Engineering Commons^™

Fabrication Of Smooth Sac305 Thin Films Via Magnetron Sputtering And Evaluations Of Microstructure, Creep, And Electrical Resistivity, Manish Ojha

Mechanical & Aerospace Engineering Theses & Dissertations

SAC305 (96.5%Sn-3%Ag-0.5%Cu) is the leading alternative to the traditional Sn-Pb solder eutectic alloy owing to its low melting temperature, better compatibility with other components, and excellent mechanical/structural properties. In the realm of modern electronics, where devices are increasingly miniaturized, the design and characterization of thin solder joints become paramount. The orientation and size of the grains within the solder can influence its ability to withstand mechanical stresses. However, research on SAC thin films remains sparse, and these films present unique challenges and characteristics compared to their bulk counterparts, influenced by factors like interfaces, stresses, thickness, microstructure, and the nature of …

The Effect Of Through Thickness Reinforcement Angle On The Disbonding Behavior In Skin-Stringer Configuration, Christopher John Morris

Mechanical & Aerospace Engineering Theses & Dissertations

Post-cure through thickness reinforcement is a method used to increase the mechanical properties of composite laminates in the transverse direction. This study conducted a test on skin-stringer structures bonded together in three configurations using an epoxy or thermoplastic adhesive at the interface with reinforcing pins inserted through the laminate thickness located at the edge of the stringer at differing angles between -30º and 30º. The fabrication of these samples in configurations B and C consisted of the use of carbon fiber prepeg laminate at a ply orientation of [0₂90₂]_2s for the skin and [0 90] …

An Effective Model For Dynamic Properties Of Local Soils And Their Influence On Seismic Response Of A Typical Reinforced Concrete Building, Kaveh Zehtab

Civil & Environmental Engineering Theses & Dissertations

This dissertation presents an effective model to determine the dynamic properties of local soils and their impact on the seismic response of a typical mid-height reinforced concrete building. The results of the study suggest that the use of global models and empirical relationships for the dynamic properties of soils may not consider the effects of unique stress conditions on the cyclic response of the foundation soil. The study also investigates the seismic response of a site in central Adapazarı, Turkey, where four- to seven-story buildings suffered significant damage during the 1999 Kocaeli earthquake. A new model is presented that combines …

Faster, Cheaper, And Better Cfd: A Case For Machine Learning To Augment Reynolds-Averaged Navier-Stokes, John Peter Romano Ii

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, the field of machine learning (ML) has made significant advances, particularly through applying deep learning (DL) algorithms and artificial intelligence (AI). The literature shows several ways that ML may enhance the power of computational fluid dynamics (CFD) to improve its solution accuracy, reduce the needed computational resources and reduce overall simulation cost. ML techniques have also expanded the understanding of underlying flow physics and improved data capture from experimental fluid dynamics.

This dissertation presents an in-depth literature review and discusses ways the field of fluid dynamics has leveraged ML modeling to date. The author selects and describes …

Studies Of Flowfields And Dynamic Stability Characteristics Of A Quadrotor, Engin Baris

Mechanical & Aerospace Engineering Theses & Dissertations

Electric multirotor air vehicles have become a pervasive technology and research topic in industry, academia, and daily life, and small quadrotors are one of the most preferred designs in the multirotor marketplace. However, the configuration of the quadrotors makes aerodynamic interaction effects one of the key factors of the vehicle performance in both hover and non-axial forward flight conditions.

In the present work, aerodynamic characteristics of the cross-configured small quadrotor in hover, edgewise, and maneuvering flight modes were investigated in detail by performing static and dynamic wind tunnel tests at various RPM levels, wind speeds, pitch and yaw angles, and …

Framing Automation Trust: How Initial Information About Automated Driving Systems Influences Swift Trust In Automation And Trust Repair For Human Automation Collaboration, Scott Anthony Mishler

Psychology Theses & Dissertations

The study examines how trust in automation is influenced by initial framing of information before interaction and how later active calibration methods can further influence trust repair or dampening after an automation error in a three-experiment study. As more human drivers begin to use automated driving systems (ADSs) for the first time, their initial understanding of the system can influence their trust leading to a miscalibration of trust. Prior studies have investigated how trust develops through interactions with an automated system, but few have looked at integrating swift trust and framing to calibrate trust before interaction and investigate further active …

Framework For Implementing Advanced Radar Plotting Aid Capability For Small Maritime Vessels, Jason Stark Harris

Electrical & Computer Engineering Theses & Dissertations

Every year in the United States many people are killed or injured when maritime vessels collide with other vessels or fixed objects. According to the United States Coast Guard, the top contributing factors to these collisions are operator inattention, operator inexperience and an improper lookout. Larger commercial vessels are required to have RADAR systems which support Automatic RADAR Plotting Aid (ARPA) which can automatically detect collisions and alert an operator to change course. These systems can be very expensive which put them out of reach of the average recreational boater. It is however possible to implement a low cost ARPA …

Pulsed Electric Field Ablation: Mechanisms Of Differential Cell Sensitivity And Methods To Mitigate Neuromuscular Excitation, Emily Gudvangen

Biomedical Engineering Theses & Dissertations

Ablation therapies aim to destroy tumors while maintaining minimal damage to surrounding healthy tissue. Pulsed electric field (PEF) ablation targets the cell membrane during the destruction of tissues, which consequently spares extracellular structures such as ducts and blood vessels, leaving the framework for tissue regeneration. However, the utility of PEF is limited by neuromuscular excitation, causing pain and involuntary muscle contraction. To identify PEF protocols that efficiently ablate tissue while minimizing neuromuscular stimulation, various PEF protocols differing in pulse duration, shape, and repetition rate were tested. The ratio of cell death and nerve excitation thresholds, which determines the range of …

Switching Methods For Three-Dimensional Rotational Dynamics Using Modified Rodrigues Parameters, Matthew Jarrett Banks

Mechanical & Aerospace Engineering Theses & Dissertations

A rigid body in space has three degrees of rotational freedom. As a result, a minimum of three independent parameters is required to define the three-dimensional orientation of a rigid body. As is well known, every set of three independent parameters has at least one orientation where mathematical or geometrical singularities are encountered; therefore, when the use of a three-parameter representation is desired, a method for singularity avoidance must also be considered. A common practice for singularity avoidance is to switch between parameter sets whose singularities occur at different orientations. With this in mind, modified Rodrigues parameters (MRP) are considered …

Investigation Of Nanosecond Pulsed Electric Fields (Nspef) Induced Anti-Cancer Mechanism And Enhanced B16f10 Melanoma Cancer Treatment, Kamal Asadipour

Biomedical Engineering Theses & Dissertations

The use of nanosecond pulsed electric fields (nsPEF) has emerged as a promising area of research with vast implications across various scientific disciplines. The ability to generate ultra-short, high-voltage electric pulses has paved the way for numerous applications, ranging from fundamental investigations of biological phenomena to the development of innovative medical therapies. The aim of this thesis is to highlight the importance of nsPEF in two critical areas: 1) Understanding the impact of subtle postpulse waveforms through a comprehensive analysis of two common pulse generators and 2) using this knowledge to advance melanoma treatment by enhancing the therapeutic effect of …

Lithium Extraction From Aqueous Solution Using Magnesium Doped Lithium Ion-Sieve Composite, Ujjwal Pokharel

Civil & Environmental Engineering Theses & Dissertations

This study focused on the development of a magnesium doped ion-sieve composite to extract lithium from an aqueous solution using adsorption process. The extraction process will provide a sustainable alternative to the currently practiced solar evaporation/concentration method which is very slow (takes 24 months) and water intensive. Currently, most of the lithium in the world comes from the mining of lithium or from the evaporative extraction process from the brine. Additionally, the Salton Sea area geothermal brines are recognized as potentially important domestic sources of lithium. Lithium concentration in geothermal brines from the Salton Sea area is reported to be …

Optics Studies For Multipass Energy Recovery At Cebaf: Er@Cebaf, Isurumali Neththikumara

Physics Theses & Dissertations

Energy recovery linacs (ERLs), focus on recycling the kinetic energy of electron beam for the purpose of accelerating a newly injected beam within the same accelerating structure. The rising developments in the super conducting radio frequency technology, ERL technology has achieved several noteworthy milestones over the past few decades. In year 2003, Jefferson Lab has successfully demonstrated a single pass energy recovery at the CEBAF accelerator. Furthermore, they conducted successful experiments with IR-FEL demo and upgrades, as well as the UV FEL driver. This multi-pass, multi-GeV range energy recovery demonstration proposed to be carried out at CEBAF accelerator at Jefferson …

