Aerospace Engineering Commons^™

Empirical Modeling Of Tilt-Rotor Aerodynamic Performance, Michael C. Stratton

Mechanical & Aerospace Engineering Theses & Dissertations

There has been increasing interest into the performance of electric vertical takeoff and landing (eVTOL) aircraft. The propellers used for the eVTOL propulsion systems experience a broad range of aerodynamic conditions, not typically experienced by propellers in forward flight, that includes large incidence angles relative to the oncoming airflow. Formal experiment design and analysis techniques featuring response surface methods were applied to a subscale, tilt-rotor wind tunnel test for three, four, five, and six blade, 16-inch diameter, propeller configurations in support of development of the NASA LA-8 aircraft. Investigation of low-speed performance included a maximum speed of 12 m/s and …

Analysis Of A Non-Equilibrium Vortex Pair As Aircraft Trailing Vortices, Manuel Ayala

Mechanical & Aerospace Engineering Theses & Dissertations

Shortly after the roll-up evolution of the vortex sheet behind the wings of an aircraft, a coherent counter-rotating vortex pair emerges. Presence of this vortex pair in the downstream of an aircraft, creates unsafe conditions for other aircraft, especially near airport runways. Fundamental knowledge of the physics that govern the formation, duration and dissipation of aircraft wake vortices is desirable in order to improve aircraft operational safety. This study uses non-equilibrium pressure theory to develop an accurate model describing the physical behavior of the vortex pair created by an aircraft in the early to mid-field vortex regime. An isolated aircraft …

The Effect Of Through Thickness Reinforcement On Debonding Behavior Of Skin/Stringer Configuration, Yogaraja Sridhar

Mechanical & Aerospace Engineering Theses & Dissertations

Investigation of this study is to the determine the crack propagation and disbonding in the bonded region of the skin and stringer specimen. An adhesive layer has been used to bond the skin and stringer by using a heat press operation. After the bonding, a drilling method has been adopted to install the through thickness reinforcement in the specimen. The key role of the through thickness reinforcement is to increase the stiffness and strength of the panels and to prevent the crack propagation or disbonding of the panels. The reinforcement was installed in pure (Pristine) samples and in defect samples …

A Digital One Degree Of Freedom Model Of An Electromagnetic Position Sensor, Michelle Elizabeth Weinmann

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this project was to improve an existing system currently in use by NASA Langley Research Center (LaRC). The 6-inch Magnetic Suspension and Balance System (MSBS) built at MIT is operational with control in three degrees of freedom, with two additional degrees of freedom exhibiting passive stability. The means for measuring model displacement within the magnetic environment is an Electromagnetic Position Sensor (EPS), consisting of excitation coils at 20 kHz and multiple sets of pickup coils. The pickup coil voltages are proportional to model displacement in each degree of freedom. However, the EPS electronic signal processing system is …

Development And Applications Of Adjoint-Based Aerodynamic And Aeroacoustic Multidisciplinary Optimization For Rotorcraft, Ramiz Omur Icke

Mechanical & Aerospace Engineering Theses & Dissertations

Urban Air Mobility (UAM) is one of the most popular proposed solutions for alleviating traffic problems in populated areas. In this context, the proposed types of vehicles mainly consist of rotors and propellers powered by electric motors. However, those rotary-wing components can contribute excessively to noise generation. Therefore, a significant noise concern emerges due to urban air vehicles in or around residential areas. Reducing noise emitted by air vehicles is critically important to improve public acceptance of such vehicles for operations in densely populated areas.

Two main objectives of the present dissertation are: (1) to expand the multidisciplinary optimization to …

A New Method For Estimating The Physical Characteristics Of Martian Dust Devils, Shelly Cahoon Mann

Mechanical & Aerospace Engineering Theses & Dissertations

Critical to the future exploration of Mars is having a detailed understanding of the atmospheric environment and its potential dangers. The dust devil is one of these potential dangers. The transport of dust through saltation is believed to be the driving mechanism responsible for Martian weather patterns. The two primary mechanisms for dust transport are dust storms and dust devils. Dust devils on Mars are a frequent occurrence with one in five so called giant dust devils being large enough to leave scars on the surface that are visible from space. Due to the thin atmosphere, winds of 60 mph …

