Engineering Commons^™

Shear Behavior Of Fibrous Reinforced Concrete Short Columns, Feraidoon K. Kashani

Theses

The objective of this investigation was to examine the shear behavior of axially loaded fibrous reinforced concrete short columns under double curvature bending. Eleven columns with modeled dimensions of 6 in. by 41/2 in. with only different fiber volume fraction V_f and shear span ratios were tested under double curvature bending.

The material properties of fibrous concrete is briefly discussed on how the addition of fibers benefits the concrete mix. The results of the compressive and tensile behavior of fibrous concrete is presented. The behavior of bending on reinforced fibrous concrete columns is also briefly discussed.

Previous investigation results, …

An Analysis For The Blade Coating Of Ctbn Modified Epoxy Adhesive, Jeng-Li Liang

Theses

A resin metering criterion has been developed for processing the prepregs of CTBN-EPOXY resin in which the resin content can be controlled within close tolerances. This criterion was obtained by numerically simulating the flow of CTBN-EPDXY resin in the blade-type metering device at room temperature. The Newtonion case of CTBN-EPOXY resin was selected for the study to avoid dealing with more complicated flow equations. A methodology of using the penalty function/finite element formulation was developed to solve the steady state Navior-Stokes equation.

The rheological data show that the CTBN-EPOXY resin is a non-Newtonion fluid at low shear rate. On the …

A Parameter Identification System For The Human Visual Evoked Response, Robert Kalle Michaels

Theses

The Human Visual Evoked Response (VER) provides a useful tool for analyzing an individual's visual system. However, mere inspection of the signal may not always be the best way to make a diagnosis of the patient. To aid in this diagnosis a parameter identification system has been developed which fits the response to an analog model. The development of the model was based on the results of a survey of previous work in the field. Data were acquired from a data acquisition/processing system developed at the New Jersey University of Medicine and Dentistry and the Eye Institute of New Jersey. …

Designing A Data Management System To Support A Quality Control Mission, Erastus Runji Muchioki

Theses

This thesis is concerned with the design of a Data Management System to support a Quality Control Mission particularly within the writer's organization. It defines the term quality, with respect to his company's needs, followed by an outline of quality control management's responsibilities. Problems of quality Control from product design, assembly to the finished product are discussed. The organization's current quality control procedures are analyzed. Problems in establishing the data base are discussed. This data is then organized to form the new Data Management System that will support a Quality Control Mission properly. In the discussion, the author tries to …

Managing In The Technical Sales Arena, Robert Munro

Theses

The major objective of this thesis is to portray the role of a Field Engineer for a major manufacturer of electrical distribution and control equipment. In so doing, it should represent a reasonable facsimile of what a sales manager of a large Field Office, comprised of approximately twelve Field Engineers, would encounter in his supervisory capacity. As such, it should provide information for those interested in entering and hoping to manage in technical sales career.

While much of the information was derived from books, periodicals, and conversations with people associated with the electrical industry, the major portion of the work …

Automated Instrumentation System For Studies Of Metabolic Rates In Rats, Suhas P. Pathak

Theses

The task of the instrumentation system is to measure the respiratory exchange in rats in a controlled experiment. Air is drawn at a predeter-mined rate in and out of rat chambers. The proportion of oxygen and carbon dioxide in the ensuing air indicates the respiratory rate of the rat. The entire operation is controlled by a microcomputer whose most important functions are: to direct the flow of air through the rat chambers by switching valves; and to collect data about the percentages of gases in question.

Thus with the help of a computer it is possible to monitor and control …

Criteria Measurement In Edp Auditing, Eugene Alexander Ottaviano

Theses

Criteria Measurement in EDP Auditing is a planning technique to assist the Internal Audit function in systematically selecting software applications for budgeted audit reviews. The objective is to develop a risk analysis method, which is not time and labor intensive, that will minimize risk to the corporation and maximize audit effectiveness. The methodology does not consider probabilities or occurrence rates because risks to the EDP environment are extremely difficult to forecast with traditional techniques. The method provides for both objective and subjective risk determinations.

The approach is to measure software risk criteria for a specific data processing environment. Risk concerns …

The Hydroxide-, Chymotrypsin-, And Blood-Catalyzed Hydrolysis Of A Series Of Sodium 4-Acyloxy-3-Nitrobenzene Sulfonates, Louis E. Rinaldi

Theses

The kinetics of the hydrolysis of a series of water-soluble aromatic esters (sodium 4-acyloxy-3-nitrobenzene sulfonates) were analyzed in order to determine the effect of a variety of substitutions (on the α-carbon of the acid group) upon the rate of reaction.

