Engineering Commons^™

Viscosity Determination During Polymerization, Elmer David Jones

Theses

This project was undertaken for the purpose of designing, constructing, and operating a viscometer which could be employed for measuring viscosities in the range of 200 to 700 poises at temperatures up to 300°C. Such an instrument was built and used to study the viscosity of Type EV polymer during polymerization.

The new viscometer is based cm the principle of concentric rotating cylinders. It is unique in that it can be suspended directly in a polymer batch and will operate under temperature and viscosity conditions as outlined above. Polymerization curves for batches studied show that the instrument gives viscosity values …

Investigation Of The Acid Degradation Of 2-(4-Methoxybenzylamino)-Pyridine, Anthony Thomas Oropollo

Theses

This paper represents work done in connection with an investigation of the products resulting from the reaction of dilute sulfuric acid and 2-(4-methoxybenzyl-amino)-pyridine. Brief contact between these reactants at temperatures below 80°C give rise to a water soluble salt of the amine. The amine may be precipitated from the solution by the addition of sufficient alkali.

Under the conditions considered in this paper, prolonged contact of reactants at temperatures above 80°C, a non-crystalline condensation product is obtained in addition to the amine salt.

Attempts to identify this product were unsuccessful. However, in connection with the characterization work, two relatively little …

Geology Of An Area Near Montana City, Montana, Frank A. Crowley

Bachelors Theses and Reports, 1928 - 1970

The investigated area lies about five miles south of Helena, Montana, near the abandoned gold camp of Montana City. Topographically, the area reflects the sedimentary formations and the igneous rocks, quartz monzonite and rhyolite. Static recrystallization of the sedimentary rocks caused by the intrusion of the Boulder Batholith, along with deformation of sedimentary beds by pre-batholithic folding and by post-batholithic faulting have complicated the geologic picture.

The Placer Deposits Of The Siberia District (German Gulch), Montana, Ronald D. Karvinen

Bachelors Theses and Reports, 1928 - 1970

The original concept of this problem was to determine if hidden or buried placers existed past the terminal point of the extensive placering in the Siberia District. Several theories have been advanced for the sudden cessation of those placers. All are plausible, and are both for and against an extended placer. The past history relates that some $13,000,000 in gold has been produced in the area, therefore stressing a practical search for additional accumulation.

Leaching As A Method Of Mining Uranium, Rob L. Kane

Bachelors Theses and Reports, 1928 - 1970

This paper presents a new method of recovering uranium ores from the earth. By sinking drill holes into ore bearing beds, aqueous leach solutions can be circulated through the ores. Solutions of sulfuric acid, potassium carbonate and many other available reagents will put the ions of uranium and vanadium into the liquid leach. The pregnant solutions are then pumped to the surface so a recovery of the valuable portion of the ore can be made.

Shaft Sinking Investigation, Harold Foss

Bachelors Theses and Reports, 1928 - 1970

This paper, investigating shaft mucking, has been prepared as a partial requirement for the degree of Bachelor of Science in Mining Engineering. In the following material I have attempted to collect and compile all available information on mechanical shaft mucking, to compare and contrast the different methods and to trace their development through to the latest innovation. This development of the investigation is purposely being used to lead to a new method which will be discussed hypothetically as a conclusion to the paper.

Fluorite On The Wrong Font Claim, Robert L. Clayton

Bachelors Theses and Reports, 1928 - 1970

The Wrong Front claim lies west of Butte near Nissler Junction. It is owned by Thomas J. Helehan of Butte. The deposit is epithermal and lies within the Boulder Batholith. The host rocks are granite, alaskite and andesite with granite being the most prominent host rock.

Beneficiation Of Scheelite Ore From The Potosi Tungsten Mining District, James A. Ndulue

Bachelors Theses and Reports, 1928 - 1970

The now increasing importance of tungsten as a metal with desirable properties in high strength and high temperature resisting alloy steels, coupled with the recent discoveries of low-grade tungsten ore deposits in Montana, has spurred a search for suitable and economical methods of treating tungsten ores of the State. This search has been conducted on a variety of tungsten ores and the present work is rather an aspect of the whole tungsten beneficiation problem in Montana.

The Transient Response Of A Distributed Amplifier, Thomas D. Lusk

Electrical and Computer Engineering ETDs

The purpose of this paper is to describe the transient behavior of a simple constant-K distributed amplifier stage. The derivation of the transfer function is carried out using the Laplace Transform for the case where losses in the lines are considered to be zero. The various characteristics of the amplifier response to a unit step function are discussed and the effects of losses and other modifying factors upon the idealized response are evaluated. Finally design procedures are derived which allow the circuit designer to determine the circuit parameters necessary for good transient responses. These procedures are applied to the design …

An Experimental And Theoretical Investigation Of The Characteristics Of A Magnetic Amplifier, Merle H. Wittmeyer

Electrical and Computer Engineering ETDs

Many excellent analyses of magnetic amplifiers have been published. As in every investigation, however, there are many details not explained. The purpose of this investigation was to explain some of the details of magnetic amplifier characteristics.