A Model-Based Systems Engineering Approach To E-Vtol Aircraft And Airspace Infrastructure Design For Urban Air Mobility, Heidi Selina Glaudel

Mechanical & Aerospace Engineering Theses & Dissertations

This paper serves to contribute to Model-Based Systems Engineering (MBSE) by following the NASA Systems Engineering Handbook framework for a Systems Engineering (SE) design approach to an Electric Vertical Takeoff and Landing (e-VTOL) aircraft and the incorporating airspace infrastructure. The focus of this study is, by using the MBSE model created, to capture the technical requirements definition and design intent of the vehicle and airspace inclusive of community specific knowledge derived from the Federal Aviation Administration (FAA) NextGen Urban Air Mobility (UAM) Concept of Operations (ConOps) version 1.0. The stakeholder requirements derived from the FAA UAM NextGen ConOps will form …

Improved Strain Gage Instrumentation Strategies For Rotorcraft Blade Measurements, Timothy S. Davis

Mechanical & Aerospace Engineering Theses & Dissertations

In this work, a new strategy is presented to wire, calibrate, and measure strain gages for rotor blade testing that will provide more information and is robust to individual gage loss. The additional information can be used in several ways. including reducing redundancy, offering rapid identification of damage locations, and in some cases reducing risk allowing tests to continue to collect calibrated data after one or more sensors have failed. This strategy replaces the classical four-gage full Wheatstone bridge with four separately wired quarter bridges that are combined into a full bridge in the data acquisition system using a calculated …

Conical Orbital Mechanics: A Rework Of Classic Orbit Transfer Mechanics, Cian Anthony Branco

Mechanical & Aerospace Engineering Theses & Dissertations

Simple orbital maneuvers obeying Kepler’s Laws, when taken with respect to Newton’s framework, require considerable time and effort to interpret and understand. Instead of a purely mathematical approach relying on the governing relations, a graphical geometric conceptual representation provides a useful alternative to the physical realities of orbits. Conic sections utilized within the full scope of a modified cone (frustum) were employed to demonstrate and develop a geometric approach to elliptical orbit transformations. The geometric model in-question utilizes the rotation of a plane intersecting the orbital frustum at some angle β (and the change in this angle) in a novel …

The Effect Of Compaction Temperature And Pressure On Mechanical Properties Of 3d Printed Short Glass Fiber Composites, Pushpashree Jain Ajith Kumar Jain

Mechanical & Aerospace Engineering Theses & Dissertations

Among many thermoplastics that are used in engineering, polyamide 6 (nylon 6) is an extremely versatile engineering thermoplastic. Nylon filled with glass fibers has higher mechanical strength and high wear resistance than general purpose nylon. 3D printed composites, based on fused filament modeling, typically suffer from poor bead-to-bead bonding and relatively high void content, limiting their mechanical properties

This thesis explores the effect of compaction pressure and temperature on improving the mechanical properties of 3D printed composites. Engineering moduli in the printing and transverse to printing direction, as well as ultimate strength were measured using the tensile testing with Digital …

Space-Based Countermeasure For Hypersonic Glide Vehicle, Robert Joseph Fowler Iv

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this thesis is to investigate the effectiveness of a space-based laser weapon system for countering a hypersonic glide vehicle. Hypersonic glide vehicles are an emerging type of weapon system which combine the range of ballistic missiles with the maneuverability of cruise missiles. These systems pose a unique threat to military assets not only for their expanded capabilities but also for the lack of an effective defensive countermeasure. Space-based laser weapon systems may offer a solution to this problem. The dynamics of a space-based laser system defending against a hypersonic glide vehicle are modeled first. The governing equations …

Onboard Autonomous Controllability Assessment For Fixed Wing Suavs, Brian Edward Duvall

Mechanical & Aerospace Engineering Theses & Dissertations

Traditionally fixed-wing small Unmanned Arial Vehicles (sUAV) are flown while in direct line of sight with commands from a remote operator. However, this is changing with the increased popularity and ready availability of low-cost flight controllers. Flight controllers provide fixed-wing sUAVs with functions that either minimize or eliminate the need for a remote operator. Since the remote operator is no longer controlling the sUAV, it is impossible to determine if the fixed-wing sUAV has proper control authority. In this work, a controllability detection system was designed, built, and flight-tested using COTS hardware. The method features in-situ measurement and analysis of …

