Engineering Commons^™

A Comparative Analysis Of Energy Modelingmethods For Commercial Buildings, Spencer Mark Salmon

Theses and Dissertations

This thesis researched the accuracy of measured energy data in comparison to estimated hand calculation data and estimated building energy performance simulation data. In the facility management industry, there is minimal evidence that building energy performance software is being used as a benchmark against measured energy usage within a building. Research was conducted to find examples of measured energy data compared to simulated data. The study examined the accuracy of a simulation software and hand calculations to measured energy data. Data suggests that comparisons may be made between building energy performance simulated data and measured data, though comparisons are solely …

Silicon Quantum Electronics, Floris A. Zwanenburg, Andrew S. Dzurak, Andrea Morello, Michelle Y. Simmons, Lloyd C. L. Hollenberg, Gerhard Klimeck, Sven Rogge, Susan N. Coppersmith, Mark A. Eriksson

Birck and NCN Publications

This review describes recent groundbreaking results in Si, Si/SiGe, and dopant-based quantum dots, and it highlights the remarkable advances in Si-based quantum physics that have occurred in the past few years. This progress has been possible thanks to materials development of Si quantum devices, and the physical understanding of quantum effects in silicon. Recent critical steps include the isolation of single electrons, the observation of spin blockade, and single-shot readout of individual electron spins in both dopants and gated quantum dots in Si. Each of these results has come with physics that was not anticipated from previous work in other …

Pilot Study Assessment Of Dynamic Vascular Changes In Breast Cancer With Near-Infrared Tomography From Prospectively Targeted Manipulations Of Inspired End-Tidal Partial Pressure Of Oxygen And Carbon Dioxide, Shudong Jiang, Brian W. Pogue, Kelly E. Michaelsen, Michael Jermyn, Michael A. Mastanduno, Tracy E. Frazee, Peter A. Kaufman, Keith D. Paulsen

Dartmouth Scholarship

The dynamic vascular changes in the breast resulting from manipulation of both inspired end-tidal partial pressure of oxygen and carbon dioxide were imaged using a 30 s per frame frequency-domain near-infrared spectral (NIRS) tomography system. By analyzing the images from five subjects with asymptomatic mammography under different inspired gas stimulation sequences, the mixture that maximized tissue vascular and oxygenation changes was established. These results indicate maximum changes in deoxy-hemoglobin, oxygen saturation, and total hemoglobin of 21, 9, and 3%, respectively. Using this inspired gas manipulation sequence, an individual case study of a subject with locally advanced breast cancer undergoing neoadjuvant …

Unveiling The Roles Of Binder In The Mechanical Integrity Of Electrodes For Lithium-Ion Batteries, Jianchao Chen, Jianyong Liu, Yue Qi, Tao Sun, Xiaodong Li

Faculty Publications

In lithium-ion secondary batteries research, binders have received the least attention, although the electrochemical performance of Li-ion batteries such as specific capacity and cycle life cannot be achieved if the adhesion strengths between electrode particles and between electrode films and current collectors are insufficient to endure charge-discharge cycling. In this paper, the roles of binders in the mechanical integrity of electrodes for lithium-ion batteries were studied by coupled microscratch and digital image correlation (DIC) techniques. A microscratch based composite model was developed to decouple the carbon particle/particle cohesion strength from the electrode-film/copper-current-collector adhesion strength. The dependences of microscratch coefficient of …

Improvements In Diffusion Weighted Imaging Through A Composite Body And Insert Gradient Coil System, Peter Austin Jepsen

Theses and Dissertations

Diffusion Magnetic Resonance Imaging (DMRI) is a class of Magnetic Resonance Imaging (MRI) techniques with broad medical applications ranging from characterization of tumors and brain damage to potential prediction of stroke. Gradient coil and signal-to- noise ratio (SNR) constraints limit spatial resolution, accuracy, and scan time in DMRI. Achieving high b-values (measures of a scan's sensitivity to diffusion) often require scans with long diffusion gradient pulses, leading to significant magnetic resonance (MR) signal decay before the signal can be sampled. This signal loss reduces the accuracy of diffusion parameter estimation. The ability to sample the MR signal sooner while maintaining …

