Aerospace Engineering Commons^™

Modal Analysis Of Composite Structures With Damping Material, Kellie Michelle Tremaine

Master's Theses

The purpose of this study is to develop an analytical solution for modal analysis of actively damped orthotropic composite plates in bending and to verify it with experimental analysis.

The analytical modal analysis solution for composite plate dynamics is derived using Euler theory. This analysis applies to structures with orthotropic lamina of uniform material properties at any lamination angle. The bending-extensional coupling can be neglected for plates that are symmetric or approximately symmetric, which allows an exact solution for natural frequency and mode shape to be obtained. An exact solution can be found for natural vibration and in general.

The …

Day/Night Band Imager For A Cubesat, Eric Stanton

Electrical Engineering

Day/Night Band (DNB) earth sensing and meteorological systems like the Defense Meteorological Satellite Program (DMSP) Operational Linescan System (OLS) provide visible wavelength imagery 24 hours a day that is used primarily for cloud imaging in support of weather forecasting. This paper describes a compact push-broom imager that meets low light imaging requirements for DMSP OLS and the NOAA/NASA Joint Polar Satellite System (JPSS) as documented in the Integrated Operational Requirements Document [1] (IORD) including the imager design, system level concepts of operation for data collection, radiometric and spatial calibration, and data transmission to Earth. This small, lightweight imager complies with …

Analysis And Testing Of Heat Transfer Through Honeycomb Panels, Daniel D. Nguyen

Aerospace Engineering

This project attempts to simulate accurately the thermal conductivity of honeycomb panels in the normal direction. Due to the large empty space of the honeycomb core, the thermal radiation mode of heat transfer was modeled along with conduction. Using Newton’s Method to solve for a steady state model of heat moving through the honeycomb panel, the theoretical effective thermal conduction of the honeycomb panel was found, ranging from 1.03 to 1.07 Q/m/K for a heat input of 2.5 W to 11.8 W. An experimental model was designed to test the theoretical results, using a cold plate and a heat plate …

Sun-Synchronous Orbit Slot Architecture Analysis And Development, Eric Watson

Master's Theses

Space debris growth and an influx in space traffic will create a need for increased space traffic management. Due to orbital population density and likely future growth, the implementation of a slot architecture to Sun-synchronous orbit is considered in order to mitigate conjunctions among active satellites. This paper furthers work done in Sun-synchronous orbit slot architecture design and focuses on two main aspects. First, an in-depth relative motion analysis of satellites with respect to their assigned slots is presented. Then, a method for developing a slot architecture from a specific set of user defined inputs is derived.

An Inverse Design Method For Supersonic Airfoils, Steven Edward Skare

Master's Theses

Airfoil design is one of the most important aspects of aircraft design. Slight changes in airfoil geometry can lead to significant changes in a wide variety of aircraft performance metrics. Inverse design methods offer an efficient alternative to standard direct methods. The key to this design problem is to derive a direct relationship between changes in airfoil geometry and changes in pressure or velocity distributions. This relationship is then used to modify an initial airfoil and its pressure distribution to match a target pressure distribution, which is specified by design parameters. At this point, the engineer now has a final …

Primary And Secondary Flow Interactions In The Mixing Duct Of A 2-D Planer Air Augmented Rocket, Martin Roy Popish

Master's Theses

Experiments were conducted on the Cal Poly air augmented rocket (AAR) in order to characterize two-dimensional flowfield phenomenon occurring in the mixing duct. The testing utilized a direct connect system where high pressure nitrogen is fed into the combustion chamber, to form a primary flow. The high pressure nitrogen is then expanded through a nozzle, with an area ratio of 22 and an exit area of 0.75 in², up to Mach 4.3. Secondary air is entrained from a plenum chamber which is used to create a lower stagnation pressure for the secondary flow. The two flows mix in …

Aerodynamics Of An Aerofoil In Transonic Ground Effect: Numerical Study At Full-Scale Reynolds Numbers, G. Doig, T. J. Barber, A. J. Neely, D. D. Myre

Aerospace Engineering

The potential positive effects of ground proximity on the aerodynamic performance of a wing or aerofoil have long been established, but at transonic speeds the formation of shock waves between the body and the ground plane would have significant consequences. A numerical study of the aerodynamics of an RAE2822 aerofoil section in ground effect flight was conducted at freestream Mach numbers from 0·5 to 0·9, at a range of ground clearances and angles of incidence. It was found that in general the aerofoil's lifting capability was still improved with decreasing ground clearance up until the point at which a lower …

Electromagnetic Railgun Safety, Sven Ericson

Aerospace Engineering

The Cal Poly Electromagnetic Railgun is a system that with the proper precautions can be safely operated. Changes in plugs and boxes insure that the systems cannot be improperly wired, reducing the chances of accidental discharge. By covering exposed wires the system is safe to store as long as the voltage is checked before any maintenance is performed. Updates in procedures remove the possibility of injury to personnel and allow the railgun to be fired repeatedly under similar circumstances. Defined roles for the operators’ decreases confusion and allows people to concentrate on their area during testing. As hardware changes it …

Simulation Of Blood Flow And Nanoparticle Transport In A Stenosed Carotid Bifurcation And Pseudo-Arteriole, Graham Doig, Guan H. Yeoh, Victoria Timchenko, Gary Rosengarten, Tracie J. Barber, Sherman C.P. Cheung

Aerospace Engineering

Numerical simulation of flow through a realistic bifurcated carotid artery geometry with a stenosis has been conducted for comparison to experimental measurements. The behaviour of simplified therapeutic nanoparticles in relatively low concentration was observed using a discrete particle approach. The role of size (diameters from 500 nm to 50 nm) in determining particle residence time and the potential for both desirable and undesirable wall interactions was investigated. It was found that mean particle residence time reduced with decreasing particle diameter, and the percentage of particles experiencing one or more wall interactions increased simultaneously. Further simulations were conducted on a scaled-down …

Investigating Various Propulsion Systems For An External Attachment For A Controlled-Manual De-Orbit Of The Hubble Space Telescope, Nelson De Guia

Aerospace Engineering

This reports explains the results for a proposed senior project. This project concerns the Hubble Space Telescope, and exploring the possibility of having an external propulsion attachment for a manual de-orbit. The Hubble Space Telescope was proposed to return to Earth via the Space Shuttle. Although, through the current U.S. Space Administration, the Space Shuttle has been retired before the Hubble Space Telescope was retrieved. By completing this project, the results could provide insight to what type of propulsion would best de-orbit the Hubble upon its retirement. Different propulsion systems were considered to attempt to determine an optimal attachment, varying …

Aerial Deployable Autonomous Solar Powered Glider, Brandon Groshong, Jacob Ohana

Aerospace Engineering

Awareness of green solutions to powered flight is a new trend taking the Aerospace Industry by storm. One particular application that shows high promise is that of photovoltaics on small UAV-type aircraft to help extend flight time. The purpose of this report is to document both research and experimentation performed on a small RC aircraft in order to better understand the electrical requirements of such a device. Using that research, speculation on how it can be used to design a mobile Aerial Deployable Autonomous Solar Powered Glider will be performed. Technologies such as CIGS solar cells and Lithium Polymer batteries …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

Nonlinear Uav Flight Control Using Command Filtered Backstepping, Brian M. Borra

Master's Theses

The aim of this effort is to implement a nonlinear flight control architecture, specifically flight path control via command filtered backstepping, for use in AME UAS's Fury® 1500 unmanned flying wing aircraft. Backstepping is a recursive, control-effort minimizing, constructive design procedure that interlaces the choice of a Lyapunov function with the design of feedback control. It allows the use of certain plant states to act as intermediate, virtual controls, for others breaking complex high order systems into a sequence of simpler lower-order design tasks.

Work herein is a simplified implementation based on publications by Farrell, Sharma, and Polycarpou. Online approximation …

Experimental Investigation Of A 2-D Air Augmented Rocket: High Pressure Ratio And Transient Flow-Fields, Josef S. Sanchez

Master's Theses

A 2-D Air Augmented Rocket, the Cal Poly Air Augmented Rocket (CPAAR) Test Apparatus operating as a mixer-ejector was tested to investigate high stagnation pressure ratio and transient flow fields of an ejector. The primary rocket ejector was supplied with high pressure nitrogen at a maximum chamber pressure of 1758 psia and a maximum mass flow rate of 1.4 lb/s. The secondary flow air was entrained from a fixed volume plenum chamber producing pressures as low as 3.3 psia. The maximum total pressure ratio achieved was 221. The original CPAAR apparatus was rebuilt re-instrumented and capability expanded. A fixed volume …

The Importance And Challenge Of Launch Environment Testing, Christina Diaz

Aerospace Engineering

This report discusses the purpose and effect of environmental testing, particularly vibration, shock and acoustic tests, in the aerospace industry. Vibration, shock, and acoustic testing are methods that are used to quantify and analyze the physical phenomenon of the launch environment on a payload or launch vehicle. The importance of innovation in testing and understanding of failures is crucial to a successful spacecraft mission. The advancement and precision of these testing methods is also explored in this report such as the invention of the 6 Degree of Freedom (DoF) vibration table and solutions to data acquisition issues recently discovered in …

Effect Of End-Plate Tabs On Drag Reduction Of A 3d Bluff Body With A Blunt Base, Jarred Michael Pinn

Master's Theses

This thesis involves the experimental testing of a bluff body with a blunt base to evaluate the effectiveness of end-plate tabs in reducing drag. The bluff body is fitted with interchangeable end plates; one plate is flush with the rest of the exterior and the other plate has small tabs protruding perpendicularly into the flow. The body is tested in the Cal Poly 3ft x 4ft low speed wind tunnel. Testing is conducted in three phases.

