Aerospace Engineering Commons^™

Effect Of Multifunctional Material On The Mechanical Behavior Of Composite Structure Using Finite Element Analysis, Nicholas A. Romonoski

Aerospace Engineering

No abstract provided.

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Thermal Vacuum Integration For Cal Poly's Space Environments Laboratory, Chelsea Barackman, Steven Jackowski

Aerospace Engineering

The purpose of the senior project is to construct a thermal vacuum by utilizing a preexisting vacuum chamber in the Space Environments Lab, and a donated Advanced Thermal Sciences (ATS) chiller. While a thermal vacuum is already available on campus, building one for the Space Environments Lab would grant undergraduates access to the equipment, allowing a much better understanding of testing methods and procedures in use by the aerospace industry. This paper explains the design and analysis of the thermal vacuum (T-VAC) project as well as the operation and procedures required for the ATS chiller and fill/drain tank. The thermal …

The Synergistic Integration Of Computational Fluid Dynamics And Experimental Fluid Dynamics For Ground Effect Aerodynamics Studies, Tj Barber, G Doig, C Beves, I Watson, S Diasinos

Aerospace Engineering

This article highlights the ‘synergistic’ use of experimental fluid dynamics (EFD) and computational fluid dynamics (CFD), where the two sets of simulations are performed concurrently and by the same researcher. In particular, examples from the area of ground effect aerodynamics are discussed, where the major facility used was also designed through a combination of CFD and EFD. Three examples are than outlined, to demonstrate the insight that can be obtained from the integration of CFD and EFD studies. The case studies are the study of dimple flow (to enhance aerodynamic performance), the analysis of a Formula-style front wing and wheel, …

Aerodynamics Of An Aerofoil In Transonic Ground Effect: Methods For Blowdown Wind Tunnel Scale Testing, G. Doig, T. J. Barber, A. J. Neely, D. D. Myre

Aerospace Engineering

No abstract provided.

Development Of A Flight Test Program For A Homebuilt Zenith Stol Ch 701, Reed Danis, Dave Nguyen

Aerospace Engineering

The objective of this senior project is to prepare a phase I flight test program for a homebuilt Zenith CH 701 kit aircraft. The CH 701 is a small, short takeoff and landing experimental aircraft. A team including several Cal Poly students helped to construct the airframe and avionics of a 701 during the 2011-2012 academic year. The flight test program is necessary for obtaining unrestricted FAA flight certification for the completed aircraft. A set of test flight cards were created to aid in meeting the 25 to 40 hours of required phase I flight testing. These cards include specific …

De-Orbiting Upper Stage Rocket Bodies Using A Deployable High Altitude Drag Sail, Robert A. Hawkins Jr., Joseph A. Palomares

Aerospace Engineering

This report examines the effectiveness of a drag sail to de-orbit upper stage rocket bodies. Many other perturbations contribute to the de-orbiting of these rocket bodies, and these perturbations will also be discussed briefly. This paper will show the length of time needed to force the altitudes of various launch vehicle stages with varying drag area sizes to less than 100 km. The upper stage of the Delta IV launch vehicle in an orbit with an altitude of 500 km will naturally de-orbit in 720 days but when equipped with a 20 m² drag sail, it will de-orbit in …

A Study On Organic Epoxy And Hemp Composite Plates With An Emphasis On Mechanical And Finite Element Analysis, Alma Melendez

Aerospace Engineering

Several vibration and tensile tests were conducted for four natural fiber hemp composites in order to observe its behavior and acquire the material properties of hemp. Two plates were made on the Cal Poly press table, while the other two plates were made on the Cal Poly vacuum table. All four plates are made of 100% hemp under three different types of weave. The first plate is called CTPT-12, has a thickness of 0.053 inches, and was made on the press table. The second plate is called CTL4 with a thickness of 0.152 inches and made on the press table. …

Ramjet Fuel System, Kelsey Selin

Aerospace Engineering

No abstract provided.

Empennage Sizing And Aircraft Stability Using Matlab, Ryan C. Struett

Aerospace Engineering

No abstract provided.

