Considerations For Numerical Modeling Of Inverted Wings In Ground Effects, Graham Doig, Tracie J. Barber

Aerospace Engineering

No abstract provided.

Performance Analysis Of A Variable Conductance Heat Pipe, Herron Arreola

Aerospace Engineering

This report examines the analysis of a donated Boeing variable conductance heat pipe with unknown performance characteristics. These characteristics were found through experimental means by utilizing 14 thermocouples attached to various locations on the heat pipe, the heaters and to the insulation. Although the maximum axial heat transport capability could not be determined due to the limited number of strip heaters available, the maximum radial heat flux capability of the heat pipe was found to be 2.46 W/in². The experiment also revealed that increasing the input power decreased the burn out inclination angle and that using a coolant …

Constrained Hermite Tls For Mesh-Free Derivative Estimation Near And On Boundaries, Robert A. Mcdonald, Alejandro Ramos

Aerospace Engineering

A Taylor series least-squares approach to estimating derivatives on scattered data is extended to include derivative observation or specification. This approach allows improved estimation of derivatives near boundaries as compared with the standard ghost node approach. It also enables a unique method of estimating derivatives in a surface using only surface data.

An Automated Test Station Design Used To Verify Aircraft Communication Protocols, Joshua Berrian

Master's Theses

Requirements verification is typically the costliest part of the systems engineering design process. In the commercial aircraft industry, as the software and hardware design evolves, it must be verified to conform to requirements. In addition, when new design releases are made, regression analysis must be performed which usually requires repeat testing. To streamline verification, a suite of automated verification tools is described in this document which can reduce the test effort. This test suite can be qualified to be used to verify systems at any DO-178B design assurance level. Some of the software tools are briefly described below.

There are …

Mission Performance Considered As Point Performance In Aircraft Design, Robert A. Mcdonald

Aerospace Engineering

The cruise or loiter performance of an aircraft is intimately tied to its wing loading and its thrust-to-weight ratio. Paradoxically, mission performance is often not considered when these fundamental aircraft parameters are determined in conceptual design. In this paper, the traditional constraint diagram is extended to include contours of range or endurance parameter. These performance metrics represent the mission-performance capability of the aircraft without sizing the aircraft to a particular mission. This gives the designer an immediate and intuitive understanding of the tradeoff between the point and mission performance of the aircraft. The potential freedom for the designer to choose …

Flow Characteristics Of The Renovated Cal Poly 3 X 4 Ft Subsonic Wind Tunnel, Mathew L. Thomas, Dorian V. Pandey, Jason N. Nguyen

Aerospace Engineering

This paper investigates the flow characteristics of the renovated Cal Poly 3 x 4 ft subsonic wind tunnel. The IFA 300 constant-temperature anemometer along with a cross-plane X-wire dual-sensor probe was used to measure the mean velocity and turbulence intensity of the tunnel flow and part of the turbulent boundary layer at one section of the tunnel. Because of the malfunction of one channel of the IFA 300, only one wire of the dual sensor probe was calibrated for the measurements. The probe was then placed in a streamlined probe holder mounting on the traverse inside the wind tunnel. The …

Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer

Master's Theses

The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …

Sitting In The Pilot's Seat: Optimizing Human-Systems Interfaces For Unmanned Aerial Vehicles, Steven Michael Queen, Kurt Sanner

STAR Program Research Presentations

One of the pilot-machine interfaces (the forward viewing camera display) for an Unmanned Aerial Vehicle called the DROID (Dryden Remotely Operated Integrated Drone) will be analyzed for optimization. The goal is to create a visual display for the pilot that as closely resembles an out-the-window view as possible. There are currently no standard guidlines for designing pilot-machine interfaces for UAVs. Typically, UAV camera views have a narrow field, which limits the situational awareness (SA) of the pilot. Also, at this time, pilot-UAV interfaces often use displays that have a diagonal length of about 20". Using a small display may result …

Simulation Of Wing Tip Vortices, Ryan Termath, Jason Lechniak, Keerti Bhamidipati