An Investigation Of A Dustless System Of Dry Drilling, Norman J. Hardt

Bachelors Theses and Reports, 1928 - 1970

For many years the problem of removing dust particles while drilling dry has confronted the mining and construction industries. In areas where water is not available, rock drilling is still being done under hazardous dust conditions. It was in an attempt to find a partial solution to this problem that the material contained in this report was compounded.

Application Of The Rotary Principle To Underground Mucking, Walter J. Smit

Bachelors Theses and Reports, 1928 - 1970

Since the beginning of man's utilization of rocks and minerals, he has felt a need for an efficient mover of these materials. Thus, he turned from the sole use of his hands to the development of the shovel, and through the other hand tools-- the hoes, and the fork, and the rake-- he finally came to the manufacture of the heavy, more efficient, large-scale rock movers-- the muckers, and the scrapers, and duckbill loaders.

Geology Of A Mineralized Breccia "Pipe" Near Basin, Montana, James W. Allan

Bachelors Theses and Reports, 1928 - 1970

Located on the western flank of the Boulder batholith of southwestern Montana, the mineralized breccia "pipe" is opened by the Obelisk Mine. The intersection of two fault systems in the quartz monzonite of the Boulder batholith has provided the locus of the breccia "pipe". There is fairly conclusive evidence indicating that the present outcrop of the "pipe" lies only a few hundred feet below the former "roof" of the batholith.

Southwestern Extension Of The Pondera Field, Paul P. Garding

Bachelors Theses and Reports, 1928 - 1970

Oil was discovered in the Pondera field in June 1927 following work done by E.B. Emrick. The initial discovery well, located in section 17, T. 27 N., R. 4 W., was not a commercial oil producer. Its initial production being 3 barrels of oil and 3,500,000 cubic feet of gas per day. Rapid expansion followed until 1929, when the field reached its peak of production.

Tungsten Mineralization At The Strawberry Mine, Pony, Montana, Robert L. Meyer

Bachelors Theses and Reports, 1928 - 1970

The Strawberry Mine, located four miles west of Pony, Montana, for many years an intermittent producer of gold are, is once again the scene of mining activity due to the discovery of scheelite in 1953.

A Comprehensive Study Evaluating Driver Education In The Senior High Schools From Analyses Of Driving Records Of Salt Lake City High School Students, H. Keith Bushman

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Officials responsible for the control and administration of the traffic on the highways and streets of the nation are aware that good roads, markings, signals, and equipment are necessary. They also realize that the human element involved in the process of operating a vehicle is of the utmost importance. Highways can only be termed good to the extent of the actions of the drivers who use these roads.

Studies have been made throughout the nation in different states and cities to determine the results of formal training of drivers. The results of these studies answer many questions and also leave …

Survey Of Personnel Practices In Selected Industrial Organizations Of Utah, George R. Clawson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This study deals with the factors which were responsible for the origin of personnel functions in a selected group of industrial organizations in the State of Utah. Although material is available concerning the factors which affected the establishment of personnel functions in the United States in general, there is little information regarding these factors in any one region. For this reason, an area study should be of value.

Effectiveness Of Evaporation From Ground And Foliage In Reducing Soil Moisture Depletion, Val D. Wynn

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Field irrigation efficiency is the percentage of the water delivered to the field that becomes available to the crop as soil moisture. The so-called "evaporation losses" from wetted ground and foliage are rather difficult to measure, but are estimated by Christiansen (3) to be between 15 and 30 percent. No doubt part of this may be termed as a "loss," but the other part may be incorrectly termed as such. Many authorities claim that water must pass through the plant before being transpired into the atmosphere to be effectively used.

Servo-Stabilization Of Drift In Wide-Band D-C Amplifiers., Joel M. Simmons Jr.

Electrical and Computer Engineering ETDs

It was the purpose of this study to determine the suitability of a comparator and negative feedback circuit (servo-type) as a general utility method of reducing the end effect (zero-drift) of changing static characteristics of the vacuum tubes and other associated components in wide-band direct-coupled amplifiers. A brief description of the drift servo-stabilization system and its drift reducing characteristics are as follows.

New Techniques For Ore Search, Paul L. Allsman

Bachelors Theses and Reports, 1928 - 1970

This report is a survey of the newest methods in use for mineral exploration. It will attempt to review the newest techniques in the fields of geophysics, geologic research and theories of ore deposits, exploratory drilling, mapping methods and other tools of mineral exploration. Then a preview of coming and predicted techniques will comprise a summary.

Solution Of Some Chemical Plant Problems Associated With The Manufacture Of Insecticides, Lawrence Ralph Hinken

Professional Degree Theses

"This thesis describes the solutions of a variety of developmental, production, and general engineering problems encountered in a chemical plant. This plant produces resins, solvents, and insecticides. Most of the problems considered here are patented or are of a secret nature. These details are, in the main, satisfactory temperatures, molar ratios, times of reaction, and space-time data. Therefore, it is the purpose of this discussion to be general but, in the main, to give the outline of the thinking which derived these solutions. Some of these solutions were of minor economic value, some were vital to the success of the …

Design Of A Precast Concrete Deck Girder Highway Bridge, Robert V. Gevecker

Professional Degree Theses

"In the Fall of 1951, as a result of an agreement between the Portland Cement Association and the Missouri State Highway Department, with the approval and good wishes of the United States Department of Commerce, Bureau of Public Roads, the State Highway Department embarked on a program to design and construct several precast, prestressed, and precast-prestressed concrete highway bridges"--Introduction, page 1.

