Aerospace Engineering Commons^™

Discussion And Analysis Of Missile Igc Design, Michael W. Dancer, S. N. Balakrishnan, Ernest J. Ohlmeyer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Missile intercept systems used in the next generation missile defense system will require extremely accurate performance of all component systems. Such systems will need to guarantee successful intercept of highly maneuvering targets. as a result, such interceptor systems require much greater performance in its guidance, control, and estimation subsystems. in order to develop systems that meet the required accuracies, integrated guidance and control (IGC) systems are currently being studied. These IGC architectures infuse the guidance and control systems into a single framework thereby promoting natural synergy among the missile subsystems. Previous work in this area has relied on missile body-Based …

Analysis Of Access-To-Space Missions Utilizing On-Board Energy Management And Entropic Analysis, Tyler Winter

Masters Theses

"The overall objective of this study is the thermodynamically consistent quantification of second-law and performance losses for vehicle configurations implemented or suggested for access-to-space missions and the development of the relationships between the mission entropy generation and overall mission performance. The detailed theory which allows thermodynamically rigorous loss accounting (entropy generation and direct relationship to vehicle performance) is developed and discussed for aerospace vehicles. A full vehicle trajectory code utilizing simplified models for multi-stage rockets and air-breathing propulsion systems is developed and validated specifically for use as a testbed for second law-based theory and concepts. Results are shown in which …

Efficient Uncertainty Quantification Applied To The Aeroelastic Analysis Of A Transonic Wing, Serhat Hosder, Robert W. Walters, Michael Balch

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The application of a Point-Collocation Non-Intrusive Polynomial Chaos method to the uncertainty quantification of a stochastic transonic aeroelastic wing problem has been demonstrated. The variation in the transient response of the first aeroelastic mode of a three-dimensional wing in transonic flow due to the uncertainty in free-stream Mach number and angle of attack was studied. A curve-fitting procedure was used to obtain time-independent parameterization of the transient aeroelastic responses. Among the uncertain parameters that characterize the time-dependent transients, the damping factor was chosen for uncertainty quantification, since this parameter can be thought as an indicator for flutter. Along with the …

Manufacturing Of Transparent Composites Using Vacuum Infusion Process, Jason Niles Gallagher

Masters Theses

"Glass is the most commonly used transparent material. However, glass is not suitable where low weight and high strength are required. For many applications there exists a need for mechanically strong composite materials of high optical quality and transparency equivalent to window glass. Glass fiber reinforced transparent composite is a viable solution. Transparency is maintained by precisely matching the refractive index of the matrix with that of the glass fiber. Aircraft canopies and transparent armor can be potential applications for this new class of materials.

In the present work, transparent composites are manufactured using vacuum infusion process. Both rectangular glass …

Optimal Control Of Class Of Non-Linear Plants Using Artificial Immune Systems: Application Of The Clonal Selection Algorithm, S. A. Panimadai Ramaswamy, Ganesh K. Venayagamoorthy, S. N. Balakrishnan

Electrical and Computer Engineering Faculty Research & Creative Works

The function of natural immune system is to protect the living organisms against invaders/pathogens. Artificial Immune System (AIS) is a computational intelligence paradigm inspired by the natural immune system. Diverse engineering problems have been solved in the recent past using AIS. Clonal selection is one of the few algorithms that belong to the family of AIS techniques. Clonal selection algorithm is the computational implementation of the clonal selection principle. The process of affinity maturation of the immune system is explicitly incorporated in this algorithm. This paper presents the application of AIS for the optimal control of a class of non-linear …

Analysis Of One-Dimensional And Two-Dimensional Thin Film "Pull-In" Phenomena Under The Influence Of An Electrostatic Potential, Gang Duan, Kai-Tak Wan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A thin one-dimensional rectangular or two-dimensional axisymmetric film is clamped at the perimeter. an electrostatic potential (V*₀) applied to a pad directly underneath the film leads to a "pull-in" phenomenon. the electromagnetic energy stored in the capacitive film-pad dielectric gap is decoupled from the mechanical deformation of the film using the Dugdale-Barenblatt-Maugis cohesive zone approximation. the ratio of film-pad gap (g) to film thickness (h), or γ=g/h, is found to play a crucial role in the electromechanical behavior of the film. Solution spanning a wide range of y is found such that V*₀ ∝ γ^_3/2 for …

