Engineering Commons^™

Testing Of Missouri Shales For Light Weight Aggregate Production, Jerry D. Plunkett

Masters Theses

"The original objective of this investigation was to determine by testing those clays, shales, and loesses occuring in Missouri in large deposits (over 15 feet in thickness with little overburden), which would be suitable for the production of light weight aggregate. The second objective was to investigate the mechanism of bloating as related to the physical and chemical properties of the above materials, and by using these relationships cause clays which do not naturally bloat, to bloat using some addition. The use of additives would permit the economical use of material closer to the market in many instances.

After the …

The Design And Construction Of An Electronic D-C Analog Computer, Frederick R. Wagner, William A. Paar

Masters Theses

"To make this project realizable with the funds available and in the time allowed, and to set forth some definite goals, the following objectives were adopted:

1. Design, construct, and place in working order a d-c electronic analog computer capable of solving 4th order linear differential equations with constant coefficients.
2. Include in the design provisions for real time computation, and also fast, repetitive operation.
3. Provide for later expansion of the computer installation.
4. Limit expenditures to $700"--Introduction, page 4.

Heat Flow In A Two-Dimensional Steady-Flow System Without Radial Symmetry, George H. Parharoglu

Masters Theses

"As the extent of the science of heat conduction depends on the multiplicity of the boundary conditions that can be applied to the basic differential equation, a particular case in which the use of one set boundary conditions for the development of the general equation for the temperature distribution as well as the the amount of heat flow in a steady-state, two-dimensional heat flow system with a source of heat plased at the center of or along the axis of a cylinder, and without radial symmetry has been the object of this problem. Radial symmetry means the variation of temperature …

Deposition Of Metallic Coatings From Fused Salt Baths, Andrew Hessler Larson

Masters Theses

"This thesis is the result of an investigation undertaken to study some of the important factors affecting the deposition of metallic diffusion coatings on other metals immersed in a fused salt bath….

There are many methods which have been devised to obtain diffusion coatings on various metals. One which is quite well known and used commercially is the process of “chromizing” which produces a diffusion layer if chromium on another metal. One method of “chromizing” consists of immersing the specimen to be coated in a mixed chloride fused bath containing chromium metal flakes. Another method consists of packing a low …

Effect Of Carbon Content In Steels Upon The Deposition Of Titanium From A Fused Salt Bath, Reinhard Paul Abendroth

Masters Theses

"STATEMENT OF PROBLEM Previous work done at the Missouri School of Mines and Metallurgy on the deposition of titanium upon various metals, especially iron and steel, bas shown that titanium can be deposited upon ingot iron and. low carbon steels with comparitive ease. Difficulty was encountered in attempts to deposit titanium upon steels of higher carbon content and upon cast irons.

For this reason, it was decided to investigate more thoroughly the relationship between the carbon content of various steels and the quality of titanium coatings deposited on these steels. Once this relationship had been established, a suitable theoretical explanation …

Corrosion Products Of Titanium In Fused Salt Baths, Kai-Chai Chiou

Masters Theses

"Titanium is gaining great interest in the modern metal industry because of its natural abundance and its desirable physical and chemical properties. Among them, its excellent corrosion resistance, such as the resistance to normal atmosphere attack, humid and saline atmosphere attack, sea water attack, and nitric acid attack, is the most prominent characteristic being welcomed by the engineers. The usefulness of titanium would be greatly increased if it were possible to plate titanium on other metals, thus increasing the corrosion resistance of these other metals.

Much concern, at present, has been given to the possibilities of the electrodeposition of titanium …

Mechanism And Measurement Of First Stage Graphitization In White Cast Iron, David S. Gould

Masters Theses

"The original object of this thesis was to ascertain if coercive force measurements could be used for the determination of degree of malleablization in malleable iron. Since first stage graphitization was involved, it was only natural that an interest in the mechanism of first stage graphitization developed. The investigation which resulted from this interest was done primarily for the edification of the author, however it was subsequently deemed of enough importance to be included in this thesis. For this reason the thesis may appear at times to deviate from the original objective"--Preface, page iii.

Tunnel Rehabilitation, Jay C. Dotson

Masters Theses

"This paper is an outgrowth of research conducted at Missouri School of Mines and Metallurgy over a two year period. The purpose of the study is to assemble into one volume information that is pertinent to the rehabilitation of tunnels. Notwithstanding the voluminous size of the paper, much descriptive material necessarily has been omitted because of the far-reaching scope of tunneling practices and of the specialized fields therein. An extensive bibliography has been prepared to supplement the material that has been selected for presentation. Through consultation with tunnel men of all ranks, observations in the field, and an intensive search …

The Steel Industry Of India: Its Historical Background And Present Development, Glenn Kaufmann

University of the Pacific Theses and Dissertations

Ancient India was reported to produce excellent iron products that were prized in all parts of the world. Not only did she make swords, plow points, and other products necessary for the useful arts, but also ornaments such as ear and finger rings, and iron ornaments to beautify her buildings. India today, though to a lesser degree, is still carrying on the tradition of hand-made iron ornaments, by using the ancient method of smelting and processing. Indian wootz, a product similar to steel, was the best iron product made in olden times, and only India's failure to develop new and …