STAR Program Research Presentations

Modeling and Simulation (M&S) computational fluid dynamics (CFD) techniques were used to better understand wing tip vortices about a wing section. The CFD results were compared to experimental wind tunnel data derived from the University of Iowa (Ref. 2). The experiment used Stereoscopic Particle Image Velocimetry (SPIV) to measure the flow field. The SPIV data from the experiment illustrates the vortex core development and behavior downstream of the trailing edge of the wing section. Three CFD simulations using various mesh sizes and time steps were completed and compared to the experimental results. Two dimensional plots of modeled local flow field …

Unsteady Total Pressure Measurement For Laminar-To-Turbulent Transition Detection, Akane Sharon Karasawa

Master's Theses

This thesis presents the use of an unsteady total pressure measurement to detect laminar-to-turbulent transition. A miniature dynamic pressure transducer, Kulite model XCS-062-5D, was utilized to measure the total pressure fluctuations, and was integrated with an autonomous boundary layer measurement device that can withstand flight test conditions. Various sensor-probe configurations of the Kulite pressure transducer were first examined in a wind tunnel with a 0.610 m (2.0 ft) square test section with a maximum operational velocity of 49.2 m/s (110 mph), corresponding dynamic pressure of 1.44 kPa (30 psf). The Kulite sensor was placed on an elliptical nose flat plate …

Comparison Of A High Purity Germanium Gamma Ray Spectrometer And A Multidimensional Nai(T1) Scintillation Gamma Ray Spectrometer, Greg Stratton

Aerospace Engineering

This report compares two different gamma ray spectrometers in terms of performance, operation, and apparatus and also investigates the design and integration challenges of using gamma ray spectrometers in space. The first spectrometer is a one-dimensional high purity germanium (HPGe) spectrometer and the second is a multidimensional NaI(Tl) scintillation spectrometer (MGRS). The key results show that the HPGe exhibits 15 to 27 times better energy resolution than the MGRS, but the MGRS is 52 times more sensitive and removes 177 % more of the background radiation.

3d Cfd On An Open Wheel Race Car Front Wing In Ground Effects, Thomas A. Price

Aerospace Engineering

The purpose of the report is to investigate the ability of the Fluent 6.3 k-ε Realizable turbulence model with standard wall functions to model the flow around the front wing of Cal Poly’s 2008 Formula SAE car. The three primary areas of interest are ground effects, the wing wheel interaction, and the wing tip vortices. Fluent was successful at modeling the increase suction from the ground effects, and the upwash due to the wing tip vortices. The results also displayed how the high pressure region in front of the tire propagates forward and interacts with the pressure distribution around the …

Analysis And Design Of A Propulsion System Trade Study Tool For A Boeing 376 Series Communications Satellite, Kevin Dunk

Aerospace Engineering

No abstract provided.

The Effects Of Damage Arrestment Devices In Composite Plate Sandwiches With Fastener Holes, Mark Anderson, Nancy Hung Choy, Lacey Jones, Rita Kourskaya

Aerospace Engineering

Composite materials such as a carbon fiber are used in a variety of new technologies including aircraft, spacecraft, and motor vehicles. Carbon fiber has a high strength to weight ratio, a key advantage over other material options. This report discusses the use of composite damage arrestment devices (DADs) in composite sandwich panels with a foam core. There are three different curing cycles tested for the DADs: pressure only, vacuum only, and vacuum with 1000 lbs of pressure. Using a Tetrahedron Heat Press to cure the composite specimen and an Instron Machine to perform tensile testing, data was collected for each …

Composite I-Beam Fabrication And Testing In Response To 14th Annual Sampe Bridge Competition, Kodi Rider, Niño Noel Las Piñas, Hans Mayta

Aerospace Engineering

Composites are a type of material that generally combines two materials yielding mechanical properties that are different than its constituent parts. These constituents are classified as either a fiber or a matrix. The objective of this project is to create a carbon-fiber composite I-beam that meets the specifications of the SAMPE student bridge competition. The I-beam consists of carbon fiber unidirectional and woven laminas, as well as aluminum honeycomb and high density polystyrene foam to stiffen the structure. The bridge contest rules limit the dimensions and weight of the bridge. The cross-section must be within 4 inches x 4 inches …