Model Based Systems Engineering For A Venture Class Launch Facility, Walter Mcgee Taraila

Mechanical & Aerospace Engineering Theses & Dissertations

A study of Model-Based Systems Engineering (MBSE) applied to a small-lift launch facility is presented. The research uses Systems Modeling Language (SysML) products and functional diagrams to document the structure, controls, electrical power, hydraulic, safety mechanisms, software, and fluid ground systems on a launch pad. The research is motivated by the need to design complex systems with an unambiguous understanding that improves communication, quality, productivity, and reduces risk. A model is developed following the ISO/IEC-15288 technical process framework. The stakeholder requirements are defined and analyzed to provide traceability to individual systems and subsystems. An architectural design is realized and implemented …

Finite Element Analysis Investigation Of Hybrid Thin-Ply Composites For Improved Performance Of Aerospace Structures, Alana M. Zahn

Mechanical & Aerospace Engineering Theses & Dissertations

Commercial and private aircraft have a need for strong yet light materials in order to have the most ideal performance possible. This study looks at the use of thin-ply composite materials to improve the performance of aircraft structures by means of weight savings and/or strength increase when compared to laminates that are composed of exclusively standard-ply materials. In order to perform an investigation based solely on finite element analysis, validation efforts were performed using test data from open hole tension, open hole compression, notched tension, and notched compression specimens. Once the models were validated sufficiently, the same modeling practices were …

Mechanism Of Compaction With Wrinkle Formation During Automatic Stitching Of Dry Fabrics And The Size Effect Of Compression Molded Discontinuous Fiber-Reinforced Composites, Anibal Benjamin Beltran Laredo

Mechanical & Aerospace Engineering Theses & Dissertations

With an ever-increasing demand for composites, more ways of manufacturing them are becoming popular and widely used. Stitching of dry fabrics is an efficient method for improving delamination resistance. Discontinuous fiber reinforced composites can be used as a lightweight alternative material for metals through a process of compression molding, which allows for complex shape manufacturing while offering structural grade mechanical properties.

This study demonstrates how the stitching of dry fabrics can be adapted to more complex surfaces. The consequences of stitching of curvilinear surfaces can result in defect formation. Therefore, to understand the physical formation of possible defects, experimental characterization …

Cfd Simulations Of A Propeller-Wing Interaction, Asim Oktay Akdeniz

Mechanical & Aerospace Engineering Theses & Dissertations

In this study, 3-D turbulent flows around a propeller driven aircraft model placed in a subsonic wind tunnel were computationally simulated for qualitative investigation of near field wakes. The geometry of the model was created using commercial mesh generation software, GRIDGEN, and then simulations were performed using a commercial finite volume Reynolds-Averaged Navier-Stokes (RANS) solver FLUENT.

Initial runs were performed to validate the boundary conditions and setup of the problem where a hybrid mesh consisting of multi-blocks was in use. Sliding mesh concept used in the computations. Laminar flow simulation have been utilized and tested besides Spalart-Allmaras and k-ω SST …

A Study Of The Aeroacoustics Of Swept Propellers For Small Unmanned Aerial Vehicles, Arthur David Wiedemann

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, small unmanned aerial vehicles (UAVs) have increased in availability and use in both public and commercial sectors. This increased use of small UAVs or “drones” has the unfortunate consequence of introducing excessive noise into communities where they operate. Implementation of noise reduction methods is necessary if we wish to see expanded use of drones in public areas. With electric propulsion, the primary source of noise is the rotor/propeller used in contemporary multi-rotor configurations. In this thesis, the aerodynamics and acoustic behavior of various swept propellers is examined with computational and experimental methods.