Response To "Comment On 'Adhesion-Delamination Mechanics Of A Presented Rectangular Film Adhered Onto A Rigid Substrate' [J. Appl. Phys. 101, 024903 (2007)]", Kai-Tak Wan, Gang Duan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Reinforcement Learning Based Output-Feedback Control Of Nonlinear Nonstrict Feedback Discrete-Time Systems With Application To Engines, Peter Shih, Jonathan B. Vance, Brian C. Kaul, Jagannathan Sarangapani, J. A. Drallmeier

Electrical and Computer Engineering Faculty Research & Creative Works

A novel reinforcement-learning based output-adaptive neural network (NN) controller, also referred as the adaptive-critic NN controller, is developed to track a desired trajectory for a class of complex nonlinear discrete-time systems in the presence of bounded and unknown disturbances. The controller includes an observer for estimating states and the outputs, critic, and two action NNs for generating virtual, and actual control inputs. The critic approximates certain strategic utility function and the action NNs are used to minimize both the strategic utility function and their outputs. All NN weights adapt online towards minimization of a performance index, utilizing gradient-descent based rule. …

Cooperative Uav Formation Flying With Obstacle/Collision Avoidance, Xiaohua Wang, Vivek Yadav, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Navigation problems of unmanned air vehicles (UAVs) flying in a formation in a free and an obstacle-laden environment are investigated in this brief. when static obstacles popup during the flight, the UAVs are required to steer around them and also avoid collisions between each other. In order to achieve these goals, a new dual-mode control strategy is proposed: a “safe mode” is defined as an operation in an obstacle-free environment and a “danger mode” is activated when there is a chance of collision or when there are obstacles in the path. Safe mode achieves global optimization because the dynamics of …

A Novel Cylindrical Punch Method To Characterize Interfacial Adhesion And Residual Stress Of A Thin Polymer Film, Bing Feng Ju, Kuo Kang Liu, Ming Fung Wong, Kai Tak Wan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Adhesion of a pre-stressed silicone rubber film to a planar graphite surface was investigated by a new cylindrical punch method. a homemade apparatus was constructed to meet force and displacement resolutions of 0.1 μN and 10 nm. When the punch approached the intersurface force range across the punch-film gap, the film jumped into contact at "pull-in". Upon unloading, once the tensile load reached a threshold, a spontaneous delamination occurred at "pull-off" with a non-zero contact circle. a theoretical model was constructed based a simple energy balance. the new method can be used to characterize an adhesion interface between a pre-stressed …

Management Of An Intelligent Argumentation Network For A Web-Based Collaborative Engineering Design Environment, Xiaoqing Frank Liu, Man Zheng, Ganesh K. Venayagamoorthy, Ming-Chuan Leu

Computer Science Faculty Research & Creative Works

Conflict resolution is one of the most challenging tasks in collaborative engineering design. In our previous research, a web-based intelligent collaborative system was developed to address this challenge based on intelligent computational argumentation. However, two important issues were not resolved in that system: priority of participants and self-conflicting arguments. In this paper, we develop two methods for incorporating priorities of participants into the computational argumentation network: 1) weighted summation and 2) re-assessment of strengths of arguments based on priority of owners of the argument using fuzzy logic inference. In addition, we develop a method for detection of self-conflicting arguments. Incorporation …

Coupled-Mode Theory For Stimulated Raman Scattering In High-Q/Vm Silicon Photonic Band Gap Defect Cavity Lasers, Xiaodong Yang, C. W. Wong