Gesture Analysis For Human-Computer Interface Using Profile-Matching Stereo Vision, Yung Ping Chang

Theses and Dissertations

This thesis presents a novel profile shape matching stereo vision algorithm. This algorithm is able to obtain 3D information in real time from a pair of stereo images. This algorithm produces the 3D information by matching the profile intensity shapes on the same row of the two images from a stereo image pair. The advantage of this profile shape matching algorithm is that the detection of correspondences relies on intensity profile shape not on intensity values, which subject to lighting variations. The user can choose an interval of disparity, and then an object in a desired distance range can be …

Variable Fidelity Optimization With Hardware-In-The-Loop For Flapping Flight, Michael Luke Duffield

Theses and Dissertations

Hardware-in-the-loop (HIL) modeling is a powerful way of modeling complicated systems. However, some hardware is expensive to use in terms of time or mechanical wear. In cases like these, optimizing using the hardware can be prohibitively expensive because of the number of calls to the hardware that are needed. Variable fidelity optimization can help overcome these problems. Variable fidelity optimization uses less expensive surrogates to optimize an expensive system while calling it fewer times. The surrogates are usually created from performing a design of experiments on the expensive model and fitting a surface to the results. However, some systems are …

Modeling And Optimization Of Space Use And Transportation For A 3d Walkable City, Bradley R. Mecham

Theses and Dissertations

This thesis presents an investigation of a new three-dimensional urban form where walking distances are less than a half-mile and congestion is minimal. The car-free urban form investigated herein is a city composed of skyscrapers massively interconnected with skybridges at multiple levels. The investigation consists of optimizing space use arrangement, skybridge presence or absence, and elevator number to simultaneously minimize total travel time, skybridge light blockage, and elevator energy usage in the city. These objectives are evaluated using three objective functions, the most significant of which involves a three-dimensional, pedestrian-only, three-step version of the traditional four-step planning model. Optimal and …

The Sustainability Of Lean Manufacturing As A Competitive Advantage, Louis G. Jones

Theses and Dissertations

Since the early 1990s lean manufacturing has been employed by companies looking to reduce costs, increase efficiencies and improve quality. Academic studies of the financial benefits of lean manufacturing are mixed in their results, where some show benefit and others do not. The objective of the current work was to confirm a financial benefit of lean manufacturing, while also establishing whether such a financial advantage was sustainable. Financial data was collected for a large number of companies in the manufacturing sector, over the period from 1990 to 2010. The data were used to show correlation between inventory turns and return …

Large-Scale Testing Of Passive Force Behavior For Skewed Abutments With High Width-Height Ratios, Katie Noel Palmer

Theses and Dissertations

The effects of seismic forces and thermal expansion on bridge performance necessitate an accurate understanding of the relationship between passive force and backwall deflection. In past case studies, skewed bridges exhibited significantly more damage than non-skewed bridges. These findings prompted studies involving numerical modeling, lab-scale tests, and large-scale tests that each showed a dramatic reduction in passive force with increased skew. Using these results, a correlation was developed between peak passive force and backwall skew angle. The majority of these tests had length to height ratios of 2.0; however, for several abutments in the field, the length to height ratio …

Method And Apparatus For Characterizing Microscale Formability Of Thin Sheet Materials, Nasr A. Shuaib, Marwan K. Khraisheh

Mechanical Engineering Faculty Patents

A method of predicting sheet formability at a microscale level includes the steps of providing a grid pattern on a test sheet, bulging the test sheet to a hemispherical shape until a crack is initiated on the surface of the test sheet, detecting the initiation of the crack, acquiring two images of the surface adjacent to the crack and calculating surface strains on the test sheet.