The following was observed. That (a), the hydroxide catalyzed and water dependent hydrolyses of these esters are slower for larger substituents and faster for smaller ones. That (b), the chymotrypsin catalytic hydrolysis of these esters shows an acylation reaction step which occurs at a rate greater than deacylation for larger substituents, and at approximately equal rates for smaller ones. Furthermore, …

Gallium Nitride Film Deposition By Ionized Cluster Beam Epitaxy, Ghulum Bakiri

Theses

An experimental Ionized Cluster Beam System similar in design to the one developed at Kyoto University in Japan was. designed and constructed in the Microelectronics Laboratory at NJIT. This involved making the working drawings, having the parts machined and then assembling the system in a vacuum system together with the necessary variable power supplies, meters, controls, gas inlets, cooling water connections, etc.

Eleven deposition runs were then attempted to grow gallium nitride utilizing the system constructed. In a typical deposition run, gallium was vaporized from a boron nitride crucible at 1000° C and allowed to expand through a 0.5 mm …

An Improvement In The Chemical Engineering Simulation System, Roman Andreyuk

Theses

The accurate design of chemical processing plants is important to the chemical engineer. The original version of CHESS (Chemical Engineering Simulation System) greatly reduced the amount of time which previously had to be spent on the design of such plants by providing the engineer with a package which simulated some of the more common pieces of chemical processing equipment found in a typical chemical plant.

The present version of the Chemical Engineering Simulation System (CHESS2) presents a significant improvement over the original version. The improvement was achieved by expanding the thermodynamic package, offering the user a choice of methods by …

A Finite Difference Solution Of An Ideal, Normal, Impinging Jet, Luis A. Gast

Theses

The free boundary of a circular jet of an irrotational, inviscid, incompressible, fluid impinging normally to a flat surface from a height of 2 times the nozzle radius, was found by a finite difference method.

Starting with a graphical solution, approximate values of the potential were given to the nodes at the field.

Having the equipotential lines perpendicular to the axis of the jet, perpendicular to the impinging surface, and having defined the value of the potential at both the entrance and exit of the jet, a finite difference expression of the Laplace's equation was used in an iteration scheme …

An Application Of Personal Microcomputer To Solve Mid-Sized Goal Programming Problems, Chanhon Joe Lu

Theses

This thesis develops a microcomputer software to solve mid-sized goal programming problems utilizing the revised simplex method.

Goal programming is an extension of linear programming, but is more powerful and flexible than linear programming because of its capability in handling problems with multiple conflicting objectives, instead of dealing with "one dimensional" objective - profit maximization or cost minimization. Accordingly, goal programming is very useful to the complex organizational environments.

With the help of rapid and accurate computation of digital computers, solving a complex program is not a difficult task at all. However, some medium-sized companies cannot afford a mainframe -computer, …

Behavior Of Composite Steel-Fibrous Concrete Beams, Avijit Mookerjee

Theses

This research thesis on composite steel-fibrous concrete is based on a series of beam tests conducted in the Structural and Concrete Laboratory of the New Jersey Institute of Technology.

In the first series of tests, two twenty-foot two-span continuous beams were tested. In the first beam, plain reinforced concrete was used in the construction of the composite beam. The second beam had 1.5% by volume of steel fibers in the concrete.

In the second series, four composite T-beams were tested. Two of the beams had 1% of steel fibers by volume. The other two beams were constructed using plain concrete. …

Organizing To Manage Future Information Technologies, John Patrick Paczkowski

Theses

The area of information technology has undergone dramatic changes over the past ten years, and the rate of change is expected to continue to accelerate through the 1980's and beyond. The newly developing information systems are providing organizations with numerous options for enhancing the quality of managerial decision making, speeding communications and improving the efficiency and effectiveness of administrative/office processes. Unfortnately, many organizations are discovering that they are unable to effectively assimilate and utilize the technology effectively. Chief executives are finding that the traditional structures for managing Data Processing, Telecommunications, and office systems are often fragmented, lack the technical expertise …

Nomographs And Tables For Simplified Thermal Analysis Of Power Piping, Dhanjibhai N. Patel

Theses

This Thesis develops Nomographs and Tables for simplified thermal analysis of " Power Piping." It gives the length of required Thermal Relieve Leg when a set of piping parameters such as, pipe size, pipe material, operating temperature and pipe length are given.

