inflatable Cubesat Drag Brake Utilizing Sublimation, Adam Charles Horn

Mechanical & Aerospace Engineering Theses & Dissertations

The United Nations Inter-Agency Debris Coordination Committee has adopted a 25-year post-mission lifetime requirement for any satellite orbiting below 2000 km in order to mitigate the growing orbital debris threat. Low-cost CubeSats have become important satellite platforms with startling capabilities, but this guideline restricts them to altitudes below 600 km because they remain in orbit too long. In order to enable CubeSat deployments at higher release altitudes, a low-cost, ultra-reliable deorbit device is needed.

This thesis reports on efforts to develop a deployable and passively inflatable drag brake that can deorbit from higher orbital altitudes, thereby complying with the 25-year …

Development Of The Compact Jet Engine Simulator From Concept To Useful Test Rig, Henry H. Haskin

Mechanical & Aerospace Engineering Theses & Dissertations

NASA had a goal to develop a set of modeling tools for designing next generation civil transport aircraft with reduced noise, emissions and increased fuel efficiency by 2016. To verify the models, a database of aerodynamic and acoustic data was needed for an unconventional flying wing design that was predicted to meet the goals. A Compact Jet Engine Simulator (CJES) was needed as the jet source for the 5.8% scale model. Ultra-Compact Combustor Technology from the Air Force Research Laboratory was used to reduce the conventional burner acoustic test rigs down to the required scale size. The Air Force design …

An Investigation Into The Potential Benefits Of Distributed Electric Propulsion On Small Uavs At Low Reynolds Numbers, Engin Baris

Mechanical & Aerospace Engineering Theses & Dissertations

Distributed electric propulsion systems benefit from the inherent scale independence of electric propulsion. This property allows the designer to place multiple small electric motors along the wing of an aircraft instead of using a single or several internal combustion motors with gear boxes or other power train components. Aircraft operating at low Reynolds numbers are ideal candidates for benefiting from increased local flow velocities as provided by distributed propulsion systems.

In this study, a distributed electric propulsion system made up of eight motor/propellers was integrated into the leading edge of a small fixed wing-body model to investigate the expected improvements …

Development Of An Analysis And Design Optimization Framework For Marine Propellers, Ashish C. Tamhane

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a framework for the analysis and design optimization of ship propellers is developed. This framework can be utilized as an efficient synthesis tool in order to determine the main geometric characteristics of the propeller but also to provide the designer with the capability to optimize the shape of the blade sections based on their specific criteria.

A hybrid lifting-line method with lifting-surface corrections to account for the three-dimensional flow effects has been developed. The prediction of the correction factors is achieved using Artificial Neural Networks and Support Vector Regression. This approach results in increased approximation accuracy compared …

A Comparison Of Microstructure And Uniaxial Compressive Response Of Ice-Templated Porous Alumina Scaffolds Fabricated From Two Different Particle Sizes, Nikhil D. Dhavale

Mechanical & Aerospace Engineering Theses & Dissertations

Development of bio-inspired highly porous (>50 vol.%) cellular ceramics is crucial to meet the demand of high-performance lightweight and damage-tolerant materials for a number of cutting-edge applications including impact energy absorption, biomedical implants, and energy storage. A key design feature that is observed in many natural materials (e.g., nacre, bamboo, wood, etc.) is the presence of hierarchical microstructure that results in an excellent synergy of various material properties, which are otherwise considered as mutually exclusive in current paradigm of materials design. To this end, development of multilayered, interconnected and anisotropic cellular ceramics could benefit the aforementioned applications. However, mimicking …

Design Of Experiments Enhanced Statistical Process Control For Wind Tunnel Check Standard Testing, Ben D. Phillips

Mechanical & Aerospace Engineering Theses & Dissertations

The current wind tunnel check standard testing program at NASA Langley Research Center is focused on increasing data quality, uncertainty quantification and overall control and improvement of wind tunnel measurement processes. The statistical process control (SPC) methodology employed in the check standard testing program allows for the tracking of variations in measurements over time as well as an overall assessment of facility health. While the SPC approach can and does provide researchers with valuable information, it has certain limitations in the areas of process improvement and uncertainty quantification. It is thought by utilizing design of experiments methodology in conjunction with …

Detecting And Resolving Air Traffic Conflicts Using A Point Of Closest Approach Method, Marc S. Easton