An Investigation Of The Characteristics Of High Alumina Refractory Castables, Gajendra Nath Mohanty

Doctoral Dissertations

"Refractory castables or concretes, a comparatively new member of the refractories family, are an admixture of highly aluminous cements and graded refractory aggregates, blended in predetermined proportions very much like structural concrete. The refractory aggregates must contain a large amount of fines contrary to the requirements of ordinary concrete. Unlike the Portland cements, which are mainly combinations of calcium silicates, the highly aluminous cements are predominantly calcium aluminates. They are comparatively of a refractory natures, having the hydraulic setting property combined also with high early strength. The discovery of the fact that these refractory concretes could be cast, in situ, …

The Rate Of Dissolution Of Aluminum In Hydrofluoric Acid, Yen-Ngen Wang

Doctoral Dissertations

"Pure aluminum has a relatively low strength, and its use is, therefore, rather limited. However, the resistance of pure aluminum to the attack of acids and many neutral solutions is higher than that of less pure aluminum or most of the aluminum-base alloys. For this reason, alclad alloy sheets, are made with a coating of pure aluminum on one or both sides of an aluminum alloy core. The coating is metallurgically bonded to the core over the entire area of contact. Thus the coating electrochemically protects the core from corrosive attack.

Aluminum is more negative in the electrochemical series than …

Hydrogen Overvoltage On Titanium, Sheng-Tai Shih

Doctoral Dissertations

"The hydrogen overvoltage has been defined as the difference between the potential of the working electrode (cathode) and the theoretical reversible value for the same solution. This definition brings out the difficulty involved in the measurement of the "theoretical reversible potential for the same solution” as the potential of the hydrogen electrode in such a solution is usually different from the value of a standard reversible hydrogen electrode, for which the activity of hydrogen ions is set as being “1” and the potential arbitrarily set as being “0”. Besides, it is sometimes necessary to add addition agents to the solution …

A Study Of The Deformation Texture And Its Variation In Cold Drawn Nickel Rods, Krishan Kumar Tangri

Doctoral Dissertations

"The production of rods by cold drawing is a development of recent years as compared to other methods of fabrication. Though a good many investigations correlating the observed mechanical properties to the mill practices employed have been reported, the results nevertheless are more of a qualitative and empirical nature. It is well known that the physical properties of a metal product are related to its deformation textures which are characteristic of the metal and the fabricating method used. Thus a study of the deformation textures of cold-drawn rods, specially by x-ray diffraction techniques should provide a much more precise and …

The Application Of Electric Energy To The Metallurgy Plants In Montana, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Since the year 1800, metallurgy has been affiliated with electricity. In fact, the two industries have grown side by side, being naturally dependent upon each other and having a parallel growth.

Sediment Movement In Bear River, Utah, Calvin Geary Clyde

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

In the northern part of Cache Valley, Utah, accelerated erosion in recent decades has cut deep gullies of impressive size into the flat, irrigated bench land along the Bear River. Millions of tons of fine sediment have been washed into the river and great amounts have been deposited in the river bed. The resulting flooding and high water-table have caused much damage to the land near the river.

I. Certain Azo Dyes Derived From 2-Amino Phenol-4-Sulfonic Acid; Ii. A Study Of The Reduction Rate Of 2-Nitro Phenol-4-Sulfonic Acid, Albert Edward Cohen

Theses

No abstract provided.

Calcium Metal : Laboratory Preparation By Vacuum Metallurgy, George Robert Couch

Theses

No abstract provided.

Adiabatic Distillation Of Dilute Formaldehyde Solutions, Robert L. Craven

Theses

No abstract provided.

The Influence Of Agitation On A Continuous Counter-Current Liquid-Liquid Extraction Column, William John Hartmann

Theses

This work presents operating data and correlations of agitated extraction equipment studied under continuous counter-current flow.

The experimental work was carried out in at agitated column 36 inches in length with an internal diameter of 2 inches using the system toluene, benzoic acid and water. The working section of the column was 24 inches. The design of the column used for the experimental work is similar to that proposed in a patent by van Dijck (3). The column is similar only to the extent that the patent covers numerous conditions of vertical agitation.

The distribution data and the equilibrium solubility …

The Construction And Operation Of A Universal Specimen Mount With Protective Lead Shield For The Purpose Of Determining Pole Figures Using The Schulz-Decker Transmission Technique, Richard L. Fausner

Bachelors Theses and Reports, 1928 - 1970

It was the purpose of this study to construct a universal mount, to construct a protective lead shield, to operate the instrument, and to provide a pole figure using the transmission method of Schulz and Decker. There are at present several lengthy x-ray methods of determining the grain orientation of metals. These methods are mainly photographic. In order to provide a rapid means of obtaining the necessary information concerning the grain orientation of a metal, a universal mount was constructed.