A family of propeller geometries …

Through-Thickness Reinforcement And Repair Of Carbon Fiber Based Honeycomb Structures Under Flexure And Tension Of Adhesively Bonded Joints, Aleric Alden Sanders

Mechanical & Aerospace Engineering Theses & Dissertations

Repair and reinforcement of composite honeycomb structures is an area of concern as higher demands are being placed on high strength, lightweight structural materials, such as carbon fiber reinforced plastics and corresponding honeycomb structures. A common issue with these structures is when a delamination in the facesheet may form and spread, leading to a failure scenario. An investigation of adding a through thickness reinforcement (TTR) to these structures at the sample level that undergo four-point-bending, tension, and joining methods is conducted throughout this thesis. The embedding of pultruded carbon fiber rods is found to be an ideal addition to composite …

A Post-Impact Behavior Of Platelet-Based Composites Produced By Compression Molding, Christopher Eugene Ervin Volle

Mechanical & Aerospace Engineering Theses & Dissertations

Prepreg-based Platelet Molded Compounds (PPMCs) are quickly becoming a widely used method for creating structural components in the aerospace and automotive industries. The discontinuous nature of the platelets used allow good formability of both complex and basic structural components; from seats on commercial airplanes to outer panels of vehicles.

This thesis will look at an important research question of these composites: how PPMCs behave under dynamic loading, e.g. impact and post-impact behavior. Impact is analyzed using recorded force and velocity data to find the absorbed energy. Digital image correlation is used with compression after impact testing to study the propagation …

Trajectory Simulation With Battery Modeling For Electric Powered Unmanned Aerial Vehicles, Ege Konuk

Mechanical & Aerospace Engineering Theses & Dissertations

Fixed wing electric powered unmanned aerial vehicles (UAVs) has been widely adopted for the last decade in a great number of applications. One of the primary advantages to fixed wing versus multi-rotor designs is the efficiency in forward flight with best possible range and endurance capabilities. In electrically powered air vehicles range and endurance are monitored by the State-of-Charge (SOC) of the battery. To understand the capabilities of the battery, discharge experiments can be conducted in lab environments; however, sometimes the results are difficult to integrate in flight simulations.

In this thesis, a trajectory simulation is developed that can estimate …

Thermal Contact Resistance Measurement And Related Uncertainties, Amanda Elizabeth Stark

Mechanical & Aerospace Engineering Theses & Dissertations

Thermal contact resistance is an important parameter in detailed thermal analysis and design of aerospace systems. The ability to determine thermal contact resistance reliably can have a significant impact on the fidelity of thermal models—particularly for space applications. The 2004 NASA Langley Research Center thermal contact resistance test apparatus has been employed to evaluate two methods for inferring estimated interface surface temperatures so that thermal contact resistance can be calculated more accurately. The traditional method of extrapolation is a steady-state approach, while the new method utilizes inverse heat transfer techniques to account for inherent unsteadiness in these quasi-steady-state measurements. The …

Rotorcraft Blade Angle Calibration Methods, Brian David Calvert Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

The most vital system of a rotorcraft is the rotor system due to its effects on the overall flight quality of the vehicle. Therefore, it is of importance to be able to accurately determine blade position during flight so that fine adjustments can be made to ensure a safe and efficient flight. In this study, a current calibration method focusing on the pitch, flap, and lead-lag blade angles is analyzed and found to have larger than acceptable error associated with the sensor calibrations. A literature review is conducted which reveals four novel methods that can potentially increase the accuracy of …

Nonlinearity Index Aircraft Spin Motion Analysis With Dynamic Inversion Spin Recovery Controller Design, Jeffry Walker

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this thesis research is to extend the previous work of Tapolcai utilizing nonlinearity index theory to quantitatively analyze nonlinearities in an aircraft model and to augment these undesirable nonlinear characteristics with feedback control. In his work Tapolcai utilized a simplified rotational three degree of freedom model to analyze spin conditions of the F-18 High Angle-of-Attack Research Vehicle model. Through the application of nonlinearity index theory, regions of severe nonlinearity were uncovered exhibiting chaotic non-periodic behavior, periodic limit cycling, and instability. If these conditions were encountered during flight, the aircraft would exhibit undesirable response characteristics thereby requiring augmented …

Extension Of A Penalty Method For Numerically Solving Constrained Multibody Dynamic Problems, Troy Newhart

Mechanical & Aerospace Engineering Theses & Dissertations

Numerical analysis of constrained static and multibody dynamic systems has become an integral part of engineering analysis with the continued improvements in technology and software availability. Many methods currently exist for numerically solving constrained static and dynamic systems. The applicability of a penalty method for constrained static solutions is observed in many academic texts and papers. The appeal for using a penalty method in statics pertains to its ease of implementation, computational suitability, and accuracy. This thesis extends a static penalty method for use with constrained multibody dynamics to observe if the penalty method’s benefits are similar for a dynamics …