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We examine the dynamics of stimulated Raman scattering in designed high-Q/V_m silicon photonic band gap nanocavities through the coupled-mode theory framework towards optically-pumped silicon lasing. The interplay of other X⁽³⁾ effects such as two-photon absorption and optical Kerr, related free-carrier dynamics, thermal effects, as well as linear losses such as cavity radiation and linear material absorption are included and investigated numerically. Our results clarify the relative contributions and evolution of the mechanisms, and demonstrate the lasing and shutdown thresholds. Our studies illustrate the conditions for continuous-wave and pulsed highly-efficient Raman frequency conversion for practical realization in monolithic silicon …

Impact-Induced Damage Characterization Of Composite Plates Using Neural Networks, Steve Eugene Watkins, Farhad Akhavan, Rohit Dua, K. Chandrashekhara, Donald C. Wunsch

Electrical and Computer Engineering Faculty Research & Creative Works

Impact-induced damage in fiber-reinforced laminated composite plates is characterized. An instrumented impact tower was used to carry out low-velocity impacts on thirteen clamped glass/epoxy composite plates. A range of impact energies was experimentally investigated by progressively varying impactor masses (holding the impact height constant) and varying impact heights (holding the impactor mass constant). The in-plane strain profiles as measured by polyvinylidene fluoride (PVDF) piezoelectric sensors are shown to indicate damage initiation and to correlate to impact energy. Plate damage included matrix cracking, fiber breakage, and delamination. Electronic shearography validated the existence of the impact damage and demonstrated an actual damage …

Efficient Sampling For Non-Intrusive Polynomial Chaos Applications With Multiple Uncertain Input Variables, Serhat Hosder, Robert W. Walters, Michael Balch

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The accuracy and the computational efficiency of a Point-Collocation Non-Intrusive Polynomial Chaos (NIPC) method applied to stochastic problems with multiple uncertain input variables has been investigated. Two stochastic model problems with multiple uniform random variables were studied to determine the effect of different sampling methods (Random, Latin Hypercube, and Hammersley) for the selection of the collocation points. The effect of the number of collocation points on the accuracy of polynomial chaos expansions were also investigated. The results of the stochastic model problems show that all three sampling methods exhibit a similar performance in terms of the the accuracy and the …

Adhesion-Delamination Mechanics Of A Prestressed Rectangular Film Adhered Onto A Rigid Substrate, Ming Fung Wong, Gang Duan, Kai-Tak Wan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A prestressed rectangular film clamped at both ends delaminates from a rigid punch. based on a thermodynamic energy balance, the delamination mechanics is derived to relate the simultaneous external tensile force applied to the punch, punch displacement, and contact area. Effects of the coupled tensile residual membrane stress and adhesion energy at the punch-film interface are investigated. a "pinch off" (stable shrinking of the contact area to a line) is predicted, contrasting the nonzero "pull-off" radius in a clamped circular film. the model is useful in understanding the behavior of various adhesion-delamination phenomena, especially in one dimensional capacitive microelectromechanical systems …

Multifrequency Eddy Current Inspection Of Corrosion In Clad Aluminum Riveted Lap Joints And Its Effect On Fatigue Life, Shridhar Natarajan, Anthony Chukwujekwu Okafor

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Aging aircraft are prone to corrosion damage and fatigue cracks in riveted lap joints of fuselage skin panels. This can cause catastrophic failure if not detected and repaired. Hence detection of corrosion damage and monitoring its effect on structural integrity are essential. This paper presents multifrequency eddy current (EC) inspection of corrosion damage and machined material loss defect in clad A1 2024-T3 riveted lap joints and its effect on fatigue life. Results of eddy current inspection, corrosion product removal and fatigue testing are presented.