The Use Of Co-Culturing In Solid Substrate Cultivation And Possible Solutions To Scientific Challenges, Wanying Yao, Sue E. Nokes

Biosystems and Agricultural Engineering Faculty Publications

This perspective systematically summarizes the use of solid substrate co‐cultures in agriculture, food, plant, and industrial biotechnology applications. The summarization is organized by organism, i.e. fungus, bacteria, yeast and then co‐cultivation of either two or three organisms. Generally, in solid substrate co‐culture, the organisms synergistically penetrate and degrade the solid substrate, thereby increasing product yield and productivity over a monoculture. Efforts to increase co‐culture performance include optimizing process parameters (pH, temperature, moisture, and oxygen demand) and defining the acceptable types of substrate. Scientific challenges exist in understanding the interactions between microbial stains, such as viability, suite of products, and bio‐transformations. …

An Analysis Of The Provo River Decree And Its Current Application To Provo Area Water Rights, Karsten Eugene Busby

Theses and Dissertations

Water scarcity in the west has created a long history of conflict. When Utah was settled, laws were instituted (both officially and otherwise) that allowed water users to use streams and springs in efficient ways without causing harm to other users. The Provo River Decree is a physical example of local water law that has been in place for almost a hundred years. While many changes have arisen in its area of jurisdiction, it is still drawn upon to determine water rights. Ambiguity, rigidity, and overall changes to use patterns have limited the application of the decree to present situations. …

Quest For Organic Plasmonics, Lei Gu, J. Livenere, G. Zhu, Evgenii E. Narimanov, M. A. Noginov

Birck and NCN Publications

Many photonic metamaterials and plasmonic devices, in spite of their unparalleled responses to light waves and nearly fantastic applications, suffer from absorption loss in constituent metallic components. Unfortunately, none of the known techniques aimed to conquer the absorption loss has led to a revolutionary technological breakthrough, prompting a continuing quest for efficient solutions to the loss problem. In this letter, we study optical properties of non-metallic organic plasmonic and epsilon-near-zero materials and demonstrate propagation of a surface plasmon polariton at the interface between solid organic dye and air. (C) 2013 AIP Publishing LLC.

More Effective Human Spaceflight Programs And Their International Security Implications, Bert Chapman, Sarag J. Saikia

Libraries Faculty and Staff Scholarship and Research

NASA can more effectively perform its missions by transferring its aeronautic responsibilities to the Federal Aviation Administration and be renamed the National Space Agency. The U.S. must also recognize that space is an emerging arena of international competition and conflict and militarily protect its space assets from China which seeks to use space to restrict the U.S.' ability to defend its strategic interests in regions such as the Western Pacific.

The Water Entry Of Slender Axisymmetric Bodies: Forces, Trajectories And Acoustics, Kyle Gordon Bodily

Theses and Dissertations

Free surface water entry of various objects has been studied using high-speed images and image processing techniques for decades. This thesis studies the forces, velocities, and trajectories of slender axisymmetric projectiles using an embedded inertial measurement unit (IMU). Three nose shapes (cone, ogive, and flat) were used in the study. Additionally, the projectiles were tested at vertical and oblique impact angles with different surface conditions. One-half of each projectile was coated down the centerline with a hydrophobic spray, creating a half hydrophobic, half hydrophilic case. The trajectory of this half-and-half case impacting vertically was compared to the trajectory of symmetrically …

Footwear-Centric Body Area Network With Directional Uwb Antenna, Domenico Gaetano, Vit Sipal, Patrick Mcevoy, Max Ammann, C Brannigan, Louise Keating, Frances Horgan

Articles

A footwear-centric body area network employing a directional antenna is compared with waist-centric systems using omnidirectional and directional antennas. The impact of body movements on path gain is analysed for two bands at 3.99 GHz and 7.99 GHz. The path gain and data rate results demonstrate that footwear-centric configurations are equivalent or better than waist-centric body area networks.