Thermal Analysis Of The Cubesat Cp3 Satellite, Jonas Friedel, Sean Mckibbon

Aerospace Engineering

Due to inconsistencies found in the on-orbit thermal data from the CubeSat CP3 satellite between 2007 and 2011, further analysis is performed on a larger number of data from August 2010 through April 2011, aiming to find an explanation for the overall increasing measured temperatures and shortening peak periods. Therefore, the satellite power data as well as orbital anomalies are analyzed leading to the conclusion that the satellite was temporarily (January – March 2011) orbiting with significantly increased sun exposure causing the higher temperatures. The shortened temperature peak periods are explained by alternating albedo values as the main influence in …

Determination Of The Surface Boundary Layer Using A Quadrotor, Andrew Haviland

Aerospace Engineering

Wind velocity data was taken by a quadrotor UAV using accelerometers, gyroscope, and a barometer. Data was taken at different altitudes over a single position to determine the boundary layer at the surface of the earth. The data taken was compared to the results from numerical methods to determine if this is a practice application for a quadrotor. A few weeks before the test was set to get underway, the quadrotor suffered a very hard crash while testing the GPS and altitude hold function and wasn’t able to completely recover from it. Theoretical results and experiment proposal are covered. 

Design, Manufacturing And Testing Of An Environmentally-Green Bipropellant Thruster, Alex Bendoyro, Gabriel Sanchez, Erin Stearns, Phillip Takahashi

Aerospace Engineering

This project reviews the design, manufacturing and experimentation process of a green bi-propellant thruster designed to output 5 lbf. The goals were to successfully design, manufacture and test a thruster, while discovering the complications that arise through out the complete design process of a green thruster. The thruster was successfully designed using ideal rocket equations and the design was successfully confirmed using CFD and FEA. Manufacturing of the thruster was fully planned and revealed mild flaws in thruster design. For example some features were not manufacturable to the exact measurements desired. Testing of the engine gave results inconsistent with expected …

Design, Fabrication, And Testing Of An Electromagnetic Rail Gun For The Repeated Testing And Simulation Of Orbital Debris Impacts, Jeff Maniglia, Jordan Smiroldo, Alex Westfall, Guy Zohar

Aerospace Engineering

An Electromagnetic Railgun (EMRG) was designed, built, and tested, capable of firing a projectile a 1 gram projectile at 650 m/s muzzle velocity. The EMRG utilizes an injector, a high voltage power supply, a capacitor bank, inductors and rails. The injector fires 2300 psig Nitrogen gas into the system to provide an initial velocity. The high voltage power supply charges the capacitor bank. The capacitor bank discharges the electric potential built up through the projectile while inside the rails in order to create the EMRG’s force. The inductors are used to pulse form the capacitor bank in order to get …

An Analysis Of Stabilizing 3u Cubesats Using Gravity Gradient Techniques And A Low Power Reaction Wheel, Erich Bender

Aerospace Engineering

The purpose of this paper is to determine the feasibility of gravity gradient stabilizing a 3U CubeSat and then using a miniature reaction wheel to further increase stability characteristics. This paper also serves as a guide to understanding and utilizing quaternions in attitude control analysis. The analytical results show that using 33 centimeter booms and 400 gram tip masses, a 3U CubeSat will experience a maximum of 6 degrees of angular displacement in yaw and pitch, and less than .5 degrees of angular displacement in the nadir axis. A .120 kilogram miniature reaction wheel developed by Sinclair Interplanetary was introduced …

Study Of The Effect Of Different Lay-Up Methods On The Composite Mechanical Characteristics, Veronica Cuevas, Walter Ely Salguero

Aerospace Engineering

The purpose of this experiment is to investigate and understand composite structures and the effect of different layup methods on the composite structure, particularly a composite I-beam. One must learn the procedure on how to build the composite I-beam and put it together then build the final composite I-beam and enter the I-beam in the 14^th Annual Society for the Advancement of Material and Process Engineering (SAMPE) Student Bridge Contest. The competition will be held May 25^th, 2011 in Long Beach, CA. The I-beam was entered in the competition and placed 4^th out of 5. The …