The Nomographs and Tables developed here can be used

1. to determine the primary piping layout, piping route, support location etc. before vigorous conputer analysis is performed.

2. to help the Field Engineer on the plant site to make " on the spot " decisions on pending piping route changes.

Two Nomographs are developed in this Thesis. One …

Failure Surface For L-Shaped Reinforced Concrete Short Columns, Mon-Chen Liu

Theses

Combined bending and axial compression for L-shaped reinforced concrete short columns is a common problem. But the present ACI Building Code (ACI 318-77), handbooks and texbooks pay no attention to this problem. A numerical analysis and computer program developed by Hsu fora reinforced concrete member subject to biaxial bending and axial load has been used Using this computer program, the interaction diagrams and failure surface were developed for L-shaped members under combined bending and axial compression. A comparison between theoretical and experimental results was included to examine the validity of failure surface.

Moment Method Solution Of The Time-Dependent Transport Equation To Describe The Scattering Of Gaussian Plane Wave Pulses By A Forest, Nack Yang Cho

Theses

The time dependent transport equation is used to study the transmission of periodic pulses through a forest. The forest is assumed to occupy a half-space region, to be statistically homogeneous and to scatter energy isotropically A periodic sequence of Gaussian plane wave pulses is assumed to enter the forest normally from free space. The transport equation is solved by the moment method using triangular expansion functions. Numerical results indicate the dependence of the incoherent intensity on penetration depth, observation angle, albedo and pulse repetition rate.

Numerical Solution Of Navier-Stokes Equation By Finite Element Method, Kuan-Tzong Lee

Theses

A finite element method for solving the entrance flow in a parallel-plate channal at low Reynolds number has been studied. Two methods of formulation for both incompressible viscous and inviscid fluid flows were developed. The first uses stream function and potential function as field variables while the second uses velocity and pressure. Both formulations presented here ultilized variational principle and weighted residual method. The numerical example was solved by constrained variational principle with penalty functions in conjunction with the Newton-Raphson method. A 9-node quadratic quadrilateral element was used in this example. Numerical results for entrance flow problem were obtained for …

Computer Aided Analysis Of Electroencephalographic Waveforms, Edward Tadeusz Polkowski

Theses

An approach to analysis of EEG waveforms is described. The procedure utilizes a PDP -11 computer to perform a Fast Fourier Transform on four channels of data simultaneously. The transforms are done in real time and. the results are plotted in a manner which allows the operator to easily determine the major background activity and to check for left-right symmetries in brain waves. Patient data is used to verify the computer output against actual clinical diagnoses.

Steady State Heat Transfer From Two Concentric Rings Of Spheres, Kevin J. Fitzpatrick

Theses

The method of reflections was used to solve the steady state heat transfer problem for two concentric rings of spheres, all at equal surface temperature. The method results in a mathematical model for the three dimensional temperature profiles around the array of spheres. This model is used to develop an expression for heat transfer rate from the array. This work has resulted in a solution for dilute systems since no ring to ring interaction term was found.

On The Analysis And Design Of Clamped Rectangular Plate With Partial Load, Yacin Saaid Jaboury

Theses

In this Thesis, maximum deflection and bending moments of a partially loaded clamped rectangular plate are studied. The loading is uniformly applied to a retangular area proportional to the shape.

Navier's Solutions on partially loaded simply supported rectangular plate is superimposed with edge moments to give the clamped boundry condition.

Solutions of maximum deflection and bending moments are derived in Double Series form. A Fortran program is employed in obtaining the numerical results. When the partially loaded area approaches zero it becomes a centrally loaded case; and when loading area to plate area ratio approaches unity it becomes a uniformly …

Behavior Of Reinforced Fibrous Beam-Column Joints Under Cyclic Loads, Sitaram Mahadev

Theses

From exploratory research of reinforced fibrous concrete, it has been shown that fibrous concrete is potentially superior and less costly than the conventional reinforced concrete.

The testing program consisted of ten beam-column joints with half of these joints containing 1-1/2 percent hooked end fibers. The beam column joints were constructed with less hoops than a conventional seismic joint would have, according to design specifications of the American Concrete Institute Code (ACI 318-77). In studying the behavior of these beam-column joints, two loading cases were examined:

(1) critical regions whose inelastic behavior was controlled by bending, and

(2) critical regions whose …

Error Detection For Data Communication Systems, John Biancamano

Theses

A description of the problems encountered in the data communications field and the various solutions can be found in a number of diverse, and often theoretical sources. My intention in writing this thesis is to bring together, in a practical and understandable manner, the theory and the application of a method of error detection used extensively in data communication systems known as the Cyclic Redundancy Check (CRC).