The first phase was the hot-wire measurement of streamwise velocity of the near wake behind the bluff body. An IFA300 thermal anemometry system with …

Pico-Satellite Integrated System Level Test Program, Marcus A. Ruddy

Master's Theses

Testing is an integral part of a satellite’s development, requirements verification and risk mitigation efforts. A robust test program serves to verify construction, integration and assembly workmanship, ensures component, subsystem and system level functionality and reduces risk of mission or capability loss on orbit.

The objective of this thesis was to develop a detailed test program for pico-satellites with a focus on the Cal Poly CubeSat architecture. The test program established a testing baseline from which other programs or users could tailor to meet their needs. Inclusive of the test program was a detailed decomposition of discrete and derived test …

Experimental Investigation Of Suction Slot Geometry On A Goldschmied Propulsor, Nicole M. Thomason

Master's Theses

The Goldschmied Propulsor concept combines boundary layer suction and boundary layer ingestion to improve propulsive efficiency and reduce drag on an axisymmetric body. This investigation of a Goldschmied Propulsor aimed to determine influential characteristics of the suction slot geometry to aid in better slot geometry design and to decrease the suction flow requirements for maintaining attached flow over the entire model surface. The Propulsor model was 38.5 inches in length with a max diameter of 13.5 inches. Three suction slot geometries were investigated with the addition of aluminum cusps to the slot entrance. The cusps varied in the distance they …

Design And Analysis Of A Reusable N2o-Cooled Aerospike Nozzle For Labscale Hybrid Rocket Motor Testing, Daniel Joseph Grieb

Master's Theses

A reusable oxidizer-cooled annular aerospike nozzle was designed for testing on a labscale PMMA-N₂0[1] hybrid rocket motor at Cal Poly-SLO.[2] The detailed design was based on the results of previous research involving cold-flow testing of annular aerospike nozzles and hot-flow testing of oxidizer-cooled converging-diverging nozzles. In the design, nitrous oxide is routed to the aerospike through a tube that runs up the middle of the combustion chamber. The solid fuel is arranged in an annular configuration, with a solid cylinder of fuel in the center of the combustion chamber and a hollow cylinder of fuel lining …

Dynamic Model Creation And Scripting Support In The Horizon Simulation Framework, Brian Jeffrey Butler

Master's Theses

Dynamic model creation and support for the Lua scripting language was added to the Horizon Simulation Framework used for the verification and validation of system-level requirements. The addition of scripting support allows for subsystem models and their algorithms to be defined using a simpler scripting language, rather than C++. The Luabind library by Rasterbind software is used to expose the C++ algorithms and classes to Lua that are already defined in the framework. Interoperability between Lua and C++ code allows for the ease of use of a scripting language while utilizing the utility classes and functions already created. The dynamic …

Aircraft Operations Based Mission Requirements, Robert A. Mcdonald

Aerospace Engineering

The mission capabilities of aircraft in the current commercial fleet are a combined result of many factors. The launch customer for each aircraft has a voice in determining the requirements. The manufacturer desires to best position the aircraft in the market considering their own aircraft and their competitors aircraft it will replace and compete with. Consequently, anyone considering the development of an aircraft to compete with or replace an aircraft in-service must do more than simply choose to meet the capabilities of that aircraft. This is especially true when unconventional systems are considered; the fundamental trade-offs for these systems may …

Wind Tunnel Modeling Of Small Electric Uav Power System Performance, Nathan R. Phelps

Aerospace Engineering

This report details the design and construction of a testing apparatus for characterization of small electric aircraft power systems designed for use in the California Polytechnic State University San Luis Obispo Aerospace Engineering department’s subsonic wind tunnel. This apparatus was constructed and implemented with the goal of determining system and component efficiencies of an entire power system using RC Aircraft components as an analog for systems currently in use in the current generation of small electric UAV’s in service with the US Armed Forces. The goal of these experiments was to determine where improvements in the system architecture can be …

Radiation In The Space Environment, Sally Hermansen, Jennifer Shatts

Aerospace Engineering

No abstract provided.