Electric Aircraft Propulsion Test Rig Design & Fabrication, Ryan Mayer, Brian Kubicki, Bradley Rodriguez, Austin Harris, David Caudle

Aerospace Engineering

An electric aircraft propulsion test rig was designed and fabricated to predict thrust, torque and battery discharge profiles for an electric aircraft. The original unit was purchased from ElectraFlyer and included the DC brushless motor, carbon fiber propeller, charger, electronic controller and lithium polymer batteries. Various components were constructed and purchased in order to fabricate the optimal test rig apparatus. This apparatus allows for simultaneous measurement of the torque and thrust of the system through the use of a biaxial sensor. The test rig also measures system voltage and current, which allows the user to determine the discharge profile of …

An Investigation Of Dynamic Soaring And Its Applications To The Albatross And Rc Sailplanes, Christopher J. Lee

Aerospace Engineering

Dynamic soaring is a technique used by the sea bird the Albatross. This technique allows for the bird to stay in the air for extended periods of time with very little effort. Dynamic soaring utilizes the wind gradient on the surface of the ocean to maintain its airspeed. A similar technique is used by RC glider pilots to achieve high speeds by using the shear wind layer on the leeward side of mountain ridges.

Analysis And Design Of An Affordable High Altitude Rocket System, Brian Cooper

Aerospace Engineering

This paper discusses the design of the Rarefied High-Altitude Zenith Experimental Rocket (RHAZER) which is launched at an altitude of 35 kilometers from a weather balloon. The weather balloon is capable of carrying up to 2 kilograms of payload to this altitude, and the rocket can carry a payload of approximately 150 grams to an altitude of at least 80 kilometers and be recovered safely after landing. It is designed to be aerodynamically stable at its launch point, while using fins to spin-stabilize before it enters the low-pressure upper atmosphere. This system has been designed to be used as an …

An Analysis Of N-Body Trajectory Propagation, Emerson Frees Ii

Aerospace Engineering

Trajectories created with n-body orbit models were propagated in geocentric and interplanetary test cases. The n-body models were created in MATLAB^® using numerical integration. In the geocentric test case, the n-body codes were compared to a two-body orbit model and to the default HPOP model used in Satellite Tool Kit^®. The interplanetary test case compared the n-body model to the HORIZONS ephemeris data from JPL and an equation for ephemeris propagation. Both cases used the same initial positions and velocities and were propagated for the same duration. The results of the analysis showed that while n-body models …

Development And Design Of A Hovering Controller For Operation In A Dynamic Asteroid Environment, Nicholas Georgiades

Aerospace Engineering

The project seeks to develop a dynamic model similar to that present near a solar system small body, and to design a controller suggested in other resources that will allow a spacecraft operating in this environment to hover in a fixed location in the relative reference frame of the small body. The paper discusses the derivation of the equations of motion used in the non-linear dynamic model, the design of the controller that will allow the spacecraft to hover, and the development of the control loop that will simulate the spacecraft hovering in the dynamic environment of the asteroid 1999 …

Flexi-Focus Lens: Pdms Variable Focal Length Lens, Patrick Angulo, Alex Doyle, Dylan Mcdaniel, Michael Olivarez

Industrial and Manufacturing Engineering

The design of a variable focal length, or flexi-focus, polydimethylsiloxane (PDMS) lens incorporating a light emitting diode (LED) source is intended for future use on board commercial aircraft. Specifically, the design is intended for the Boeing 787 Dreamliner aircraft, serving as a personal reading light for the passengers seated in the cabin. Most current reading lights on board aircraft are rigid, incandescent, and have very limited freedom in terms of adjusting the emitted light. Incandescent lamps are also inefficient with respect to energy consumption and light output as well as a high heat output. In an economy of increasing demand …

Human Powered Helicopter: Observing The Impacts Of Ground Effect And Intermeshed Rotors, Shane Stowe

Physics

No abstract provided.

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …