Engineering Commons^™

Improving Technology For Producing Complex Fertilizer From Low-Grade Phosphorites Of The Central Kyzylkum, A.Zh. Allamuratova, A.U. Erkaev, A.M. Reimov, Saparbay Kazakhbaev, Dilshodbek Kurbiyazov

Chemical Technology, Control and Management

The methods of nitric acid processing of phosphate raw materials are analyzed. A technology has been developed for the nitric acid processing of phosphate raw materials into nitrogen-phosphorus fertilizer with the implementation of the process in a condensed pulp by adding sulfuric acid. A technology for producing complex fertilizers with a wide range of N:P₂O₅:K₂O ratios with improved physico-chemical parameters due to the introduction of various potassium salts into the process is proposed.

Artificial Neural Network Based Grain Moisture Measuring Device, Erkin Eljaev, Shohrux Nurali O‘G‘Li Narzullayev, Elyor Faxriddinovich Khudoyberdiev

Chemical Technology, Control and Management

To date, the intellectualization of solving technical issues in managing, controlling, and measuring technological processes in all branches of industrial production is considered an urgent task. In this regard, a class of intelligent devices and sensors has emerged. Intelligent devices and sensors differ from their analog counterparts in that they have functions such as automatic adjustment of the measurement range, self-calibration, data processing, and decision-making. The article discusses the development of intelligent measuring instruments based on a capacitive transducer for measuring the moisture content of grain and grain products.

Thermogravimetric Analysis And Chemical Kinetics Of Waste Tires, Mahir Mohammed Said

Tanzania Journal of Engineering and Technology (TJET)

The focus of this paper is to analyse the pyrolysis reaction of waste tires. The pyrolysis was studied experimentally using thermal and chemical kinetics. The tires were pyrolyzed using thermogravimetry at a temperature range of 200 to 600°C, with heating rates of 10, 20, and 50°C/min. The activating energy was observed to increase with increased temperature. The highest activating energy was 101.02 kJ/mol at a heating rate of 50°C/min.

Enhanced Post Deposition Annealing Conditions On The Fabrication Of High Quality Thermochromic Vanadium Dioxide Films, Nuru R. Mlyuka

Tanzania Journal of Engineering and Technology (TJET)

Sputter deposition of thermochromic VO2 thin films for smart window applications has been faced with several challenges including the need for high deposition temperature, extremely precise and narrow range of oxygen/argon flow ratio and target poisoning during sputtering. Deposition of VO2 at room temperature without oxygen followed by post-deposition annealing has been cited as one of the potential mitigations to the challenge. In this study, the effects of post-deposition annealing conditions on the structural, electrical and optical properties of VO2 thin films are reported. The films were prepared on soda lime glass substrates using DC magnetron sputtering of metallic vanadium …

Causes And Consequences Of Inefficient Drilling And Blasting In Mine Development Headings: A Case Study Of Hard Rock Gold Mining Operations In Northern Tanzania, George Bennett

Tanzania Journal of Engineering and Technology (TJET)

Despite the introduction of the perimeter blasting technique at the Tulawaka Gold Mine, the mine continued to suffer from an overbreak of mine development headings, with an average overbreak of 24% every 22 m, which is approximately twice the acceptable 10% overbreak. The causes of this problem include ineffective drilling practices and uneven and excessive charging of explosives, resulting in a slightly high powder factor of 3.94 kg/m3 instead of 3.8 kg/m3, as per the design. The problem of overbreak resulted in ore dilution, a longer mine development cycle time and additional costs of approximately US$ 45 per cut, especially …

An Optimization Tool For A Standalone Photovoltaic System, Johanes Kasilima

Tanzania Journal of Engineering and Technology (TJET)

Stand-alone photovoltaic systems (SAPV) are often used in remote areas where access to grid electricity is limited. This system depends on solar energy. However, Photovoltaic (PV) systems need a greater initial investment than conventional sources of energy, and their effectiveness is reliant on a number of environmental conditions such as the unpredictable solar radiation. One step in reducing the investment cost of a PV system is determining the optimal size of solar PV components that minimize costs. This paper presents a Particle Swarm based optimization tool for sizing Stand-alone PV systems. The optimization tool selects the optimal Levelized Cost of …