Degradation Of Solar Cells Due To Arcing In A Vacuum Chamber, Christina Gonzalez

Aerospace Engineering

This report summarizes the senior project entitled Degradation of Solar Cells Due to Arcing in a Vacuum Chamber. The goal of this experiment was to show electrical and physical degradation of silicon solar cells in a vacuum chamber. The cells were characterized and then placed in a vacuum chamber. Under vacuum, a potential was created to induce arcing to the cell. The cell was characterized again after arcing to determine the change in efficiency. This document details the process for designing the circuit to create the arcing, and the different setups used to degrade the cells electrically and physically. It …

The Study Of Natural Composite I-Beam In A Three Point Bending Test, Abdel Shabbar

Aerospace Engineering

The objective of this experiment is to conduct a series of unidirectional tensile test on several samples of natural occurring plant fibers. Among the materials tested, hemp has proven to be the most promising candidate as the base material in creating an all-natural composite I-Beam. This I-Beam will be entered into the annual SAMPE 2012 competition to compete against other schools and universities nationwide. These I-Beams will undergo a three point bending test, and must withstand the greatest load whilst remaining in the parameters set by SAMPE. This I-Beam will go on to take third place internationally. In addition, the …

Flaperon Assembly Manual For Pegastol Aftermarket Wings, Eric Alan Gray

Aerospace Engineering

No abstract provided.

Assembly Of A Passive Slat System For A Ch-701 Kit Aircraft, Jordan Coenen, Spencer Spagnola

Aerospace Engineering

No abstract provided.

Computation Time Comparison Between Matlab And C++ Using Launch Windows, Tyler Andrews

Aerospace Engineering

Processing speed between Matlab and C++ was compared by examining launch windows and handling large amounts of data found in pork chop plots. A compilation of code was generated in Matlab to produce the plots and an identical file was created in C++ that was then compiled and run in Matlab to plot the data. This file is known as a MEX-file. This report outlines some of the basics when working with MEX-files and the problems that face users. For Lambert’s solver, multi revolution cases were considered and some pork chop plots of single revolution trajectories were plotted. Three different …

Preliminary Design Of A Laboratory Cylindrical Hall-Effect Thruster, Scott Mcgrail, Sam Parker

Aerospace Engineering

A 3-cm cylindrical Hall thruster with permanent magnets was designed and modeled. The goal was to design a Hall thruster for Cal Poly’s propulsion laboratory of similar size and performance as Cal Poly’s MiXI thruster. The design process began with an investigation into the physics of Hall thrusters and selection of certain thruster parameters. The selected parameters were the diameter and depth of the channel, the total power input to the system, the discharge supply voltage, the cathode voltage, and the propellant flow rates to the anode and cathode. These parameters were used to determine the operational characteristics of the …

Data Acquisition For Flight Tests Using Handheld Gps And Electronic Flight Instrument System, Christopher Michael Gocha

Aerospace Engineering

No abstract provided.

Reliable Software Updates For On-Orbit Cubesat Satellites, Sean Fitzsimmons

Master's Theses

CubeSat satellites have redefined the standard solution for conducting missions in space due to their unique form factor and cost. The harsh environment of space necessitates examining features that improve satellite robustness and ultimately extend lifetime, which is typical and vital for mission success. The CubeSat development team at Cal Poly, PolySat, has recently redefined its standard avionics platform to support more complex mission capabilities with this robustness in mind. A significant addition was the integration of the Linux operating system, which provides the flexibility to develop much more elaborate protection mechanisms within software, such as support for remote on-orbit …

Design Of A Human Powered Helicopter Airframe, Sheen Kao, Daniel Layton, Philip Sobol

Mechanical Engineering

In 1989 Cal Poly’s Da Vinci III was the first human powered helicopter (HPH) to achieve flight; our goal is to research and develop a new airframe for the next generation Da Vinci. This report outlines a brief history of human powered flight and details a method of constructing for the airframe. An optimized airframe geometry was also researched and is explained in detail.

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Aerodynamic Test Platform For Human Powered Vehicle (Hpv), Spencer Wangerin, Spencer Lillywhite, Colburn Davis

Mechanical Engineering

The Aerodynamic Test Platform (ATP) for the Cal Poly HPV Club is a system that was designed by Cal Poly mechanical engineering students to measure aerodynamic characteristics of a human-powered vehicle (HPV). The HPV team desired a system that could quantify the lift, drag, and other aerodynamic qualities of a full scale HPV at various orientations in oncoming airflow. Established methods for determining aerodynamic characteristics include computational fluid dynamics (CFD) and wind tunnel testing of scaled models. The ATP was devised to simulate the test results given by a full-scale wind tunnel without requiring a wind tunnel large enough to …

Development Of A Ground Based Atomic Oxygen And Vacuum Ultraviolet Radiation Simulation Apparatus, Max Jay Glicklin

Master's Theses

The space environment possesses numerous unique and unusual attributes, creating challenges that must be considered in order to accomplish a successful space mission. Two of the detrimental aspects of the space environment include Atomic Oxygen, AO, and Ultraviolet, UV, radiation. UV radiation becomes more severe in space as there is no atmosphere to attenuate incoming photons, thereby exposing spacecraft to radiation that never reaches the surface of the Earth. Overall, space vehicles are exposed to a total of 107.4 Watts/m² of light shorter than 400 nm. AO is created by the photo disassociation of molecular oxygen by UV radiation …

Registering An Amateur-Built Light Sport Kit Aircraft, Kevin Condron

Aerospace Engineering

No abstract provided.