Open-Cast Mining Deformations Monitoring Using Sentinel-1 Sar Data (Sbas Technique), Mahvash Naddaf Sangani, Seyed Reza Hosseinzadeh, José Francisco Martín Duque, Mahnaz Jahadi Toroghi, Kapil Kumar Malik

Journal of Sustainable Mining

Land surface deformation created by mining activities can have negative impacts on the environment. Measuring them can be a tool for managing the environmental impacts of mining. Synthetic Aperture Radar Interferometry is a remote sensing method for measuring deformations. The main aim of this research is to investigate the deformation phenomenon on a region scale and extend our understanding of it to all mining deformation areas across the country. This paper used Small Baseline Subset Interferometric Synthetic Aperture Radar technology to obtain deformations information in the Sangan mine based on mining activities. We used 48 scenes of Single Look Complex(SLC) …

Numerical Modelling Of Uniaxial Compressive Strength Laboratory Tests, Phu Minh Vuong Nguyen, Andrzej Walentek, Petr Waclawik, Kamil Soucek, Michał Antoniuk

Journal of Sustainable Mining

In the last decades, numerical modelling has been widely used to simulate rock mass behaviour in geo-engineering issues. The only disadvantage of numerical modelling is the reliability of required input data (e.g. mechanical parameters), which is not always fully provided due to the complexity of rock mass, project budget, available test methods or human errors. On the other hand, it was proven in many cases that numerical modelling is a helpful tool for solving such complex problems, especially when coupled with the results of laboratory and in-situ tests. This paper presents an attempt to determine the proper numerical constitutive model …

Semi-Annual Progress Report #12, Missouri University Of Science And Technology. Inspire - University Transportation Center

Semi-Annual Progress Reports

No abstract provided.

Enhanced Cell Viability And Migration Of Primary Bovine Annular Fibrosus Fibroblast-Like Cells Induced By Microsecond Pulsed Electric Field Exposure, Prince M. Atsu, Connor Mowen, Gary L. Thompson Iii

Henry M. Rowan College of Engineering Departmental Research

This study is the first to report the enhancement of cell migration and proliferation induced by in vitro microsecond pulsed electric field (μsPEF) exposure of primary bovine annulus fibrosus (AF) fibroblast-like cells. AF primary cells isolated from fresh bovine intervertebral disks (IVDs) are exposed to 10 and 100 μsPEFs with different numbers of pulses and applied electric field strengths. The results indicate that 10 μs-duration pulses induce reversible electroporation, while 100 μs pulses induce irreversible electroporation of the cells. Additionally, μsPEF exposure increased AF cell proliferation up to 150% while increasing the average migration speed by 0.08 μm/min over 24 …

Stress-Dependent Petrophysical Properties Of The Bakken Unconventional Petroleum System: Insights From Elastic Wave Velocities And Permeability Measurements, Prasad Pothana, Ghoulem Ifrene, Kegang Ling

Petroleum Engineering Student Publications

The net-effective stress is a fundamental physical property that undergoes dynamic changes in response to variations in pore pressure during production and injection activities. Petrophysical properties, including porosity, permeability, and wave velocities, play a critical role and exhibit strong dependence on the mechanical stress state of the formation. The Williston basin’s Bakken Formation represents a significant reservoir of hydrocarbons within the United States. To investigate this formation, we extracted core plugs from three distinct Bakken members, namely Upper Bakken, Middle Bakken, and Lower Bakken. Subsequently, we conducted a series of measurements of ultrasonic compressional and shear wave velocities, as well …

Retraining Investment For Alberta’S Oil And Gas Workers For Green Jobs In The Solar Industry, Theresa K. Meyer, Carol Hunsberger, Joshua M. Pearce

Michigan Tech Publications

If oil sands are to be eliminated from the energy market to protect the global environment, human health and long-term economic welfare, a significant number of workers will be displaced in the transition to renewable energy technologies. This study outlines a cost-effective and convenient path for oil and gas workers in Alberta to be retrained in the burgeoning solar photovoltaic (PV) industry. Many oil and gas workers would be able to transfer fields with no additional training required. This study examines retraining options for the remainder of workers using the most closely matching skill equivalent PV job to minimize retraining …

Assessment Of Spatial Variability Of Groundwater Potential Using Remote Sensing And Gis-Based-Criteria Evaluation For Dar Es Salaam, Tanzania, Augustina Alexander