Exploring Effective Methods For Simulating Damaged Structures With Geometric Variation: Toward Intelligent Failure Detection, Daniel A. Mcadams, David Comella, Irem Y. Tumer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Inaccuracies in the modeling assumptions about the distributional characteristics of the monitored signatures have been shown to cause frequent false positives in vehicle monitoring systems for high-risk aerospace applications. to enable the development of robust fault detection methods, this work explores the deterministic as well as variational characteristics of failure signatures. Specifically, we explore the combined impact of crack damage and manufacturing variation on the vibrational characteristics of beams. the transverse vibration and associated eigenfrequencies of the beams are considered. Two different approaches are used to model beam vibrations with and without crack damage. the first approach uses a finite …

Mechanical Characterization Of Spherical Hydrogels: Contact Diameter Measurement, Joshua Bunch

Opportunities for Undergraduate Research Experience Program (OURE)

In an effort to develop new ophthalmic treatments revolving around the ocular lens, the mechanical characteristics of natural ocular lenses and synthetic models must be determined and compared. One mechanical characteristic that is necessary when making comparisons is the variation of contact circle diameter or contact area with varying strains. A method was used in this experiment to measure the varying contact circle diameter of spherical hydrogels at strains up to 15%. This method could be used to estimate the varying contact diameter of other similar materials such as natural ocular lenses if the precision of the method is improved. …

Parallel Machine Tool Development, Adam Bunton

Opportunities for Undergraduate Research Experience Program (OURE)

The work done during this OURE centered on the parallel machining center that is under development by a research group led by Dr. R. Landers. The specific tasks associated with this research involved the design of several parts, documentation of the processes for assembly and operation, procurement of some materials and stock parts, and involvement with experiments with the machine tool. These various aspects are outlined in the following report, with emphasis on the design of components.

Concepts For The Nanosat- 5 Satellite Design Competition, Sunil C. Aggarwal

Opportunities for Undergraduate Research Experience Program (OURE)

This paper presents feasible small space satellite missions which are of interest to the U.S. Air Force and can be used to get selected and win the NANOSAT-5 satellite design competition. Some thought on which of these missions can be used by the University of Missouri-Rolla to successfully take part in the competition have also been presented.

Mechanical Fastener Pull-Out In Recycled Plastic Lumber, Ryan Dusheke

Opportunities for Undergraduate Research Experience Program (OURE)

The purpose of this paper is to present test results for the examination of mechanical fastener pull-out in plastic lumber. The testing was performed on both 1 Od galvanized steel nails, nominally 3" long and 0.148" in diameter, and No. 10 flathead low-carbon steel screws, nominally I" long. l "x6" Trimax plastic lumber, produced by US Plastic Lumber, was used for all testing. Tests were performed in each of the three sides of the boards. To evaluate the performance of the materials in varying conditions, testing was performed at -20°f, room temperature, and 125°f.

Magnetohydrodynamic Power Generation In A Scramjet Using A Post Combustor Generator, Nathan Lee Mundis

Masters Theses

"A scramjet with a post combustor MHD generator is examined. A quasi-one-dimensional model is developed to calculate the flow path from tip to tail. The model includes losses due to combustion irreversibility, incomplete combustion, chemically reacting flow, friction, MHD losses, and nozzle plume modeling. Flight Mach number, magnetic field strength, gas conductivity, MHD load factor, and MHD generator expansion angle are all varied in order to assess their effects on MHD power generated and thrust lost in the engine. The trends produced through the above variations are summarized in a set of model-fit equations. It is concluded that a post …

Computational Study Of Flow Over Elliptic Airfoils For Rotor/Wing Unmanned Aerial Vehicle Applications, Timothy William Assel

Masters Theses

"The purpose of this study will be to conduct a parametric investigation on the performance of elliptic airfoils for Rotor/Wing Unmanned Aerial Vehicles. The objective of this study is to conduct a two-dimensional, aerodynamic analysis on a various elliptic airfoil parameters, compare the reults of the analysis with theoretical predictions and experimental results, and evaluate handling and performance characteristics of Rotor/Wing UAVs during hover, transition, and forward flight"--Abstract, page iii.