Flying Qualities Built-In-Test For Unmanned Aerial Systems, Alton Pak-Hin Chiu

Master's Theses

This paper presents a flying qualities built-in-test for UAS application with the scope limited to the longitudinal axis. A doublet input waveform excites the AV and both α and q are used by EUDKF to estimate the A and B matrices which are short period approximations of the system. ζ, ω, GM, PM, observability, and controllability are calculated to determine flying qualities with the results displayed to the AVO in a color-coded, easy to interpret display.

While SID algorithms have been flying in vehicles with adaptive control schemes, vehicles with other schemes (such as classical feedback) lack this built-in self …

Activity Node Based Flight Software As A Benefit To Systems Engineering, Eugene Daniel Lewis

Master's Theses

This report discusses one application of a flight software design for a spacecraft in which the software executes from a database that can be managed by systems engineering. This report gives an overview of how such a software design can be developed and implemented. It also discusses why this approach is beneficial to the systems engineering program.

Cubesat Mission Planning Toolbox, Brian Castello

Master's Theses

We are in an era of massive spending cuts in educational institutions, aerospace companies and governmental entities. Educational institutions are pursuing more training for less money, aerospace companies are reducing the cost of gaining ight heritage and the government is cutting budgets and their response times. Organizations are accomplishing this improved efficiency by moving away from large-scale satellite projects and developing pico and nanosatellites following the CubeSat specifications. One of the major challenges of developing satellites to the standard CubeSat mission requirements is meeting the exceedingly tight power, data and communication constraints.

A MATLAB toolbox was created to assist the …

Feasibility Study Into The Use Of 3d Printed Materials In Cubesat Flight Missions, Daniel Fluitt

Master's Theses

The CubeSat Program has provided access to space for many universities, private companies, and government institutions primarily due to the low cost of CubeSat satellite development. While these costs are orders of magnitude lower than similarly capable nano-satellite missions, they are still outside of the budgetary constraints of many potential developers including university and high school clubs. Using 3D printed plastics in the production of CubeSat structures and mechanisms presents a large cost savings opportunity that will allow these institutions to participate in the development of these satellites, expanding the educational and scientific impact of the CubeSat Program.

Five rapid …

Implementation Of A ¼ Inch Hollow Cathode Into A Miniature Xenon Ion Thruster (Mixi), David Wayne Knapp

Master's Theses

Over the last decade, miniature ion thruster development has remained an active area of research do to its low power, low thrust, and high efficiency, however, due to several technical issues; a flight level miniature ion thruster has proved elusive. This thesis covers the design, fabrication, assembly, and test of an altered version of the Miniature Xenon Ion thruster (MiXI), originally developed by lead engineer Dr. Richard Wirz, at the California Institute of Technology (Caltech). In collaboration with Dr. Wirz, MiXI-CP-V3 was developed at Cal Poly San Luis Obispo with the goal of implementing of a ¼ inch hollow cathode …

An Investigation Of Damage Arrestment Devices On Carbon Fiber Sandwich Specimens Under Dynamic Loading, Gabriel Sabino Sanchez

Master's Theses

This research studies the effects of a damage arrestment device embedded between a carbon fiber facesheet and foam core to find whether there is an increase in the structural integrity of the sandwich composites. Experimental and theoretical finite element analyses are implemented for two different composite sandwich geometries; plates and beams. Each structure consisted of the same loading criteria and was restricted to the same vibration fixture during the experiment. An accelerometer was placed on the composite plate to record the amplitude and the natural frequencies of the composite structure. Each composite specimen is then fixed to the surface of …

Hapss, Hybrid Aircraft Propulsion System Synthesis, Michael W. Green

Master's Theses

Hybrid Aircraft Propulsion System Synthesis (HAPSS) is a computer program that sizes and analyzes pure-series hybrid electric propulsion systems for aircraft. The development of this program began during a NASA SBIR contract, in conjunction with Empirical Systems Aerospace (ESAero), with the creation of a propulsion fan design tool. Since the completion of this contract in July 2010, the HAPSS program has been expanded to combine the many aspects of a hybrid propulsion system such as the propulsive fans, electric motors, generators, and controllers, and the internal combustion engines.

This thesis describes the benefits and drawbacks of aircraft hybrid propulsion systems …