To provide some background on the subject, a description of a data communication system is presented, and the possible sources of error are explored in some detail. Data transmission formats are described, and …

Flow Tube Reactions Of Selected Chlorocarbons With Molecular Hydrogen Or Water Vapor In A Microwave Induced Plasma Reactor, Robert Benedict Barat

Theses

The reactions of various chlorinated hydrocarbons with molecular hydrogen or water vapor have been studied in a microwave plasma tubular flow reactor. The investigation of such reactions is desirable because the often toxic parent chlorocarbons are transformed to more thermodynamically stable and relatively non-toxic products by removal of' chlorine atoms as hydrogen chloride. Present detoxification technologies generally employ thermal oxidation as a means of disposal of chlorocarbons, which does not offer a thermodynamically stable sink for the chlorine atoms.

The experimental apparatus included feed introduction systems, a microwave plasma reactor, and full product analyses. The feed systems enabled use of …

Nonlinear Analysis Of Shear Walls And Shear Panels By Finite Element Method, Erhan Atay

Theses

The objective of this work was to determine the feasibility of applying the Finite Element Method to Nonlinear Analyses of Shear Walls and Shear Panels.

Various existing methods are reviewed and discussed.

These studies determined that the application of Finite Element Method to Nonlinear Analysis of Shear Walls and Shear Panels is being misused in many cases but is very practical and promising where justified. However more studies are needed for the manner of modeling to be used to connect the wall to beam and slab elements that frame into that wall. To model the coupled beams as plane stress …

Adaptive Delta Modulation, Aliuddin Ahmad

Theses

The objective of this thesis is the study of the performance of instantaneously companded adaptive delta modulation (ADM) systems in comparison with linear delta modulation (LDM) in terms of signal to quantization noise ratio (SNR). Various schemes for ADM are discussed and their advantages and disadvantages are indicated. SNRs are calculated by simulation, with IBM's continuous system modeling programming (CSMP) language being used as a tool for simulation. LDM, first and second order constant factor delta modulation (CFDM), has been simulated and responses for different types of input signals are presented.

A Modified Unifac Model For The Prediction Of Henry's Constants, Carlos Alberto Marques Antunes

Theses

A group-contribution model for the correlation and prediction of Henry's constants in single solvents is presented. The mode: involves a one-parameter per gas/ solvent group pair UNIFAC expression extended to incorcorate free volume effects. The model is applied to three gases, CH₄, N₂, and O₂ in alkane solvents and in water. Good results, including a successful description of the temperature dependency of the Henry's constants, are obtained with typical accuracy of ± 10%.

Transportation Alternatives For Peak Period Passenger Travel In Greater Georgetown, Ahamad Baksh

Theses

Alternatives to present a workable and cost effective solution(s) to the inadequate supply of public transportation during the peak hour periods in Greater Georgetown (Guyana) are examined. Various transportation system management strategies that could help in either to service the peak period demands by more effective utilization of available transport resources or to manage these demands by altering peaks patterns, are discussed. Data from the transportation study aspect of the "Physical Plan for Greater Georgetown", conducted by the Central Housing and Planning Authority as well as data from the files of the Central Transport Planning Unit of the Ministry of …

Leachate Treatment Technique Utilizing Fly Ash As A Low Cost Sorbent, Turan A. Ramadan

Theses

This study was carried out to design a system for the inexpensive treatment of ash pond effluent or leachate. Twelve different coals were burned in three different types of coal fired boilers to determine the influence of coal composition, ash fusion temperatures, boiler additives, combustion conditions and co-firing of natural gas or oil with the coal, on the composition of the fly ash and bottom ash as well as the leaching and sorbate characteristics of the fly ash produced.

The trace elemental analysis consisting of Ti, Cd, Sn, Ni, Pb, Mo, Cu, Cr. Zn, Mn, Ba, and V in the …

Investigation Of Mental Workload In A Visual Inspection Task, Michel Alfandari

Theses

This thesis consists of an investigation of the "mental workload" involved in a visual inspection task. A short-term laboratory experiment was conducted on twenty test subjects to study the effects of three typical job-related factors encountered in mental workload situations: load stress, time stress, and motivation. These effects were assessed through the subjects' performances as measured by speed and accuracy data. The analysis of the results revealed that an increase in load stress deteriorates both speed and accuracy, whereas time stress improves speed but only at the expense of accuracy. The expected positive influence of motivational factor (cash prizes) was …