Tanzania Journal of Engineering and Technology (TJET)

Groundwater is an important resource for the continuous provision of water supply in both urban and rural areas. Lack of enough knowledge about the spatial variability of groundwater potential zones (GWPZS) has a negative impact on groundwater extraction development and management and may result into over exploitation. In this study, analytic hierarchy approach (AHP)-coupled with multi criteria decision analysis (MCDA) and GIS techniques were employed to integrate hydrogeological, geological as well as topographical data to assess spatial variability of groundwater potential zones of Dar es Salaam city. Seven thematic layers such as lithology, slope, land-use, lineament, drainage, soil, and rainfall …

Designing A Model Of Solar Photovoltaic Water Pumping System For Off-Grid Localities In Tanzania, Imani Mruma

Tanzania Journal of Engineering and Technology (TJET)

Modeling of photovoltaic (PV) water pumping system for rural water localities is vital especially in these modern days, in Tanzania. This is due to the rise of high number of solar-powered rural water projects constructed lacking appropriate design. The fate result into poor and substandard projects delivering below expectations. Kikombo Solar Water Project situated in Dodoma; Tanzania is one among poorly designed solar project chosen as a case study to validate proposed model. The main problem of Kikombo project is unsatisfactory amount of water from domestic points to satisfy population demand. This matter has been raised by pumping-station attendants and …

Extraction And Characterization Of Fibres From The Bark Of Ficus Nekbudu Tree, Liberato V Haule

Tanzania Journal of Engineering and Technology (TJET)

This paper investigates the extraction and characterization of fibres from the bark of the ficus nekbudu tree. The Ficus Nekbudu Fibres (FNF) was extracted from the bark by retting in water and then treatment with sodium hydroxide solution. The extracted FNF was analysed for chemical composition, physical, tensile, surface, structural and thermal stability properties. Findings on the chemical composition indicated that FNF has cellulose (49.9 %), lignin (13.4%), ash (7.1%) and water content (8.1%). From the physical investigation it was found that FNF has density (1.42 ± 0.005 g/cm3) and moisture regain (9.2 ±0.3%). From mechanical investigation it was found …

Designing A Cylindrical Capacitive Based Sensor For Monitoring The Table Salt’S Moisture Content During Iodization, Mwajuma Lungo

Tanzania Journal of Engineering and Technology (TJET)

Coaxial cylinder capacitive moisture sensor for determination of moisture content of table salts has been fabricated. The CMS method for determination of moisture content of table salts overcomes the effect of evaporation of iodine in table salt which results from heating in the oven drying method. The CMS overcomes the polarization effect result from the resistive methods of moisture content determination and it is non expensive to construct and it has high accuracy since measurements involves programming system in interpretation of the results. In this research, moisture content sensor based on capacitive principal created using two coaxial cylinders with height …

Comparison Of End-Point Energies Of Bremsstrahlung Photons From 28 Ghz Ecr Ion Source In Three Measurement Locations, Mwingereza John Kumwenda Dr

Tanzania Journal of Engineering and Technology (TJET)

Bremsstrahlung photons measurement show elevated energy emission beyond critical energy in 28-GHz ECR and its nature is not revealed. Thus, the aim of this study is to unveil the nature of high end-point energies at the three measurement locations. Bremsstrahlung photons from a 28-GHz ECR ion source were measured at Busan center of Korean Basic Science Institute (KBSI). The gamma-ray detection system consists of three round type NaI(Tl) scintillation detectors placed 62 cm radially from the beam axis at the three measurement locations namely injection, centre and extraction sides of an ECR ion source, and a NaI(Tl) scintillation detector placed …

Renewable Energy Potential Assessment For Improving Electric Power Availability In Urban Area: A Case Of Msigani Ward In Ubungo Municipal, Tanzania, Respicius Kiiza

Tanzania Journal of Engineering and Technology (TJET)

The demand for electricity in urban areas of the developing countries like Tanzania is increasing rapidly due to factors such as increasing population, expansion of economic activities and industrialization. Msigani ward is one of the fourteen (14) administrative urban wards in Ubungo Municipal, Dar es Salaam, located at latitude 6.8031 oS and longitude 39.1188 oE. Recently, there has been observed increase in power demand in this ward. This in turn has caused a supply deficit that sometimes led to large number of interruptions caused by frequent power outage and load shedding. The total capacity of the national grid is limited …