The purpose of this extensive program being to indicate to State Highway officials and other interested parties the advantages of these types of construction. In the words of Mr. S. W. O'Brien, District Engineer for the Bureau of Public …

The Closure Of Thin Wall Pressure Vessels, Archie W. Culp Jr.

Masters Theses

"The object of this thesis is to find various methods of closing thin wall aluminum cylinders. Such a closure must be strong enough, that when internal pressure is applied, ultimate failure will occur along a longitudinal element of the cylinder and not at the closure. Moreover, such a method must not only be mechanically sound, but it must be readily adaptable to mass production"--Introduction.

Investigation Of Soil Bricks As A Building Material, Ahmet Ilter

Masters Theses

"The need of a cheap construction material for small village farm construction in Turkey makes soil-cement a most desirable material. What is more, as far as the author knows, soil-cement has not found any application in farm house construction in Turkey as yet. So the author, being acquainted with his native country's house construction problem, and seeing the suitable application soil-cement have on such construction, came to the decision that he should investigate this problem thoroughly.

The main objective of the tests run in this investigation will be to find the strength of different samples of soil-cement. The stabilizer used …

A Study Of The Bonding By Air-Setting Refractory Mortar At Elevated Temperatures, Bhikhubhai Mahadeo Sedalia

Doctoral Dissertations

"The importance of a suitable material for the laying of bricks in furnace and kiln construction has been recognized by the refractory industry for a long time. It is necessary that a strong bond should develop between the bricks to impart strength to the entire construction work. A weak joint would form the weakest link and dangerously weaken the whole structure.

Such being the importance of the bond, the refractory industry has made quite an effort to develop jointing materials which would produce strong bonds. During the last two decades, due to intensive research and development work, many good bonding …

Carbon Monoxide Attack Of Refractories, William A. Frad

Doctoral Dissertations

"The disintegration and failure of fire clay refractories due to the action of carbon monoxide has been studied tor a period at about fifty years. The most important application is in blast furnace refractories. Similar failures due to carbon deposition, involving other gases such as methane, have been noted and less extensively studied. Failures due to the action of gases other than carbon monoxide are beyond the scope of this thesis. Occasional attempts to find some agent to prevent disintegration have been mentioned in the literature. In this study the number of such substances and the results of their action …

A Fundamental Study Of Clay Drying Using Ware Of Large Cross Section, Robert F. Grady Iii

Masters Theses

"The drying of clay has been studied extensively in the past by many investigators, some of whom attempted to relate this information to the structure of clay and thereby develop a more vivid picture, while others studied the mechanism of drying in its own right in order to present a useable theory that would allow improvements in the drying operation.

At present the literature is unable to present a theory of the mechanism of drying that is sufficiently general to cover the observed aspects of clay drying. Many and varied mechanisms are presented, but correlation is seldom completely evident between …

The Use Of A Steady State Flow Reactor In The Study Of Rapid Gas Phase Reactions, Ormond Kennedy Lay

Masters Theses

"The demonstration of the feasibility of rocket propelled devices for various purposes within the past few years has initiated an intensive search for suitable reactants for use as rocket fuels. Consequently, the investigation of the properties of chemical reactions which rapidly liberate large quantities of energy has assumed major importance. In order that such reactions may be adapted to practical use as rocket propellants knowledge of the characteristics of these reactions is required. Properties such as+ the mechanism of the reaction, the speed of the reaction under varied conditions of temperature, pressure and concentrations, the conditions required for the initiation …

An Investigation Of Continuous Steel Beams In The Plastic Range, Robert Adams Shoolbred

Masters Theses

"The purpose of this thesis is to investigate the action of beams in the plastic range. The test specimen will be a 4WF 13 structural shape continuous over three supports having equal span lengths of seven feet. Three types of loading were chosen. The first loading will be concentrated in the center of each span. The second loading will be a concentrated load in the center of one span only. The third loading will be the settlement of the two end supports until a plastic hinge forms at the center support, then the two spans will be loaded with concentrated …

Horizontal Pressures On Retaining Walls Due To Line Surface Loads, John B. Heagler

Masters Theses

"Among the oldest types of structures with which engineers have had to deal are those which serve to laterally restrain masses of earth, or to prevent earth embankments from assuming their natural angle of repose. This is necessary where space is limited or the natural slope would encroach upon other property. These structures, usually called retaining walls, are subjected to forces, both lateral and vertical due to the pressures exerted by the backfill material and any loads imposed on the backfill material. The first step in the design of the retaining wall is to determine the magnitude, position, and line …