Reducing The Noise Impact Of Unmanned Aerial Vehicles By Flight Control System Augmentation, Matthew B. Galles

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this thesis is to explore methods to reduce the noise impact of unmanned aerial vehicles operating within acoustically sensitive environments by flight control system augmentation. Two methods are investigated and include: (i) reduction of sound generated by vehicle speed control while flying along a nominal path and (ii) reduction of acoustic exposure by vehicle path control while flying at a nominal speed. Both methods require incorporation of an acoustic model into the flight control system as an additional control objective and an acoustic metric to characterize primary noise sources dependent on vehicle state. An acoustic model was …

Periodic Orbit Analytic Construction In The Circular Restricted Three-Body Problem, Jay Shriram Suryawanshi

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis investigates an approximate analytic construction of halo-type periodic orbits about the collinear equilibrium points in the circular restricted three-body problem. The research follows a parallel approach to the one used by Ghazy and Newman, but the initial assumptions and utilized functions are unique to this thesis. A suppositional base solution constructed using Jacobi elliptic functions and satisfying Jacobi's integral equation is at the core of the analytic construction framework. The locus of this solution is a circle lying in the plane perpendicular to the line joining the primaries. The base solution elicits a closed-form expression for the period …

Characterization And Optimization Of A Propeller Test Stand, Colin Bruce Leighton Benjamin

Mechanical & Aerospace Engineering Theses & Dissertations

In recent history, there has been a rapid rise in the use of drones, and they are expanding in popularity each year. The widespread use and future capabilities of these unmanned aerial vehicles (UAVs) will call for increased study and classification of propellers to maximize their performance. As a result, it is necessary to have continuity in the development, maximization, and optimization of propeller test stand’s capability to collect accurate and precise measurements. It is of significant advantage to have the capability of accurately characterizing a propeller based on its thrust and torque. In this study, a propeller test stand …

Design And Manufacture Of An Inertial Cascade Impactor For Industrial Hygiene Purposes, Hector Joel Gortaire

Mechanical & Aerospace Engineering Theses & Dissertations

Inertial cascade impactors are devices commonly used for industrial hygiene and pharmaceutical studies. Their main purpose is to separate particulate matter suspended in aerosols according to their sizes, which can vary from over 10 µm to 0.5 µm. Their versatility and ease of operation make them suitable for on-site sampling; however, designing them requires a careful consideration of the different geometric parameters that characterize them.

In this thesis, a 5-stage inertial cascade impactor was designed, modelled, constructed, and tested. The main design parameter was the volumetric flow rate, 40 l/min, which was provided by a vacuum pump. By continuous iterations, …

Comparison Of Support Methods For Static Aerodynamic Testing And Validation Of A Magnetic Suspension And Balance System, Cameron K. Neill

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic suspension wind tunnels offer an alternative to traditional physical support methods. They allow for the collection of support interference free data and broader dynamic test capabilities than existing methods. Determination of dynamic aerodynamic characteristics is a crucial portion of the design of new re-entry capsules. A NASA initiative restored the 6-inch Magnetic Suspension and Balance System to support the design of a new MSBS for a supersonic wind tunnel. Before a new MSBS can be constructed, the characteristics of the current MSBS must be examined.

This thesis discusses the calibration and validation of the 6-inch MSBS. After calibration, three …

Effects Of Automated Fiber Placement On High Strain Rate Compressive Response Of Advanced Composites, Alexander Trochez

Mechanical & Aerospace Engineering Theses & Dissertations

Automated Fiber Placement (AFP) technology shows great promise in manufacturing carbon fiber composite structures. However, intermittent defects occur in the process that can affect the overall mechanical performance of the structure. The aim of this work is to investigate the effects of deliberately placed principal defects (Gap, Overlap, and Fold) on the compressive response under quasistatic (strain rate ~10^-3 s^-1) and dynamic (strain rate ~10³ s-1) loading conditions. The controlled defects were placed at the laminate level in different orientations and depths. High strain rate compression experiments were conducted using a split Hopkinson pressure bar (SHPB) …