Mechanical & Aerospace Engineering Theses & Dissertations

A geometrical point of closest approach method is used to solve air traffic conflict detection/resolution problems with a single conflict vehicle that is unaware or unable to aid in resolving the conflict. Nonlinear, three degree of freedom equations of motion for a point-mass vehicle are derived and formulated to allow commanded trajectories to steer the vehicle to a desired location. A dynamic model is developed to propagate the vehicle in three dimensions. A closed-loop model implementing a negative feedback controller using a Proportional-Integral-Derivative control scheme is used to drive the vehicle to match the commanded trajectories. A conflict detection/resolution algorithm …

Development Of The Compact Jet Engine Simulator From Concept To Useful Test Rig, Henry H. Haskin

Mechanical & Aerospace Engineering Theses & Dissertations

Two Compact Jet Engine Simulator (CJES) units were designed for integrated wind tunnel acoustic experiments involving a Hybrid Wing Body (HWB) vehicle. To meet the 5.8% scale of the HWB model, Ultra Compact Combustor technology from the Air Force Research Laboratory was used. The CJES units were built and integrated with a control system in the NASA Langley Low Speed Aero acoustic Wind Tunnel. The combustor liners, plug—vane and flow conditioner components were built in-house at Langley Research Center. The operation of the CJES units was mapped and fixes found for combustor instability tones and rig flow noise. The original …

Carbon Deposition During Oxygen Production Using High Temperature Electrolysis And Mitigation Methods, Timothy Adam Bernadowski

Mechanical & Aerospace Engineering Theses & Dissertations

Carbon dioxide in the Martian atmosphere can be converted to oxygen during high temperature electrolysis for use in life-support and fuel systems on manned missions to the red planet. During electrolysis of carbon dioxide to produce oxygen, carbon can deposit on the electrolysis cell resulting in lower efficiency and possibly cell damage. This would be detrimental, especially when the oxygen product is used as the key element of a space life support system. In this thesis, a theoretical model was developed to predict hazardous carbon deposition conditions under various operating conditions within the Martian atmosphere. The model can be used …

Development And Implementation Of A Propeller Test Capability For Gl-10 "Greased Lightning" Propeller Design, Brian Edward Duvall

Mechanical & Aerospace Engineering Theses & Dissertations

Interest in small unmanned aerial vehicles has increased dramatically in recent years. Hybrid vehicles which allow forward flight as a fixed wing aircraft and a true vertical landing capability have always had applications. Management of the available energy and noise associated with electric propeller propulsion systems presents many challenges. NASA Langley has developed the Greased Lightning 10 (GL-10) vertical takeoff, unmanned aerial vehicle with ten individual motors and propellers. All are used for propulsion during takeoff and contribute to acoustic noise pollution which is an identified nuisance to the surrounding users. A propeller test capability was developed to gain an …

Experimental Investigation Of Turbulent Structures And Non-Equilibrium Effects In Axial Wake Vortices Via Particle Image Velocimetry, Jeffry William Ely

Mechanical & Aerospace Engineering Theses & Dissertations

Vortices are a common phenomenon in fluid flows that arise as kinetic energy dissipates into heat via viscous interaction. They arise naturally at large scales in the form of dust devils, tornadoes, and as a counter-rotating vortex pair in the wake of aircraft. It is important to understand the conditions leading to their formation, their duration, and their dissipation in order to forecast or prevent undesirable effects. Among these deleterious effects is a decrease in safety of aircraft operations in the wake of other aircraft, an extremely common situation at airports around the world. A large number of mathematical models …

Modeling Shock Waves Using Exponential Interpolation Functions With The Least-Squares Finite Element Method, Bradford Scott Smith Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

The hypothesis of this research is that exponential interpolation functions will approximate fluid properties at shock waves with less error than polynomial interpolation functions. Exponential interpolation functions are derived for the purpose of modeling sharp gradients. General equations for conservation of mass, momentum, and energy for an inviscid flow of a perfect gas are converted to finite element equations using the least-squares method. Boundary conditions and a mesh adaptation scheme are also presented. An oblique shock reflection problem is used as a benchmark to determine whether or not exponential interpolation provides any advantages over Lagrange polynomial interpolation. Using exponential interpolation …

Long-Term Quantitative Study Of Wind-Tunnel Balance Calibrations Across Multiple Calibration Systems, Ryan James Callahan