Modified Time Of Setting Test For Fly Ash Paste And Fly Ash-Soil Mixtures, Xin Kang, Gi Chun Kang, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A survey of current literature has revealed that the testing protocol for determining the time of setting of fly ash-soil mixtures is not available. Although the current ASTM standard recommends using the Vicat needle method with a water-to-fly ash weight ratio of 0.35, it was originally proposed for testing the time of setting of cement. The current study showed that the Vicat needle method yielded poor test results for some common fly ashes. Moreover, the water-to-fly ash weight ratio of 0.35 may not be appropriate for some fly ashes because the chemical components are varied in different fly ashes. Therefore, …

Cryogenic Carbon Capture Using A Desublimating Spray Tower, Bradley J. Nielson

Theses and Dissertations

Global warming is becoming ever increasing concern in our society. As such the likelihood of a carbon tax in the US is becoming increasingly likely. A carbon tax will be expensive enough that coal-based power plants will either have to install carbon capture technology or close. The two front runner technologies for carbon capture are amine scrubbing, and oxyfuel combustion. The downside is that both of these technologies increase power generation cost in a new plant by about 80% and have up to a 30% parasitic load, which reduces the cycle efficiency, that is, the power production per unit fuel …

Centrifuge Modeling And Mitigation Of Manhole Uplift Due To Liquefaction, Gi Chun Kang, Tetsuo Tobita, Susumu Iai, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Because low-compacted trench backfill around a manhole is normally liquefiable, the manhole could suffer uplift damage associated with soil liquefaction during a strong earthquake. In this study, 22 dynamic centrifuge models were tested to investigate the response of a buried manhole subjected to a dynamic load. The models were tested under 20g, and a substitute pore fluid was used to avoid the scaling law conflict between the dynamic and diffusion processes. It was found that excess pore water pressure is one of the contributing factors to the magnitude of the manhole uplift. Using this result, new mitigation methods against the …

Portable Pressure Device To Evaluate Lateral Formwork Pressure Exerted By Fresh Concrete, Ahmed F. Omran, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Use of a reliable and accurate measuring system to determine lateral pressure exerted on formwork by self-consolidating concrete can lead to economic and safe formwork systems. In this paper, a portable and field-compatible pressure device is developed to enable factors affecting lateral pressure of fresh concrete on formwork system to be explored prior to conducting onsite full-scale tests. The pressure device requires a sample of 16 L of fresh concrete to determine lateral pressure envelope that can be exerted by a concrete column of up to 13 m in height. The pressure device enables the simulation of such concrete head …

A Parabolic Equation Analysis Of The Underwater Noise Radiated By Impact Pile Driving, Nathan Laws

Dissertations and Theses

Impact pile driving can produce extremely high underwater sound levels, which are of increasing environmental concern due to their deleterious effects on marine wildlife. Prediction of underwater sound levels is important to the assessment and mitigation of the environmental impacts caused by pile driving. Current prediction methods are limited and do not account for the dynamic pile driving source, inhomogeneities in bathymetry and sediment, or physics-based sound wave propagation.

In this thesis, a computational model is presented that analyzes and predicts the underwater noise radiated by pile driving and is suitable for shallow, inhomogeneous environments and long propagation ranges. The …

Aqueous Henry's Law Constants, Infinite Dilution Activity Coefficients, And Water Solubility: Critically Evaluated Database, Experimental Analysis, And Prediction Methods, Sarah Ann Brockbank

Theses and Dissertations

A database containing Henry's law constants, infinite dilution activity coefficients and solubility data of industrially important chemicals in aqueous systems has been compiled. These properties are important in predicting the fate and transport of chemicals in the environment. The structure of this database is compatible with the existing DIPPR® 801 database and DIADEM interface, and the compounds included are a subset of the compounds found in the DIPPR® 801 database. Thermodynamic relationships, chemical family trends, and predicted values were carefully considered when designating recommended values. Henry's law constants and infinite dilution activity coefficients were measured for toluene, 1-butanol, anisole, 1,2-difluorobenzene, …

The Effect Of Carbon Additives On The Microstructure And Performance Of Alkaline Battery Cathodes, Douglas Robert Nevers