A Guide To The Establishment Of A University Satellite Program, Abbie Marie Stewart

Masters Theses

"The UMR SAT team was formed at the University of Missouri-Rolla to design and build microsatellites. The team competed against ten other universities in the Nanosat 4 competition hosted by the Air Force Office of Scientific Research, the Air Force Research Laboratory, and the American Institute of Aeronautics and Astronautics. This document, written by the Chief Engineer, is a description of the process used by the UMR SAT team to develop a successful satellite program. Included in the document are methods based on systems engineering for developing a mission, a discussion of team organization and recruitment, and lessons learned during …

Low-Thrust Control Of A Lunar Orbiter, Nathan Harl

Masters Theses

"This thesis presents a method for maintaining a long-term lunar Sun-synchronous orbit using continuous low-thrust hardware. The control method is developed using optimal control theory, which involves controlling a system through the minimization of a desired cost function"--Abstract, page iii.

Refrigerant-Based Propulsion System For Small Spacecraft, Carl Reiner Seubert

Masters Theses

"The MR SAT spacecraft under development at UMR requires a propulsion system that can be utilized to perform orbital maneuvers and three-axis attitude control to complete its mission objective of conducting spacecraft formation flight. This thesis documents the research, analysis design and development of the cold gas propulsion system that was integrated on the MR SAT spacecraft"--Abstract, page iii.

Manufacturing Of Glass Ribbon Reinforced Transparent Composites Using The Autoclave Process, Josef Patrick Seale

Masters Theses

"Clear transparent panels have many applications ranging from windows on an aircraft to protective safety guards on industrial equipment. Glass ribbon reinforced transparent composites are light weight, load bearing and have a high impact resistance.

A transparent composite is based on the concept of matching the refractive index of the glass ribbon with that of a resin system. It is not necessary that the resin refractive index match the glass refractive index before the cure cycle, only that the refractive indexes match after curing.

Transparent composites have a high impact resistance that would be mechanically ideal for aircraft windows and …

Configuration, Manufacture, Assembly, And Integration Of A University Microsatellite, Lori Ann Ziegler

Masters Theses

"The Space Systems Engineering Team at the University of Missouri-Rolla (UMR), in conjunction with a number of Air Force, NASA, and industry mentors, is working toward the design, development, and launch of its first satellite, UMR SAT (University of Missouri-Rolla Satellite). This thesis documents the design of the UMR SAT satellites, specifically focusing attention on the layout of all components, component boxes designed for containment and protection from electromagnetic interference and the attachment of components inside the boxes and the boxes to the structure. This thesis also discusses the development of UMR SAT with challenges faced in manufacturing and prototyping …

Determination Of Laser Absorption Coefficients Of Gas Mixtures Using An Ab Initio Md Model, Zhi Liang, Hai-Lung Tsai, Lan Jiang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In an Effort to Study the Laser Induced Dissociation of Gas Mixtures for an Ongoing Research Project on Diamond Thin Film Coating using Multiple Lasers, It is Necessary to Determine the Absorption Coefficient of Laser Energy by CO2 Gas. an Ab Initio Molecular Dynamics (AIMD) Model is Used to Determine the Laser Absorption Coefficient of CO2 Gas as a Function of Laser Wavelength and Gas Temperature. the Translational, Rotational, and Vibration Motions of Molecules Are All Taken into Account in Our Model. the Intra-Molecular Potential Energy is Obtained by Solving the Kohn-Sham Equation. the Projector-Augmented Wave (PAW) Exchange-Correlation Potential Function …

Neural Network Controller Development And Implementation For Spark Ignition Engines With High Egr Levels, Jonathan B. Vance, Atmika Singh, Brian C. Kaul, Jagannathan Sarangapani, J. A. Drallmeier

Electrical and Computer Engineering Faculty Research & Creative Works

Past research has shown substantial reductions in the oxides of nitrogen (NOx) concentrations by using 10% -25% exhaust gas recirculation (EGR) in spark ignition (SI) engines (see Dudek and Sain, 1989). However, under high EGR levels, the engine exhibits strong cyclic dispersion in heat release which may lead to instability and unsatisfactory performance preventing commercial engines to operate with high EGR levels. A neural network (NN)-based output feedback controller is developed to reduce cyclic variation in the heat release under high levels of EGR even when the engine dynamics are unknown by using fuel as the control input. A separate …