Mechanical & Aerospace Engineering Theses & Dissertations

Internal strain-gauge balances are multi-dimensional force transducers widely employed in wind tunnels to obtain accurate aerodynamic force and moment data on an aircraft model. Balances are calibrated periodically to assure measurement accuracy. The calibration provides a mathematical model relating the forces applied to the balance and the output signal from the balance. Currently, there are multiple types of internal strain-gauge balances used in wind-tunnel testing as well as multiple methods by which balances are calibrated. Because of the differences in the hardware and methodologies used to calibrate a wind-tunnel balance, it is hard to quantify the differences seen between the …

Experimental Analysis Of Turbulent Structures And The Effects Of Non-Equilibrium On An Axial Vortex, Michael P. Thompson

Mechanical & Aerospace Engineering Theses & Dissertations

Examples of the axial vortex include, dust devils, trailing line aircraft wake vortices, and tornadoes. Some of these vortices can prove hazardous to individuals and property. This necessitates that studies be conducted to understand their structure and to attempt to develop mathematical models of the flow physics involved. A wide variety of experimental techniques have been used in the past to study the vortex, with flow visualization and hotwire anemometry being chosen for this experiment. There have been many inadequate mathematical models proposed in the past. The experimental results obtained were compared to the work of Ash, Zardadkhan and Zuckerwar …

A Hybrid Position Feedback Controller For Bistable Structures, Mehmet R. Simsek

Mechanical & Aerospace Engineering Theses & Dissertations

Bistability is the property of structures showing the ability to attain two statically stable states. Due to dynamic and static advantages such as no energy demand at stable positions and providing higher deflections compared to a monostable structure, bistability may be appealing in control surface design for aircraft structures and load alleviation for wind turbine blades. The dynamics of bistable structures is nonlinear because of the snap-through occurring during the cross-well oscillation between two stable states. A new control strategy called hybrid position feedback control is developed based on the conventional positive position control to exploit linear dynamics of bistable …

Nonlinear Flight Control Design Using Backstepping Methodology, Thanh Trung Tran

Mechanical & Aerospace Engineering Theses & Dissertations

The subject of nonlinear flight control design using backstepping control methodology is investigated in the dissertation research presented here. Control design methods based on nonlinear models of the dynamic system provide higher utility and versatility because the design model more closely matches the physical system behavior. Obtaining requisite model fidelity is only half of the overall design process, however. Design of the nonlinear control loops can lessen the effects of nonlinearity, or even exploit nonlinearity, to achieve higher levels of closed-loop stability, performance, and robustness. The goal of the research is to improve control quality for a general class of …

Thrust Prediction For A Rotor Operating In A Ship Airwake, Mathew Thomas

Mechanical & Aerospace Engineering Theses & Dissertations

This report details work performed at Old Dominion University focused on developing a thrust prediction capability for a rotor operating in a ship airwake. The study has built upon previous experimental work utilizing particle image velocimetry-based velocity field measurements to quantify the degree of coupling in a simplified rotor/ship airwake experiment. Using the velocity field data of the previous study, a database was built representing the volume over the landing deck. Rotor thrust was computed using blade element methods and compared to direct load cell measurements and to a superposed velocity field. Results show that the blade element method has …

Flight Dynamics Nonlinearity Assessment Across A New Aerodynamic Attitude Flight Envelope, Ayman Muhammad Abdallah

Mechanical & Aerospace Engineering Theses & Dissertations

A new asymmetric level aerodynamic attitude flight envelope is introduced in this dissertation. The aerodynamic attitude envelope is an angle of attack vs. sideslip angle region which describes the extent of where an aircraft can sustain a steady slipping horizontal flight condition. The new envelope is thus an extension of the more common speed-altitude symmetric level flight envelope. This new envelope can be used for design requirements, dynamic analysis, control synthesis, or performance comparison. Moreover, this envelope provides enhanced insight into trimability-controllability limitations within the aircraft design model. The aerodynamic attitude flight envelope is constructed for a six degree of …

Nano Scale Mechanical Analysis Of Biomaterials Using Atomic Force Microscopy, Diganta Dutta

Mechanical & Aerospace Engineering Theses & Dissertations

The atomic force microscope (AFM) is a probe-based microscope that uses nanoscale and structural imaging where high resolution is desired. AFM has also been used in mechanical, electrical, and thermal engineering applications. This unique technique provides vital local material properties like the modulus of elasticity, hardness, surface potential, Hamaker constant, and the surface charge density from force versus displacement curve. Therefore, AFM was used to measure both the diameter and mechanical properties of the collagen nanostraws in human costal cartilage. Human costal cartilage forms a bridge between the sternum and bony ribs. The chest wall of some humans is deformed …