Theses and Dissertations

This thesis describes research to understand the relationships between materials, microstructure, transport processes, and battery performance for primary alkaline battery cathodes. Specifically, the effect of various carbon additives, with different physical properties, on electronic transport or conductivity within battery cathodes was investigated. Generally, the electronic conductivity increases with carbon additives that have higher aspect ratios, smaller particle diameters, higher surface areas, and lower bulk densities. Other favorable carbon aspects include more aggregated and elongated carbon domains which permit good particleto-particle contacts. Of the various carbon additives investigated, graphene nanopowder was the best performer. This graphene nanopowder had the smallest particle …

Dynamics And Control Of Wrist And Forearm Movements, Allan W. Peaden

Theses and Dissertations

Wrist and forearm motion is governed both by its dynamics and the control strategies employed by the neuromuscular system to execute goal oriented movement. Two experiments were conducted to increase our understanding of wrist and forearm motion. The first experiment involved 10 healthy subjects executing planned movements to targets involving all three degrees of freedom (DOF) of the wrist and forearm, namely wrist flexion-extension (FE), wrist radial-ulnar deviation, and forearm pronation-supination (PS). A model of wrist and forearm dynamics was developed, and the recorded movements were fed into the model to analyze the movement torques. This resulted in the following …

A Study Of Action Origami As Systems Of Spherical Mechanisms, Landen A. Bowen

Theses and Dissertations

Origami, the Japanese art of paper folding, has been used previously to inspire engineering solutions for compact, deployable designs. Action origami, the subset of origami dealing with models designed to move, is a previously unexplored area for engineering design solutions that are deployable and have additional motion in the deployed state. A literature review of origami in engineering is performed, resulting in seven key areas of technical origami literature from a wide variety of disciplines. Spherical mechanisms are identified as the method by which most action origami models achieve complicated motion while remaining flat-foldable. The subset of action origami whose …

Method And Apparatus For Measurement Of Fluid Properties, Feredoon Behroozi

Patents (University of Northern Iowa)

A method and apparatus for determining the contact angle and/or surface tension of a liquid on a solid surface is described. The method involves placing a fluid drop on a solid surface, and gradually increasing its volume by adding more fluid, while continuing to determine the corresponding increase in fluid height, until the drop attains maximum height beyond which additional fluid only increases the drop footprint and not height, and determining the equilibrium height and in turn the contact angle by means of an equation that correlates contact angle with depth below the fluid surface, together with the fluid surface …

Capillary Filling Of Large Aspect Ratio Channels With Varying Wall Spacing, Dallin B. Murray

Theses and Dissertations

Quantification and prediction of capillary fluid flow in planar nanochannels is essential to the development of many emerging nanofluidic technologies. Planar nanochannels are typically produced using the standard nanofabrication processes of thermal bonding or sacrificial etching. Both approaches may yield nanochannels that are bowed and/or exhibit non-uniform (i.e. non-planar) wall spacing. These variations in wall spacing affect the transient dynamics of a liquid plug filling the nanochannel, causing deviations from the classical behavior in a parallel-plate channel as described by the Washburn model. Non uniform wall spacing impacts the overall frictional resistance and influences the meniscus curvature. In this thesis, …

Why Do Indiana Pre-Service Technology Education Majors Choose The Profession, Traves L. Freeland

Purdue Polytechnic Masters Theses

The purpose of this descriptive study was to look at the factors that influence pre-service technology education majors to choose to become teachers. The pre-service teachers of three Indiana technology education teacher preparatory programs were given an internet survey to collect demographic data and determine what factors influence current pre-service teachers. The results of this study were compared to the results from a study done by Harris (2007). The findings resulted in similar factors that were the most common identified as being influential. Those factors included personal interest or hobbies, high school or middle school teacher, and past experiences in …

Energy Dissipation Of Thin-Walled Cold-Formed Steel Members, David A. Padilla-Llano, Christopher D. Moen, Matthew Eatherton

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.