The Lucky Hit Mine Of Jefferson County, Montana, Bruce B. Goddard

Bachelors Theses and Reports, 1928 - 1970

Many mines in the Cardwell Mining District have been more or less steady producers of gold, silver, lead and zinc since 18SO. The area first came into prominence with the discovery of gold at the Mayflower Mine in 1896. Soon after the Mayflower discovery, many claims were located in the nearby Saint Paul Gulch area, northeast of Whitehall. The Lucky Hit Mine is located in Saint Paul Gulch area of the Cardwell Mining District.

Nonmetallic Mineral Resources Of Montana (Except Fuels), F. L. Rytlewski

Bachelors Theses and Reports, 1928 - 1970

Essentially, the paper is composed of seven parts, each of which concerns a group of related nonmetallic minerals such as ceramic materials, gemstones, or abra­sives. Following the data pertaining to the minerals of each group are index mars locating the major mineral deposits which are known to date. Production and reserve figures are listed by tables in cases where such information is available.

Stratigraphy Of Kootenai In Montana, B. B. Jarrett

Bachelors Theses and Reports, 1928 - 1970

The Kootenai of Montana is a variable formation as far as composition is concerned. The formation consisting largely of a series of sandstones, shales, and shaly sandstones. The presence of the limestone and carbonaceous members being irregular indicating variable climatic conditions throughout the deposition of the sediments. The fresh water environment being confined to the western slope, while the central and the eastern portions had more swampy conditions with local fresh water depositions.

Nitration Of Derivatives Of 2,5-Dichlorobenzenesulfonic Acid, William J. Conradi

Theses

The proof that a nitro group enters meta to the sulfonic acid group of 2,5-dichlorobenzenosulfonamide and 2,5-dichlorobenzenosulfonanilide is presented.

The preparation of several new compounds is described.

An unsuccessful attempt to prepare 2,5-dichloro-3-nitrobenzenesulfonyl chloride from 2,5-dichloronitrobenzene is also described.

Preparation And Spectra Of M-Nitrobenzoates And M-Aminobenzoates, Peter Tikey Kapsamalis

Theses

A study of the synthesis of a series of new m-nitrobenzoates, m-aminobenzoates and several derivatives of the latter is presented.

Physisal constants and analytical determinations are presented, including the ultraviolet absorption spectra of the compounds prepared.

Substituted Ureas, Roy Earl Parks

Theses

Nitrosomethylurea in aqueous medium decomposes on heating to methanol, nitrogen and cyanic or isocyanic acid. Primary amines present during the decomposition react with cyanic acid to form substituted ureas, readily isolated in high purity and good yield.

The Effect Of Surface Tension Upon The Flow Of Fluids Through Packed Beds, William Charles Streib

Theses

Flow tests through beds of unconsolidated sand, glass beads and 1/4 inch Berl saddles showed that wide variations in the surface tension of a fluid had no significant effect on its flowrate through the bed. Viscosity and density were the only fluid properties affecting such flow. Excellent comparative results were observed between the flowrates through sand beds and those predicted by the Leva equation.

The complex Brownell and Katz equation for predicting the residual saturation of a packed bed was found to apply for fluids having a much wider range of surface tension than those originally used to derive their …

The Development Of Executives, Joseph Ralph Messineo

Theses

The ever-increasing trend toward improved industrial efficiency creates the problem of supplying capable executives. The supply of executive manpower in business corporations ever needs replenishing. Expansion of operations, retirements, and other circumstances cause executive demands and vacancies which must be filled. Therefore, the purpose of this thesis is to analyze and report on what industry is actually doing today to develop executives to meet present and future requirements. Also, it is the author's intent to formulate a comprehensive executive development program that can be adopted with some limitations by industry for the building of an executive reserve.

In order to …

Ultrafiltration In The Pigment Field : A Critical Literature Survey, Charles Walter Manger

Theses

The objective in this work has been to determine, through a critical literature survey, the possible application of ultrafiltration, and other related techniques, towards the solution of certain problems encountered in the research and testing of various pigments.

Among these problems may be mentioned the following:

1. The determination of water-soluble salts in pigments, which when dispersed in water to leach out the salts, tend to peptize, thus being unfilterable through the usual filter paper. Among these pigments are the following: iron blue, certain chrome yellows, pigment green B, copper maroon, and several others. It may be added that these pigments …

Correlation Of The Number Of Theoretical Plates Vs. Reflux Ratio, George Ignatius Parisi

Theses

A correlation is presented from which the number of theoretical plates for a given separation by distillation can be estimated as a function of the reflux ratio. The effects of relative volatility and feed composition upon such a correlation are also studied. Smoker's (1) equation was used in calculating the data. The results were obtained by varying the several parameters which have to be given for any separa tion desired. These include feed compositions of 0.25, 0.50, and 0.75; relative volatilities of 1.1, 1.2, 1.5, and 2.0; and various reflux ratios. The overhead product and bottoms product compositions were kept …