Global Optimization Of Mga-Dsm Problems Using The Interplanetary Gravity Assist Trajectory Optimizer (Igato), Jason M. Bryan

Master's Theses

Interplanetary multiple gravity assist (MGA) trajectory optimization has long been a field of interest to space scientists and engineers. Gravity assist maneuvers alter a spacecraft's velocity vector and potentially allow spacecraft to achieve changes in velocity which would otherwise be unfeasible given our current technological limitations. Unfortunately, designing MGA trajectories is difficult and in order to find good solutions, deep space maneuvers (DSM) are often required which further increase the complexity of the problem. In addition, despite the active research in the field over the last 50 years, software for MGA trajectory optimization is scarce. A few good commercial, and …

Experimental Investigation Of A 2-D Air Augmented Rocket: Effects Of Nozzle Lip Thickness On Rocket Mixing And Entrainment, Trevor Allen Montre

Master's Theses

Cold-flow tests were performed using a simulated Air Augmented Rocket (AAR) operating as a mixer-ejector in order to investigate the effects of varied primary nozzle lip thickness on mixing and entrainment. The simulated primary rocket ejector was supplied with nitrogen at a maximum chamber stagnation pressure of 1712 psi, and maximum flow rate of 1.67 lb_m/s. Secondary air was entrained from a plenum, producing pressures as low as 6.8 psi and yielding maximum stagnation pressure ratios as high as 160. The primary ejector nozzles each had an area ratio of approximately 20, yielding average primary exit Mach numbers …

Aircraft Longitudinal Control Experiment, Dustin Schaff

Aerospace Engineering

This paper describes the design, fabrication, and analysis of an experiment that demonstrates the stability and control system characteristics of an aircraft constrained at the center of gravity in an air flow field. Given a set of basic requirements, the physical system (including the airframe, wings, tail, and mounted ball bearing) was designed, modeled, and manufactured. With the aircraft placed in front of a fan and allowed to rotate freely with the ball bearing, an angular rate sensor and servo motor to the deflect the elevator may be connected to any computer using an analog/digital Data Acquisition (DAQ) device to …

Cubesat Constellation Analysis For Data Relaying, Bradley Ryan Smalarz

Master's Theses

Current CubeSat communication technology limits the amount of time, and number of accesses with ground stations. It has been proposed to use a constellation of CubeSats to improve relay performance and increase the number of accesses between a CubeSat and ground stations. By using the spatial and temporal analysis features of STK, coupled with the STK/Matlab interface a robust tool was created to analyze the performance of CubeSat constellations based on a store-and-forward communications model which is not currently supported by the STK Engine. Utilizing the Connect messaging format through a socket connection on the local machine, a Matlab graphical …

Comet: Constrained Optimization Of Multiple-Dimensions For Efficient Trajectories, Michael Curt Conrad

Master's Theses

The paper describes the background and concepts behind a master’s thesis platform known as COMET (Constrained Optimization of Multiple-dimensions for Efficient Trajectories) created for mission designers to determine and evaluate suitable interplanetary trajectories. This includes an examination of the improvements to the global optimization algorithm, Differential Evolution, through a cascading search space pruning method and decomposition of optimization parameters. Results are compared to those produced by the European Space Agency’s Advanced Concept Team’s Multiple Gravity Assist Program. It was found that while discrepancies in the calculation of ΔV’s for flyby maneuvers exist between the two programs, COMET showed a noticeable …

Formulation Of An Optimal Search Strategy For Space Debris At Geo, Daniel J. Jackson

Master's Theses

The purpose of this thesis is to create a search strategy to find orbital debris when the object fails to appear in the sky at its predicted location. This project is for NASA Johnson Space Center Orbital Debris Program Office through the MODEST (Michigan Orbital Debris Survey Telescope) program. This thesis will build upon the research already done by James Biehl in “Formulation of a Search Strategy for Space Debris at GEO.” MODEST tracks objects at a specific right ascension and declination. A circular orbit assumption is then used to predict the location of the object at a later time. …

Implementation And Validation Of The Ζ-F And Asbm Turbulence Models, Dustin Van Blaricom Quint

Master's Theses

The use of Computational Fluid Dynamics (CFD) tools throughout the engineering industry has become standard. Simulations are used during nearly all steps throughout the life cycle of products including design, production, and testing. Due to their wide range of use, industrial CFD codes are becoming more flexible and easier to use. These commercial codes require robustness, reliability, and efficiency. Consequently, linear eddy viscosity models (LEVM) are used to model turbulence for an increasing number of flow types. LEVM such as k-ε and k-ω provide modeling with little loss of computational efficiency and have proven to be robust. The LEVM that …