Mppt Dc-Dc Buck-Boost Converter For Off Grid Hybrid Solar-Wind Battery System In Ikuza Island, Tanzania, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

Ikuza Island in Kagera-Tanzania faces lack of electricity due to cost challenges of extending the grid by marine cables and other transmission facilities. These makes such endeavour not appealing to the supply authority due to those higher charges. Therefore, this paper undertakes to design hybrid renewable energy sources for the island by specifically focusing on the buck-boost converter for the energy conversion from these renewable resources. The design of the bidirectional buck-boost converter for maximum power point tracking in off-grid hybrid renewable energy systems is multifaceted due to the inhomogeneity nature of the renewable energy sources. The bidirectional buck-boost converter, …

Assessing Spatio-Temporal Variations And Trends Of Rainfall Over Somalia From 1991 To 2020, Paul Ts Limbu Sr

Tanzania Journal of Engineering and Technology (TJET)

This study aims to examine the spatiotemporal variability and trends of rainfall over Somalia using the Mann-Kendall (MK) test and Sen’s slope estimator to investigate the trend and magnitude of the rainfall changes and the arithmetic mean and coefficient of variation (CV) to examine the rainfall variability. To achieve this aim, the gridded monthly satellite rainfall datasets from Climate Hazards Group InfraRed Precipitation with Station (CHIRPS) for the period between 1991 and 2020 were used. Results show that annual rainfall generally exhibits bimodal rainfall distribution, March to May (Gu) and September to November (Deyr), though southern coastal regions receive extended …

Enhancing Service Restoration In Tanzanian Power Grid Using Internet Of Things Sensors And Renewable Energy Sources, Rukia J. Mwifunyi, Daudi C. Mnyanghwalo, Shamte J. Kawambwa

Tanzania Journal of Science

The increased dependence on the electric power grid, coupled with the increasing number of new customers, motivates the need to improve the reliability and resilience of the electric distribution systems. Modern distribution systems are becoming more resilient against power outages due to the increasing integration of Distributed Energy Resources (DERs) and the availability of efficient mechanisms for load shedding. Several studies considered fault detection and Service Restoration (SR) as separate problems without considering the implementation feasibility of integrating both solutions. To ensure the resiliency in the power system, it is important to have proper mechanisms which integrate sensing, detection, and …

Aquaculture In Hydropower Reservoirs, Racheal Macharia

Tanzania Journal of Engineering and Technology (TJET)

There is an undoubtedly existing relationship between water, energy, and food and their interaction with the natural environment and mankind. Climate change is the talk of the day in global development discussions as it intensifies water shortages, energy, poverty, food shortages, and environmental degradation. Currently, most of the hydropower dams constructed in Africa are majorly built to store water for agricultural purposes, control flooding, and generate electricity. Notable projects include the seven forks hydropower stations located on the Tana River in Kenya; Aswan high dam in Egypt; Grand Renaissance dam in Ethiopia; Kariba dam in Zimbabwe and Akosombo in Ghana. …

Application Of Mangrove Timber In Reinforcing Concrete, John K. Makunza Jkm

Tanzania Journal of Engineering and Technology (TJET)

Use of mangrove timber beams for supporting floor slabs in historic buildings in Zanzibar Stone Town is still applied although the available structural data on mangrove timber is inadequate. This concern has called for an investigation on the structural properties of mangrove timber, so that the information obtained could help to establish the structural strength of the existing floor slabs in historic buildings. Hence, mangrove timber specimens were sampled from Zanzibar, and tested in the laboratory for their strengths in tension, compression and shear. The test results showed that mangrove is a hardwood timber of strength class D70, the highest …

A Multitask Learning Framework For Pilot Decontamination In 5g Massive Mimo, Crallet Victor

Tanzania Journal of Engineering and Technology (TJET)

Reference signals enable the acquisition of channel state information (CSI) for purposes such as channel estimation, beam selection, precoding, and symbol detection in 5G massive multiple-input multiple output (MAMIMO) systems. Eventually, as more and more users and cells are added, orthogonal reference signals become few which leads to pilot contamination. Pilot contamination limits the performance and occurs when non-orthogonal reference signals occupy time-frequency resources that are alike. Learning-based techniques have been proposed to alleviate it. However, each can only learn to perform a single task namely pilot assignment, power allocation, pilot design, or de-noising for pilot decontamination. In addition, each …