Design And Optimization Of An Azeotropic Distillation Pilot Plant For The Production Of Pure Ethanol, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

This study aimed to design an azeotropic distillation plant using Aspen Plus® V10 software and determine optimal process conditions for producing pure ethanol greater than 95% from pre-concentrated near-azeotropic ethanol-water solution. The non-random two-liquid Redlich-Kwong thermodynamic model was the base method for property analysis and performance prediction. Modelling and simulation of the converged process were conducted for fixed column variables (R = 5, N = 12 and p = 1 atm). Plant operating parameters were varied in the range of 0 to 1 for the pre-heater vapour fraction, 2 to 10 for the column feed plates (NFP), 2 to 6 …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Effect Of Zr And W Doping On Microstructures, Transition Temperature And Solar Transmittance Modulation Of Thermochromic W/Zr Co-Doped Vo2 Thin Films, Haji F. Haji

Tanzania Journal of Engineering and Technology (TJET)

Thermochromic W/Zr co-doped VO2-based thin films with different concentrations of Zr were successfully deposited on soda lime glass substrates by direct current (DC) magnetron sputtering of V(99)W(01) alloy and Zr targets at a substrate temperature of 425 °C. The films were characterized by x–ray diffraction (XRD), atomic force microscopy (AFM), Rutherford backscattering spectroscopy (RBS), two-point probe and UV/VIS/NIR spectroscopy. The film’s structural properties evolution was significantly influenced by Zr concentration in the films. The transition temperature and hysteresis loop widths of the films were found to decrease with increasing Zr concentration. For the Zr concentrations of 0.21 at.%, 0.23 at.% …

Evaluation Of Cybersecurity In Remote Working Settings For Mobile Network Operators, Victoria Mahabi

Tanzania Journal of Engineering and Technology (TJET)

Cybersecurity has increasingly been a primary concern to people as technology advances and allows them to work remotely. This study thus evaluated the cybersecurity posture for organisations that have opted for remote working culture, whereas emerging cyber threats, practices to combat them, and appropriate guidelines for managing cyber threats were discussed. The study used a descriptive design with a quantitative approach from 118 information technology personnel working for Tanzania's three major mobile network operators (MNOs). SPSS analysed the collected data. The study revealed that predominant cyber-threats affecting MNOs in remote working include human errors, phishing attacks, malicious domains, denial of …

Sol-Gel Synthesis And Microstructure Characterization Of Nio-Tio2 Semiconductor, Godlisten N. Shao

Tanzania Journal of Engineering and Technology (TJET)

NiO-TiO2 is a fascinating p-n semiconducting binary metal oxide with unique electronic and optical properties. The NiO-TiO2 has been synthesized using complicated preparation methods and expensive precursors that hamper their large-scale production. The present study reports the preparation of NiO-TiO2 semiconductor with improved physicochemical properties. NiO-TiO2 samples were prepared through one-pot sol-gel synthesis process followed by sintering of the as-synthesized materials at temperatures ranging from 600 to 1000 °C. The role of thermal treatment and NiO content on the microstructures was exquisitely studied. The microstructure of the NiO-TiO2 samples was examined by Raman spectroscopy, XRD, XRF, SEM-EDAX, high resolution TEM, …

General Hydrogeochemical Characterization Of Groundwater In Coastal Aquifers Of Kilwa Kisiwani Oceanic Island, South East Tanzania, Simon R Melchioly

Tanzania Journal of Engineering and Technology (TJET)

The main objective of this study was to determine the hydrogeochemical processes controlling the groundwater chemistry on the Island and assess its suitability for human consumption and irrigation. The methodology used in the study include hydrogeological assessment of the study area and laboratory analysis for general physico-chemical parameters of groundwater. Other parameters such as Soluble sodium percentage (SSP) or % Na+, Sodium Adsorption Ratio (SAR), Magnesium adsorption ratio (MAR), Residual sodium carbonate (RSC), hydrochemical facies classification, and Water Quality Index (WQI) were calculated using empirical formulae. The effects of salinization of groundwater were classified using the chloride-Bicarbonate (Cl/HCO3) and the …

Experimental And Numerical Studies On The Compressive Strength Test Of Recycled Aggregate Concrete Using Digital Image Correlation, Bastian Okto Bangkit Sentosa, Joshua Ferdinand, Nuraziz Handika

Makara Journal of Technology

The utilization of recycled aggregate (RA) as substitute of natural aggregate in concrete contributes to the research of sustainable building construction materials. Many applications of RA have been studied worldwide. However, the application of RA with a specific range of strength and specific damage behavior requires further study. This research aims to examine the mechanical characteristics of RA concrete, particularly its load–displacement response and crack pattern, through the experimental and numerical studies of compressive strength test. Laboratory concrete waste from cylindrical sample with 30–35 MPa strength was chosen as RA. The digital image correlation (DIC) method was applied throughout the …

Information Model Based On Parameters Of A Combined Soil Preparation Until For Planting, Azmuddin Sadriddinov, Anvar Abdazimov, Faxraddin Mavlanov, Hursand Madrakhim Ugli Rakhimov

Technical science and innovation

The article describes in detail the development of a combined pre-sowing machine as a result of the literature analysis of the scientific research conducted on pre-sowing tillage machines and its use and working process. In addition, the article provides scientifically based information about the factors affecting the leveler-softener and previous work on their improvement. The current state of tillage before planting in Uzbekistan and the size of the tilled fields are studied and tabulated. In order to optimize the parameters of the developed machine and minimize costs, as well as to increase its efficiency, it is devoted to the creation …

Sediment Characteristics And Hydrocarbon Composition Of Makukwa Seep In Southern Tanzania: Potential Implications For Subterranean Hydrocarbon Accumulation, Makungu M. Madirisha

Tanzania Journal of Engineering and Technology (TJET)

Exploring the interplay between natural seeps and nearby sediment and hydrocarbon properties is key to unlocking subsurface hydrocarbon potential. This study presents findings on the hydrocarbon composition and sediment characteristics of the Makukwa seep in southern Tanzania, providing insight into subterranean hydrocarbon accumulation. Sediment analysis across areas A and B, located approximately 20 m apart, showed a decrease in porosity with depth, indicative of typical sandstone formations. Area A, near the seeps, exhibited porosity ranging from 23% to 36%, whereas Area B, further away, showed porosity ranging from 22% to 38%. This suggests that a lower cretaceous sandstone layer may …

Experimental Analysis Study Wave Drift Force Of Moored Floating Production Units (Fpu), Arifin Rifliansah, Wibowo Harso Nugroho

Makara Journal of Technology

Drift forces caused by sea waves and currents are an important aspect that needs to be studied in planning moored floating structures, especially Floating Production Units (FPU) type ships which are operated for oil and gas exploration. This study describes the drift forces on the FPU which is subjected to environmental loads in the form of waves. The slow-drift movement that occurs in a moored FPU, and experiencing irregular waves is a very important problem. The complexity of determining drift forces analytically and numerically requires the use of hydrodynamics model test. In the model test on a certain model scale …

Hybrid Method Neighbor Node Discovery In Wireless Sensor Networks: A Framework, Sagar Mekala, Shahu Chatrapati Kaila, Jyothi Rani Matang

Makara Journal of Technology

Wireless devices are now being adapted for diverse purposes, such as healthcare, agriculture, transportation, and tactical operations, which present challenges in network formation owing to high device mobility. Current methods rely on discovery techniques for forming wireless sensor networks (WSNs); however, the existing research has been criticized for its high time complexity and redundant neighbor discovery process. In this study, we provide a hybrid strategy to effectively handle the difficulties of locating neighboring nodes in WSNs. Our method combines several strategies to produce precise and effective neighbor detection. Herein, shared memory–based discovery, a beacon technique, and range and distance overlap …

Optimal Load Shedding During Service Restoration In Electrical Secondary Distribution Network Based On Reinforcement Learning, Rukia J. Mwifunyi

Tanzania Journal of Engineering and Technology (TJET)

Increased stress in traditional power systems results in blackouts due to voltage instability attributed to a mismatch between available capacity and load demand, especially in distribution networks. Service restoration schemes are designed to return power supply to the affected parts of the networks. The availability of insufficient supply is a complex problem that requires operational experience or an automatic system. The stochastic nature of load demand significantly impacts service restoration as it results in increased restored demand in case a fault occurs during off-peak hours and helps reduce overload if the fault occurs during peak hours. The study adopts an …

Production Of Biofertilizer From Fruit And Garden Waste, Neema Msuya

Tanzania Journal of Engineering and Technology (TJET)

The project focused on the production of bio-fertilizer from fruit and garden waste, with a specific emphasis on utilizing pineapple tops in the composting process. The objective was to produce and assess the properties of the bio fertilizer obtained from this process and evaluate its potential application in agriculture. In this study, the composting process was done in a 0.7 m long, 0.85 wide and 1.1 m high vessel, and 0.238 m3 pineapple top wastes, resulting in 0.35 m3 of biofertilizer. The bio fertilizer produced exhibited favorable characteristics, including a moisture content of 36%, pH of 7.1, and a total …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Comparison Of Meteorological Drought Indices In Tanzania Using The Meteorological Drought Monitoring Software Package, Paul Ts Limbu

Tanzania Journal of Engineering and Technology (TJET)

Low precipitation, substantial evaporation, and an unequal distribution of precipitation throughout the area are the characteristics of drought, a climatic abnormality. This study used the Meteorological Drought Monitoring (MDM) software and monthly rainfall data from the Tanzania Meteorological Authority (TMA) to examine and compare the Deciles Index (DI), Standardised Precipitation Index (SPI), Percent of Normal Index (PNI), Rainfall Anomaly Index (RAI), Z-Score Index (ZSI), China-Z Index (CZI), and Modified China-Z Index (MCZI) for drought monitoring in Tanzania from 1988 to 2017. It was found that ZSI represented the dry years better than other indices, followed by DI, RAI, PNI, SPI, …

Study Of The Effects Of Thermal Aging Coupled With Shot-Peening Treatment Of Carbonitrided Din 1.6587 Low Alloy Steel On Retained Austenite And Residual Stresses, Richard J. Katemi

Tanzania Journal of Engineering and Technology (TJET)

This work investigated the effects of thermal aging and shot-peening of carbonitrided 1.6587 steel grade on retained austenite and residual stresses. After carbonitriding samples contained maximum of 0.87% carbon, 0.34% nitrogen and 50 mass. -% retained austenite. Thermal aging conditions investigated were -30°C, 90°C and 150°C while the aging period were 14, 96 and 720 hours. After thermal aging, some of the samples were subjected to shot-peening treatment using standard cut wire shots StD – G3 - 0.6 mm VDFI 8001 with intensity in the range of 0.25 to 0.30 mmA and coverage of 1.00 to 1.24 x 98%. It …

Effects Of Bending And Re-Bending On Mechanical Properties Of Locally-Manufactured Steel Rebars, Patrick W. Waruhiu, Simon I. Marandu, Mussa I. Mgwatu

Tanzania Journal of Science

Steel rebars experience deformation when subjected to bending and re-bending operations. Subsequently, their microstructures are impaired thus affecting the mechanical properties and leading to failure. This study establishes the effects of bending and re-bending the steel rebars on the mechanical properties. Experiments were conducted to determine the effects of bending and re-bending of the steel rebars. Testing was conducted on Ten virgin and Thirty specimens which were bent and re-bent at 45º, 90º, and 180º, and followed by tensile tests. Yield strength, ultimate tensile strength, elongation, and ultimate tensile strength to yield strength ratio (Rm/Re), were recorded. Results showed the …

Synthesis Algorithm Of Control System Based On Neural Network For The Gas And Oil Process, Jasur Sevinov, Abdishukurov Maqsudovich Shavkat, A.Z. Shodiyorov

Chemical Technology, Control and Management

Automatic control systems in the oil and gas processing are considered. After extraction of natural gas condensate, management of technological parameters plays an important role in its processing. Among the parameter of regulating algorithms, control based on neural network technology was considered. These control systems are created on the basis of algorithms of neural network technology. There are several structures of neural networks according to their structure. Differences in the process of information processing of these branching structures are considered.

Results Of Experimental Study Of Solar Collector Efficiency, Shakhnoza Sultanova, Ajargul Mambetsheripova, Jasur Safarov

Chemical Technology, Control and Management

The article considers the influence of ambient temperature on the drying efficiency depending on the incident solar radiation, changes in the average temperature of the absorber plate depending on the absorbed power, as well as the thermal efficiency of the collector at significant values of coolant flow.

Synthesis Of Local Control Systems For Underwater Units Cleaning Bottom Sediments In Reservoirs, Yuriy Gennadiyevich Shipulin, Zebiniso Akmalovna Zayniddinova

Chemical Technology, Control and Management

The article discusses the issues of synthesizing local control systems for underwater units for cleaning bottom sediments in reservoirs. It is shown that the protection and rational use of natural reservoirs and the fight against their premature siltation is becoming an urgent task.

It is proposed to use small-sized underwater units, consisting of information and measuring devices, to carry out search work for cleaning bottom sediments under water; control systems; actuators and means of communication with humans.

It is shown that the task of controlling the loading of an underwater unit (UU) requires maintaining optimal performance while simultaneously taking into …

Dynamic Characteristics Of Magnetoelectric Linear Actuators Of Control Systems, Мakhmudjon Muxamedovich Аbdullayev, Rasul Ernazar Ogli Abdiev

Chemical Technology, Control and Management

This paper presents the results of studies carried out on magnetoelectric drives that carry out linear movement, models of drives are built and, on their basis, studies of the main indicators associated with the movement of a linear armature are carried out, such as: speed of movement, acceleration, current values, voltage and traction force of the armature. Also presented are the results of a study of magnetoelectric linear motion drives based on an analysis of graphs of their dynamic characteristics.

Study Of Kinetics Of Hydrocarbon Gas Purification With Composite Absorbents, Oybek Aripdjanov, Shavkat Nurullaev, Shodiyakhon Azimova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the work is to improve the process of natural gas purification from acidic components using a composite absorbent. To study the sorption of acidic components in the gas composition, a chromatographic analysis method was used. The kinetics and rate of corrosion of carbon steel grade st.10 when using composite absorbents MDEA +DEA + AVRP have been studied. The results of the study show that the volume of absorption increased from 0.55 mol/mol to 0.65 mol/mol, and the amount of H₂S in the purified gas decreased from 0.022 g/m³ to 0.014 g/m³. Corrosion …

Study Of Reactive Distillation Equipment For Eterification Process, Abbos Elmanov, Abdulaziz Bakhtiyorov, Adham Norkobilov, Olimjon Maksudov, Zarif Oripov

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this work is to study the chemical technological processes for eterification processes, and the reactive distillation unit, which carries out the reaction and separation process in one device, was chosen as the object of research. А reаctive distillаtion system is exаmined to produce for the production of Ethyl Acetate (EtAc) viа eterificаtion of acetic acid (HAc) with ethаnol. Optimizаtion methods using sensitivity analysis аre аlso conducted. Cаlculаtion of vаpor liquid equilibrium of the mixture system is done using UNIFАC model. Heat integration from the distillate stream of the column to the acid feed stream and from bottom …

Modeling And Performance Analysis Of Solid Oxide Fuel Cell, Mariya Pecherskaya, Khakimjan Butanov, Suhrob A. Ibodullaev, Olim Ruzimuradov, Shavkat Mamatkulov

CHEMISTRY AND CHEMICAL ENGINEERING

A three-dimensional numerical model of the system configurations of various types of solid oxide fuel cells (SOFCs) is used and the effect of parameters on SOFC performance is numerically investigated using COMSOL Multiphysics. The effect of parameters such as support layer thickness, operating temperature, and electrode porosity are shown in the polarization and power curves for each model. The results of the study showed the advantages of the anode-supported SOFC compared to cathode- and electrolyte-supported SOFC.

Theoretical calculations demonstrate the highest output power density in the anode-supported SOFC at 900 ℃, and reach a value of 0.585 W cm^{-2 …}